Enable UTMI+ phy support for this SoC which is very similar to what
the existing Exynos850 supports.
Add required change in phy driver to support HS phy for this SoC.
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Pritam Manohar Sutar <pritam.sutar@samsung.com>
Link: https://patch.msgid.link/20251124110453.2887437-3-pritam.sutar@samsung.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Document support for the USB20 phy found on the ExynosAutov920 SoC. The
USB20 phy is functionally identical to that on the Exynos850 SoC, so no
driver changes are needed to support this phy. However, add a dedicated
compatible string for USB20 phy found in this SoC.
This phy needs 0.75v, 0.18v and 3.3v supplies for its internal
functionally. Power Supply's names are as per phy's User Data-Book.
These names, (dvdd, vdd18 and vdd33), are considered for 0.75v, 1.8v
and 3.3v respectively.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Pritam Manohar Sutar <pritam.sutar@samsung.com>
Link: https://patch.msgid.link/20251124110453.2887437-2-pritam.sutar@samsung.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Apple Type-C PHY (ATCPHY) is a PHY for USB 2.0, USB 3.x,
USB4/Thunderbolt, and DisplayPort connectivity found in Apple Silicon SoCs.
The PHY handles muxing between these different protocols and also provides
the reset controller for the attached dwc3 USB controller.
There is no documentation available for this PHY and the entire sequence
of MMIO pokes has been figured out by tracing all MMIO access of Apple's
driver under a thin hypervisor and correlating the register reads/writes
to their kernel's debug output to find their names. Deviations from this
sequence generally results in the port not working or, especially when
the mode is switched to USB4 or Thunderbolt, to some watchdog resetting
the entire SoC.
This initial commit already introduces support for Display Port and
USB4/Thunderbolt but the drivers for these are not ready. We cannot
control the alternate mode negotiation and are stuck with whatever Apple's
firmware decides such that any DisplayPort or USB4/Thunderbolt device will
result in a correctly setup PHY but not be usable until the other drivers
are upstreamed as well.
Co-developed-by: Janne Grunau <j@jannau.net>
Signed-off-by: Janne Grunau <j@jannau.net>
Co-developed-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> # for reset controller
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Sven Peter <sven@kernel.org>
Link: https://patch.msgid.link/20251214-b4-atcphy-v3-3-ba82b20e9459@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Apple's Type-C PHY (ATCPHY) is a PHY for USB 2.0, USB 3.x,
USB4/Thunderbolt, and DisplayPort connectivity found in Apple Silicon
SoCs.
The PHY handles muxing between these different protocols and also provides
the reset controller for the attached dwc3 USB controller.
Reviewed-by: Neal Gompa <neal@gompa.dev>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Sven Peter <sven@kernel.org>
Link: https://patch.msgid.link/20251214-b4-atcphy-v3-2-ba82b20e9459@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Various hardware, like the Type-C PHY or the Thunderbolt/USB4 NHI,
present on Apple SoCs need machine-specific tunables passed from our
bootloader m1n1 to the device tree. Add generic helpers so that we
don't have to duplicate this across multiple drivers.
Reviewed-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Reviewed-by: Janne Grunau <j@jannau.net>
Signed-off-by: Sven Peter <sven@kernel.org>
Link: https://patch.msgid.link/20251214-b4-atcphy-v3-1-ba82b20e9459@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add QCS615-specific configuration for USB/DP PHY, including DP init
routines, voltage swing tables, and platform data. Add compatible
"qcs615-qmp-usb3-dp-phy".
Note: SW_PORTSELECT handling for orientation flip is not implemented
due to QCS615 fixed-orientation design and non-standard lane mapping.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-12-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When both USB and DP PHY modes are enabled simultaneously on the same
QMP USBC PHY, it can lead to hardware misconfiguration and undefined
behavior. This happens because the PHY resources are not designed to
operate in both modes at the same time.
To prevent this, introduce a mutual exclusion check between USB and DP
PHY modes.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-10-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The current implementation programs USB-specific registers in
qmp_usbc_com_init(), which is shared by both USB and DP modes. This
causes unnecessary configuration when the PHY is used for DP.
Move USB-only register setup from com_init to qmp_usbc_usb_power_on,
so it runs only for USB mode.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-7-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
USB3DP PHY requires link and vco_div clocks when operating in DP mode.
Extend qmp_usbc_register_clocks and the clock provider logic to register
these clocks along with the existing pipe clock, to support both USB and
DP configurations.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-6-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The original reset list only works for USB-only PHYs. USB3DP PHYs require
different reset names such as "dp_phy", so they need a separate list.
Moving reset configuration into qmp_phy_cfg allows per-PHY customization
without adding special-case logic in DT parsing. The legacy DT path keeps
using the old hardcoded list, while non-legacy paths use cfg->reset_list.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-5-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
QMP USBC PHY drivers previously did not set init_load_uA for regulators,
which could result in incorrect vote levels. This patch introduces
regulator definitions with proper init_load_uA values based on each
chip's power grid design.
QCS615 USB3 PHY was previously reusing qcm2290_usb3phy_cfg, but its
regulator requirements differ. A new qcs615_usb3phy_cfg is added to
reflect the correct settings.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-4-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Extend qmp_usbc_offsets and qmp_phy_cfg with DP-specific fields,
including register offsets, init tables, and callback hooks. Also
update qmp_usbc struct to track DP-related resources and state.
This enables support for USB/DP switchable Type-C PHYs that operate
in either mode.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-3-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To support following DisplayPort (DP) mode over the Type-C PHY, rename
USB-specific functions and ops to clearly separate them from common or
DP-related logic.
This is a preparatory cleanup to enable USB + DP dual mode.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-2-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add device tree binding documentation for the Qualcomm QMP USB3+DP PHY
on QCS615 Platform. This PHY supports both USB3 and DP functionality
over USB-C, with PHY mode switching capability. It does not support
combo mode.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-1-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Document the TI TCAN1046 automotive CAN transceiver. The TCAN1046 is a
dual high-speed CAN transceiver with sleep-mode support and no EN pin,
mirroring the behaviour of the NXP TJA1048, which also provides dual
channels and STB1/2 sleep-control lines.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251209162119.2038313-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Set the regulator load before enabling the regulators to ensure stable
operation and proper power management on platforms where regulators are
shared between the QMP USB PHY and other IP blocks.
Introduce a regulator data structure with explicit enable load values and
use the regulator framework's `init_load_uA` field along with
`devm_regulator_bulk_get_const()` to ensure that `regulator_set_load()` is
applied automatically before the first enable, providing consistent power
management behavior across platforms.
Signed-off-by: Faisal Hassan <faisal.hassan@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20250905101243.14815-1-faisal.hassan@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add QMP PCIe PHY support for the Kaanapali platform.
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20251124-kaanapali-pcie-phy-v4-5-d04ee9cca83b@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some qserdes-com register offsets for the v8 PHY were previously omitted,
as they were not needed by earlier v8 PHY initialization sequences. Add
these missing v8 register offsets now required to support PCIe QMP PHY on
Kaanapali platform.
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Link: https://patch.msgid.link/20251124-kaanapali-pcie-phy-v4-4-d04ee9cca83b@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Kaanapali SoC uses QMP phy with version v8 for PCIe Gen3 x2. Add the new
PCS PCIE specific offsets in a dedicated header file.
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Link: https://patch.msgid.link/20251124-kaanapali-pcie-phy-v4-3-d04ee9cca83b@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Kaanapali SoC uses QMP PHY with version v8 for PCIe Gen3 x2, but requires
a completely unique qserdes-txrx register offsets compared to existing v8
offsets.
Hence, add a dedicated header file containing the FULL SET of qserdes-txrx
register definitions required for Kaanapali's PCIe PHY operation.
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Link: https://patch.msgid.link/20251124-kaanapali-pcie-phy-v4-2-d04ee9cca83b@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Introduce a driver that supports three PHYs found on the SpacemiT
K1 SoC. The first PHY is a combo PHY that can be configured for
use for either USB 3 or PCIe. The other two PHYs support PCIe
only.
All three PHYs must be programmed with an 8 bit receiver termination
value, which must be determined dynamically. Only the combo PHY is
able to determine this value. The combo PHY performs a special
calibration step at probe time to discover this, and that value is
used to program each PHY that operates in PCIe mode. The combo
PHY must therefore be probed before either of the PCIe-only PHYs
will be used.
Each PHY has an internal PLL driven from an external oscillator.
This PLL started when the PHY is first initialized, and stays
on thereafter.
During normal operation, the USB or PCIe driver using the PHY must
ensure (other) clocks and resets are set up properly.
However PCIe mode clocks are enabled and resets are de-asserted
temporarily by this driver to perform the calibration step on the
combo PHY.
Tested-by: Junzhong Pan <panjunzhong@linux.spacemit.com>
Signed-off-by: Alex Elder <elder@riscstar.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/all/ba532f8d-a452-40e5-af46-b58b89f70a92@linaro.org/ [1]
Tested-by: Yixun Lan <dlan@gentoo.org>
Link: https://patch.msgid.link/20251218151235.454997-4-elder@riscstar.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the Device Tree binding for the PCIe/USB 3.0 combo PHY found in
the SpacemiT K1 SoC. This is one of three PCIe PHYs, and is unusual
in that only the combo PHY can perform a calibration step needed to
determine settings used by the other two PCIe PHYs.
Calibration must be done with the combo PHY in PCIe mode, and to allow
this to occur independent of the eventual use for the PHY (PCIe or USB)
some PCIe-related properties must be supplied: clocks; resets; and a
syscon phandle.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Alex Elder <elder@riscstar.com>
Link: https://lore.kernel.org/all/ba532f8d-a452-40e5-af46-b58b89f70a92@linaro.org/ [1]
Tested-by: Yixun Lan <dlan@gentoo.org>
Link: https://patch.msgid.link/20251218151235.454997-2-elder@riscstar.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
MT8195's HDMI PHY block has 4 clocks instead of just a single one.
Describe the extra clocks for it.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
[Louis-Alexis Eyraud: addressed feedback from mailing list]
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20251217-mtk-genio-evk-hdmi-support-v2-3-a994976bb39a@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add compatible string for the HDMI PHY IP on MT8188 SoC, that is
compatible with the one found on MT8195 SoC.
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20251217-mtk-genio-evk-hdmi-support-v2-2-a994976bb39a@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For all of the HDMI PHYs compatible with the one found on MT8195
the output clock has a different datasheet name and specifically
it is called "hdmi_txpll", differently from the older HDMI PHYs
which output block is called "hdmitx_dig_cts".
Replace clock output name string check by max item number one to allow
the new name on all of the HDMI PHY IPs that are perfectly compatible
with MT8195.
[Louis-Alexis Eyraud: split patch, addressed previous feedback from
mailing list, and reworded description]
Fixes: c78fe548b0 ("dt-bindings: phy: mediatek: hdmi-phy: Add mt8195 compatible")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Link: https://patch.msgid.link/20251217-mtk-genio-evk-hdmi-support-v2-1-a994976bb39a@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Drop a bunch of unused members from struct ropll_config and make the
static ropll_tmds_cfg table more readable:
* add a table header
* sort rows by rate
* convert hex values to decimal (for consistency)
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://patch.msgid.link/20251221-phy-hdptx-pll-fix-v2-2-ae4abf7f75a1@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Attempting to make use of a 1080p@120Hz display mode with 10 bpc RGB on
my Acer XV275K P3 monitor results in a blank image. A similar behavior
has been reported on Philips 279M1RV.
The faulty modeline is created by drm_gtf_mode_complex() based on the
following EDID entry from the Standard Timings block:
GTF: 1920x1080 119.999987 Hz 16:9 138.840 kHz 368.759000 MHz
It's worth noting the computed pixel clock ends up being slightly higher
at 368.881000 MHz. Nevertheless, this seems to work consistently fine
with 8 bpc RGB.
After switching to 10 bpc, the TMDS character rate expected for the mode
increases to 461.101250 MHz, as per drm_hdmi_compute_mode_clock().
Since there is no entry for this rate in the ropll_tmds_cfg table, the
necessary HDMI PLL configuration parameters are calculated dynamically
by rk_hdptx_phy_clk_pll_calc(). However, the resulting output rate is
not quite a perfect match, i.e. 461.100000 MHz. That proved to be the
actual root cause of the problem.
Add a new entry to the TMDS configuration table and provide the
necessary frequency division coefficients for the PHY PLL to generate
the expected 461.101250 MHz output.
Fixes: 9d0ec51d7c ("phy: rockchip: samsung-hdptx: Add high color depth management")
Tested-by: Derek Foreman <derek.foreman@collabora.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://patch.msgid.link/20251221-phy-hdptx-pll-fix-v2-1-ae4abf7f75a1@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
According to IC engineer suggestion, set ssc_range as -4003 ppm
will have more tolerance for EMI, and suitable for more boards.
Besides, it's confirmed that with this setting the TX SSC test
will pass on one customer board.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20251219081354.3806806-1-xu.yang_2@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PHY core defines phy_pm_runtime_put() to return an int, but that
return value is never used. It also passes the return value of
pm_runtime_put() to the caller which is not very useful.
Returning an error code from pm_runtime_put() merely means that it has
not queued up a work item to check whether or not the device can be
suspended and there are many perfectly valid situations in which that
can happen, like after writing "on" to the devices' runtime PM "control"
attribute in sysfs for one example.
Modify phy_pm_runtime_put() to discard the pm_runtime_put() return
value and change its return type to void. Also drop the redundant
pm_runtime_enabled() call from there.
No intentional functional impact.
This will facilitate a planned change of the pm_runtime_put() return
type to void in the future.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/2556645.jE0xQCEvom@rafael.j.wysocki
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Passing pm_runtime_put() return value to the callers is not particularly
useful.
Returning an error code from pm_runtime_put() merely means that it has
not queued up a work item to check whether or not the device can be
suspended and there are many perfectly valid situations in which that
can happen, like after writing "on" to the devices' runtime PM "control"
attribute in sysfs for one example. It also happens when the kernel is
configured with CONFIG_PM unset.
Accordingly, update samsung_mipi_dcphy_exit() to simply discard the
return value of pm_runtime_put() and always return success to the
caller.
This will facilitate a planned change of the pm_runtime_put() return
type to void in the future.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/2281919.Icojqenx9y@rafael.j.wysocki
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Printing error messages on pm_runtime_put() returning negative values
is not particularly useful.
Returning an error code from pm_runtime_put() merely means that it has
not queued up a work item to check whether or not the device can be
suspended and there are many perfectly valid situations in which that
can happen, like after writing "on" to the devices' runtime PM "control"
attribute in sysfs for one example.
Accordingly, update mixel_lvds_phy_reset() to simply discard the return
value of pm_runtime_put().
This will facilitate a planned change of the pm_runtime_put() return
type to void in the future.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/2012926.taCxCBeP46@rafael.j.wysocki
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add compatibles for the USB3.0 PHY used in the RZ/V2H(P) and RZ/V2N SoCs.
These SoCs integrate the same USB3 PHY IP block as the RZ/G3E, so the
RZ/G3E compatible is used as a fallback for both.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://patch.msgid.link/20251222161846.152952-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The only core fix is in doc; all the others are in drivers, with the
biggest impacts in libsas being the rollback on error handling and in
ufs coming from a couple of error handling fixes, one causing a crash
if it's activated before scanning and the other fixing W-LUN
resumption.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iLgEABMIAGAWIQTnYEDbdso9F2cI+arnQslM7pishQUCaT4RWBsUgAAAAAAEAA5t
YW51MiwyLjUrMS4xMSwyLDImHGphbWVzLmJvdHRvbWxleUBoYW5zZW5wYXJ0bmVy
c2hpcC5jb20ACgkQ50LJTO6YrIVfSgEA23oY0kPjLLkNj4KAjLoWVPmZ/5efKw49
m6YUwfvzTS8BAIq4eFHVecwAM8FAe9NwuOKgO5d9u6epAy6wzBeP2jly
=cpHq
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"The only core fix is in doc; all the others are in drivers, with the
biggest impacts in libsas being the rollback on error handling and in
ufs coming from a couple of error handling fixes, one causing a crash
if it's activated before scanning and the other fixing W-LUN
resumption"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: qcom: Fix confusing cleanup.h syntax
scsi: libsas: Add rollback handling when an error occurs
scsi: device_handler: Return error pointer in scsi_dh_attached_handler_name()
scsi: ufs: core: Fix a deadlock in the frequency scaling code
scsi: ufs: core: Fix an error handler crash
scsi: Revert "scsi: libsas: Fix exp-attached device scan after probe failure scanned in again after probe failed"
scsi: ufs: core: Fix RPMB link error by reversing Kconfig dependencies
scsi: qla4xxx: Use time conversion macros
scsi: qla2xxx: Enable/disable IRQD_NO_BALANCING during reset
scsi: ipr: Enable/disable IRQD_NO_BALANCING during reset
scsi: imm: Fix use-after-free bug caused by unfinished delayed work
scsi: target: sbp: Remove KMSG_COMPONENT macro
scsi: core: Correct documentation for scsi_device_quiesce()
scsi: mpi3mr: Prevent duplicate SAS/SATA device entries in channel 1
scsi: target: Reset t_task_cdb pointer in error case
scsi: ufs: core: Fix EH failure after W-LUN resume error
client from Max, a fix that hardens osdmap parsing code from myself
(marked for stable) and a few assorted fixups.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAmk8YxITHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi702B/9Mfj0HQSAaWCyMz6GJAv8+1ijVTSbG
nTFeMmipYZhPn188OvWqHsf1cw9rWY0fzenIEW05Tk3YmMvYdeRmCcOkZdeG06xw
um8XxX4L8315E0b98CCpQpVa02ux7XoNtBPjeHccl8PEErJQgQJrQ3Cc/C8kk5U5
a0KlfeVRXYWkOPJva3+wosOu0t9QgJ9ABt5stqcvYDfdkKfvatQMBN3N1nNRKkFH
yhNPv+nRtypSk8jiHhKeeCVmosC0L7MnKuO593vDr761cY5mKrgKFqc2LLlPF6r0
/p13s5SG6X38RUegWCjcK4XRJAzVcR/tyod8LkVVp8d5DC/ptcyy8H+I
=h1gC
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-6.19-rc1' of https://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"We have a patch that adds an initial set of tracepoints to the MDS
client from Max, a fix that hardens osdmap parsing code from myself
(marked for stable) and a few assorted fixups"
* tag 'ceph-for-6.19-rc1' of https://github.com/ceph/ceph-client:
rbd: stop selecting CRC32, CRYPTO, and CRYPTO_AES
ceph: stop selecting CRC32, CRYPTO, and CRYPTO_AES
libceph: make decode_pool() more resilient against corrupted osdmaps
libceph: Amend checking to fix `make W=1` build breakage
ceph: Amend checking to fix `make W=1` build breakage
ceph: add trace points to the MDS client
libceph: fix log output race condition in OSD client
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=jbkd
-----END PGP SIGNATURE-----
Merge tag 'smp-urgent-2025-12-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull CPU hotplug fix from Ingo Molnar:
- Fix CPU hotplug callbacks to disable interrupts on UP kernels
* tag 'smp-urgent-2025-12-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu: Make atomic hotplug callbacks run with interrupts disabled on UP
individual changelogs for details.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCaTsgBwAKCRDdBJ7gKXxA
jkSIAP4jD66nEC2QyKTiv9XvXi8rpKz6RGAHNZSam0ucI5WKswEAoflmlqsoD/Kk
sN3YLwLztzCJIYU7tT3IRaPK0irwDAo=
=nkux
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2025-12-11-11-47' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc updates from Andrew Morton:
"There are no significant series in this small merge. Please see the
individual changelogs for details"
[ Editor's note: it's mainly ocfs2 and a couple of random fixes ]
* tag 'mm-nonmm-stable-2025-12-11-11-47' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm: memfd_luo: add CONFIG_SHMEM dependency
mm: shmem: avoid build warning for CONFIG_SHMEM=n
ocfs2: fix memory leak in ocfs2_merge_rec_left()
ocfs2: invalidate inode if i_mode is zero after block read
ocfs2: avoid -Wflex-array-member-not-at-end warning
ocfs2: convert remaining read-only checks to ocfs2_emergency_state
ocfs2: add ocfs2_emergency_state helper and apply to setattr
checkpatch: add uninitialized pointer with __free attribute check
args: fix documentation to reflect the correct numbers
ocfs2: fix kernel BUG in ocfs2_find_victim_chain
liveupdate: luo_core: fix redundant bound check in luo_ioctl()
ocfs2: validate inline xattr size and entry count in ocfs2_xattr_ibody_list
fs/fat: remove unnecessary wrapper fat_max_cache()
ocfs2: replace deprecated strcpy with strscpy
ocfs2: check tl_used after reading it from trancate log inode
liveupdate: luo_file: don't use invalid list iterator
- The 2 patch series "powerpc/pseries/cmm: two smaller fixes" from David
Hildenbrand fixes a couple of minor things in ppc land.
- The 4 patch series "Improve folio split related functions" from Zi Yan
provides some cleanups and minorish fixes in the folio splitting code.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCaTseCwAKCRDdBJ7gKXxA
jkCLAP9ttvtG7zhDf+tqvjCJFnybPEo6Z2B4Qx9g8i7s27gTZgD8DzYbIl+YdxrN
/tS0tdgUfrJIXR2PzzipkydNrs+lxgg=
=T65o
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2025-12-11-11-39' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull more MM updates from Andrew Morton:
- "powerpc/pseries/cmm: two smaller fixes" (David Hildenbrand)
fixes a couple of minor things in ppc land
- "Improve folio split related functions" (Zi Yan)
some cleanups and minorish fixes in the folio splitting code
* tag 'mm-stable-2025-12-11-11-39' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/damon/tests/core-kunit: avoid damos_test_commit stack warning
mm: vmscan: correct nr_requested tracing in scan_folios
MAINTAINERS: add idr core-api doc file to XARRAY
mm/hugetlb: fix incorrect error return from hugetlb_reserve_pages()
mm: fix CONFIG_STACK_GROWSUP typo in mm.h
mm/huge_memory: fix folio split stats counting
mm/huge_memory: make min_order_for_split() always return an order
mm/huge_memory: replace can_split_folio() with direct refcount calculation
mm/huge_memory: change folio_split_supported() to folio_check_splittable()
mm/sparse: fix sparse_vmemmap_init_nid_early definition without CONFIG_SPARSEMEM
powerpc/pseries/cmm: adjust BALLOON_MIGRATE when migrating pages
powerpc/pseries/cmm: call balloon_devinfo_init() also without CONFIG_BALLOON_COMPACTION
Brown paper bag time. This is a silly oversight where I missed to drop
the error condition checking to ensure we clean up on early error
returns. I have an internal unit testset coming up for this which will
catch all such issues going forward.
Reported-by: Chris Mason <clm@fb.com>
Reported-by: Jeff Layton <jlayton@kernel.org>
Fixes: 011703a9ac ("file: add FD_{ADD,PREPARE}()")
Signed-off-by: Christian Brauner <brauner@kernel.org>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
