Add support for the new compatible added specifically to support
k2g's MMC/SD controller.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add binding for the TI's sdhci-omap controller present in K2G.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Errata i834 in AM572x Sitara Processors Silicon Revision 2.0, 1.1
(SPRZ429K July 2014–Revised March 2017 [1]) mentions the maximum
obtainable timeout through MMC host controller is 700ms. And for
commands taking longer than 700ms, hardware timeout should be
disabled and software timeout should be used.
The workaround for Errata i834 can be achieved by adding
SDHCI_QUIRK2_DISABLE_HW_TIMEOUT quirk in sdhci-omap.
[1] -> http://www.ti.com/lit/er/sprz429k/sprz429k.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci has a 10 second timeout to catch devices that stop responding.
In the case of quirk SDHCI_QUIRK2_DISABLE_HW_TIMEOUT, instead of
programming 10 second arbitrary value, calculate the total time it would
take for the entire transfer to happen and program the timeout value
accordingly.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out the target_timeout calculation so it can be re-used.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add quirk to disable HW timeout if the requested timeout is more than the
maximum obtainable timeout.
Also, if the quirk is set and ->get_max_timeout_count() is not implemented,
max_busy_timeout is set to zero.
Based-on-patch-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI controller in a SoC might support HS200/HS400 (indicated
using mmc-hs200-1_8v/mmc-hs400-1_8v dt property), but if the board is
modeled such that the IO lines are not connected to 1.8v then
HS200/HS400 cannot be supported. Disable HS200/HS400 if the board
does not have 1.8v connected to the IO lines. Also Disable DDR/UHS in 1.8v
if the IO lines are not connected to 1.8v.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Invoke sdhci_get_of_property defined in sdhci-pltfm.c to read
sdhci specific properties from dt node.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Errata i843 in AM572x Sitara Processors Silicon Revision 2.0, 1.1
(SPRZ429K July 2014–Revised March 2017 [1]) mentions
PG 1.0/1.1 silicon has limitations w.r.t frequencies at which MMC1/2/3
can operate.
Use soc_device_match() to identify rev 1.0/1.1 silicon and
override mmc->f_max according to the errata workaround.
"max-frequency" dt property cannot be used since the device
tree is added for rev 2.0 silicon.
soc_device_match() is also used in order to get the IODelay values
for rev 1.0/1.1 silicon.
[1] -> http://www.ti.com/lit/er/sprz429k/sprz429k.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci can directly get ADMA capability from MMCHS_CAPA register.
Remove explicitly setting ADMA here as some instances might not have
ADMA enabled. (sdhci_read_caps() is also removed from here since
sdhci_setup_host() invokes it).
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_omap_config_iodelay_pinctrl_state() requires caps and caps2 to be
initialized (speed mode capabilities like UHS/HS200) before it is
invoked. While mmc_of_parse() initializes caps/caps2 if capabilities is
populated in device tree, it will remain uninitialized for capabilities
obtained from SDHCI_CAPABILITIES register.
Fix sdhci_omap_config_iodelay_pinctrl_state() to be used even while
getting the capabilities from SDHCI_CAPABILITIES register by invoking
sdhci_setup_host() before sdhci_omap_config_iodelay_pinctrl_state().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Even with the wait-loop fixed, there is a further issue with
kthread_parkme(). Upon hotplug, when we do takedown_cpu(),
smpboot_park_threads() can return before all those threads are in fact
blocked, due to the placement of the complete() in __kthread_parkme().
When that happens, sched_cpu_dying() -> migrate_tasks() can end up
migrating such a still runnable task onto another CPU.
Normally the task will have hit schedule() and gone to sleep by the
time we do kthread_unpark(), which will then do __kthread_bind() to
re-bind the task to the correct CPU.
However, when we loose the initial TASK_PARKED store to the concurrent
wakeup issue described previously, do the complete(), get migrated, it
is possible to either:
- observe kthread_unpark()'s clearing of SHOULD_PARK and terminate
the park and set TASK_RUNNING, or
- __kthread_bind()'s wait_task_inactive() to observe the competing
TASK_RUNNING store.
Either way the WARN() in __kthread_bind() will trigger and fail to
correctly set the CPU affinity.
Fix this by only issuing the complete() when the kthread has scheduled
out. This does away with all the icky 'still running' nonsense.
The alternative is to promote TASK_PARKED to a special state, this
guarantees wait_task_inactive() cannot observe a 'stale' TASK_RUNNING
and we'll end up doing the right thing, but this preserves the whole
icky business of potentially migating the still runnable thing.
Reported-by: Gaurav Kohli <gkohli@codeaurora.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Gaurav reported a problem with __kthread_parkme() where a concurrent
try_to_wake_up() could result in competing stores to ->state which,
when the TASK_PARKED store got lost bad things would happen.
The comment near set_current_state() actually mentions this competing
store, but only mentions the case against TASK_RUNNING. This same
store, with different timing, can happen against a subsequent !RUNNING
store.
This normally is not a problem, because as per that same comment, the
!RUNNING state store is inside a condition based wait-loop:
for (;;) {
set_current_state(TASK_UNINTERRUPTIBLE);
if (!need_sleep)
break;
schedule();
}
__set_current_state(TASK_RUNNING);
If we loose the (first) TASK_UNINTERRUPTIBLE store to a previous
(concurrent) wakeup, the schedule() will NO-OP and we'll go around the
loop once more.
The problem here is that the TASK_PARKED store is not inside the
KTHREAD_SHOULD_PARK condition wait-loop.
There is a genuine issue with sleeps that do not have a condition;
this is addressed in a subsequent patch.
Reported-by: Gaurav Kohli <gkohli@codeaurora.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With commit:
31e77c93e4 ("sched/fair: Update blocked load when newly idle")
... we release the rq->lock when updating blocked load of idle CPUs.
This opens a time window during which another CPU can add a task to this
CPU's cfs_rq.
The check for newly added task of idle_balance() is not in the common path.
Move the out label to include this check.
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 31e77c93e4 ("sched/fair: Update blocked load when newly idle")
Link: http://lkml.kernel.org/r/20180426103133.GA6953@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Matt reported the following deadlock:
CPU0 CPU1
schedule(.prev=migrate/0) <fault>
pick_next_task() ...
idle_balance() migrate_swap()
active_balance() stop_two_cpus()
spin_lock(stopper0->lock)
spin_lock(stopper1->lock)
ttwu(migrate/0)
smp_cond_load_acquire() -- waits for schedule()
stop_one_cpu(1)
spin_lock(stopper1->lock) -- waits for stopper lock
Fix this deadlock by taking the wakeups out from under stopper->lock.
This allows the active_balance() to queue the stop work and finish the
context switch, which in turn allows the wakeup from migrate_swap() to
observe the context and complete the wakeup.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reported-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180420095005.GH4064@hirez.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- Tracepoints should not give warning on OOM failures
- Use special field for function pointer in trace event
- Fix igrab issues in uprobes
- Fixes to the new histogram triggers
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCWuoYdBQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qtFnAP9X4+AVDQH0VfsMLSc9D+rK6WmcRIhv
q8J2gNPv3anM+AD/SFXWGO4ihN+0KDw/TqmJxESNEybq47vTZ/s5lM6A4gQ=
=fQbj
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Various fixes in tracing:
- Tracepoints should not give warning on OOM failures
- Use special field for function pointer in trace event
- Fix igrab issues in uprobes
- Fixes to the new histogram triggers"
* tag 'trace-v4.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracepoint: Do not warn on ENOMEM
tracing: Add field modifier parsing hist error for hist triggers
tracing: Add field parsing hist error for hist triggers
tracing: Restore proper field flag printing when displaying triggers
tracing: initcall: Ordered comparison of function pointers
tracing: Remove igrab() iput() call from uprobes.c
tracing: Fix bad use of igrab in trace_uprobe.c
Pull input updates from Dmitry Torokhov:
"Just a few driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: atmel_mxt_ts - add missing compatible strings to OF device table
Input: atmel_mxt_ts - fix the firmware update
Input: atmel_mxt_ts - add touchpad button mapping for Samsung Chromebook Pro
MAINTAINERS: Rakesh Iyer can't be reached anymore
Input: hideep_ts - fix a typo in Kconfig
Input: alps - fix reporting pressure of v3 trackstick
Input: leds - fix out of bound access
Input: synaptics-rmi4 - fix an unchecked out of memory error path
Allow some non-cached routes to use non-expired fnhe:
1. ip_del_fnhe: moved above and now called by find_exception.
The 4.5+ commit deed49df73 expires fnhe only when caching
routes. Change that to:
1.1. use fnhe for non-cached local output routes, with the help
from (2)
1.2. allow __mkroute_input to detect expired fnhe (outdated
fnhe_gw, for example) when do_cache is false, eg. when itag!=0
for unicast destinations.
2. __mkroute_output: keep fi to allow local routes with orig_oif != 0
to use fnhe info even when the new route will not be cached into fnhe.
After commit 839da4d989 ("net: ipv4: set orig_oif based on fib
result for local traffic") it means all local routes will be affected
because they are not cached. This change is used to solve a PMTU
problem with IPVS (and probably Netfilter DNAT) setups that redirect
local clients from target local IP (local route to Virtual IP)
to new remote IP target, eg. IPVS TUN real server. Loopback has
64K MTU and we need to create fnhe on the local route that will
keep the reduced PMTU for the Virtual IP. Without this change
fnhe_pmtu is updated from ICMP but never exposed to non-cached
local routes. This includes routes with flowi4_oif!=0 for 4.6+ and
with flowi4_oif=any for 4.14+).
3. update_or_create_fnhe: make sure fnhe_expires is not 0 for
new entries
Fixes: 839da4d989 ("net: ipv4: set orig_oif based on fib result for local traffic")
Fixes: d6d5e999e5 ("route: do not cache fib route info on local routes with oif")
Fixes: deed49df73 ("route: check and remove route cache when we get route")
Cc: David Ahern <dsahern@gmail.com>
Cc: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three small bug fixes: an illegally overlapping memcmp in target code,
a potential infinite loop in isci under certain rare phy conditions
and an ATA queue depth (performance) correction for storvsc.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWunNPiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdyJAQDGWGGN
i5BJOr1c8BNEMHHuJIYvpgNJDLQd5tfqxieZgAD/e1RQn1nIjxnoIrduOAP+so8u
XvGtP79yTO2yxz7VP48=
=HASg
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three small bug fixes: an illegally overlapping memcmp in target code,
a potential infinite loop in isci under certain rare phy conditions
and an ATA queue depth (performance) correction for storvsc"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: target: Fix fortify_panic kernel exception
scsi: isci: Fix infinite loop in while loop
scsi: storvsc: Set up correct queue depth values for IDE devices
vga-dac: Fix edid memory leak (Sean)
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Sean Paul <seanpaul@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAlrqFqcACgkQlvcN/ahK
BwraMwf+PppfIRNcyvUU3iPu6WiaodD9qOdt55AU6WK8SmEJ0Bk+10XNFjYHXOrA
b/zUo6g7Zru+sneLKhZGwpGkBQ1IcuwichpQGd+OvknT2U8Ee8IwEZib7g9Vpqoi
np4PWKMRI1/XWlCOHvkY6fAV7uVDWjkRKDmeUmpTRaWBQdq/QVAzk1z0hUW93mSY
RqZZTNZBXPsuwW+wIdAIDlm5PSvYBbgEa2HVj44iK4PB7SlI5jGMtjbQpcbmmT20
V4RvvLPeRBCizA5LiSu+HspRCvtBZfSHt5nRqONc11bmK0DjiZt8tBSsbHEUHEt6
ySDjbjk2RVwVAE5wV3Z7xKT1CQOBZg==
=yyCu
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2018-05-02' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
vc4: Fix bo refcounts during async commits (Boris)
vga-dac: Fix edid memory leak (Sean)
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Sean Paul <seanpaul@chromium.org>
* tag 'drm-misc-fixes-2018-05-02' of git://anongit.freedesktop.org/drm/drm-misc:
drm/bridge: vga-dac: Fix edid memory leak
drm/vc4: Make sure vc4_bo_{inc,dec}_usecnt() calls are balanced
Add DMC firmware for Geminilake.
* tag 'drm-intel-fixes-2018-05-02' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915/glk: Add MODULE_FIRMWARE for Geminilake
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, the check that ret_val is not -ENOENT is always true and
the quirk bit BYT_RY5651_MCLK_EN is never being cleared because ret_val
is always zero at this point from a previous assignment earlier on.
I believe that ret_val should actually be assigned to the return from
devm_clk_get() as this can return -ENOENT (from a deeper call to
clk_get_sys) and that was the original intention to check this.
Detected by CoverityScan, CID#1460228 ("Logically dead code")
Fixes: 02c0a3b304 ("ASoC: Intel: bytcr_rt5651: add MCLK, quirks and cleanups")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf 2018-05-03
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Several BPF sockmap fixes mostly related to bugs in error path
handling, that is, a bug in updating the scatterlist length /
offset accounting, a missing sk_mem_uncharge() in redirect
error handling, and a bug where the outstanding bytes counter
sg_size was not zeroed, from John.
2) Fix two memory leaks in the x86-64 BPF JIT, one in an error
path where we still don't converge after image was allocated
and another one where BPF calls are used and JIT passes don't
converge, from Daniel.
3) Minor fix in BPF selftests where in test_stacktrace_build_id()
we drop useless args in urandom_read and we need to add a missing
newline in a CHECK() error message, from Song.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to move to a more flexible timeline that doesn't assume one
fence context per engine, and so allow for a single timeline to be used
across a combination of engines. This means that preallocating a fence
context per engine is now a hindrance, and so we want to introduce the
singular timeline. From the code perspective, this has the notable
advantage of clearing up a lot of mirky semantics and some clumsy
pointer chasing.
By splitting the timeline up into a single entity rather than an array
of per-engine timelines, we can realise the goal of the previous patch
of tracking the timeline alongside the ring.
v2: Tweak wait_for_idle to stop the compiling thinking that ret may be
uninitialised.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180502163839.3248-2-chris@chris-wilson.co.uk
In the future, we want to move a request between engines. To achieve
this, we first realise that we have two timelines in effect here. The
first runs through the GTT is required for ordering vma access, which is
tracked currently by engine. The second is implied by sequential
execution of commands inside the ringbuffer. This timeline is one that
maps to userspace's expectations when submitting requests (i.e. given the
same context, batch A is executed before batch B). As the rings's
timelines map to userspace and the GTT timeline an implementation
detail, move the timeline from the GTT into the ring itself (per-context
in logical-ring-contexts/execlists, or a global per-engine timeline for
the shared ringbuffers in legacy submission.
The two timelines are still assumed to be equivalent at the moment (no
migrating requests between engines yet) and so we can simply move from
one to the other without adding extra ordering.
v2: Reinforce that one isn't allowed to mix the engine execution
timeline with the client timeline from userspace (on the ring).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180502163839.3248-1-chris@chris-wilson.co.uk
02bfeb4842 ("PCI/portdrv: Simplify PCIe feature permission checking")
removed the only call of pcie_port_acpi_setup() and removed portdrv_acpi.o
from the Makefile, but I forgot to remove pcie_port_acpi_setup() itself.
Remove pcie_port_acpi_setup() and the drivers/pci/pcie/portdrv_acpi.c file.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
John Fastabend says:
====================
When I added the test_sockmap to selftests I mistakenly changed the
test logic a bit. The result of this was on redirect cases we ended up
choosing the wrong sock from the BPF program and ended up sending to a
socket that had no receive handler. The result was the actual receive
handler, running on a different socket, is timing out and closing the
socket. This results in errors (-EPIPE to be specific) on the sending
side. Typically happening if the sender does not complete the send
before the receive side times out. So depending on timing and the size
of the send we may get errors. This exposed some bugs in the sockmap
error path handling.
This series fixes the errors. The primary issue is we did not do proper
memory accounting in these cases which resulted in missing a
sk_mem_uncharge(). This happened in the redirect path and in one case
on the normal send path. See the three patches for the details.
The other take-away from this is we need to fix the test_sockmap and
also add more negative test cases. That will happen in bpf-next.
Finally, I tested this using the existing test_sockmap program, the
older sockmap sample test script, and a few real use cases with
Cilium. All of these seem to be in working correctly.
v2: fix compiler warning, drop iterator variable 'i' that is no longer
used in patch 3.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When a redirect failure happens we release the buffers in-flight
without calling a sk_mem_uncharge(), the uncharge is called before
dropping the sock lock for the redirecte, however we missed updating
the ring start index. When no apply actions are in progress this
is OK because we uncharge the entire buffer before the redirect.
But, when we have apply logic running its possible that only a
portion of the buffer is being redirected. In this case we only
do memory accounting for the buffer slice being redirected and
expect to be able to loop over the BPF program again and/or if
a sock is closed uncharge the memory at sock destruct time.
With an invalid start index however the program logic looks at
the start pointer index, checks the length, and when seeing the
length is zero (from the initial release and failure to update
the pointer) aborts without uncharging/releasing the remaining
memory.
The fix for this is simply to update the start index. To avoid
fixing this error in two locations we do a small refactor and
remove one case where it is open-coded. Then fix it in the
single function.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When an error occurs during a redirect we have two cases that need
to be handled (i) we have a cork'ed buffer (ii) we have a normal
sendmsg buffer.
In the cork'ed buffer case we don't currently support recovering from
errors in a redirect action. So the buffer is released and the error
should _not_ be pushed back to the caller of sendmsg/sendpage. The
rationale here is the user will get an error that relates to old
data that may have been sent by some arbitrary thread on that sock.
Instead we simple consume the data and tell the user that the data
has been consumed. We may add proper error recovery in the future.
However, this patch fixes a bug where the bytes outstanding counter
sg_size was not zeroed. This could result in a case where if the user
has both a cork'ed action and apply action in progress we may
incorrectly call into the BPF program when the user expected an
old verdict to be applied via the apply action. I don't have a use
case where using apply and cork at the same time is valid but we
never explicitly reject it because it should work fine. This patch
ensures the sg_size is zeroed so we don't have this case.
In the normal sendmsg buffer case (no cork data) we also do not
zero sg_size. Again this can confuse the apply logic when the logic
calls into the BPF program when the BPF programmer expected the old
verdict to remain. So ensure we set sg_size to zero here as well. And
additionally to keep the psock state in-sync with the sk_msg_buff
release all the memory as well. Previously we did this before
returning to the user but this left a gap where psock and sk_msg_buff
states were out of sync which seems fragile. No additional overhead
is taken here except for a call to check the length and realize its
already been freed. This is in the error path as well so in my
opinion lets have robust code over optimized error paths.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When the call to do_tcp_sendpage() fails to send the complete block
requested we either retry if only a partial send was completed or
abort if we receive a error less than or equal to zero. Before
returning though we must update the scatterlist length/offset to
account for any partial send completed.
Before this patch we did this at the end of the retry loop, but
this was buggy when used while applying a verdict to fewer bytes
than in the scatterlist. When the scatterlist length was being set
we forgot to account for the apply logic reducing the size variable.
So the result was we chopped off some bytes in the scatterlist without
doing proper cleanup on them. This results in a WARNING when the
sock is tore down because the bytes have previously been charged to
the socket but are never uncharged.
The simple fix is to simply do the accounting inside the retry loop
subtracting from the absolute scatterlist values rather than trying
to accumulate the totals and subtract at the end.
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch clears PageError in some pages tagged by read path, but when we
write the pages with valid contents, writepage should clear the bit likewise
ext4.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch changes the rule to check cap_resource for data blocks, not inode
or node blocks in order to avoid selinux denial.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch reverts copied f2fs_set_page_dirty_nobuffer to use generic function
for stability.
This reverts commit fe76b796fc.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
xfstest generic/429 sometimes hangs on f2fs, caused by a thread being
unable to take a directory's i_rwsem for write in vfs_rmdir(). In the
test, one thread repeatedly creates and removes a directory, and other
threads repeatedly look up a file in the directory. The bug is that
f2fs_mkdir() calls d_instantiate() before unlock_new_inode(), resulting
in the directory inode being exposed to lookups before it has been fully
initialized. And with CONFIG_DEBUG_LOCK_ALLOC, unlock_new_inode()
reinitializes ->i_rwsem, corrupting its state when it is already held.
Fix it by calling unlock_new_inode() before d_instantiate(). This
matches what other filesystems do.
Fixes: 57397d86c6 ("f2fs: add inode operations for special inodes")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Currently f2fs's ->readpage() and ->readpages() assume that either the
data undergoes no postprocessing, or decryption only. But with
fs-verity, there will be an additional authenticity verification step,
and it may be needed either by itself, or combined with decryption.
To support this, store a 'struct bio_post_read_ctx' in ->bi_private
which contains a work struct, a bitmask of postprocessing steps that are
enabled, and an indicator of the current step. The bio completion
routine, if there was no I/O error, enqueues the first postprocessing
step. When that completes, it continues to the next step. Pages that
fail any postprocessing step have PageError set. Once all steps have
completed, pages without PageError set are set Uptodate, and all pages
are unlocked.
Also replace f2fs_encrypted_file() with a new function
f2fs_post_read_required() in places like direct I/O and garbage
collection that really should be testing whether the file needs special
I/O processing, not whether it is encrypted specifically.
This may also be useful for other future f2fs features such as
compression.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Currently, fscrypt provides fscrypt_decrypt_bio_pages() which decrypts a
bio's pages asynchronously, then unlocks them afterwards. But, this
assumes that decryption is the last "postprocessing step" for the bio,
so it's incompatible with additional postprocessing steps such as
authenticity verification after decryption.
Therefore, rename the existing fscrypt_decrypt_bio_pages() to
fscrypt_enqueue_decrypt_bio(). Then, add fscrypt_decrypt_bio() which
decrypts the pages in the bio synchronously without unlocking the pages,
nor setting them Uptodate; and add fscrypt_enqueue_decrypt_work(), which
enqueues work on the fscrypt_read_workqueue. The new functions will be
used by filesystems that support both fscrypt and fs-verity.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Replace 01.org URL with upstream linux-firmware repo URL.
We no longer release firmware to 01.org.
linux-firmware.git is the ultimate place to find
the i915 firmwares.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1525129168-529-1-git-send-email-anusha.srivatsa@intel.com
Normally, a socket can not be freed/reused unless all its TX packets
left qdisc and were TX-completed. However connect(AF_UNSPEC) allows
this to happen.
With commit fc59d5bdf1 ("pkt_sched: fq: clear time_next_packet for
reused flows") we cleared f->time_next_packet but took no special
action if the flow was still in the throttled rb-tree.
Since f->time_next_packet is the key used in the rb-tree searches,
blindly clearing it might break rb-tree integrity. We need to make
sure the flow is no longer in the rb-tree to avoid this problem.
Fixes: fc59d5bdf1 ("pkt_sched: fq: clear time_next_packet for reused flows")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit edd7ceb782 ("ipv6: Allow non-gateway ECMP for
IPv6").
Eric reported a division by zero in rt6_multipath_rebalance() which is
caused by above commit that considers identical local routes to be
siblings. The division by zero happens because a nexthop weight is not
set for local routes.
Revert the commit as it does not fix a bug and has side effects.
To reproduce:
# ip -6 address add 2001:db8::1/64 dev dummy0
# ip -6 address add 2001:db8::1/64 dev dummy1
Fixes: edd7ceb782 ("ipv6: Allow non-gateway ECMP for IPv6")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit says:
====================
r8169: series with further improvements
I thought I'm more or less done with the basic refactoring. But again
I stumbled across things that can be improved / simplified.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is basically the same as 6e74d1749a ("r8152: replace
get_protocol with vlan_get_protocol"). Use vlan_get_protocol
instead of duplicating the functionality.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interpreting a member of an u16 array as u32 may result in a misaligned
access. Also it's not really intuitive to define a mac address variable
as array of three u16 words. Therefore use an array of six bytes that
is properly aligned for 32 bit access.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>