These clocks are used by PCIe lanes, but we're missing from the
definition.
Suggested-by: Charalampos Mitrodimas <charmitro@posteo.net>
Signed-off-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://patch.msgid.link/20260304-rk3568-bri-r2-pro-fix-pcie-v4-1-37abd7ba29d0@ixit.cz
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The mphy reset signal is used to reset the physical adapter. Resetting
other components while leaving the mphy unreset may occasionally prevent
the UFS controller from successfully linking up with the device.
This addresses an intermittent hardware bug where the UFS link fails to
establish under specific timing conditions with certain chips. While
difficult to reproduce initially, this issue was consistently observed in
downstream testing and requires explicit mphy reset control for full
stability.
Fixes: c75e5e010f ("scsi: arm64: dts: rockchip: Add UFS support for RK3576 SoC")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://patch.msgid.link/1773277913-29580-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable the One Time Programmable Controller (OTPC) in RK3528 and add
an initial nvmem fixed layout.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260312213019.13965-4-heiko@sntech.de
Enable the One Time Programmable Controller (OTPC) in RK356x and add
an initial nvmem fixed layout.
Tested-by: Diederik de Haas <diederik@cknow-tech.com> # NanoPi R5S, PineNote
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260312213019.13965-3-heiko@sntech.de
Add supports-clkreq and the corresponding pinmux configurations for PCIe
ASPM L1 substates on the Rock 5B, 5B+ and 5T.
The supports-clkreq flag informs the PCIe controller that the hardware
routing for the CLKREQ# sideband signal is present. This enables support
for PCIe ASPM (Active State Power Management) L1 substates, allowing for
better power efficiency.
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://patch.msgid.link/20260316073621.39027-1-linux.amoon@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Provide aliases for the SD and eMMC interfaces, so that the operating
system can assign stable interface names.
On Linux this is only relevant when booting without partition UUID
based root device identification, e.g. when booting without an
initramfs. In that case booting with e.g. root=/dev/mmcblk0p2 is
unreliable without this patch as the device numbers changed based
on device probe order.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://patch.msgid.link/20260317-sige5-mmc-aliases-v1-1-ee93a1571802@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for all six SPDIF transmitters found in the RK3576.
The nodes have been taken over from the BSP kernel and checked
against the TRM (power domain descriptions from chapter 6.3.2,
addresses from "Table 1-1 Address Mapping", interrupt from
"Table 1-3 RK3576 Interrupt Connection List" (TRM numbers are
off by 32 due to SGI/PPI not being numbered separately). The
TRM lacks a proper clock tree, but fortunately are quite obvious
for the SPDIF IP.
Note, that the RK3576 also has 3 SPDIF receivers, which need their
own binding and are not handled in this patch.
A typical use case for the SPDIF transmitters is audio support for
the Displayport (DP) controller. DP requires inserting PCUV control
bits, which requires software support when using I2S. The SPDIF IP
can add it automatically and thus is preferred.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://patch.msgid.link/20260316-rk3576-spdif-v1-2-acb75088b560@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Khadas Edge 2L is a single board computer based on the Rockchip
RK3576 SoC.
Add basic device tree support for this board. Currently, only eMMC
and UART are enabled, allowing the board to boot into a basic Linux
system via the serial console.
Signed-off-by: Gray Huang <gray.huang@wesion.com>
Link: https://patch.msgid.link/20260317090731.600787-3-gray.huang@wesion.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Gameforce Ace's joystick axes were set incorrectly initially,
getting the X/Y and RX/RY axes backwards. Additionally, correct the
RY axis so that it is inverted.
All axes tested with evtest and outputting correct values.
Fixes: 4e946c447a ("arm64: dts: rockchip: Add GameForce Ace")
Reported-by: sydarn <sydarn@proton.me>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://patch.msgid.link/20260310134919.550023-1-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Correct the regulator providing power to the PWM controlled fan.
Without this fix the fan only runs when the audio path is playing
audio (because the speaker amplifier and PWM fan share the same
regulator).
Fixes: 4e946c447a ("arm64: dts: rockchip: Add GameForce Ace")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://patch.msgid.link/20260310134648.550006-1-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This reverts commit bdc4d388c6.
While Beelink A1 mostly follows the high-end RK3328 reference design,
it does not in fact have the S/PDIF connector, only HDMI and a 3.5mm
jack for the analog audio/TV codecs - the tiny form factor literally
doesn't have room to fit more!
Cc: Christian Hewitt <christianshewitt@gmail.com>
Cc: Alex Bee <knaerzche@gmail.com>
Fixes: bdc4d388c6 ("arm64: dts: rockchip: add SPDIF audio to Beelink A1")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://patch.msgid.link/0af77a02c2b0806d4ca72066392a5453fcc89a8f.1767111968.git.robin.murphy@arm.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The AP6212 WiFi/BT module on the LCKFB TaiShan Pi (RK3566) is prone to
communication timeouts and reset failures (error -110) when operating at
3 Mbps.
This patch stabilizes the Bluetooth interface by:
1. Updating the compatible string to 'brcm,bcm43430a1-bt' to better reflect
the actual chip revision used in the AP6212 module.
2. Lowering the maximum UART baud rate from 3,000,000 to 1,500,000 bps.
Tests show that 1.5 Mbps is the reliable upper limit for this board's
UART configuration, eliminating the initialization timeouts.
Fixes: 251e5ade9b ("arm64: dts: rockchip: add dts for LCKFB Taishan Pi RK3566")
Signed-off-by: Ming Wang <wangming5719@gmail.com>
Link: https://patch.msgid.link/20260206090453.1041919-1-wming126@126.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Digital Video Port (DVP, the 16-bit variant) of the RK3568 VICAP
is broken out to the PF5 mainboard expansion header.
Enable it in the device tree overlay for the WolfVision PF5 IO
Expander board.
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Reviewed-by: Gerald Loacker <gerald.loacker@wolfvision.net>
Tested-by: Gerald Loacker <gerald.loacker@wolfvision.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Michael Riesch <michael.riesch@collabora.com>
Link: https://patch.msgid.link/20260313-wv-io-expander-vicap-v1-1-11001fb3b744@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The GPU is most useful when used together with the EBC on the PineNote,
which is not yet described. But there's no reason not to define the GPU
already as the hardware is present and could be used without the EBC.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Diederik de Haas <diederik@cknow-tech.com>
Link: https://patch.msgid.link/20260305120620.173600-1-diederik@cknow-tech.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The hardware PU/PD config of the pin after reset is to pull-up and on
Jaguar this will also keep the device in reset until the driver actually
enables the pin. So restore this boot pull-up config of the pin on Jaguar
instead of setting it to pull-none.
Suggested-by: Quentin Schulz <quentin.schulz@cherry.de>
Fixes: 0ec7e10963 ("arm64: dts: rockchip: add PCIe3 support on rk3588-jaguar")
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://patch.msgid.link/20260210080303.680403-5-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
While specific driver in the Linux-Kernel handles GPIOs gracefully without
matching pinctrl entries, this might not be true for other operating
systems. So having pinctrl entries makes the hardware-description
more complete.
The somewhat similar rk3588-jaguar board has a pinctrl entry already,
so also add one for rk3588-tiger.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Link: https://patch.msgid.link/20260210080303.680403-4-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Using a combination of fixed clock and gpio-gate clock works but does
not describe the actual hardware. Use the gated-fixed-clock binding
to describe this in a nicer way.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://patch.msgid.link/20260210080303.680403-3-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Using a combination of fixed clock and gpio-gate clock works but does
not describe the actual hardware. Use the gated-fixed-clock binding
to describe this in a nicer way.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://patch.msgid.link/20260210080303.680403-2-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The PineNote has a single cell 4000mAh battery which can be charged via
the rk817 PMIC.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Co-developed-by: Maximilian Weigand <mweigand@mweigand.net>
Signed-off-by: Maximilian Weigand <mweigand@mweigand.net>
Signed-off-by: Diederik de Haas <diederik@cknow-tech.com>
Link: https://patch.msgid.link/20260224170531.516392-1-diederik@cknow-tech.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
In rk3576.dtsi, sdmmc0_pwren is configured as part of the sdmmc pinctrl.
However, on the rk3576 evb2 board, sdmmc0_pwren is used as the regulator
for vmmc-supply. Therefore, we need to reassign the sdmmc pinctrl and
remove sdmmc0_pwren to avoid conflicts.
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 86a82f7a7e ("arm64: dts: rockchip: Add rk3576 evb2 board")
Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Link: https://patch.msgid.link/20260226102052.63-1-kernel@airkyi.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The EDP_HOTPLUG pin is optional, and muxed with other functions (notably
HDMI CEC), so move its selection from the SoC DTSI to the boards which
apparently want it, namely those which enable eDP without "force-hpd".
By the same token we drop it from Pinebook Pro, which already uses
"force-hpd", and according to the schematics does not have the pin wired
at all.
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://patch.msgid.link/c7d972d07875241805db8659305b26bd694867d4.1769191673.git.robin.murphy@arm.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
TS433 devices received a board revision adding gpios for per hard-disk
presence-detection and power-control. These boards have a PCB-id of at
least 13 which can be read from an EEPROM.
The presence detection is not really necessary and there are also no
existing bindings for doing something with it. So add them as gpio hog
to at least document them and allow its state to be read from debugfs.
The power-control is modelled as regulator, with connected to the
RK3568's SATA controller as target-supply.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260201191804.41421-5-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
TS233 devices received a board revision adding gpios for per hard-disk
presence-detection and power-control. These boards have a PCB-id of at
least 12 (mainboard) and 11 (backplane), which can be read from an EEPROM.
The presence detection is not really necessary and there are also no
existing bindings for doing something with it. So add them as gpio hogs
to at least document them and allow their state to be read from debugfs.
The power-control is modelled as regulators, with the hdd1+hdd2 variants
connected to the RK3568's SATA controllers as target-supplies.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260201191804.41421-4-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
TS433 devices received a board revision adding gpios for per hard-disk
presence-detection and power-control. These board have a PCB-id of at
least 12 (mainboard) and 10 (backplane), which can be read from an EEPROM.
The presence detection is not really necessary and there are also no
existing bindings for doing something with it. So add them as gpio hogs
to at least document them and allow their state to be read from debugfs.
The power-control is modelled as regulators, with the hdd1+hdd2 variants
connected to the RK3568's SATA controllers as target-supplies. The
JMicron AHCI controller on PCIe didn't have bindings for that, I could
find, so they get an always-on state for now.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260201191804.41421-3-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The SATA controllers on RK356x are identical to the ones found on RK3588,
but don't yet provide a port sub-node. Per the datasheet the RK356x also
supports the fbscp capability and has the same queue maximums.
So add port sub-nodes to both sata controllers on RK356x, and move the
phy properties to it. Also add phandles to the ports, so that boards can
add their target-supply when available.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260201191804.41421-2-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for the two Awinic aw87391 audio amplifiers used in the
Anbernic RG-DS. These amplifiers require a specific init sequence to
start which is usually provided by a firmware file, but in our case
the manufacturer only provided the sequence. As a result, we hard-code
a device specific compatible.
Additionally, add support for the VDD regulator used to power both
amplifiers. Note that the amps can accept and respond to i2c commands
even without regulator power (perhaps due to a secondary power source)
but cannot play audio.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://patch.msgid.link/20260128174608.1498-4-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The power domains pd_rkvdec0/1 and pd_venc0/1 depend on two voltage
supplies, vdd_vdenc_s0 and vdd_vdenc_mem_s0. These supplies might be
missing or cause probe deferral. Since the Rockchip power domain
management code currently supports managing only one power supply, and
both supplies belong to the same PMIC (making it highly unlikely for
one to be available while the other is not), a practical solution
is implemented.
Both supplies are configured with the boot-on and always-on properties.
Only one of them is assigned as the domain-supply for pd_rkvdec0/1 and
pd_venc0/1. This allows the power domain code to perform a nominal enable
operation on this single supply, thereby successfully acquiring a
reference to both supplies (as they are from the same PMIC). The system
then relies on their boot-on and always-on flags to maintain the correct
state.
Crucially, this approach handles cases like probe deferral correctly:
if the PMIC is not yet ready, enabling the power domain will be deferred
until the necessary supplies become available.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://patch.msgid.link/1770950113-19802-2-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The OneThing Edge Cube (OEC) series features the RK3566 SoC, 8GB
eMMC storage, and supports one SATA interface, one Gigabit Ethernet
port, and one USB 3.0 port.
Other than the difference in RAM capacity, the OEC and OEC-turbo are
identical in all other specifications.
Specification:
- Rockchip RK3566
- LPDDR4X 2GB (OEC) / 4GB (OEC-turbo)
- eMMC 8GB
- Gigabit Ethernet port x 1
- USB 3.0 port x 1
- USB-C 2.0 port x 1
- 12V DC Power supply
- SATA 3.0 connector x 1
These devices do not have a PMIC, and their hardware circuit design
is highly similar to that of the rk3566-box-demo[1]. Hardware schematics
are not available at this time, with the vendor firmware dts available
for reference[2].
Ethernet, USB 3.0 and SATA 3.0 ports tested, all working well.
[1] https://elixir.bootlin.com/linux/v6.18.6/source/arch/arm64/boot/dts/rockchip/rk3566-box-demo.dts
[2] https://archive.org/download/wxy-oec-RK3566-4G-dump/wxy-oec-RK3566-4G-dump.dts
Signed-off-by: Jun Yan <jerrysteve1101@gmail.com>
Link: https://patch.msgid.link/20260214021719.620752-4-jerrysteve1101@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add devicetree binding for the OneThing OEC and OEC-turbo
The OneThing Edge Cube (OEC) series features the RK3566 SoC, 8GB
eMMC storage, and supports one SATA interface, one Gigabit Ethernet
port, and one USB 3.0 port.
Among the lineup, the standard OEC model comes with 2GB of RAM, while
the OEC-turbo features 4GB of RAM; The rest of the specifications are
identical.
The OneThing Edge Cube series (shipping with the vendor firmware) is
originally designed as a PCDN (P2P Content Delivery Network) device.
Signed-off-by: Jun Yan <jerrysteve1101@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20260214021719.620752-3-jerrysteve1101@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The DisplayPort on rk3576 is compliant with DisplayPort Specification
Version 1.4 with MST support, and share the USBDP combo PHY with USB 3.1
OTG0 controller.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://patch.msgid.link/20260206010421.443605-6-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
- Fix a build error on parisc
- Remove the non-large-folio-aware function fsverity_verify_page()
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQSacvsUNc7UX4ntmEPzXCl4vpKOKwUCaZtg+xQcZWJpZ2dlcnNA
a2VybmVsLm9yZwAKCRDzXCl4vpKOKwQ+AQCiXEYAibl3vHRgQo7qEPCC5or4FtkF
HZ0ERRArhsU17AD/TKHE/AJkyFrwK4rGTb6I9Wi1OXnpG7jihZlYjj03Ag4=
=CUql
-----END PGP SIGNATURE-----
Merge tag 'fsverity-for-linus' of git://git.kernel.org/pub/scm/fs/fsverity/linux
Pull fsverity fixes from Eric Biggers:
- Fix a build error on parisc
- Remove the non-large-folio-aware function fsverity_verify_page()
* tag 'fsverity-for-linus' of git://git.kernel.org/pub/scm/fs/fsverity/linux:
fsverity: fix build error by adding fsverity_readahead() stub
fsverity: remove fsverity_verify_page()
f2fs: make f2fs_verify_cluster() partially large-folio-aware
f2fs: remove unnecessary ClearPageUptodate in f2fs_verify_cluster()
Fix a big endian specific issue in the PPC64-optimized AES code.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQSacvsUNc7UX4ntmEPzXCl4vpKOKwUCaZtiphQcZWJpZ2dlcnNA
a2VybmVsLm9yZwAKCRDzXCl4vpKOK/z2AQD1j15Ao3iDW3yBSyTS+tFJaRUVDtjg
bNostoNJAjMM9wD/X0oAnt95WTNkdHexs+2aMzQ4ULKFRcwQrUTarKx7IgY=
=Dmfx
-----END PGP SIGNATURE-----
Merge tag 'libcrypto-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull crypto library fix from Eric Biggers:
"Fix a big endian specific issue in the PPC64-optimized AES code"
* tag 'libcrypto-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux:
lib/crypto: powerpc/aes: Fix rndkey_from_vsx() on big endian CPUs
Stephen retired and stepped back from -next maintainership, update his
entry in CREDITS to recognise his 18 years of hard work making it what
it is today and all the impact it's had on our development process.
Also update to his current GnuPG key while we're here.
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: SeongJae Park <sj@kernel.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The x509 public key code gained a dependency on the sha256 hash
implementation, causing a rare link time failure in randconfig
builds:
arm-linux-gnueabi-ld: crypto/asymmetric_keys/x509_public_key.o: in function `x509_get_sig_params':
x509_public_key.c:(.text.x509_get_sig_params+0x12): undefined reference to `sha256'
arm-linux-gnueabi-ld: (sha256): Unknown destination type (ARM/Thumb) in crypto/asymmetric_keys/x509_public_key.o
x509_public_key.c:(.text.x509_get_sig_params+0x12): dangerous relocation: unsupported relocation
Select the necessary library code from Kconfig.
Fixes: 2c62068ac8 ("x509: Separately calculate sha256 for blacklist")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Align to the commit bf4afc53b7 ("Convert 'alloc_obj' family to use the
new default GFP_KERNEL argument") update the 'kmalloc_obj' declaration
for userspace to fix below compile error:
In file included from arch/arm/boot/compressed/../../../../lib/decompress_unxz.c:241,
from arch/arm/boot/compressed/decompress.c:56:
arch/arm/boot/compressed/../../../../lib/xz/xz_dec_stream.c: In function 'xz_dec_init':
arch/arm/boot/compressed/../../../../lib/xz/xz_dec_stream.c:787:28: error: implicit declaration of function 'kmalloc_obj'; did you mean 'kmalloc'? [-Wimplicit-function-declaration]
787 | struct xz_dec *s = kmalloc_obj(*s);
| ^~~~~~~~~~~
| kmalloc
Signed-off-by: Haiyue Wang <haiyuewa@163.com>
Fixes: 69050f8d6d ("treewide: Replace kmalloc with kmalloc_obj for non-scalar types")
Fixes: bf4afc53b7 ("Convert 'alloc_obj' family to use the new default GFP_KERNEL argument")
Reviewed-by: Kees Cook <kees@kernel.org>
Acked-by: Lasse Collin <lasse.collin@tukaani.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
