The i.MX6SX LCDIF is not fully compatible with the i.MX28 LCDIF. The
i.MX6SX controller provides additional overlay registers (AS_CTRL) which
are not present on i.MX28.
Linux has supported the dedicated compatible string since commit
45d59d7040 ("drm: Add new driver for MXSFB controller").
Other known DT users such as U-Boot and Barebox already support
"fsl,imx6sx-lcdif", so removing the fallback compatible string is low risk
since this device is used for display output only.
Fix the following CHECK_DTB warning:
/arch/arm/boot/dts/nxp/imx/imx6sx-nitrogen6sx.dtb: lcdif@2220000 (fsl,imx6sx-lcdif): compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx6sx-lcdif', 'fsl,imx28-lcdif'] is too long
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Rename node name tcq to touchscreen to fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx25-karo-tx25.dtb: tscadc@50030000 (fsl,imx25-tsadc): 'tcq@50030400' does not match any of the regexes: '^adc@[0-9a-f]+$', '^pinctrl-[0-9]+$', '^touchscreen@[0-9a-f]+$'
from schema $id: http://devicetree.org/schemas/mfd/fsl,imx25-tsadc.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Disable the unused interface, to fix print an error message during boot:
mmc3: Failed to initialize a non-removable card
Signed-off-by: Ian Ray <ian.ray@gehealthcare.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Set `phy-mode' on network switch CPU ports to eliminate a warning:
mv88e6085 gpio-0:00: OF node /mdio-gpio/switch@0/ports/port@4 of CPU port 4 lacks the required "phy-mode" property
Signed-off-by: Ian Ray <ian.ray@gehealthcare.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Configure maximum speed for the switch PHYs according to the electrical
connections from PHY to RJ45 connector.
Signed-off-by: Ian Ray <ian.ray@gehealthcare.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add missing CPU clock definitions and operating-points-v2 table for the
Cortex-A7 on i.MX7ULP to enable proper CPU frequency scaling and
integration with the cpufreq/OPP frameworks.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Deassert BOOT_EN after boot to separate BOOT_CFG
circuits from LCD signals.
Signed-off-by: Alexander Feilke <Alexander.Feilke@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
dtschema/schemas/bootph.yaml describe various node usage during
boot phases with DT.
Adds boot phase properties to essential resources in
tqma7 device trees. This includes UART, SD-Card, eMMC and QSPI.
Signed-off-by: Alexander Feilke <Alexander.Feilke@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
dtschema/schemas/bootph.yaml describe various node usage during
boot phases with DT.
Adds boot phase properties to essential resources in imx7s device trees.
This includes the buses aips1-3, iomuxc and SOC access.
Signed-off-by: Alexander Feilke <Alexander.Feilke@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
TQ-Systems is written with a hyphen. Correct the spelling.
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
dtschema/schemas/bootph.yaml describe various node usage during
boot phases with DT.
MBa6ULx need regulator, SD-Card, UART and watchdog access during
boot process.
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
dtschema/schemas/bootph.yaml describe various node usage during
boot phases with DT.
TQMa6UL need eMMC, I2C, GPIO and QSPI access during boot process.
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
dtschema/schemas/bootph.yaml describe various node usage during
boot phases with DT.
All SoCs require buses (aips and spba), clock, iomuxc and SOC access
during boot process.
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
dtschema/schemas/bootph.yaml describe various node usage during
boot phases with DT.
MBa6 need I2C, GPIO, SD-Card, UART and watchdog access during
boot process.
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
dtschema/schemas/bootph.yaml describe various node usage during
boot phases with DT.
TQMa6 need eMMC, I2C, GPIO, regulator and QSPI access during
boot process.
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
dtschema/schemas/bootph.yaml describe various node usage during
boot phases with DT.
All SoCs require buses (aips and spba), clock, iomuxc, ipu and
SOC access during boot process.
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the missing labels for the temperature sensor and the EEPROM.
In SoM variants A and B, the components are connected to different
I2C buses. These labels are needed to reference them in subsequent
device trees.
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add required clocks and clock-names for ccm to fix below CHECK_DTBS
warnings:
arch/arm/boot/dts/nxp/imx/imx6dl-alti6p.dtb: clock-controller@20c4000 (fsl,imx6q-ccm): clock-names:0: 'osc' was expected
from schema $id: http://devicetree.org/schemas/clock/imx6q-clock.yaml#
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add label for system clocks and add two missing clocks anaclk[1,2]. Prepare
for fixing ccm related CHECK_DTB warnings.
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Remove undocumented aliases, which is not used in kernel to fix
CHECK_DTBS warnings.
arch/arm/boot/dts/nxp/mxs/imx28-tx28.dtb: aliases: 'lcdif_23bit_pins', 'lcdif_24bit_pins', 'reg_can_xcvr', 'spi_gpio', 'spi_mxs' do not match any of the regexes: '^[a-z][a-z0-9\\-]*$', '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/aliases.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The compatible string "edt,edt-ft5x06" is neither documented nor used.
According to drivers/input/touchscreen/edt-ft5x06.c, ft5206, ft5306 and
ft5406 are compatible.
Use "edt,edt-ft5206" instead, as the datasheet does not specify the
exact touchscreen model.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Remove the undocumented fallback compatible string "mr25h256", as the
SPI core strips the vendor prefix.
Fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/mxs/imx28-sps1.dtb: /apb@80000000/apbh-bus@80000000/spi@80014000/flash@0: failed to match any schema with compatible: ['everspin,mr25h256', 'mr25h256']
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Rename gpios-reset to reset-gpios of hx8357 node to fix below CHECK_DTBS
warnings:
arch/arm/boot/dts/nxp/mxs/imx28-cfa10055.dtb: hx8357@0 (himax,hx8357b): Unevaluated properties are not allowed ('gpios-reset' was unexpected)
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the "led-" prefix to LED subnodes to fix the below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/mxs/imx23-olinuxino.dtb: leds (gpio-leds): 'user' does not match any of the regexes: '(^led-[0-9a-f]$|led)', '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
There are duplicate "empty" entries in the interrupt-names property of
the DMA controller. Rename them to "empty<n>" to fix below CHECK_DTBS
warnings.
arch/arm/boot/dts/nxp/mxs/imx23-olinuxino.dtb: dma-controller@80024000 (fsl,imx23-dma-apbx): interrupt-names:15: 'empty5' was expected
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Remove fsl,imx-osc26m from fixed-clock node to fix below CHECK_DTB
warnings:
arch/arm/boot/dts/nxp/imx/imx27-apf27.dtb: osc26m (fsl,imx-osc26m): compatible: ['fsl,imx-osc26m', 'fixed-clock'] is too long
from schema $id: http://devicetree.org/schemas/clock/fixed-clock.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Rename node name uart8250 to serial to fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx27-eukrea-mbimxsd27-baseboard.dtb: uart8250@3,200000 (ns8250): $nodename:0: 'uart8250@3,200000' does not match '^serial(@.*)?$'
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The property interrupts use default interrupt controllers. But pass down
gpio<n> as phandle. Correct it by use interrupts-extended.
Fixes: d8cae888aa ("ARM: dts: Add support for the cpuimx27 board from Eukrea and its baseboard")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Remove the redundant intermediate node between the pinmux and group nodes,
and add the missing "grp" suffix to the group node names.
Fix below CHECK_DTBS warnings:
arm/boot/dts/nxp/imx/imx27-apf27dev.dtb: iomuxc@10015000 (fsl,imx27-iomuxc): Unevaluated properties are not allowed ('imx27-apf27', 'imx27-apf27dev' were unexpected)
from schema $id: http://devicetree.org/schemas/pinctrl/fsl,imx27-iomuxc.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Rename node name iomuxc to pinmux. Fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx1-apf9328.dtb: iomuxc@21c000 (fsl,imx1-iomuxc): $nodename:0: 'iomuxc@21c000' does not match '^(pinctrl|pinmux)(@[0-9a-f]+)?$'
from schema $id: http://devicetree.org/schemas/pinctrl/fsl,imx27-iomuxc.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The muRata 1DX WiFi/BT chip is mounted on the DHCOM i.MX6ULL. This chip
has been discontinued and replaced by the muRata 1YN chip. The new chip
is a drop-in replacement of the old chip. To support both chips for the
i.MX6ULL DHCOR, drop the more specific compatible string and let the
driver auto-detect the chip type. Currently, there are no known quirks
that would apply only to one or the other chip.
Signed-off-by: Marek Vasut <marex@nabladev.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The ov2680 only support 1 lane. Needn't additional property to descript it.
Remove it to fix below DTB_CHECK warnings:
camera@36 (ovti,ov2680): port:endpoint: 'clock-lanes', 'data-lanes' do not match any of the regexes: '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/media/i2c/ovti,ov2680.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add power supply, #sound-dai-cells and clock nodes for fsl,sgtl5000 to
fix below CHECK_DTB warnings:
arch/arm/boot/dts/nxp/imx/imx53-smd.dtb: sgtl5000@a (fsl,sgtl5000): '#sound-dai-cells' is a required property
from schema $id: http://devicetree.org/schemas/sound/fsl,sgtl5000.yaml#
arch/arm/boot/dts/nxp/imx/imx53-smd.dtb: sgtl5000@a (fsl,sgtl5000): 'clocks' is a required property
from schema $id: http://devicetree.org/schemas/sound/fsl,sgtl5000.yaml#
arch/arm/boot/dts/nxp/imx/imx53-smd.dtb: sgtl5000@a (fsl,sgtl5000): 'VDDA-supply' is a required property
from schema $id: http://devicetree.org/schemas/sound/fsl,sgtl5000.yaml#
arch/arm/boot/dts/nxp/imx/imx53-smd.dtb: sgtl5000@a (fsl,sgtl5000): 'VDDIO-supply' is a required property
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Replace the clock-frequency property with a fixed-clock providing the
32kHz input to the gpio-gate-clock.
Fix the following CHECK_DTBS warning:
ti-wifi-clock (gpio-gate-clock): 'clock-frequency' does not match any of the regexes: '^pinctrl-[0-9]+$'
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Rename at45db321d@1 to flash@1 to fix below CHECK_DTBS warnings:
at45db321d@1 (atmel,at45db321d): $nodename:0: 'at45db321d@1' does not match '^(flash|.*sram|nand)(@.*)?$'
from schema $id: http://devicetree.org/schemas/mtd/atmel,dataflash.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Change node name fpga@0 to fpga@0,0 to fix below CHECK_DTBS warnings:
memory-controller@83fda000 (fsl,imx51-weim): 'fpga@0' does not match any of the regexes: '^.*@[0-7],[0-9a-f]+$', '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/memory-controllers/fsl/fsl,imx-weim.yam
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Remove simple bus 'usbphy' and move chip nodes to up layers to fix below
CHECK_DTBS warnings.
arch/arm/boot/dts/nxp/imx/imx35-pdk.dtb: usbphy (simple-bus): usb-phy@1:reg:0: [1] is too short
from schema $id: http://devicetree.org/schemas/simple-bus.yaml
Remove property 'reg' because it is never used at driver.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Rename the i2c clock-names from "ipg_per" to "ipg" to match the binding
documentation.
Fix the following CHECK_DTBS warning:
i2c@43f80000 (fsl,imx35-i2c): clock-names:0: 'ipg' was expected
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Rename emi to emi-bus to fix below CHECK_DTBS warning:
arch/arm/boot/dts/nxp/imx/imx31-bug.dtb: emi@b8000000 (simple-bus): $nodename:0: 'emi@b8000000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
from schema $id: http://devicetree.org/schemas/simple-bus.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
This way the detected signal is valid only if it lasts longer than
62 µs, otherwise it is not sampled.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
- Fix a build error on parisc
- Remove the non-large-folio-aware function fsverity_verify_page()
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQSacvsUNc7UX4ntmEPzXCl4vpKOKwUCaZtg+xQcZWJpZ2dlcnNA
a2VybmVsLm9yZwAKCRDzXCl4vpKOKwQ+AQCiXEYAibl3vHRgQo7qEPCC5or4FtkF
HZ0ERRArhsU17AD/TKHE/AJkyFrwK4rGTb6I9Wi1OXnpG7jihZlYjj03Ag4=
=CUql
-----END PGP SIGNATURE-----
Merge tag 'fsverity-for-linus' of git://git.kernel.org/pub/scm/fs/fsverity/linux
Pull fsverity fixes from Eric Biggers:
- Fix a build error on parisc
- Remove the non-large-folio-aware function fsverity_verify_page()
* tag 'fsverity-for-linus' of git://git.kernel.org/pub/scm/fs/fsverity/linux:
fsverity: fix build error by adding fsverity_readahead() stub
fsverity: remove fsverity_verify_page()
f2fs: make f2fs_verify_cluster() partially large-folio-aware
f2fs: remove unnecessary ClearPageUptodate in f2fs_verify_cluster()
Fix a big endian specific issue in the PPC64-optimized AES code.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQSacvsUNc7UX4ntmEPzXCl4vpKOKwUCaZtiphQcZWJpZ2dlcnNA
a2VybmVsLm9yZwAKCRDzXCl4vpKOK/z2AQD1j15Ao3iDW3yBSyTS+tFJaRUVDtjg
bNostoNJAjMM9wD/X0oAnt95WTNkdHexs+2aMzQ4ULKFRcwQrUTarKx7IgY=
=Dmfx
-----END PGP SIGNATURE-----
Merge tag 'libcrypto-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull crypto library fix from Eric Biggers:
"Fix a big endian specific issue in the PPC64-optimized AES code"
* tag 'libcrypto-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux:
lib/crypto: powerpc/aes: Fix rndkey_from_vsx() on big endian CPUs
Stephen retired and stepped back from -next maintainership, update his
entry in CREDITS to recognise his 18 years of hard work making it what
it is today and all the impact it's had on our development process.
Also update to his current GnuPG key while we're here.
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: SeongJae Park <sj@kernel.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The x509 public key code gained a dependency on the sha256 hash
implementation, causing a rare link time failure in randconfig
builds:
arm-linux-gnueabi-ld: crypto/asymmetric_keys/x509_public_key.o: in function `x509_get_sig_params':
x509_public_key.c:(.text.x509_get_sig_params+0x12): undefined reference to `sha256'
arm-linux-gnueabi-ld: (sha256): Unknown destination type (ARM/Thumb) in crypto/asymmetric_keys/x509_public_key.o
x509_public_key.c:(.text.x509_get_sig_params+0x12): dangerous relocation: unsupported relocation
Select the necessary library code from Kconfig.
Fixes: 2c62068ac8 ("x509: Separately calculate sha256 for blacklist")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Align to the commit bf4afc53b7 ("Convert 'alloc_obj' family to use the
new default GFP_KERNEL argument") update the 'kmalloc_obj' declaration
for userspace to fix below compile error:
In file included from arch/arm/boot/compressed/../../../../lib/decompress_unxz.c:241,
from arch/arm/boot/compressed/decompress.c:56:
arch/arm/boot/compressed/../../../../lib/xz/xz_dec_stream.c: In function 'xz_dec_init':
arch/arm/boot/compressed/../../../../lib/xz/xz_dec_stream.c:787:28: error: implicit declaration of function 'kmalloc_obj'; did you mean 'kmalloc'? [-Wimplicit-function-declaration]
787 | struct xz_dec *s = kmalloc_obj(*s);
| ^~~~~~~~~~~
| kmalloc
Signed-off-by: Haiyue Wang <haiyuewa@163.com>
Fixes: 69050f8d6d ("treewide: Replace kmalloc with kmalloc_obj for non-scalar types")
Fixes: bf4afc53b7 ("Convert 'alloc_obj' family to use the new default GFP_KERNEL argument")
Reviewed-by: Kees Cook <kees@kernel.org>
Acked-by: Lasse Collin <lasse.collin@tukaani.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>