When unbinding/removing the driver, we will run into the following warnings:
[ 259.655198] fec 400d1000.ethernet: 400d1000.ethernet supply phy not found, using dummy regulator
[ 259.665065] fec 400d1000.ethernet: Unbalanced pm_runtime_enable!
[ 259.672770] fec 400d1000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
[ 259.683062] fec 400d1000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: f2:3e:93:b7:29:c1
[ 259.696239] libphy: fec_enet_mii_bus: probed
Avoid these warnings by balancing the runtime PM calls during fec_drv_remove().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Allwinner H6 SoC has a CCU which has been largely rearranged.
Add support for it in the sunxi-ng CCU framework.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner H6 main CCU uses the internal oscillator of the SoC, which
is different with old SoCs' main CCU.
Add device tree binding for the Allwinner H6 main CCU.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
On the new Allwinner H6 SoC, multiple PLL's are NMP style clocks
(modelled as NKMP with no K) and have fixed post-dividers.
Add fixed post divider support to the NKMP style clocks.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Pull x86/pti updates from Thomas Gleixner:
"Another set of melted spectrum updates:
- Iron out the last late microcode loading issues by actually
checking whether new microcode is present and preventing the CPU
synchronization to run into a timeout induced hang.
- Remove Skylake C2 from the microcode blacklist according to the
latest Intel documentation
- Fix the VM86 POPF emulation which traps if VIP is set, but VIF is
not. Enhance the selftests to catch that kind of issue
- Annotate indirect calls/jumps for objtool on 32bit. This is not a
functional issue, but for consistency sake its the right thing to
do.
- Fix a jump label build warning observed on SPARC64 which uses 32bit
storage for the code location which is casted to 64 bit pointer w/o
extending it to 64bit first.
- Add two new cpufeature bits. Not really an urgent issue, but
provides them for both x86 and x86/kvm work. No impact on the
current kernel"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode: Fix CPU synchronization routine
x86/microcode: Attempt late loading only when new microcode is present
x86/speculation: Remove Skylake C2 from Speculation Control microcode blacklist
jump_label: Fix sparc64 warning
x86/speculation, objtool: Annotate indirect calls/jumps for objtool on 32-bit kernels
x86/vm86/32: Fix POPF emulation
selftests/x86/entry_from_vm86: Add test cases for POPF
selftests/x86/entry_from_vm86: Exit with 1 if we fail
x86/cpufeatures: Add Intel PCONFIG cpufeature
x86/cpufeatures: Add Intel Total Memory Encryption cpufeature
Pull x86 fix from Thomas Gleixner:
"A single fix for vmalloc_fault() which uses p*d_huge() unconditionally
whether CONFIG_HUGETLBFS is set or not. In case of CONFIG_HUGETLBFS=n
this results in a crash as p*d_huge() returns 0 in that case"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Fix vmalloc_fault to use pXd_large
Pull irq fixes from Thomas Gleixner:
"Three fixes for irq chip drivers:
- Make sure the allocations in the GIC-V3 ITS driver are large enough
to accomodate the interrupt space
- Fix a misplaced __iomem annotation which causes a splat of 26
sparse warnings
- Remove an unused function in the IMX GPCV2 driver which causes
build warnings"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/irq-imx-gpcv2: Remove unused function
irqchip/gic-v3-its: Ensure nr_ites >= nr_lpis
irqchip/gic-v3-its: Fix misplaced __iomem annotations
Pull EFI fix from Thomas Gleixner:
"A single fix to prevent partially initialized pointers in mixed mode
(64bit kernel on 32bit UEFI)"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/libstub/tpm: Initialize pointer variables to zero for mixed mode
Version 20180313.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This prepares the code for eventual removal of the original
style of deferred execution of the MLC.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This ensures that acpi_ev_fixed_event_detect() does not use fixed_status
and and fixed_enable as uninitialized variables.
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
lockups on POWER9.
* ARM: locking fix, reset fix, GICv2 multi-source SGI injection fix,
GICv2-on-v3 MMIO synchronization fix, make the console less verbose.
* x86: fix device passthrough on AMD SME.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJariCQAAoJEL/70l94x66D6j4H/iS51f1EFRjTXbM+/D0BxpOD
hTz3tiV4JNezwXkxm9FMr7e5sfONTsqZodzCeXbz9XRmb6lwkEIbaPC4G2ALJeBH
V1Gpy2NsoBNCaU6Ci7SGqs1PG7wmG1tGMkzgkUoi2mwJRbA7UfnPmL1bTRESc4/w
oYN5xPj1/bLYWnok2cEJevND2VUTy+/dazpm+9gZzHqeoBnRRhhNluLW11A7yi2U
mSxAZrCH8X9EejIEhU8jAah4PYZ9tP8TmvUcnAPYpNgDh2JH6tlkGAYSbpadiCvf
FJNhtev67uDL1jPzqQJLNo5Z04cg06M+9cYqrLD1q287LXsKs+LHXJY/AI56oIM=
=YHkv
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"PPC:
- fix bug leading to lost IPIs and smp_call_function_many() lockups
on POWER9
ARM:
- locking fix
- reset fix
- GICv2 multi-source SGI injection fix
- GICv2-on-v3 MMIO synchronization fix
- make the console less verbose.
x86:
- fix device passthrough on AMD SME"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Fix device passthrough when SME is active
kvm: arm/arm64: vgic-v3: Tighten synchronization for guests using v2 on v3
KVM: arm/arm64: vgic: Don't populate multiple LRs with the same vintid
KVM: arm/arm64: Reduce verbosity of KVM init log
KVM: arm/arm64: Reset mapped IRQs on VM reset
KVM: arm/arm64: Avoid vcpu_load for other vcpu ioctls than KVM_RUN
KVM: arm/arm64: vgic: Add missing irq_lock to vgic_mmio_read_pending
KVM: PPC: Book3S HV: Fix trap number return from __kvmppc_vcore_entry
Was acpi_gbl_parse_table_as_term_list, changed to:
acpi_gbl_execute_tables_as_methods.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fixing the ACPI_ERROR_NAMESPACE macros created an "unused variable"
compile error when ACPI_NO_ERROR_MESSAGES was defined. This commit
also fixes the above compilation errors by surrounding variables
meant for debugging inside a new ACPI_ERROR_ONLY macro.
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Changes the option to ignore package resolution errors into
a runtime option.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As the documentatuon above its declaration indicates, acpi_get_object_info()
is intended for early probe usage and as such should not call any methods
which may rely on op_regions, before this commit it was also calling _STA,
which on some systems does rely on op_regions.
Calling _STA before things are ready leads to errors such as these
(under Linux, on some hardware):
[ 0.123579] ACPI Error: No handler for Region [ECRM] (00000000ba9edc4c)
[generic_serial_bus] (20170831/evregion-166)
[ 0.123601] ACPI Error: Region generic_serial_bus (ID=9) has no handler
(20170831/exfldio-299)
[ 0.123618] ACPI Error: Method parse/execution failed
\_SB.I2C1.BAT1._STA, AE_NOT_EXIST (20170831/psparse-550)
End 2015 support for the _SUB method was removed for exactly the same
reason. Removing current_status from struct acpi_device_info only has a limited
impact. Within ACPICA it is only used by 2 debug messages, both
of which are modified to no longer print it with this commit.
Outside of ACPICA, there was one user in Linux, which has been patched to
no longer use current_status in Torvald's current master.
I've not checked if free_BSD or others are using the current_status field.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The implementation previously ignored null strings (""), but
these could be important, especially for debug.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fixes a single-object memory leak on a store-to-reference method
invocation. ACPICA BZ 1439.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After being enabled for the first time, the GPEs may have STS bits already
set. Setting EN bits is not sufficient to trigger the GPEs again, so this
patch polls GPEs after enabling them for the first time.
This is a cleaner version on top of the "GPE clear" fix generated according
to Mika's report and Rafael's original Linux based fix. Based on Linux
commit originated from Rafael J. Wysocki, fixed by Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is a risk that a GPE method/handler may be invoked twice. Let's
consider a case, both GPE0(RAW_HANDLER) and GPE1(_Exx) is triggered.
=======================================+=============================
IRQ handler (top-half) |IRQ polling
=======================================+=============================
acpi_ev_detect_gpe() |
LOCK() |
READ (GPE0-7 enable/status registers)|
^^^^^^^^^^^^ROOT CAUSE^^^^^^^^^^^^^^^|
Walk GPE0 |
UNLOCK() |LOCK()
Invoke GPE0 RAW_HANDLER |READ (GPE1 enable/status bit)
|acpi_ev_gpe_dispatch(irq=false)
| CLEAR (GPE1 enable bit)
| CLEAR (GPE1 status bit)
LOCK() |UNLOCK()
Walk GPE1 +=============================
acpi_ev_gpe_dispatch(irq=true) |IRQ polling (defer)
CLEAR (GPE1 enable bit) +=============================
CLEAR (GPE1 status bit) |acpi_ev_async_execute_gpe_method()
Walk others | Evaluate GPE1 _Exx
fi | acpi_ev_async_enable_gpe()
UNLOCK() | LOCK()
=======================================+ SET (GPE enable bit)
IRQ handler (bottom-half) | UNLOCK()
=======================================+
acpi_ev_async_execute_gpe_method() |
Evaluate GPE1 _Exx |
acpi_ev_async_enable_gpe() |
LOCK() |
SET (GPE1 enable bit) |
UNLOCK() |
=======================================+=============================
If acpi_ev_detect_gpe() is only invoked from the IRQ context, there won't be
more than one _Lxx/_Exx evaluations for one status bit flagging if the IRQ
handlers controlled by the underlying IRQ chip/driver (ex. APIC) are run in
serial. Note that, this is a known potential gap and we had an approach,
locking entire non-raw-handler processes in the top-half IRQ handler and
handling all raw-handlers out of the locked loop to be friendly to those
IRQ chip/driver. But the approach is too complicated while the issue is not
so real, thus ACPICA treated such issue (if any) as a parallelism/quality
issue of the underlying IRQ chip/driver to stop putting it on the radar.
Bug in link #1 is suspiciously reflecting the same cause, and if so, it can
also be fixed by this simpler approach.
But it will be no excuse an ACPICA problem now if ACPICA starts to poll
IRQs itself. In the changed scenario, _Exx will be evaluated from the task
context due to new ACPICA provided "polling after enabling GPEs" mechanism.
And the above figure uses edge-triggered GPEs demonstrating the possibility
of evaluating _Exx twice for one status bit flagging.
As a conclusion, there is now an increased chance of evaluating _Lxx/_Exx
more than once for one status bit flagging.
However this is still not a real problem if the _Lxx/_Exx checks the
underlying hardware IRQ reasoning and finally just changes the 2nd and the
follow-up evaluations into no-ops. Note that _Lxx should always be written
in this way as a level-trigger GPE could have it's status wrongly
duplicated by the underlying IRQ delivery mechanisms. But _Exx may have
very low quality BIOS by BIOS to trigger real issues. For example, trigger
duplicated button notifications.
To solve this issue, we need to stop reading a bunch of enable/status
register bits, but read only one GPE's enable/status bit. And GPE status
register's W1C nature ensures that acknowledging one GPE won't affect
another GPEs' status bits. Thus the hardware GPE architecture has already
provided us with the mechanism of implementing such parallelism.
So we can lock around one GPE handling process to achieve the parallelism:
1. If we can incorporate GPE enable bit check in detection and ensure the
atomicity of the following process (top-half IRQ handler):
READ (enable/status bit)
if (enabled && raised)
CLEAR (enable bit)
and handle the GPE after this process, we can ensure that we will only
invoke GPE handler once for one status bit flagging.
2. In addtion for edge-triggered GPEs, if we can ensure the atomicity of
the following process (top-half IRQ handler):
READ (enable/status bit)
if (enabled && raised)
CLEAR (enable bit)
CLEAR (status bit)
and handle the GPE after this process, we can ensure that we will only
invoke GPE handler once for one status bit flagging.
By doing a cleanup in this way, we can remove duplicate GPE handling code
and ensure that all logics are collected in 1 function. And the function
will be safe for both IRQ interrupt and IRQ polling, and will be safe for
us to release and re-acquire acpi_gbl_gpe_lock at any time rather than raw
handler only during the top-half IRQ handler. Lv Zheng.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196703 [#1]
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Unconditionally clearing ACPI IRQs during suspend/resume can lead to
unexpected IRQ losts. This patch fixes this issue by removing such IRQ
clearing code.
If this patch triggers regression, the regression should be in the GPE
handlers that cannot correctly determine some spurious triggered events as
no-ops. Please report any regression related to this commit to the ACPI
component on kernel bugzilla. Lv Zheng.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196249
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reported-and-tested-by: Eric Bakula-Davis <ericbakuladavis@gmail.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlqlyPEeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGNa0H/RIa/StQuYu/SBwa
JRqQFmkIsx+gG+FyamJrqGzRfyjounES8PbfyaN3cCrzYgeRwMp1U/bZW6/l5tkb
OjTtrCJ6CJaa21fC/7aqn3rhejHciKyk83EinMu5WjDpsQcaF2xKr3SaPa62Ja24
fhawKq3CnUa+OUuAbicVX8yn4viUB6x8FjSN/IWfp3Cs4IBR7SGxxD7A4MET9FbQ
5OOu0al8ly9QeCggTtJyk+cApeLfexEBTbUur9gm7GcH9jhUtJSyZCZsDJx6M2yb
CwdgF4fyk58c1fuHvTFb0AdUns55ba3nicybRHHMVbDpZIG9v4/M1yJETHHf5cD7
t3rFjrY=
=+Ldf
-----END PGP SIGNATURE-----
Merge tag 'v4.16-rc5' into devel
Linux 4.16-rc5 merged into the GPIO devel branch to resolve
a nasty conflict between fixes and devel in the RCAR driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Khalid Aziz says:
====================
Application Data Integrity feature introduced by SPARC M7
V12 changes:
This series is same as v10 and v11 and was simply rebased on 4.16-rc2
kernel and patch 11 was added to update signal delivery code to use the
new helper functions added by Eric Biederman. Can mm maintainers please
review patches 2, 7, 8 and 9 which are arch independent, and
include/linux/mm.h and mm/ksm.c changes in patch 10 and ack these if
everything looks good?
SPARC M7 processor adds additional metadata for memory address space
that can be used to secure access to regions of memory. This additional
metadata is implemented as a 4-bit tag attached to each cacheline size
block of memory. A task can set a tag on any number of such blocks.
Access to such block is granted only if the virtual address used to
access that block of memory has the tag encoded in the uppermost 4 bits
of VA. Since sparc processor does not implement all 64 bits of VA, top 4
bits are available for ADI tags. Any mismatch between tag encoded in VA
and tag set on the memory block results in a trap. Tags are verified in
the VA presented to the MMU and tags are associated with the physical
page VA maps on to. If a memory page is swapped out and page frame gets
reused for another task, the tags are lost and hence must be saved when
swapping or migrating the page.
A userspace task enables ADI through mprotect(). This patch series adds
a page protection bit PROT_ADI and a corresponding VMA flag
VM_SPARC_ADI. VM_SPARC_ADI is used to trigger setting TTE.mcd bit in the
sparc pte that enables ADI checking on the corresponding page. MMU
validates the tag embedded in VA for every page that has TTE.mcd bit set
in its pte. After enabling ADI on a memory range, the userspace task can
set ADI version tags using stxa instruction with ASI_MCD_PRIMARY or
ASI_MCD_ST_BLKINIT_PRIMARY ASI.
Once userspace task calls mprotect() with PROT_ADI, kernel takes
following overall steps:
1. Find the VMAs covering the address range passed in to mprotect and
set VM_SPARC_ADI flag. If address range covers a subset of a VMA, the
VMA will be split.
2. When a page is allocated for a VA and the VMA covering this VA has
VM_SPARC_ADI flag set, set the TTE.mcd bit so MMU will check the
vwersion tag.
3. Userspace can now set version tags on the memory it has enabled ADI
on. Userspace accesses ADI enabled memory using a virtual address that
has the version tag embedded in the high bits. MMU validates this
version tag against the actual tag set on the memory. If tag matches,
MMU performs the VA->PA translation and access is granted. If there is a
mismatch, hypervisor sends a data access exception or precise memory
corruption detected exception depending upon whether precise exceptions
are enabled or not (controlled by MCDPERR register). Kernel sends
SIGSEGV to the task with appropriate si_code.
4. If a page is being swapped out or migrated, kernel must save any ADI
tags set on the page. Kernel maintains a page worth of tag storage
descriptors. Each descriptors pointsto a tag storage space and the
address range it covers. If the page being swapped out or migrated has
ADI enabled on it, kernel finds a tag storage descriptor that covers the
address range for the page or allocates a new descriptor if none of the
existing descriptors cover the address range. Kernel saves tags from the
page into the tag storage space descriptor points to.
5. When the page is swapped back in or reinstantiated after migration,
kernel restores the version tags on the new physical page by retrieving
the original tag from tag storage pointed to by a tag storage descriptor
for the virtual address range for new page.
User task can disable ADI by calling mprotect() again on the memory
range with PROT_ADI bit unset. Kernel clears the VM_SPARC_ADI flag in
VMAs, merges adjacent VMAs if necessary, and clears TTE.mcd bit in the
corresponding ptes.
IOMMU does not support ADI checking. Any version tags embedded in the
top bits of VA meant for IOMMU, are cleared and replaced with sign
extension of the first non-version tag bit (bit 59 for SPARC M7) for
IOMMU addresses.
This patch series adds support for this feature in 11 patches:
Patch 1/11
Tag mismatch on access by a task results in a trap from hypervisor as
data access exception or a precide memory corruption detected
exception. As part of handling these exceptions, kernel sends a
SIGSEGV to user process with special si_code to indicate which fault
occurred. This patch adds three new si_codes to differentiate between
various mismatch errors.
Patch 2/11
When a page is swapped or migrated, metadata associated with the page
must be saved so it can be restored later. This patch adds a new
function that saves/restores this metadata when updating pte upon a
swap/migration.
Patch 3/11
SPARC M7 processor adds new fields to control registers to support ADI
feature. It also adds a new exception for precise traps on tag
mismatch. This patch adds definitions for the new control register
fields, new ASIs for ADI and an exception handler for the precise trap
on tag mismatch.
Patch 4/11
New hypervisor fault types were added by sparc M7 processor to support
ADI feature. This patch adds code to handle these fault types for data
access exception handler.
Patch 5/11
When ADI is in use for a page and a tag mismatch occurs, processor
raises "Memory corruption Detected" trap. This patch adds a handler
for this trap.
Patch 6/11
ADI usage is governed by ADI properties on a platform. These
properties are provided to kernel by firmware. Thsi patch adds new
auxiliary vectors that provide these values to userpsace.
Patch 7/11
arch_validate_prot() is used to validate the new protection bits asked
for by the userspace app. Validating protection bits may need the
context of address space the bits are being applied to. One such
example is PROT_ADI bit on sparc processor that enables ADI protection
on an address range. ADI protection applies only to addresses covered
by physical RAM and not other PFN mapped addresses or device
addresses. This patch adds "address" to the parameters being passed to
arch_validate_prot() to provide that context.
Patch 8/11
When protection bits are changed on a page, kernel carries forward all
protection bits except for read/write/exec. Additional code was added
to allow kernel to clear PKEY bits on x86 but this requirement to
clear other bits is not unique to x86. This patch extends the existing
code to allow other architectures to clear any other protection bits
as well on protection bit change.
Patch 9/11
When a processor supports additional metadata on memory pages, that
additional metadata needs to be copied to new memory pages when those
pages are moved. This patch allows architecture specific code to
replace the default copy_highpage() routine with arch specific
version that copies the metadata as well besides the data on the page.
Patch 10/11
This patch adds support for a user space task to enable ADI and enable
tag checking for subsets of its address space. As part of enabling
this feature, this patch adds to support manipulation of precise
exception for memory corruption detection, adds code to save and
restore tags on page swap and migration, and adds code to handle ADI
tagged addresses for DMA.
Patch 11/11
Update signal delivery code in arch/sparc/kernel/traps_64.c to use
the new helper function force_sig_fault() added by commit
f8ec66014f ("signal: Add send_sig_fault and force_sig_fault").
Changelog v12:
- Rebased to 4.16-rc2
- Added patch 11 to update signal delivery functions
Changelog v11:
- Rebased to 4.15
Changelog v10:
- Patch 1/10: Updated si_codes definitions for SEGV to match 4.14
- Patch 2/10: No changes
- Patch 3/10: Updated copyright
- Patch 4/10: No changes
- Patch 5/10: No changes
- Patch 6/10: Updated copyright
- Patch 7/10: No changes
- Patch 8/10: No changes
- Patch 9/10: No changes
- Patch 10/10: Added code to return from kernel path to set
PSTATE.mcde if kernel continues execution in another thread
(Suggested by Anthony)
Changelog v9:
- Patch 1/10: No changes
- Patch 2/10: No changes
- Patch 3/10: No changes
- Patch 4/10: No changes
- Patch 5/10: No changes
- Patch 6/10: No changes
- Patch 7/10: No changes
- Patch 8/10: No changes
- Patch 9/10: New patch
- Patch 10/10: Patch 9 from v8. Added code to copy ADI tags when
pages are migrated. Updated code to detect overflow and underflow
of addresses when allocating tag storage.
Changelog v8:
- Patch 1/9: No changes
- Patch 2/9: Fixed and erroneous "}"
- Patch 3/9: Minor print formatting change
- Patch 4/9: No changes
- Patch 5/9: No changes
- Patch 6/9: Added AT_ADI_UEONADI back
- Patch 7/9: Added addr parameter to powerpc arch_validate_prot()
- Patch 8/9: No changes
- Patch 9/9:
- Documentation updates
- Added an IPI on mprotect(...PROT_ADI...) call and
restore of TSTATE.MCDE on context switch
- Removed restriction on enabling ADI on read-only
memory
- Changed kzalloc() for tag storage to use GFP_NOWAIT
- Added code to handle overflow and underflow when
allocating tag storage
- Replaced sun_m7_patch_1insn_range() with
sun4v_patch_1insn_range()
- Added membar after restoring ADI tags in
copy_user_highpage()
Changelog v7:
- Patch 1/9: No changes
- Patch 2/9: Updated parameters to arch specific swap in/out
handlers
- Patch 3/9: No changes
- Patch 4/9: new patch split off from patch 4/4 in v6
- Patch 5/9: new patch split off from patch 4/4 in v6
- Patch 6/9: new patch split off from patch 4/4 in v6
- Patch 7/9: new patch
- Patch 8/9: new patch
- Patch 9/9:
- Enhanced arch_validate_prot() to enable ADI only on
writable addresses backed by physical RAM
- Added support for saving/restoring ADI tags for each
ADI block size address range on a page on swap in/out
- copy ADI tags on COW
- Updated values for auxiliary vectors to not conflict
with values on other architectures to avoid conflict
in glibc
- Disable same page merging on ADI enabled pages
- Enable ADI only on writable addresses backed by
physical RAM
- Split parts of patch off into separate patches
Changelog v6:
- Patch 1/4: No changes
- Patch 2/4: No changes
- Patch 3/4: Added missing nop in the delay slot in
sun4v_mcd_detect_precise
- Patch 4/4: Eliminated instructions to read and write PSTATE
as well as MCDPER and PMCDPER on every access to userspace
addresses by setting PSTATE and PMCDPER correctly upon entry
into kernel
Changelog v5:
- Patch 1/4: No changes
- Patch 2/4: Replaced set_swp_pte_at() with new architecture
functions arch_do_swap_page() and arch_unmap_one() that
suppoprt architecture specific actions to be taken on page
swap and migration
- Patch 3/4: Fixed indentation issues in assembly code
- Patch 4/4:
- Fixed indentation issues and instrcuctions in assembly
code
- Removed CONFIG_SPARC64 from mdesc.c
- Changed to maintain state of MCDPER register in thread
info flags as opposed to in mm context. MCDPER is a
per-thread state and belongs in thread info flag as
opposed to mm context which is shared across threads.
Added comments to clarify this is a lazily maintained
state and must be updated on context switch and
copy_process()
- Updated code to use the new arch_do_swap_page() and
arch_unmap_one() functions
Testing:
- All functionality was tested with 8K normal pages as well as hugepages
using malloc, mmap and shm.
- Multiple long duration stress tests were run using hugepages over 2+
months. Normal pages were tested with shorter duration stress tests.
- Tested swapping with malloc and shm by reducing max memory and
allocating three times the available system memory by active processes
using ADI on allocated memory. Ran through multiple hours long runs of
this test.
- Tested page migration with malloc and shm by migrating data pages of
active ADI test process using migratepages, back and forth between two
nodes every few seconds over an hour long run. Verified page migration
through /proc/<pid>/numa_maps.
- Tested COW support using test that forks children that read from
ADI enabled pages shared with parent and other children and write to
them as well forcing COW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f8ec66014f ("signal: Add send_sig_fault and force_sig_fault")
added new helper functions to streamline signal delivery. This patch
updates signal delivery for new/updated handlers for ADI related
exceptions to use the helper function.
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Khalid Aziz <khalid@gonehiking.org>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ADI is a new feature supported on SPARC M7 and newer processors to allow
hardware to catch rogue accesses to memory. ADI is supported for data
fetches only and not instruction fetches. An app can enable ADI on its
data pages, set version tags on them and use versioned addresses to
access the data pages. Upper bits of the address contain the version
tag. On M7 processors, upper four bits (bits 63-60) contain the version
tag. If a rogue app attempts to access ADI enabled data pages, its
access is blocked and processor generates an exception. Please see
Documentation/sparc/adi.txt for further details.
This patch extends mprotect to enable ADI (TSTATE.mcde), enable/disable
MCD (Memory Corruption Detection) on selected memory ranges, enable
TTE.mcd in PTEs, return ADI parameters to userspace and save/restore ADI
version tags on page swap out/in or migration. ADI is not enabled by
default for any task. A task must explicitly enable ADI on a memory
range and set version tag for ADI to be effective for the task.
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Khalid Aziz <khalid@gonehiking.org>
Reviewed-by: Anthony Yznaga <anthony.yznaga@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some architectures can support metadata for memory pages and when a
page is copied, its metadata must also be copied. Sparc processors
from M7 onwards support metadata for memory pages. This metadata
provides tag based protection for access to memory pages. To maintain
this protection, the tag data must be copied to the new page when a
page is migrated across NUMA nodes. This patch allows arch specific
code to override default copy_highpage() and copy metadata along
with page data upon migration.
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Khalid Aziz <khalid@gonehiking.org>
Reviewed-by: Anthony Yznaga <anthony.yznaga@oracle.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When protection bits are changed on a VMA, some of the architecture
specific flags should be cleared as well. An examples of this are the
PKEY flags on x86. This patch expands the current code that clears
PKEY flags for x86, to support similar functionality for other
architectures as well.
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Khalid Aziz <khalid@gonehiking.org>
Reviewed-by: Anthony Yznaga <anthony.yznaga@oracle.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A protection flag may not be valid across entire address space and
hence arch_validate_prot() might need the address a protection bit is
being set on to ensure it is a valid protection flag. For example, sparc
processors support memory corruption detection (as part of ADI feature)
flag on memory addresses mapped on to physical RAM but not on PFN mapped
pages or addresses mapped on to devices. This patch adds address to the
parameters being passed to arch_validate_prot() so protection bits can
be validated in the relevant context.
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Khalid Aziz <khalid@gonehiking.org>
Reviewed-by: Anthony Yznaga <anthony.yznaga@oracle.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ADI feature on M7 and newer processors has three important properties
relevant to userspace apps using ADI capabilities - (1) Size of block of
memory an ADI version tag applies to, (2) Number of uppermost bits in
virtual address used to encode ADI tag, and (3) The value M7 processor
will force the ADI tags to if it detects uncorrectable error in an ADI
tagged cacheline. Kernel can retrieve these properties for a platform
through machine description provided by the firmware. This patch adds
code to retrieve these properties and report them to userspace through
auxiliary vectors.
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Khalid Aziz <khalid@gonehiking.org>
Reviewed-by: Anthony Yznaga <anthony.yznaga@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
M7 and newer processors add a "Memory corruption Detected" trap with
the addition of ADI feature. This trap is vectored into kernel by HV
through resumable error trap with error attribute for the resumable
error set to 0x00000800.
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Khalid Aziz <khalid@gonehiking.org>
Reviewed-by: Anthony Yznaga <anthony.yznaga@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ADI (Application Data Integrity) feature on M7 and newer processors
adds new fault types for hypervisor - Invalid ASI and MCD disabled.
This patch expands data access exception handler to handle these
faults.
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Khalid Aziz <khalid@gonehiking.org>
Reviewed-by: Anthony Yznaga <anthony.yznaga@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SPARC M7 processor adds new control register fields, ASIs and a new
trap to support the ADI (Application Data Integrity) feature. This
patch adds definitions for these register fields, ASIs and a handler
for the new precise memory corruption detected trap.
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Khalid Aziz <khalid@gonehiking.org>
Reviewed-by: Anthony Yznaga <anthony.yznaga@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a processor supports special metadata for a page, for example ADI
version tags on SPARC M7, this metadata must be saved when the page is
swapped out. The same metadata must be restored when the page is swapped
back in. This patch adds two new architecture specific functions -
arch_do_swap_page() to be called when a page is swapped in, and
arch_unmap_one() to be called when a page is being unmapped for swap
out. These architecture hooks allow page metadata to be saved if the
architecture supports it.
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Khalid Aziz <khalid@gonehiking.org>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Reviewed-by: Anthony Yznaga <anthony.yznaga@oracle.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
SPARC M7 processor introduces a new feature - Application Data
Integrity (ADI). ADI allows MMU to catch rogue accesses to memory.
When a rogue access occurs, MMU blocks the access and raises an
exception. In response to the exception, kernel sends the offending
task a SIGSEGV with si_code that indicates the nature of exception.
This patch adds three new signal codes specific to ADI feature:
1. ADI is not enabled for the address and task attempted to access
memory using ADI
2. Task attempted to access memory using wrong ADI tag and caused
a deferred exception.
3. Task attempted to access memory using wrong ADI tag and caused
a precise exception.
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Khalid Aziz <khalid@gonehiking.org>
Reviewed-by: Anthony Yznaga <anthony.yznaga@oracle.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
batadv_check_unicast_ttvn may redirect a packet to itself or another
originator. This involves rewriting the ttvn and the destination address in
the batadv unicast header. These field were not yet pulled (with skb rcsum
update) and thus any change to them also requires a change in the receive
checksum.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Fixes: a73105b8d4 ("batman-adv: improved client announcement mechanism")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
In adis16201_read_raw() adjust an argument to match an open parentheses
using tabs and spaces.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Prefer reverse christmas tree ordering of declarations to improve
readability.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use sign_extned32() for 32 bit sign extending rather than hard coding.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Clarify the conversion and formation of resultant data in the
adis16201_read_raw() with sufficient comments and remove the unnecessary
comments.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Group register definitions with its register field bits to improve
readability and easy identification. A small comment is also added to
denote the purpose/functionality of the grouped register definitions.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add a _REG suffix to distinguish between registers and the register bit
fileds.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove few unnecessary comments since the macro definitions clearly
justify their purpose.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rename the macro definitions with suitable names specifying their
purpose.
* ADIS16201_STARTUP_DELAY_MS: Remove the comment specifying the delay in
microseconds and rename it with addtition of _MS suffix.
* ADIS16201_MSC_CTRL_ACTIVE_DATA_RDY_HIGH: Rename the macro to make it
similar to other misc control registers which denotes the data ready
polarity.
* ADIS16201_DIAG_STAT_FLASH_UPT_FAIL_BIT: Rename to denote it is a
failure bit.
* ADIS16201_GLOB_CMD_FACTORY_RESET: Remove ambiguous _CAL suffix and add
_RESET suffix instead to denote factory reset command.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
if device_register() returned an error! Always use put_device()
to give up the reference initialized. unregister device for
other return error.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
if device_register() returned an error! Always use put_device()
to give up the reference initialized. And unregister device for
other return error.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Handle polled interrupts correctly when loading the module.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 294d711ee8 ("net: dsa: mv88e6xxx: Poll when no interrupt defined")
Signed-off-by: David S. Miller <davem@davemloft.net>