There are several thermal sensors that only have a low-speed bus
interface but output valid video data. This patchset enables support
for the AMG88xx "Grid-Eye" sensor family.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
[hans.verkuil@cisco.com: split up int ret = ...->xfer(); line]
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Define the device tree bindings for the panasonic,amg88xx i2c
video driver.
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This is Open Firmware driver, hence 'of_device.h' should be included
instead of 'platform_device.h'. Right now OF headers happen to be included
indirectly and this may break in the future, so let's correct the header.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Do not handle interrupts if we haven't asked for them, potentially that
could happen if HW wasn't programmed properly.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Stride of U/V planes must be aligned to 16 bytes (2 macroblocks). This
needs to be taken into account, otherwise it is possible to get a silent
memory corruption if dmabuf size is less than the size of decoded video
frame.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make all strings single line to make them grep'able and add a comment
to the memory barrier.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
I've noticed that decoding fails sometime if size of bitstream buffer
isn't aligned to 16K, probably because HW fetches data from memory in
a 16K granularity and if the last chunk of data isn't aligned, HW reads
garbage data beyond the dmabuf and tries to parse it.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Following commit f773568b6f ("drm/i915: nuke the duplicated stolen
discovery"), the if-else-chain for determining the GTT size is redundant
with the !chv branches all being the same.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
References: f773568b6f ("drm/i915: nuke the duplicated stolen discovery")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180503212956.3948-1-chris@chris-wilson.co.uk
From now on, I'll start using my @kernel.org as my development e-mail.
As such, let's remove the entries that point to the old
mchehab@s-opensource.com at MAINTAINERS file.
For the files written with a copyright with mchehab@s-opensource,
let's keep Samsung on their names, using mchehab+samsung@kernel.org,
in order to keep pointing to my employer, with sponsors the work.
For the files written before I join Samsung (on July, 4 2013),
let's just use mchehab@kernel.org.
For bug reports, we can simply point to just kernel.org, as
this will reach my mchehab+samsung inbox anyway.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Brian Warner <brian.warner@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix inconsistent IS_ERR and PTR_ERR in imx_csi_probe.
The proper pointer to be passed as argument is pinctrl
instead of priv->vdev.
This issue was detected with the help of Coccinelle.
Fixes: 52e17089d1 ("media: imx: Don't initialize vars that won't be used")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are quite a few code snippet like the following in verifier:
subprog_start = 0;
if (env->subprog_cnt == cur_subprog + 1)
subprog_end = insn_cnt;
else
subprog_end = env->subprog_info[cur_subprog + 1].start;
The reason is there is no marker in subprog_info array to tell the end of
it.
We could resolve this issue by introducing a faked "ending" subprog.
The special "ending" subprog is with "insn_cnt" as start offset, so it is
serving as the end mark whenever we iterate over all subprogs.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
It is better to centre all subprog information fields into one structure.
This structure could later serve as function node in call graph.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Currently, verifier treat main prog and subprog differently. All subprogs
detected are kept in env->subprog_starts while main prog is not kept there.
Instead, main prog is implicitly defined as the prog start at 0.
There is actually no difference between main prog and subprog, it is better
to unify them, and register all progs detected into env->subprog_starts.
This could also help simplifying some code logic.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Using drm_atomic_get_private_obj_state() after state has been swapped
will return old state.
Fixes: 0281c41490 ("drm/tegra: hub: Use private object for global state")
Signed-off-by: Stefan Schake <stschake@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
We want to add more DRM selftests, and there's not much point in
having a Kconfig option for every single one of them, so make
a generic one.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180503112217.37292-5-maarten.lankhorst@linux.intel.com
[mlankhorst: Fix i915/Kconfig.debug (ickle)]
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the previous patch drm_atomic_helper_check_plane_state correctly
calculates clipping and the xf86-video-intel ddx is fixed to fall back
to GPU correctly when SetPlane fails, we can remove the hack where
we try to pan/zoom when out of min/max scaling range. This was already
poor behavior where the screen didn't show what was requested, and now
instead we reject it outright. This simplifies check_sprite_plane a lot.
Changes since v1:
- Set crtc_h to the height correctly.
- Reject < 3x3 rectangles instead of making them invisible for <gen9.
For gen9+ skl_update_scaler_plane will reject them.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180503112217.37292-4-maarten.lankhorst@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Document the R-Car V3H (R8A77980) SoC in the R-Car PCIe bindings.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Rob Herring <robh@kernel.org>
rcar_pcie_hw_init_{h1|gen2|gen3}() only differ in the PCIe PHY init code
and all end with a call to rcar_pcie_hw_init(), thus it makes sense to
move that call into the driver's probe() method and then rename those
functions to rcar_pcie_phy_init_{h1|gen2|gen3}().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Commit 7ed1c1901f (tools: fix cross-compile var clobbering) removed
setting of LD to $(CROSS_COMPILE)gcc. This broke build of acpica
(acpidump) in power/acpi:
ld: unrecognized option '-D_LINUX'
The tools pass CFLAGS to the linker (incl. -D_LINUX), so revert this
particular change and let LD be $(CC) again. Note that the old behaviour
was a bit different, it used $(CROSS_COMPILE)gcc which was eliminated by
the commit 7ed1c1901f. We use $(CC) for that reason.
Fixes: 7ed1c1901f (tools: fix cross-compile var clobbering)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: 4.16+ <stable@vger.kernel.org> # 4.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On R-Car gen3 SoCs the PCIe PHY has its own register region, thus we
need to add the corresponding code in rcar_pcie_hw_init_gen3() and call
devm_phy_optional_get() at the driver's probing time, so that the
existing R-Car gen3 device trees (not having a PHY node) would still
work (we only need to power up the PHY on R-Car V3H).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Rob Herring <robh@kernel.org>
The U8540 was an evolved version of the U8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the U8500.
Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of relying on a scale which may increase rounding errors,
clip src by doing: src * (dst - clip) / dst and rounding the result
away from 1, so the new coordinates get closer to 1. We won't need
to fix up with a magic macro afterwards, because our scaling factor
will never go to the other side of 1.
Changes since v1:
- Adjust dst immediately, else drm_rect_width/height on dst gives bogus
results.
Change since v2:
- Get rid of macros and use 64-bits math.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[mlankhorst: Add Villes comment, and rename newsrc to tmp. (Ville)]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180503112217.37292-3-maarten.lankhorst@linux.intel.com
Since rcar_pcie_hw_init() is polling PCIEPHYSR.PHYRDY there is no need
anymore for polling the PHY specific register in rcar_pcie_hw_init_h1().
Remove it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
These systems are not plentiful and do not have any
strict memory constraints. Cut down the configurability
and select what is needed for all of them so they simply boot,
keeping only the UX500_SOC_DB8500 symbol which is used
elsewhere in the kernel for now, but default it to y.
Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The U8540 was an evolved version of the U8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the U8500.
Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In all the R-Car gen1/2/3 manuals, we are instructed to poll PCIEPHYSR
for PHYRDY=1 at an early stage of the PCIEC initialization -- while
the driver only does this on R-Car H1 (polling a PHY specific register).
Add the PHYRDY polling to rcar_pcie_hw_init(). Note that without the
special PHY driver on the R-Car V3H (R8A77980) the PCIEC initialization
just freezes the kernel -- adding the PHYRDY polling allows the init code
to exit gracefully on timeout (PHY starts powered down after reset on this
SoC).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
When calculating limits we want to be as pessimistic as possible,
so we have to explicitly say whether we want to round up or down
to accurately calculate whether we are below min_scale or above
max_scale.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[mlankhorst: Fix wording in documentation. (Ville)]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180503112217.37292-2-maarten.lankhorst@linux.intel.com
One layout supported by the Marvell NAND controller supports NAND pages
of 2048 bytes, all handled in one single chunk when using BCH with a
strength of 4-bit per 512 bytes. In this case, instead of the generic
XTYPE_WRITE_DISPATCH/XTYPE_LAST_NAKED_RW couple, the controller expects
to receive XTYPE_MONOLITHIC_RW.
This fixes problems at boot like:
[ 1.315475] Scanning device for bad blocks
[ 3.203108] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[ 3.209564] nand_bbt: error while writing BBT block -110
[ 4.243106] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[ 5.283106] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[ 5.289562] nand_bbt: error -110 while marking block 2047 bad
[ 6.323106] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[ 6.329559] nand_bbt: error while writing BBT block -110
[ 7.363106] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[ 8.403105] marvell-nfc f10d0000.flash: Timeout waiting for RB signal
[ 8.409559] nand_bbt: error -110 while marking block 2046 bad
...
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
marvell_nfc_wait_op() expects the delay to be expressed in milliseconds
but nand_sdr_timings uses picoseconds. Use PSEC_TO_MSEC when passing
tPROG_max to marvell_nfc_wait_op().
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
struct xfrm_state is rather large (768 bytes here) and therefore wastes
quite a lot of memory as it falls into the kmalloc-1024 slab cache,
leaving 256 bytes of unused memory per XFRM state object -- a net waste
of 25%.
Using a dedicated slab cache for struct xfrm_state reduces the level of
internal fragmentation to a minimum.
On my configuration SLUB chooses to create a slab cache covering 4
pages holding 21 objects, resulting in an average memory waste of ~13
bytes per object -- a net waste of only 1.6%.
In my tests this led to memory savings of roughly 2.3MB for 10k XFRM
states.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Call sync_entity_load_avg() directly from find_idlest_cpu() instead of
select_task_rq_fair(), as that's where we need to use task's utilization
value. And call sync_entity_load_avg() only after making sure sched
domain spans over one of the allowed CPUs for the task.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Link: http://lkml.kernel.org/r/cd019d1753824c81130eae7b43e2bbcec47cc1ad.1524738578.git.viresh.kumar@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Rearrange select_task_rq_fair() a bit to avoid executing some
conditional statements in few specific code-paths. That gets rid of the
goto as well.
This shouldn't result in any functional changes.
Tested-by: Rohit Jain <rohit.k.jain@oracle.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Link: http://lkml.kernel.org/r/20831b8d237bf3a20e4e328286f678b425ff04c9.1524738578.git.viresh.kumar@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
S70GL02GS flash reports a single 256 MiB chip, but is really made up
of two 128 MiB chips with 1024 sectors each.
Without early fixups (top half of device cannot be written or erased):
ff0000000.nor-boot: Found 1 x16 devices at 0x0 in 16-bit bank. <snip>
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.5.
number of CFI chips: 1
With early fixups (entire device can be written and erased):
Bad S70GL02GS CFI data; adjust to detect 2 chips
ff0000000.nor-boot: Found 1 x16 devices at 0x0 in 16-bit bank. <snip>
ff0000000.nor-boot: Found 1 x16 devices at 0x8000000 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.5.
number of CFI chips: 2
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Some CFI devices need fixups that affect the number of chips detected,
but the current fixup infrastructure (struct cfi_fixup and cfi_fixup())
does not cover this situation.
Introduce struct cfi_early_fixup and cfi_early_fixup() to fill the void.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
LPTimer pwm cells should be updated to 3, to allow initialization of
channel, period and polarity.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add display support on the stm32f469-disco board.
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
In the stm32f4 family, mipi dsi is only supported on stm32f469.
So add a new stm32f469 dtsi file & add mipi dsi support inside.
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Since commit 83a86fbb5b ("irqchip/gic: Loudly complain about
the use of IRQ_TYPE_NONE"), a warning is raised if IRQ_TYPE_NONE is used.
So we use IRQ_TYPE_LEVEL_HIGH for usart nodes instead of IRQ_TYPE_NONE.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Tested-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Fix DTC warnings for stm32mp157:
Warning (unit_address_vs_reg): /soc/pin-controller: node has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): /soc/pin-controller/uart4@0: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /soc/pin-controller-z: node has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>