linux/drivers/spi/Kconfig

1424 lines
44 KiB

[PATCH] spi: simple SPI framework This is the core of a small SPI framework, implementing the model of a queue of messages which complete asynchronously (with thin synchronous wrappers on top). - It's still less than 2KB of ".text" (ARM). If there's got to be a mid-layer for something so simple, that's the right size budget. :) - The guts use board-specific SPI device tables to build the driver model tree. (Hardware probing is rarely an option.) - This version of Kconfig includes no drivers. At this writing there are two known master controller drivers (PXA/SSP, OMAP MicroWire) and three protocol drivers (CS8415a, ADS7846, DataFlash) with LKML mentions of other drivers in development. - No userspace API. There are several implementations to compare. Implement them like any other driver, and bind them with sysfs. The changes from last version posted to LKML (on 11-Nov-2005) are minor, and include: - One bugfix (removes a FIXME), with the visible effect of making device names be "spiB.C" where B is the bus number and C is the chipselect. - The "caller provides DMA mappings" mechanism now has kerneldoc, for DMA drivers that want to be fancy. - Hey, the framework init can be subsys_init. Even though board init logic fires earlier, at arch_init ... since the framework init is for driver support, and the board init support uses static init. - Various additional spec/doc clarifications based on discussions with other folk. It adds a brief "thank you" at the end, for folk who've helped nudge this framework into existence. As I've said before, I think that "protocol tweaking" is the main support that this driver framework will need to evolve. From: Mark Underwood <basicmark@yahoo.com> Update the SPI framework to remove a potential priority inversion case by reverting to kmalloc if the pre-allocated DMA-safe buffer isn't available. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-08 13:34:19 -08:00
[PATCH] spi: simple SPI framework This is the core of a small SPI framework, implementing the model of a queue of messages which complete asynchronously (with thin synchronous wrappers on top). - It's still less than 2KB of ".text" (ARM). If there's got to be a mid-layer for something so simple, that's the right size budget. :) - The guts use board-specific SPI device tables to build the driver model tree. (Hardware probing is rarely an option.) - This version of Kconfig includes no drivers. At this writing there are two known master controller drivers (PXA/SSP, OMAP MicroWire) and three protocol drivers (CS8415a, ADS7846, DataFlash) with LKML mentions of other drivers in development. - No userspace API. There are several implementations to compare. Implement them like any other driver, and bind them with sysfs. The changes from last version posted to LKML (on 11-Nov-2005) are minor, and include: - One bugfix (removes a FIXME), with the visible effect of making device names be "spiB.C" where B is the bus number and C is the chipselect. - The "caller provides DMA mappings" mechanism now has kerneldoc, for DMA drivers that want to be fancy. - Hey, the framework init can be subsys_init. Even though board init logic fires earlier, at arch_init ... since the framework init is for driver support, and the board init support uses static init. - Various additional spec/doc clarifications based on discussions with other folk. It adds a brief "thank you" at the end, for folk who've helped nudge this framework into existence. As I've said before, I think that "protocol tweaking" is the main support that this driver framework will need to evolve. From: Mark Underwood <basicmark@yahoo.com> Update the SPI framework to remove a potential priority inversion case by reverting to kmalloc if the pre-allocated DMA-safe buffer isn't available. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-08 13:34:19 -08:00
[PATCH] spi: simple SPI framework This is the core of a small SPI framework, implementing the model of a queue of messages which complete asynchronously (with thin synchronous wrappers on top). - It's still less than 2KB of ".text" (ARM). If there's got to be a mid-layer for something so simple, that's the right size budget. :) - The guts use board-specific SPI device tables to build the driver model tree. (Hardware probing is rarely an option.) - This version of Kconfig includes no drivers. At this writing there are two known master controller drivers (PXA/SSP, OMAP MicroWire) and three protocol drivers (CS8415a, ADS7846, DataFlash) with LKML mentions of other drivers in development. - No userspace API. There are several implementations to compare. Implement them like any other driver, and bind them with sysfs. The changes from last version posted to LKML (on 11-Nov-2005) are minor, and include: - One bugfix (removes a FIXME), with the visible effect of making device names be "spiB.C" where B is the bus number and C is the chipselect. - The "caller provides DMA mappings" mechanism now has kerneldoc, for DMA drivers that want to be fancy. - Hey, the framework init can be subsys_init. Even though board init logic fires earlier, at arch_init ... since the framework init is for driver support, and the board init support uses static init. - Various additional spec/doc clarifications based on discussions with other folk. It adds a brief "thank you" at the end, for folk who've helped nudge this framework into existence. As I've said before, I think that "protocol tweaking" is the main support that this driver framework will need to evolve. From: Mark Underwood <basicmark@yahoo.com> Update the SPI framework to remove a potential priority inversion case by reverting to kmalloc if the pre-allocated DMA-safe buffer isn't available. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-08 13:34:19 -08:00
[PATCH] spi: simple SPI framework This is the core of a small SPI framework, implementing the model of a queue of messages which complete asynchronously (with thin synchronous wrappers on top). - It's still less than 2KB of ".text" (ARM). If there's got to be a mid-layer for something so simple, that's the right size budget. :) - The guts use board-specific SPI device tables to build the driver model tree. (Hardware probing is rarely an option.) - This version of Kconfig includes no drivers. At this writing there are two known master controller drivers (PXA/SSP, OMAP MicroWire) and three protocol drivers (CS8415a, ADS7846, DataFlash) with LKML mentions of other drivers in development. - No userspace API. There are several implementations to compare. Implement them like any other driver, and bind them with sysfs. The changes from last version posted to LKML (on 11-Nov-2005) are minor, and include: - One bugfix (removes a FIXME), with the visible effect of making device names be "spiB.C" where B is the bus number and C is the chipselect. - The "caller provides DMA mappings" mechanism now has kerneldoc, for DMA drivers that want to be fancy. - Hey, the framework init can be subsys_init. Even though board init logic fires earlier, at arch_init ... since the framework init is for driver support, and the board init support uses static init. - Various additional spec/doc clarifications based on discussions with other folk. It adds a brief "thank you" at the end, for folk who've helped nudge this framework into existence. As I've said before, I think that "protocol tweaking" is the main support that this driver framework will need to evolve. From: Mark Underwood <basicmark@yahoo.com> Update the SPI framework to remove a potential priority inversion case by reverting to kmalloc if the pre-allocated DMA-safe buffer isn't available. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-08 13:34:19 -08:00
[PATCH] spi: simple SPI framework This is the core of a small SPI framework, implementing the model of a queue of messages which complete asynchronously (with thin synchronous wrappers on top). - It's still less than 2KB of ".text" (ARM). If there's got to be a mid-layer for something so simple, that's the right size budget. :) - The guts use board-specific SPI device tables to build the driver model tree. (Hardware probing is rarely an option.) - This version of Kconfig includes no drivers. At this writing there are two known master controller drivers (PXA/SSP, OMAP MicroWire) and three protocol drivers (CS8415a, ADS7846, DataFlash) with LKML mentions of other drivers in development. - No userspace API. There are several implementations to compare. Implement them like any other driver, and bind them with sysfs. The changes from last version posted to LKML (on 11-Nov-2005) are minor, and include: - One bugfix (removes a FIXME), with the visible effect of making device names be "spiB.C" where B is the bus number and C is the chipselect. - The "caller provides DMA mappings" mechanism now has kerneldoc, for DMA drivers that want to be fancy. - Hey, the framework init can be subsys_init. Even though board init logic fires earlier, at arch_init ... since the framework init is for driver support, and the board init support uses static init. - Various additional spec/doc clarifications based on discussions with other folk. It adds a brief "thank you" at the end, for folk who've helped nudge this framework into existence. As I've said before, I think that "protocol tweaking" is the main support that this driver framework will need to evolve. From: Mark Underwood <basicmark@yahoo.com> Update the SPI framework to remove a potential priority inversion case by reverting to kmalloc if the pre-allocated DMA-safe buffer isn't available. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-08 13:34:19 -08:00
[PATCH] spi: simple SPI framework This is the core of a small SPI framework, implementing the model of a queue of messages which complete asynchronously (with thin synchronous wrappers on top). - It's still less than 2KB of ".text" (ARM). If there's got to be a mid-layer for something so simple, that's the right size budget. :) - The guts use board-specific SPI device tables to build the driver model tree. (Hardware probing is rarely an option.) - This version of Kconfig includes no drivers. At this writing there are two known master controller drivers (PXA/SSP, OMAP MicroWire) and three protocol drivers (CS8415a, ADS7846, DataFlash) with LKML mentions of other drivers in development. - No userspace API. There are several implementations to compare. Implement them like any other driver, and bind them with sysfs. The changes from last version posted to LKML (on 11-Nov-2005) are minor, and include: - One bugfix (removes a FIXME), with the visible effect of making device names be "spiB.C" where B is the bus number and C is the chipselect. - The "caller provides DMA mappings" mechanism now has kerneldoc, for DMA drivers that want to be fancy. - Hey, the framework init can be subsys_init. Even though board init logic fires earlier, at arch_init ... since the framework init is for driver support, and the board init support uses static init. - Various additional spec/doc clarifications based on discussions with other folk. It adds a brief "thank you" at the end, for folk who've helped nudge this framework into existence. As I've said before, I think that "protocol tweaking" is the main support that this driver framework will need to evolve. From: Mark Underwood <basicmark@yahoo.com> Update the SPI framework to remove a potential priority inversion case by reverting to kmalloc if the pre-allocated DMA-safe buffer isn't available. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-08 13:34:19 -08:00
[PATCH] spi: simple SPI framework This is the core of a small SPI framework, implementing the model of a queue of messages which complete asynchronously (with thin synchronous wrappers on top). - It's still less than 2KB of ".text" (ARM). If there's got to be a mid-layer for something so simple, that's the right size budget. :) - The guts use board-specific SPI device tables to build the driver model tree. (Hardware probing is rarely an option.) - This version of Kconfig includes no drivers. At this writing there are two known master controller drivers (PXA/SSP, OMAP MicroWire) and three protocol drivers (CS8415a, ADS7846, DataFlash) with LKML mentions of other drivers in development. - No userspace API. There are several implementations to compare. Implement them like any other driver, and bind them with sysfs. The changes from last version posted to LKML (on 11-Nov-2005) are minor, and include: - One bugfix (removes a FIXME), with the visible effect of making device names be "spiB.C" where B is the bus number and C is the chipselect. - The "caller provides DMA mappings" mechanism now has kerneldoc, for DMA drivers that want to be fancy. - Hey, the framework init can be subsys_init. Even though board init logic fires earlier, at arch_init ... since the framework init is for driver support, and the board init support uses static init. - Various additional spec/doc clarifications based on discussions with other folk. It adds a brief "thank you" at the end, for folk who've helped nudge this framework into existence. As I've said before, I think that "protocol tweaking" is the main support that this driver framework will need to evolve. From: Mark Underwood <basicmark@yahoo.com> Update the SPI framework to remove a potential priority inversion case by reverting to kmalloc if the pre-allocated DMA-safe buffer isn't available. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-08 13:34:19 -08:00
[PATCH] spi: simple SPI framework This is the core of a small SPI framework, implementing the model of a queue of messages which complete asynchronously (with thin synchronous wrappers on top). - It's still less than 2KB of ".text" (ARM). If there's got to be a mid-layer for something so simple, that's the right size budget. :) - The guts use board-specific SPI device tables to build the driver model tree. (Hardware probing is rarely an option.) - This version of Kconfig includes no drivers. At this writing there are two known master controller drivers (PXA/SSP, OMAP MicroWire) and three protocol drivers (CS8415a, ADS7846, DataFlash) with LKML mentions of other drivers in development. - No userspace API. There are several implementations to compare. Implement them like any other driver, and bind them with sysfs. The changes from last version posted to LKML (on 11-Nov-2005) are minor, and include: - One bugfix (removes a FIXME), with the visible effect of making device names be "spiB.C" where B is the bus number and C is the chipselect. - The "caller provides DMA mappings" mechanism now has kerneldoc, for DMA drivers that want to be fancy. - Hey, the framework init can be subsys_init. Even though board init logic fires earlier, at arch_init ... since the framework init is for driver support, and the board init support uses static init. - Various additional spec/doc clarifications based on discussions with other folk. It adds a brief "thank you" at the end, for folk who've helped nudge this framework into existence. As I've said before, I think that "protocol tweaking" is the main support that this driver framework will need to evolve. From: Mark Underwood <basicmark@yahoo.com> Update the SPI framework to remove a potential priority inversion case by reverting to kmalloc if the pre-allocated DMA-safe buffer isn't available. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-08 13:34:19 -08:00
spi: spi-mem: Convert Aspeed SMC driver to spi-mem This SPI driver adds support for the Aspeed static memory controllers of the AST2600, AST2500 and AST2400 SoCs using the spi-mem interface. * AST2600 Firmware SPI Memory Controller (FMC) . BMC firmware . 3 chip select pins (CE0 ~ CE2) . Only supports SPI type flash memory . different segment register interface . single, dual and quad mode. * AST2600 SPI Flash Controller (SPI1 and SPI2) . host firmware . 2 chip select pins (CE0 ~ CE1) . different segment register interface . single, dual and quad mode. * AST2500 Firmware SPI Memory Controller (FMC) . BMC firmware . 3 chip select pins (CE0 ~ CE2) . supports SPI type flash memory (CE0-CE1) . CE2 can be of NOR type flash but this is not supported by the driver . single, dual mode. * AST2500 SPI Flash Controller (SPI1 and SPI2) . host firmware . 2 chip select pins (CE0 ~ CE1) . single, dual mode. * AST2400 New Static Memory Controller (also referred as FMC) . BMC firmware . New register set . 5 chip select pins (CE0 ∼ CE4) . supports NOR flash, NAND flash and SPI flash memory. . single, dual and quad mode. Each controller has a memory range on which flash devices contents are mapped. Each device is assigned a window that can be changed at bootime with the Segment Address Registers. Each SPI flash device can then be accessed in two modes: Command and User. When in User mode, SPI transfers are initiated with accesses to the memory segment of a device. When in Command mode, memory operations on the memory segment of a device generate SPI commands automatically using a Control Register for the settings. This initial patch adds support for User mode. Command mode needs a little more work to check that the memory window on the AHB bus fits the device size. It will come later when support for direct mapping is added. Single and dual mode RX transfers are supported. Other types than SPI are not supported. Reviewed-by: Joel Stanley <joel@jms.id.au> Tested-by: Joel Stanley <joel@jms.id.au> Tested-by: Tao Ren <rentao.bupt@gmail.com> Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com> Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com> Signed-off-by: Cédric Le Goater <clg@kaod.org> Link: https://lore.kernel.org/r/20220509175616.1089346-4-clg@kaod.org Signed-off-by: Mark Brown <broonie@kernel.org>
2022-05-09 19:56:08 +02:00
spi: Add Analog Devices AXI SPI Engine controller support This patch adds support for the AXI SPI Engine controller which is a FPGA soft-peripheral which is used in some of Analog Devices' reference designs. The AXI SPI Engine controller is part of the SPI Engine framework[1] and allows memory mapped access to the SPI Engine control bus. This allows it to be used as a general purpose software driven SPI controller. The SPI Engine in addition offers some optional advanced acceleration and offloading capabilities, which are not part of this patch though and will be introduced separately. At the core of the SPI Engine framework is a small sort of co-processor that accepts a command stream and turns the commands into low-level SPI transactions. Communication is done through three memory mapped FIFOs in the register map of the AXI SPI Engine peripheral. One FIFO for the command stream and one each for transmit and receive data. The driver translates a spi_message in a command stream and writes it to the peripheral which executes it asynchronously. This allows it to perform very precise timings which are required for some SPI slave devices to achieve maximum performance (e.g. analog-to-digital and digital-to-analog converters). The execution flow is synchronized to the host system by a special synchronize instruction which generates a interrupt. [1] https://wiki.analog.com/resources/fpga/peripherals/spi_engine Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-02-04 17:13:30 +01:00
spi: Add Analog Devices AXI SPI Engine controller support This patch adds support for the AXI SPI Engine controller which is a FPGA soft-peripheral which is used in some of Analog Devices' reference designs. The AXI SPI Engine controller is part of the SPI Engine framework[1] and allows memory mapped access to the SPI Engine control bus. This allows it to be used as a general purpose software driven SPI controller. The SPI Engine in addition offers some optional advanced acceleration and offloading capabilities, which are not part of this patch though and will be introduced separately. At the core of the SPI Engine framework is a small sort of co-processor that accepts a command stream and turns the commands into low-level SPI transactions. Communication is done through three memory mapped FIFOs in the register map of the AXI SPI Engine peripheral. One FIFO for the command stream and one each for transmit and receive data. The driver translates a spi_message in a command stream and writes it to the peripheral which executes it asynchronously. This allows it to perform very precise timings which are required for some SPI slave devices to achieve maximum performance (e.g. analog-to-digital and digital-to-analog converters). The execution flow is synchronized to the host system by a special synchronize instruction which generates a interrupt. [1] https://wiki.analog.com/resources/fpga/peripherals/spi_engine Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-02-04 17:13:30 +01:00
spi: add driver for BCM2835 The BCM2835 contains two forms of SPI master controller (one known simply as SPI0, and the other known as the "Universal SPI Master", in the auxilliary block) and one form of SPI slave controller. This patch adds support for the SPI0 controller. This driver is taken from Chris Boot's repository at git://github.com/bootc/linux.git rpi-linear as of commit 6de2905 "spi-bcm2708: fix printf with spurious %s". In the first SPI-related commit there, Chris wrote: Thanks to csoutreach / A Robinson for his driver which I used as an inspiration. You can find his version here: http://piface.openlx.org.uk/raspberry-pi-spi-kernel-driver-available-for Changes made during upstreaming: * Renamed bcm2708 to bcm2835 as per upstream naming for this SoC. * Removed support for brcm,realtime property. * Increased transfer timeout to 30 seconds. * Return IRQ_NONE from the IRQ handler if no interrupt was handled. * Disable TA (Transfer Active) and clear FIFOs on a transfer timeout. * Wrote device tree binding documentation. * Request unnamed clock rather than "sys_pclk"; the DT will provide the correct clock. * Assume that tfr->speed_hz and tfr->bits_per_word are always set in bcm2835_spi_start_transfer(), bcm2835_spi_transfer_one(), so no need to check spi->speed_hz or tft->bits_per_word. * Re-ordered probe() to remove the need for temporary variables. * Call clk_disable_unprepare() rather than just clk_unprepare() on probe() failure. * Don't use devm_request_irq(), to ensure that the IRQ doesn't fire after we've torn down the device, but not unhooked the IRQ. * Moved probe()'s call to clk_prepare_enable() so we can be sure the clock is enabled if the IRQ handler fires immediately. * Remove redundant checks from bcm2835_spi_check_transfer() and bcm2835_spi_setup(). * Re-ordered IRQ handler to check for RXR before DONE. Added comments to ISR. * Removed empty prepare/unprepare implementations. * Removed use of devinit/devexit. * Added BCM2835_ prefix to defines. Signed-off-by: Chris Boot <bootc@bootc.net> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-03-11 21:38:24 -06:00
spi: add driver for BCM2835 The BCM2835 contains two forms of SPI master controller (one known simply as SPI0, and the other known as the "Universal SPI Master", in the auxilliary block) and one form of SPI slave controller. This patch adds support for the SPI0 controller. This driver is taken from Chris Boot's repository at git://github.com/bootc/linux.git rpi-linear as of commit 6de2905 "spi-bcm2708: fix printf with spurious %s". In the first SPI-related commit there, Chris wrote: Thanks to csoutreach / A Robinson for his driver which I used as an inspiration. You can find his version here: http://piface.openlx.org.uk/raspberry-pi-spi-kernel-driver-available-for Changes made during upstreaming: * Renamed bcm2708 to bcm2835 as per upstream naming for this SoC. * Removed support for brcm,realtime property. * Increased transfer timeout to 30 seconds. * Return IRQ_NONE from the IRQ handler if no interrupt was handled. * Disable TA (Transfer Active) and clear FIFOs on a transfer timeout. * Wrote device tree binding documentation. * Request unnamed clock rather than "sys_pclk"; the DT will provide the correct clock. * Assume that tfr->speed_hz and tfr->bits_per_word are always set in bcm2835_spi_start_transfer(), bcm2835_spi_transfer_one(), so no need to check spi->speed_hz or tft->bits_per_word. * Re-ordered probe() to remove the need for temporary variables. * Call clk_disable_unprepare() rather than just clk_unprepare() on probe() failure. * Don't use devm_request_irq(), to ensure that the IRQ doesn't fire after we've torn down the device, but not unhooked the IRQ. * Moved probe()'s call to clk_prepare_enable() so we can be sure the clock is enabled if the IRQ handler fires immediately. * Remove redundant checks from bcm2835_spi_check_transfer() and bcm2835_spi_setup(). * Re-ordered IRQ handler to check for RXR before DONE. Added comments to ISR. * Removed empty prepare/unprepare implementations. * Removed use of devinit/devexit. * Added BCM2835_ prefix to defines. Signed-off-by: Chris Boot <bootc@bootc.net> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-03-11 21:38:24 -06:00
[PATCH] spi: simple SPI framework This is the core of a small SPI framework, implementing the model of a queue of messages which complete asynchronously (with thin synchronous wrappers on top). - It's still less than 2KB of ".text" (ARM). If there's got to be a mid-layer for something so simple, that's the right size budget. :) - The guts use board-specific SPI device tables to build the driver model tree. (Hardware probing is rarely an option.) - This version of Kconfig includes no drivers. At this writing there are two known master controller drivers (PXA/SSP, OMAP MicroWire) and three protocol drivers (CS8415a, ADS7846, DataFlash) with LKML mentions of other drivers in development. - No userspace API. There are several implementations to compare. Implement them like any other driver, and bind them with sysfs. The changes from last version posted to LKML (on 11-Nov-2005) are minor, and include: - One bugfix (removes a FIXME), with the visible effect of making device names be "spiB.C" where B is the bus number and C is the chipselect. - The "caller provides DMA mappings" mechanism now has kerneldoc, for DMA drivers that want to be fancy. - Hey, the framework init can be subsys_init. Even though board init logic fires earlier, at arch_init ... since the framework init is for driver support, and the board init support uses static init. - Various additional spec/doc clarifications based on discussions with other folk. It adds a brief "thank you" at the end, for folk who've helped nudge this framework into existence. As I've said before, I think that "protocol tweaking" is the main support that this driver framework will need to evolve. From: Mark Underwood <basicmark@yahoo.com> Update the SPI framework to remove a potential priority inversion case by reverting to kmalloc if the pre-allocated DMA-safe buffer isn't available. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-08 13:34:19 -08:00
spi: cadence: add support for Cadence XSPI controller This patch adds driver for Cadence's XSPI controller. It supports 3 work modes. 1. ACMD (auto command) work mode ACMD name is because it uses auto command engine in the controller. It further has 2 modes PIO and CDMA (command DMA). The CDMA work mode is dedicated for high-performance application where very low software overhead is required. In this mode the Command Engine is programmed by the series of linked descriptors stored in system memory. These descriptors provide commands to execute and store status information for finished commands. The PIO mode work mode is dedicated for single operation where constructing a linked list of descriptors would require too much effort. 2. STIG (Software Triggered Instruction Generator) work mode In STIG mode, controller sends low-level instructions to memory. Each instruction is 128-bit width. There is special instruction DataSequence which carries information about data phase. Driver uses Slave DMA interface to transfer data as only this interface can be used in STIG work mode. 3. Direct work mode This work mode allows sending data without invoking any command through the slave interface. Currently only STIG work mode is enabled, remaining work modes will be added later. Signed-off-by: Konrad Kociolek <konrad@cadence.com> Signed-off-by: Jayshri Pawar <jpawar@cadence.com> Signed-off-by: Parshuram Thombare <pthombar@cadence.com> Acked-by: Pratyush Yadav <p.yadav@ti.com> Link: https://lore.kernel.org/r/1632038734-23999-1-git-send-email-pthombar@cadence.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-09-19 10:05:34 +02:00
spi: cadence: add support for Cadence XSPI controller This patch adds driver for Cadence's XSPI controller. It supports 3 work modes. 1. ACMD (auto command) work mode ACMD name is because it uses auto command engine in the controller. It further has 2 modes PIO and CDMA (command DMA). The CDMA work mode is dedicated for high-performance application where very low software overhead is required. In this mode the Command Engine is programmed by the series of linked descriptors stored in system memory. These descriptors provide commands to execute and store status information for finished commands. The PIO mode work mode is dedicated for single operation where constructing a linked list of descriptors would require too much effort. 2. STIG (Software Triggered Instruction Generator) work mode In STIG mode, controller sends low-level instructions to memory. Each instruction is 128-bit width. There is special instruction DataSequence which carries information about data phase. Driver uses Slave DMA interface to transfer data as only this interface can be used in STIG work mode. 3. Direct work mode This work mode allows sending data without invoking any command through the slave interface. Currently only STIG work mode is enabled, remaining work modes will be added later. Signed-off-by: Konrad Kociolek <konrad@cadence.com> Signed-off-by: Jayshri Pawar <jpawar@cadence.com> Signed-off-by: Parshuram Thombare <pthombar@cadence.com> Acked-by: Pratyush Yadav <p.yadav@ti.com> Link: https://lore.kernel.org/r/1632038734-23999-1-git-send-email-pthombar@cadence.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-09-19 10:05:34 +02:00
spi: cadence: add support for Cadence XSPI controller This patch adds driver for Cadence's XSPI controller. It supports 3 work modes. 1. ACMD (auto command) work mode ACMD name is because it uses auto command engine in the controller. It further has 2 modes PIO and CDMA (command DMA). The CDMA work mode is dedicated for high-performance application where very low software overhead is required. In this mode the Command Engine is programmed by the series of linked descriptors stored in system memory. These descriptors provide commands to execute and store status information for finished commands. The PIO mode work mode is dedicated for single operation where constructing a linked list of descriptors would require too much effort. 2. STIG (Software Triggered Instruction Generator) work mode In STIG mode, controller sends low-level instructions to memory. Each instruction is 128-bit width. There is special instruction DataSequence which carries information about data phase. Driver uses Slave DMA interface to transfer data as only this interface can be used in STIG work mode. 3. Direct work mode This work mode allows sending data without invoking any command through the slave interface. Currently only STIG work mode is enabled, remaining work modes will be added later. Signed-off-by: Konrad Kociolek <konrad@cadence.com> Signed-off-by: Jayshri Pawar <jpawar@cadence.com> Signed-off-by: Parshuram Thombare <pthombar@cadence.com> Acked-by: Pratyush Yadav <p.yadav@ti.com> Link: https://lore.kernel.org/r/1632038734-23999-1-git-send-email-pthombar@cadence.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-09-19 10:05:34 +02:00
spi: dw: Add memory operations support Aside from the synchronous Tx-Rx mode, which has been utilized to create the normal SPI transfers in the framework of the DW SSI driver, DW SPI controller supports Tx-only and EEPROM-read modes. The former one just enables the controller to transmit all the data from the Tx FIFO ignoring anything retrieved from the MISO lane. The later mode is so called write-then-read operation: DW SPI controller first pushes out all the data from the Tx FIFO, after that it'll automatically receive as much data as has been specified by means of the CTRLR1 register. Both of those modes can be used to implement the memory operations supported by the SPI-memory subsystem. The memory operation implementation is pretty much straightforward, except a few peculiarities we have had to take into account to make things working. Since DW SPI controller doesn't provide a way to directly set and clear the native CS lane level, but instead automatically de-asserts it when a transfer going on, we have to make sure the Tx FIFO isn't empty during entire Tx procedure. In addition we also need to read data from the Rx FIFO as fast as possible to prevent it' overflow with automatically fetched incoming traffic. The denoted peculiarities get to cause even more problems if DW SSI controller is equipped with relatively small FIFO and is connected to a relatively slow system bus (APB) (with respect to the SPI bus speed). In order to workaround the problems for as much as it's possible, the memory operation execution procedure collects all the Tx data into a single buffer and disables the local IRQs to speed the write-then-optionally-read method up. Note the provided memory operations are utilized by default only if a glue driver hasn't provided a custom version of ones and this is not a DW APB SSI controller with fixed automatic CS toggle functionality. Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Link: https://lore.kernel.org/r/20201007235511.4935-18-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
2020-10-08 02:55:06 +03:00
spi: dw: Move Non-DMA code to the DW PCIe-SPI driver This is a preparation patch before adding the DW DMA support into the DW SPI MMIO driver. We need to unpin the Non-DMA-specific code from the intended to be generic DW APB SSI DMA code. This isn't that hard, since the most part of the spi-dw-mid.c driver in fact implements a generic DMA interface for the DW SPI controller driver. The only Intel MID specifics concern getting the max frequency from the MRST Clock Control Unit and fetching the DMA controller channels from corresponding PCIe DMA controller. Since first one is related with the SPI interface configuration we moved it' implementation into the DW PCIe-SPI driver module. After that former spi-dw-mid.c file can be just renamed to be the DW SPI DMA module optionally compiled in to the DW APB SSI core driver. Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Feng Tang <feng.tang@intel.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Link: https://lore.kernel.org/r/20200529131205.31838-11-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-29 16:11:59 +03:00
spi: add driver for NXP XSPI controller Add driver support for NXP XSPI controller. XSPI is a flexible SPI host controller which supports up to 2 external devices (2 CS). It support Single/Dual/Quad/Octal mode data transfer. The difference between XSPI and Flexspi: 1.the register layout is total different. 2.XSPI support multiple independent execution environments (EENVs) for HW virtualization with some limitations. Each EENV has its own interrupt and its own set of programming registers that exists in a specific offset range in the XSPI memory map. The main environment (EENV0) address space contains all of the registers for controlling EENV0 plus all of the general XSPI control and programming registers. The register mnemonics for the user environments (EENV1 to EENV4) have "_SUB_n" appended to the mnemonic for the corresponding main-environment register. Current driver based on EENV0, which means system already give EENV0 right to linux. This driver use SPI memory interface of the SPI framework to issue flash memory operations. Tested this driver with UBIFS and mtd_debug on NXP i.MX943 EVK board which has one spi nor MT35XU512ABA flash. Now this driver has the following key features: - Support up to OCT DDR mode - Support AHB read - Support IP read and IP write - Support two CS Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Link: https://patch.msgid.link/20251216-xspi-v7-2-282525220979@nxp.com Signed-off-by: Mark Brown <broonie@kernel.org>
2025-12-16 11:20:14 +08:00
spi/fsl_spi: add eSPI controller support Add eSPI controller support based on the library code spi_fsl_lib.c. The eSPI controller is newer controller 85xx/Pxxx devices supported. There're some differences comparing to the SPI controller: 1. Has different register map and different bit definition So leave the code operated the register to the driver code, not the common code. 2. Support 4 dedicated chip selects The software can't controll the chip selects directly, The SPCOM[CS] field is used to select which chip selects is used, and the SPCOM[TRANLEN] field is set to tell the controller how long the CS signal need to be asserted. So the driver doesn't need the chipselect related function when transfering data, just set corresponding register fields to controll the chipseclect. 3. Different Transmit/Receive FIFO access register behavior For SPI controller, the Tx/Rx FIFO access register can hold only one character regardless of the character length, but for eSPI controller, the register can hold 4 or 2 characters according to the character lengths. Access the Tx/Rx FIFO access register of the eSPI controller will shift out/in 4/2 characters one time. For SPI subsystem, the command and data are put into different transfers, so we need to combine all the transfers to one transfer in order to pass the transfer to eSPI controller. 4. The max transaction length limitation The max transaction length one time is limitted by the SPCOM[TRANSLEN] field which is 0xFFFF. When used mkfs.ext2 command to create ext2 filesystem on the flash, the read length will exceed the max value of the SPCOM[TRANSLEN] field. Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-10-12 18:18:32 +08:00
spi/fsl_spi: add eSPI controller support Add eSPI controller support based on the library code spi_fsl_lib.c. The eSPI controller is newer controller 85xx/Pxxx devices supported. There're some differences comparing to the SPI controller: 1. Has different register map and different bit definition So leave the code operated the register to the driver code, not the common code. 2. Support 4 dedicated chip selects The software can't controll the chip selects directly, The SPCOM[CS] field is used to select which chip selects is used, and the SPCOM[TRANLEN] field is set to tell the controller how long the CS signal need to be asserted. So the driver doesn't need the chipselect related function when transfering data, just set corresponding register fields to controll the chipseclect. 3. Different Transmit/Receive FIFO access register behavior For SPI controller, the Tx/Rx FIFO access register can hold only one character regardless of the character length, but for eSPI controller, the register can hold 4 or 2 characters according to the character lengths. Access the Tx/Rx FIFO access register of the eSPI controller will shift out/in 4/2 characters one time. For SPI subsystem, the command and data are put into different transfers, so we need to combine all the transfers to one transfer in order to pass the transfer to eSPI controller. 4. The max transaction length limitation The max transaction length one time is limitted by the SPCOM[TRANSLEN] field which is 0xFFFF. When used mkfs.ext2 command to create ext2 filesystem on the flash, the read length will exceed the max value of the SPCOM[TRANSLEN] field. Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-10-12 18:18:32 +08:00
spi: add support for mediatek spi-nor controller This is a driver for mtk spi-nor controller using spi-mem interface. The same controller already has limited support provided by mtk-quadspi driver under spi-nor framework and this new driver is a replacement for the old one. Comparing to the old driver, this driver has following advantages: 1. It can handle any full-duplex spi transfer up to 6 bytes, and this is implemented using generic spi interface. 2. It take account into command opcode properly. The reading routine in this controller can only use 0x03 or 0x0b as opcode on 1-1-1 transfers, but old driver doesn't implement this properly. This driver checks supported opcode explicitly and use (1) to perform unmatched operations. 3. It properly handles SFDP reading. Old driver can't read SFDP due to the bug mentioned in (2). 4. It can do 1-2-2 and 1-4-4 fast reading on spi-nor. These two ops requires parsing SFDP, which isn't possible in old driver. And the old driver is only flagged to support 1-1-2 mode. 5. It takes advantage of the DMA feature in this controller for long reads and supports IRQ on DMA requests to free cpu cycles from polling status registers on long DMA reading. It achieves up to 17.5MB/s reading speed (1-4-4 mode) which is way faster than the old one. IRQ is implemented as optional to maintain backward compatibility. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> Link: https://lore.kernel.org/r/20200306085052.28258-3-gch981213@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-03-06 16:50:50 +08:00
spi: add support for mediatek spi-nor controller This is a driver for mtk spi-nor controller using spi-mem interface. The same controller already has limited support provided by mtk-quadspi driver under spi-nor framework and this new driver is a replacement for the old one. Comparing to the old driver, this driver has following advantages: 1. It can handle any full-duplex spi transfer up to 6 bytes, and this is implemented using generic spi interface. 2. It take account into command opcode properly. The reading routine in this controller can only use 0x03 or 0x0b as opcode on 1-1-1 transfers, but old driver doesn't implement this properly. This driver checks supported opcode explicitly and use (1) to perform unmatched operations. 3. It properly handles SFDP reading. Old driver can't read SFDP due to the bug mentioned in (2). 4. It can do 1-2-2 and 1-4-4 fast reading on spi-nor. These two ops requires parsing SFDP, which isn't possible in old driver. And the old driver is only flagged to support 1-1-2 mode. 5. It takes advantage of the DMA feature in this controller for long reads and supports IRQ on DMA requests to free cpu cycles from polling status registers on long DMA reading. It achieves up to 17.5MB/s reading speed (1-4-4 mode) which is way faster than the old one. IRQ is implemented as optional to maintain backward compatibility. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> Link: https://lore.kernel.org/r/20200306085052.28258-3-gch981213@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-03-06 16:50:50 +08:00
spi: add support for mediatek spi-nor controller This is a driver for mtk spi-nor controller using spi-mem interface. The same controller already has limited support provided by mtk-quadspi driver under spi-nor framework and this new driver is a replacement for the old one. Comparing to the old driver, this driver has following advantages: 1. It can handle any full-duplex spi transfer up to 6 bytes, and this is implemented using generic spi interface. 2. It take account into command opcode properly. The reading routine in this controller can only use 0x03 or 0x0b as opcode on 1-1-1 transfers, but old driver doesn't implement this properly. This driver checks supported opcode explicitly and use (1) to perform unmatched operations. 3. It properly handles SFDP reading. Old driver can't read SFDP due to the bug mentioned in (2). 4. It can do 1-2-2 and 1-4-4 fast reading on spi-nor. These two ops requires parsing SFDP, which isn't possible in old driver. And the old driver is only flagged to support 1-1-2 mode. 5. It takes advantage of the DMA feature in this controller for long reads and supports IRQ on DMA requests to free cpu cycles from polling status registers on long DMA reading. It achieves up to 17.5MB/s reading speed (1-4-4 mode) which is way faster than the old one. IRQ is implemented as optional to maintain backward compatibility. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> Link: https://lore.kernel.org/r/20200306085052.28258-3-gch981213@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-03-06 16:50:50 +08:00
spi: fix building SPI_PXA on MMP When the audio driver selects CONFIG_PXA_SSP on ARCH_MMP as a loadable module, and the PXA SPI driver is built-in, we get a link error in the SPI driver: drivers/spi/spi-pxa2xx.o: In function `pxa2xx_spi_remove': spi-pxa2xx.c:(.text+0x5f0): undefined reference to `pxa_ssp_free' drivers/spi/spi-pxa2xx.o: In function `pxa2xx_spi_probe': spi-pxa2xx.c:(.text+0xeac): undefined reference to `pxa_ssp_request' spi-pxa2xx.c:(.text+0x1468): undefined reference to `pxa_ssp_free' spi-pxa2xx.c:(.text+0x15bc): undefined reference to `pxa_ssp_free' The problem is that the PXA SPI driver only uses 'select SSP' specifically when building it for PXA, but we can also build it for PCI, which is meant for Intel x86 SoCs that use the same SPI block. When the sound driver forces the SSP to be a loadable module, the IS_ENABLED() check in include/linux/pxa2xx_ssp.h triggers but the spi driver can't reference the exported symbols. I had a different approach before, making the PCI case depend on X86, which fixed the problem by avoiding the MMP case. This goes a different route, making the driver select PXA_SSP also on MMP, which has an SSP that none of the boards in mainline Linux use for SPI. There is no harm in always enabling the build on MMP (PCI or not PCI), so I do that too, to document that this hardware is actually available on MMP. Link: https://patchwork.kernel.org/patch/8879921/ Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Mark Brown <broonie@kernel.org>
2017-08-07 17:42:55 +02:00
spi/rockchip: add driver for Rockchip RK3xxx SoCs integrated SPI In order to facilitate understanding, rockchip SPI controller IP design looks similar in its registers to designware. But IC implementation is different from designware, So we need a dedicated driver for Rockchip RK3XXX SoCs integrated SPI. The main differences: - dma request line: rockchip SPI controller have two DMA request line for tx and rx. - Register offset: RK3288 dw SPI_CTRLR0 0x0000 0x0000 SPI_CTRLR1 0x0004 0x0004 SPI_SSIENR 0x0008 0x0008 SPI_MWCR NONE 0x000c SPI_SER 0x000c 0x0010 SPI_BAUDR 0x0010 0x0014 SPI_TXFTLR 0x0014 0x0018 SPI_RXFTLR 0x0018 0x001c SPI_TXFLR 0x001c 0x0020 SPI_RXFLR 0x0020 0x0024 SPI_SR 0x0024 0x0028 SPI_IPR 0x0028 NONE SPI_IMR 0x002c 0x002c SPI_ISR 0x0030 0x0030 SPI_RISR 0x0034 0x0034 SPI_TXOICR NONE 0x0038 SPI_RXOICR NONE 0x003c SPI_RXUICR NONE 0x0040 SPI_MSTICR NONE 0x0044 SPI_ICR 0x0038 0x0048 SPI_DMACR 0x003c 0x004c SPI_DMATDLR 0x0040 0x0050 SPI_DMARDLR 0x0044 0x0054 SPI_TXDR 0x0400 NONE SPI_RXDR 0x0800 NONE SPI_IDR NONE 0x0058 SPI_VERSION NONE 0x005c SPI_DR NONE 0x0060 - register configuration: such as SPI_CTRLRO in rockchip SPI controller: cr0 = (CR0_BHT_8BIT << CR0_BHT_OFFSET) | (CR0_SSD_ONE << CR0_SSD_OFFSET); cr0 |= (rs->n_bytes << CR0_DFS_OFFSET); cr0 |= ((rs->mode & 0x3) << CR0_SCPH_OFFSET); cr0 |= (rs->tmode << CR0_XFM_OFFSET); cr0 |= (rs->type << CR0_FRF_OFFSET); For more information, see RK3288 chip manual. - Wait for idle: Must ensure that the FIFO data has been sent out before the next transfer. Signed-off-by: addy ke <addy.ke@rock-chips.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-01 09:03:59 +08:00
spi/rockchip: add driver for Rockchip RK3xxx SoCs integrated SPI In order to facilitate understanding, rockchip SPI controller IP design looks similar in its registers to designware. But IC implementation is different from designware, So we need a dedicated driver for Rockchip RK3XXX SoCs integrated SPI. The main differences: - dma request line: rockchip SPI controller have two DMA request line for tx and rx. - Register offset: RK3288 dw SPI_CTRLR0 0x0000 0x0000 SPI_CTRLR1 0x0004 0x0004 SPI_SSIENR 0x0008 0x0008 SPI_MWCR NONE 0x000c SPI_SER 0x000c 0x0010 SPI_BAUDR 0x0010 0x0014 SPI_TXFTLR 0x0014 0x0018 SPI_RXFTLR 0x0018 0x001c SPI_TXFLR 0x001c 0x0020 SPI_RXFLR 0x0020 0x0024 SPI_SR 0x0024 0x0028 SPI_IPR 0x0028 NONE SPI_IMR 0x002c 0x002c SPI_ISR 0x0030 0x0030 SPI_RISR 0x0034 0x0034 SPI_TXOICR NONE 0x0038 SPI_RXOICR NONE 0x003c SPI_RXUICR NONE 0x0040 SPI_MSTICR NONE 0x0044 SPI_ICR 0x0038 0x0048 SPI_DMACR 0x003c 0x004c SPI_DMATDLR 0x0040 0x0050 SPI_DMARDLR 0x0044 0x0054 SPI_TXDR 0x0400 NONE SPI_RXDR 0x0800 NONE SPI_IDR NONE 0x0058 SPI_VERSION NONE 0x005c SPI_DR NONE 0x0060 - register configuration: such as SPI_CTRLRO in rockchip SPI controller: cr0 = (CR0_BHT_8BIT << CR0_BHT_OFFSET) | (CR0_SSD_ONE << CR0_SSD_OFFSET); cr0 |= (rs->n_bytes << CR0_DFS_OFFSET); cr0 |= ((rs->mode & 0x3) << CR0_SCPH_OFFSET); cr0 |= (rs->tmode << CR0_XFM_OFFSET); cr0 |= (rs->type << CR0_FRF_OFFSET); For more information, see RK3288 chip manual. - Wait for idle: Must ensure that the FIFO data has been sent out before the next transfer. Signed-off-by: addy ke <addy.ke@rock-chips.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-01 09:03:59 +08:00
[PATCH] spi: simple SPI framework This is the core of a small SPI framework, implementing the model of a queue of messages which complete asynchronously (with thin synchronous wrappers on top). - It's still less than 2KB of ".text" (ARM). If there's got to be a mid-layer for something so simple, that's the right size budget. :) - The guts use board-specific SPI device tables to build the driver model tree. (Hardware probing is rarely an option.) - This version of Kconfig includes no drivers. At this writing there are two known master controller drivers (PXA/SSP, OMAP MicroWire) and three protocol drivers (CS8415a, ADS7846, DataFlash) with LKML mentions of other drivers in development. - No userspace API. There are several implementations to compare. Implement them like any other driver, and bind them with sysfs. The changes from last version posted to LKML (on 11-Nov-2005) are minor, and include: - One bugfix (removes a FIXME), with the visible effect of making device names be "spiB.C" where B is the bus number and C is the chipselect. - The "caller provides DMA mappings" mechanism now has kerneldoc, for DMA drivers that want to be fancy. - Hey, the framework init can be subsys_init. Even though board init logic fires earlier, at arch_init ... since the framework init is for driver support, and the board init support uses static init. - Various additional spec/doc clarifications based on discussions with other folk. It adds a brief "thank you" at the end, for folk who've helped nudge this framework into existence. As I've said before, I think that "protocol tweaking" is the main support that this driver framework will need to evolve. From: Mark Underwood <basicmark@yahoo.com> Update the SPI framework to remove a potential priority inversion case by reverting to kmalloc if the pre-allocated DMA-safe buffer isn't available. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-08 13:34:19 -08:00
[PATCH] spi: simple SPI framework This is the core of a small SPI framework, implementing the model of a queue of messages which complete asynchronously (with thin synchronous wrappers on top). - It's still less than 2KB of ".text" (ARM). If there's got to be a mid-layer for something so simple, that's the right size budget. :) - The guts use board-specific SPI device tables to build the driver model tree. (Hardware probing is rarely an option.) - This version of Kconfig includes no drivers. At this writing there are two known master controller drivers (PXA/SSP, OMAP MicroWire) and three protocol drivers (CS8415a, ADS7846, DataFlash) with LKML mentions of other drivers in development. - No userspace API. There are several implementations to compare. Implement them like any other driver, and bind them with sysfs. The changes from last version posted to LKML (on 11-Nov-2005) are minor, and include: - One bugfix (removes a FIXME), with the visible effect of making device names be "spiB.C" where B is the bus number and C is the chipselect. - The "caller provides DMA mappings" mechanism now has kerneldoc, for DMA drivers that want to be fancy. - Hey, the framework init can be subsys_init. Even though board init logic fires earlier, at arch_init ... since the framework init is for driver support, and the board init support uses static init. - Various additional spec/doc clarifications based on discussions with other folk. It adds a brief "thank you" at the end, for folk who've helped nudge this framework into existence. As I've said before, I think that "protocol tweaking" is the main support that this driver framework will need to evolve. From: Mark Underwood <basicmark@yahoo.com> Update the SPI framework to remove a potential priority inversion case by reverting to kmalloc if the pre-allocated DMA-safe buffer isn't available. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-08 13:34:19 -08:00
[PATCH] spi: simple SPI framework This is the core of a small SPI framework, implementing the model of a queue of messages which complete asynchronously (with thin synchronous wrappers on top). - It's still less than 2KB of ".text" (ARM). If there's got to be a mid-layer for something so simple, that's the right size budget. :) - The guts use board-specific SPI device tables to build the driver model tree. (Hardware probing is rarely an option.) - This version of Kconfig includes no drivers. At this writing there are two known master controller drivers (PXA/SSP, OMAP MicroWire) and three protocol drivers (CS8415a, ADS7846, DataFlash) with LKML mentions of other drivers in development. - No userspace API. There are several implementations to compare. Implement them like any other driver, and bind them with sysfs. The changes from last version posted to LKML (on 11-Nov-2005) are minor, and include: - One bugfix (removes a FIXME), with the visible effect of making device names be "spiB.C" where B is the bus number and C is the chipselect. - The "caller provides DMA mappings" mechanism now has kerneldoc, for DMA drivers that want to be fancy. - Hey, the framework init can be subsys_init. Even though board init logic fires earlier, at arch_init ... since the framework init is for driver support, and the board init support uses static init. - Various additional spec/doc clarifications based on discussions with other folk. It adds a brief "thank you" at the end, for folk who've helped nudge this framework into existence. As I've said before, I think that "protocol tweaking" is the main support that this driver framework will need to evolve. From: Mark Underwood <basicmark@yahoo.com> Update the SPI framework to remove a potential priority inversion case by reverting to kmalloc if the pre-allocated DMA-safe buffer isn't available. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-08 13:34:19 -08:00
[PATCH] spi: simple SPI framework This is the core of a small SPI framework, implementing the model of a queue of messages which complete asynchronously (with thin synchronous wrappers on top). - It's still less than 2KB of ".text" (ARM). If there's got to be a mid-layer for something so simple, that's the right size budget. :) - The guts use board-specific SPI device tables to build the driver model tree. (Hardware probing is rarely an option.) - This version of Kconfig includes no drivers. At this writing there are two known master controller drivers (PXA/SSP, OMAP MicroWire) and three protocol drivers (CS8415a, ADS7846, DataFlash) with LKML mentions of other drivers in development. - No userspace API. There are several implementations to compare. Implement them like any other driver, and bind them with sysfs. The changes from last version posted to LKML (on 11-Nov-2005) are minor, and include: - One bugfix (removes a FIXME), with the visible effect of making device names be "spiB.C" where B is the bus number and C is the chipselect. - The "caller provides DMA mappings" mechanism now has kerneldoc, for DMA drivers that want to be fancy. - Hey, the framework init can be subsys_init. Even though board init logic fires earlier, at arch_init ... since the framework init is for driver support, and the board init support uses static init. - Various additional spec/doc clarifications based on discussions with other folk. It adds a brief "thank you" at the end, for folk who've helped nudge this framework into existence. As I've said before, I think that "protocol tweaking" is the main support that this driver framework will need to evolve. From: Mark Underwood <basicmark@yahoo.com> Update the SPI framework to remove a potential priority inversion case by reverting to kmalloc if the pre-allocated DMA-safe buffer isn't available. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-01-08 13:34:19 -08:00