mirror of
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/
synced 2026-11-08 18:57:22 +00:00
1,464,119 commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Stefan Agner
|
06232cb44b |
net: stmmac: resume PHY before hardware setup when opening the interface
Since the referenced commit, changing the MTU on a running interface no
longer disconnects and reconnects the PHY; __stmmac_release() merely
stops phylink, which also suspends the PHY (BMCR power-down) when WoL
is not enabled. __stmmac_open() then performs the DMA software reset in
stmmac_hw_setup() before phylink_start() resumes the PHY again.
IEEE 802.3 22.2.4.1.5 allows a PHY to stop its receive clock while
powered down, and stmmac requires a running receive clock for the DMA
software reset to complete (the phylink config sets mac_requires_rxc).
On such setups, e.g. the RK3566-based Home Assistant Green with an
RTL8211F-VD PHY in RGMII mode, any runtime MTU change now times out and
leaves the interface dead:
rk_gmac-dwmac fe010000.ethernet end0: Failed to reset the dma
rk_gmac-dwmac fe010000.ethernet end0: stmmac_hw_setup: DMA engine initialization failed
rk_gmac-dwmac fe010000.ethernet end0: __stmmac_open: Hw setup failed
rk_gmac-dwmac fe010000.ethernet end0: failed reopening the interface after MTU change
In the field this is triggered by NetworkManager applying an MTU while
activating the connection, breaking networking entirely. The same
regression has also been reported on i.MX8MP and reproduced on SoCFPGA
based systems.
Resume the PHY in __stmmac_open() before the hardware setup, making it
the counterpart of the phylink_stop() in __stmmac_release(), like
stmmac_resume() already does for the same reason. phylink_start() also
resumes the PHY, but only after stmmac_hw_setup(), and it cannot be
moved before the hardware setup since it may bring the link up
immediately from a workqueue, racing with the initialization (see the
comment in stmmac_resume()). For the regular ndo_open path the PHY has
just been attached and is not suspended, in which case
phylink_prepare_resume() does nothing.
Fixes:
|
||
Jakub Kicinski
|
e31420642d |
Included fixes:
* use rcu_dereference_bh() instead of rcu_access_pointer() where the pointer is actually dereferenced * ensure TCP global variables are initialized before they can be accessed via netlink (e.g. when attaching a TCP socket) * actually disable IPv4 redirects on multipeer interfaces (the previous attempt was a no-op and did not survive netns moves) * hash a floated peer by its transport identity only, consistently with the add and lookup paths * zero the sockaddr padding before learning a floated endpoint so it does not leak into the by_transp_addr hash key * ensure the socket is owned by ovpn before dereferencing sk_user_data * rehash a peer in the by_transp_addr table when its remote endpoint is updated via CMD_PEER_SET * avoid re-adding to the hashtables a peer that was concurrently removed (use-after-free) * limit keepalive values to one day to avoid overflowing the delayed-work delay on 32-bit systems * add the missing rtnl_link_ops->get_size callback so link messages account for the nested mode attribute -----BEGIN PGP SIGNATURE----- iJEEABYIADkWIQQr0db7q+Rc7Zog28Fc8QQzwdnOtwUCamsZiRsUgAAAAAAEAA5t YW51MiwyLjUrMS4xMiwyLDIACgkQXPEEM8HZzrdjhQD/SJjvWsxHurn7vQJ8VFw9 wb8Q06TpSjdHkd5xXpQzohoA/joMlAYnVhSlYDcDaF3DCzmCAW6fG/bpPoI4bpFj i8UD =Oppi -----END PGP SIGNATURE----- Merge tag 'ovpn-net-20260730' of https://github.com/OpenVPN/ovpn-net-next Antonio Quartulli says: ==================== Included fixes: * use rcu_dereference_bh() instead of rcu_access_pointer() where the pointer is actually dereferenced * ensure TCP global variables are initialized before they can be accessed via netlink (e.g. when attaching a TCP socket) * actually disable IPv4 redirects on multipeer interfaces (the previous attempt was a no-op and did not survive netns moves) * hash a floated peer by its transport identity only, consistently with the add and lookup paths * zero the sockaddr padding before learning a floated endpoint so it does not leak into the by_transp_addr hash key * ensure the socket is owned by ovpn before dereferencing sk_user_data * rehash a peer in the by_transp_addr table when its remote endpoint is updated via CMD_PEER_SET * avoid re-adding to the hashtables a peer that was concurrently removed (use-after-free) * limit keepalive values to one day to avoid overflowing the delayed-work delay on 32-bit systems * add the missing rtnl_link_ops->get_size callback so link messages account for the nested mode attribute * tag 'ovpn-net-20260730' of https://github.com/OpenVPN/ovpn-net-next: ovpn: fix incorrect use of rcu_access_pointer() ovpn: ensure TCP vars are initialized first ovpn: disable IPv4 redirects on MP interfaces ovpn: hash floated peer by transport identity only ovpn: zero-initialize sockaddr before learning a floated endpoint ovpn: ensure socket is owned by ovpn before deref sk_user_data ovpn: rehash peer in by_transp_addr table on CMD_PEER_SET ovpn: skip rehash for peers already removed from by_id ovpn: limit keepalive values to one day ovpn: add missing rtnl_link_ops->get_size callback ==================== Link: https://patch.msgid.link/20260730094624.4102963-1-antonio@openvpn.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
Kyle Zeng
|
0e243671bc |
ipv6: prevent in6_dev_get() from resurrecting inet6_dev
in6_dev_get() reads dev->ip6_ptr under RCU and then unconditionally increments its refcount. Device teardown can clear the pointer and drop the last reference between these operations. The increment then resurrects an object whose RCU free has already been queued, so callers can use it after it is freed. Use refcount_inc_not_zero() and return NULL when the object has already reached zero. RCU keeps the memory accessible through the attempted reference acquisition, and a successful increment pins the object for the caller. An independent run on the exact unpatched |
||
Jamal Hadi Salim
|
a347304b2c |
net/sched: cls_api: Always acquire rtnl_lock when destroying locked classifiers
Another challenge with unlocked filters.
There is a short window in tc_new_tfilter where a tcf_proto can be found
and briefly referenced by a totally unrelated, unlocked classifier's request
and cause a race.
Feng created a poc which created this race with two threads, one creating a
u32 filter and other a flower filter in the same chain/prio:
1. Both threads enter tc_new_tfilter, both find the chain empty, both
drop filter_chain_lock
2. u32 finishes tcf_proto_create("u32") first, calls
tcf_chain_tp_insert_unique() -> inserts u32_tp into the chain
3. flower finishes tcf_proto_create("flower") later, calls
tcf_chain_tp_insert_unique() -> tcf_chain_tp_find() now sees u32_tp
already there, takes a reference on it, destroys flower's own tp_new
and returns u32_tp to the caller.
Flower then hits the kind mismatch check (because it requested for kind
"flower" but tp->ops->kind is "u32") and goes through the errout path
which calls tcf_proto_put() on u32_tp. If the u32 thread has already
gone through its own errout (its change() call failed on the PoC's empty
options) and dropped its create and insert refs, flower's put is the
last one and drops u32_tp's refcnt to zero.
At this point tp->ops->destroy() runs in a context that never took
rtnl_lock. When that happens, it might cause a UAF like the following
(illustrated by the PoC):
[ +0.000710] BUG: KASAN: slab-use-after-free in u32_init (net/sched/cls_u32.c:393)
[ +0.000281] Read of size 8 at addr ffff888120022f00 by task poc_feng_xue/524
Call Trace:
u32_init (net/sched/cls_u32.c:393)
tc_new_tfilter (net/sched/cls_api.c:2378)
Allocated by task 526:
u32_init (net/sched/cls_u32.c:378)
tc_new_tfilter (net/sched/cls_api.c:2378)
Freed by task 522:
kfree
u32_destroy (net/sched/cls_u32.c:662)
tcf_proto_destroy (net/sched/cls_api.c:446)
tcf_proto_put (net/sched/cls_api.c:459)
tc_new_tfilter (net/sched/cls_api.c:2459)
Fix this by having tcf_proto_destroy() take rtnl_lock around
tp->ops->destroy() for locked classifiers whenever rtnl is not held.
To explain why I used a temp variable "not_lockless" I'd like to point to a
semi-related note on rtnl_held vs TCF_PROTO_OPS_DOIT_UNLOCKED (adding here
for future cleanup if deemed necessary):
The rtnl_held parameter and the TCF_PROTO_OPS_DOIT_UNLOCKED flag are
redundant sources of truth for whether rtnl_lock is held. Among the nine
classifier destroy(..rtnl_held..) callbacks, only flower consults the
rtnl_held parameter which it propagates to tc_setup_cb_destroy()
and tc_setup_cb_call(). The other eight (u32, flow, bpf, cgroup, route, basic,
fw, mall) ignore it entirely;-> those that call tc_setup_cb_destroy()
(u32, bpf, mall) hardcode true always instead of forwarding the parameter.
A future cleanup should remove the rtnl_held parameter from the destroy callback
signature entirely and have callers rely solely on their knowledge whether
they are running in an unlocked context.
Fixes:
|
||
Cen Zhang (Microsoft)
|
cf6f8b29be |
net/openvswitch: check Ethernet header length in key_extract()
When a packet arrives on an ARPHRD_NONE device (e.g. TUN),
ovs_flow_key_extract() trusts the user-provided skb->protocol field: if
it is ETH_P_TEB, the packet is classified as MAC_PROTO_ETHERNET and
key_extract() is called without ensuring the skb has ETH_HLEN (14) bytes
of linear data. key_extract() unconditionally pulls 2 * ETH_ALEN bytes
for MAC addresses and parse_ethertype() pulls 2 more, either of which
triggers a kernel BUG in __skb_pull() when the linear area is too small.
kernel BUG at include/linux/skbuff.h:2848!
RIP: 0010:key_extract+0xa7e/0xd90 net/openvswitch/flow.c:933
ovs_flow_key_extract+0x419/0xa70
ovs_vport_receive+0x222/0x390
netdev_frame_hook+0x3e0/0x630
tun_get_user+0x2d0c/0x38e0
Fixed by calling check_header() in key_extract() before accessing the
Ethernet header.
Fixes:
|
||
Zihan Xi
|
1a35da325c |
packet: synchronize pressure clearing with ring reconfiguration
packet_set_ring() updates the RX ring state under sk_receive_queue.lock,
but used to publish the tpacket receive mode through po->prot_hook.func
after releasing that lock. packet_poll() and packet_recvmsg() can then
run the pressure clearing path after the ring has been cleared while
still seeing tpacket_rcv, causing __packet_rcv_has_room() to dereference
stale or NULL ring storage.
Move the existing receive hook assignment into the same
sk_receive_queue.lock section as the ring state update. Keep the
assignment otherwise unchanged, including on TX ring reconfiguration, to
avoid adding behavior changes that are not required for the fix.
Serialize packet_recvmsg() pressure clearing with the same queue lock
only after PACKET_SOCK_PRESSURE has been observed. If the flag is clear
and the socket has moved away from tpacket_rcv, packet_set_ring() has
already detached the socket and waited for synchronize_net(), so no new
packet input can set the flag again.
packet_poll() already holds sk_receive_queue.lock, so it uses the new
unlocked helper directly.
Fixes:
|
||
Toke Høiland-Jørgensen
|
2a33516f9e |
net/sched: sch_cake: drop WARN_ON(1) for malformed packets in ACK filter
The sch_cake ACK filter parses packets to find the TCP header and filter
duplicated ACKs if the flow is backlogged. The parsing code contains a
WARN_ON(1) which can be triggered by a malformed IP header in certain
cases. Depending on the system configuration, this leads either to
either spamming dmesg with warnings, or a panic if panic_on_warn is set.
The code already correctly skips the offending packet in the branch that
triggers the warning, so the WARN_ON itself doesn't really serve any
purpose. So just drop it altogether to avoid the inconvenient side
effects.
Fixes:
|
||
Xuanqiang Luo
|
d0f86fb36e |
udp: fix potential use-after-free in tunnel segmentation
__skb_udp_tunnel_segment() gets the UDP header before ensuring the
tunnel header is in the skb head. If the pull reallocates skb->head,
the saved UDP header pointer is no longer valid.
Get the UDP header after the pull to avoid a potential use-after-free.
Fixes:
|
||
Hidayath Khan
|
d141f087b1 |
s390/qeth: validate user buffer length in SNMP and ARP query ioctls
qeth_snmp_command() and qeth_l3_arp_query() allocate a buffer sized by
a user-supplied length (udata_len) without checking a lower bound, then
set udata_offset to a fixed non-zero value and pass both to a reply
callback. The callback bounds-checks the copy with
if ((udata_len - udata_offset) < len)
Both fields are u32, so a udata_len smaller than udata_offset makes the
subtraction wrap and the check pass, and the following memcpy() writes
past the allocation. A udata_len of 0 also yields ZERO_SIZE_PTR from
kzalloc(), which the existing NULL check does not catch.
Reject buffers smaller than udata_offset before allocating, so the
callback subtraction can no longer underflow.
Fixes:
|
||
|
Zihan Xi
|
4ff9548d84 |
ipv4: Fix fib_nlmsg_size() for RTA_VIA nexthops
fib_nlmsg_size() still estimates nexthop space as if every gateway is
encoded as an IPv4 RTA_GATEWAY attribute. IPv4 routes can also carry an
IPv6 gateway, which fib_nexthop_info() dumps as RTA_VIA.
As a result, route notifications can allocate an skb that is too small.
fib_dump_info() then fails with -EMSGSIZE and rtmsg_fib() hits the
WARN_ON() that marks such failures as a fib_nlmsg_size() bug. With
panic_on_warn set, this becomes a kernel panic.
Mirror the actual nexthop dump layout in fib_nlmsg_size(): account for
IPv6 nexthop gateways dumped as RTA_VIA, for the no-header rtnexthop
layout used inside RTA_MULTIPATH, and for RTA_FLOW only when it is
actually present.
Fixes:
|
||
Daming Li
|
5d9686af29 |
net: smc: fix splice entry lifetime imbalance in smc_rx_splice
smc_rx_splice() passes pages to splice_to_pipe() before taking the
references that cover the lifetime of each splice entry. In the
VM-backed RMB path, splice_to_pipe() may drop unqueued entries through
smc_rx_spd_release(), while queued entries are released later via the
pipe buffer callback.
The old post-splice accounting also derives the number of queued VM pages
from an offset mutated while building the descriptor, and a multi-page
splice pairs one sock_hold() with multiple sock_put() calls.
Take the page and socket references for every candidate entry before
splice_to_pipe(), and drop the matching private state, page reference,
and socket reference from smc_rx_spd_release() for entries that never
get queued. This fixes a refcount imbalance that can underflow page
refcounts and trigger a use-after-free.
Fixes:
|
||
Alok Tiwari
|
1cb4298810 |
bnge: Fix NULL pointer dereference in aux device release
If allocation of auxr_dev fails during auxiliary device setup, the error
path calls auxiliary_device_uninit(), which eventually invokes
bnge_aux_dev_release().
The release callback unconditionally dereferences aux_priv->auxr_dev->pdev
to retrieve the parent bnge_dev. Since auxr_dev has not yet been allocated
on this failure path, the dereference results in a NULL pointer exception
Retrieve the parent bnge_dev from the auxiliary device's parent instead of
auxr_dev, and free auxr_dev only when it was successfully allocated. This
allows the release callback to correctly clean up partially initialized
auxiliary devices.
Fixes:
|
||
Yi Cong
|
1f428e3094 |
net: usb: ax88179_178a: fix skb leak in ax88179_tx_fixup()
When the interface has NETIF_F_SG enabled and skb_linearize() fails in
ax88179_tx_fixup(), the function returns NULL without freeing the skb.
usbnet_start_xmit() treats a NULL return from tx_fixup() as a drop
(info->flags does not set FLAG_MULTI_PACKET for this driver), jumping
to the "drop" label where it does `if (skb) dev_kfree_skb_any(skb)`.
Because tx_fixup() returned NULL, the local skb variable in
usbnet_start_xmit() is NULL, so the original skb is never freed — a
memory leak on every TX frame whose linearization fails (i.e. under
memory pressure).
Free the skb before returning, matching the error handling already used
for the pskb_expand_head() failure path in the same function.
Fixes:
|
||
|
Jakub Kicinski
|
5243c3e3ad |
Merge branch 'xsk-harden-tx-metadata-validation-against-races'
Stanislav Fomichev says: ==================== xsk: harden TX metadata validation against races Cen Zhang reported a KASAN out-of-bounds read when AF_XDP is configured with a TX metadata area smaller than struct xsk_tx_metadata. The metadata is also shared with user space, so reading its flags more than once can produce inconsistent validation and processing decisions. Require enough space for the flags and one request field, validate the launch-time field against the configured metadata length, and use one snapshot of the flags while processing each request. Carry the validated decision through completion handling so later user-space changes cannot enable an unrequested completion timestamp. Reported-by: AutonomousCodeSecurity@microsoft.com Reported-by: Cen Zhang (Microsoft) <blbllhy@gmail.com> Link: https://lore.kernel.org/netdev/20260720155210.34229-1-blbllhy@gmail.com/ ==================== Link: https://patch.msgid.link/20260727161959.885642-1-sdf@fomichev.me Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
Stanislav Fomichev
|
849b1664db |
xsk: validate metadata when processing requests
The zero-copy path validates TX metadata while obtaining the descriptor
context, then reads it again later when preparing the hardware request.
User space can change the metadata between those operations and bypass the
original validation.
Validate the metadata in xsk_tx_metadata_request() and use the resulting
flags snapshot for every feature check. Read request fields once so all
zero-copy drivers process only values observed after successful
validation.
Fixes:
|
||
|
Stanislav Fomichev
|
ddd0d6c5bf |
xsk: move xsk_tx_metadata_request() to xdp_sock_drv.h
xsk_tx_metadata_request() must validate metadata with
xsk_buff_valid_tx_metadata(), which is defined in xdp_sock_drv.h. Move the
helper there before adding that dependency. All callers already include
the destination header, so this has no functional effect.
Fixes:
|
||
|
Stanislav Fomichev
|
439ce2dddf |
xsk: validate launch-time metadata size
Launch-time metadata extends beyond the first 16 bytes of struct
xsk_tx_metadata. Reject the request when the registered metadata area does
not contain the complete field.
Snapshot the validated flags for the generic transmit path and use that
snapshot for request and completion processing, avoiding inconsistent
decisions if user space changes the flags concurrently.
Note that only xsk_skb_metadata is properly using the flags,
__xsk_buff_get_metadata ignores them. Next commits address that.
Fixes:
|
||
|
Stanislav Fomichev
|
9f60a67df8 |
xsk: clear metadata pointer when no timestamp is requested
User space can change metadata flags after request processing. Rereading
them during completion can therefore make the kernel write a timestamp
that was not requested when the packet was submitted.
Clear the metadata pointer during request processing unless timestamp
completion is requested. Completion handling can then use the pointer
itself instead of rereading the flags.
On the mlx5 multi-packet WQE path metadata is evaluated per batch:
xsk_tx_metadata_request() runs only for the descriptor that starts a
session, just like the checksum offload that is applied once through the
shared WQE. Only that descriptor's pointer is reset, so completion
handling can record a timestamp for the other descriptors of the session
regardless of their own XDP_TXMD_FLAGS_TIMESTAMP bit. The write stays
inside the metadata area; the single-WQE, other zero-copy, and generic
paths reset the pointer per descriptor and are unaffected.
Fixes:
|
||
|
Stanislav Fomichev
|
19366db6df |
xsk: pass TX metadata pointer by reference
Completion handling needs to know whether a timestamp was requested when
the metadata was processed. Let xsk_tx_metadata_request() update the
caller's metadata pointer so that decision can be carried forward without
rereading user-controlled flags.
This only changes the interface; behavior remains unchanged.
Fixes:
|
||
|
Stanislav Fomichev
|
1bb30b181d |
xsk: require at least 16 bytes of TX metadata
AF_XDP accepts a TX metadata length as small as eight bytes, but every
supported request needs the flags plus at least one eight-byte request
field. Such short metadata also lets the kernel read beyond the registered
area.
Require 16 bytes rather than sizeof(struct xsk_tx_metadata) to preserve
compatibility with applications that do not use launch-time metadata.
Fixes:
|
||
|
Jakub Kicinski
|
d5c5ecea1f |
Merge branch 'vsock-virtio-fix-worker-access-after-virtqueue-teardown'
Weiming Shi says: ==================== vsock/virtio: fix worker access after virtqueue teardown Virtio-vsock workers can remain queued while freeze deletes the virtqueues. This series prevents workers delayed across freeze and restore from retaining pointers to deleted queues, and prevents the RX worker from refilling its queue after teardown. ==================== Link: https://patch.msgid.link/cover.1785352330.git.bestswngs@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
Weiming Shi
|
a31e0ad444 |
vsock/virtio: avoid refilling the RX queue after teardown
Commit |
||
|
Weiming Shi
|
ebac8f6b1e |
vsock/virtio: read virtqueues under worker locks
Commit |
||
Will Chen
|
d1000fd799 |
bnxt: fix memory leak in bnxt_queue_mem_alloc error cases
There is a small memory leak in bnxt_queue_mem_alloc:
when bnxt_alloc_rx_agg_bmap() succeeds
but bnxt_alloc_one_tpa_info() later fails,
the rx_agg_bmap allocated by bnxt_alloc_rx_agg_bmap()
is not freed in the fallthrough cleanup cases.
Free the rx_agg_bmap in the err_free_rx_agg_ring case
and initialize clone->rx_agg_bmap = NULL earlier in the function
to allow for safe fallthrough.
Fixes:
|
||
Yuejie Shi
|
d1ad8fb2ac |
ipv6: fix Route Information option length validation
rt6_route_rcv() validates the Route Information option (RFC 4191) length
against the prefix length, but both checks are off by one.
rinfo->length is the ND option length in units of 8 octets and it
*includes* the 8-byte option header, so an option carrying N bytes of
prefix has length == 1 + N/8. RFC 4191 section 2.3 requires length 3
when Prefix Length is greater than 64, and 2 or 3 when it is greater
than 0. The code accepts length >= 2 and length >= 1 respectively.
ipv6_addr_prefix() then copies prefix_len/8 bytes out of rinfo->prefix,
so a Router Advertisement with (prefix_len=128, length=2) or
(prefix_len=64, length=1) makes the kernel read up to 8 bytes past the
end of the option. Those bytes end up in the prefix of the route that
gets installed, so they are visible to userspace:
# RA with a Route Information option (prefix_len=128, length=2)
# followed by a source link-layer address option, 01 01 de ad be ef ca fe
$ ip -6 route show
2001:db8:dead:beef:101:dead:beef:cafe via fe80::1234 dev veth0 proto ra
^^^^^^^^^^^^^^^^^^ the next option, read out of bounds
When the Route Information option is the last one in the packet, those
eight bytes come from the skb tail room instead.
Reject the option lengths RFC 4191 does not allow.
Fixes:
|
||
Baul Lee
|
9f2cf069a9 |
sctp: keep chunk->transport in step with the list it is queued on
__sctp_outq_flush_rtx() moves a gap-acked chunk onto another transport's
transmitted list without updating chunk->transport:
if (chunk->tsn_gap_acked) {
list_move_tail(&chunk->transmitted_list,
&transport->transmitted);
continue;
}
The chunk then sits on a live transport's list while chunk->transport still
names a different one. If that transport is removed - sctp_assoc_rm_peer()
from an ASCONF Delete-IP - sctp_transport_free() RCU-frees it and the chunk
is left with a dangling pointer. sctp_assoc_rm_peer() scrubs
peer->transmitted and asoc->outqueue.out_chunk_list, but the chunk is on
neither.
The pointer is not followed while tsn_gap_acked is set. A SACK that
reneges on the TSN clears the flag, and the next SACK reaches
tchunk->transport->flight_size -= sctp_data_size(tchunk);
inside the freed transport. KASAN reports a slab-use-after-free read in
sctp_check_transmitted(), freed from sctp_assoc_rm_peer(). Both the
removal and the SACKs come from the association peer.
Set chunk->transport at the move. The ordinary resend path needs nothing:
it reaches its list_move_tail() only after sctp_packet_append_chunk()
returned SCTP_XMIT_OK, and __sctp_packet_append_chunk() has rebound the
chunk by then.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com>
Fixes:
|
||
Nathan Gao
|
0e125ecfe2 |
tcp: do not change rcv_ssthresh in tcp_measure_rcv_mss()
Commit |
||
Michael Guralnik
|
af39eb111c |
net/mlx5: fw_tracer, return NULL on create error
Tracer creation can fail by returning either NULL or ERR_PTR.
The return value is stored without a check on the device, and users
treat ERR_PTR and NULL the same way.
This also causes a crash in the core dump logic, which is missing the
ERR_PTR check and ends up dereferencing it, as shown in the trace below.
Switch tracer creation to return NULL on failure only, so callers only
need a single NULL check.
Internal error: Oops: 0000000096000006 [#1] SMP
Modules linked in: mlx5_ib ib_uverbs ib_core ipv6 mlx5_core
CPU: 1 UID: 0 PID: 12 Comm: kworker/u16:0 Not tainted 6.19.7 #1 PREEMPT(none)
Workqueue: mlx5_health0001:01:00.0 mlx5_fw_reporter_err_work [mlx5_core]
pstate: a3400009 (NzCv daif +PAN -UAO +TCO +DIT -SSBS BTYPE=--)
pc : mlx5_fw_tracer_trigger_core_dump_general+0x58/0xe0 [mlx5_core]
lr : mlx5_fw_tracer_trigger_core_dump_general+0x40/0xe0 [mlx5_core]
sp : ffff800081cf3c40
x29: ffff800081cf3c90 x28: 0000000000000000 x27: 0000000000000000
x26: ffff000080018828 x25: 0000000000000000 x24: ffff000080304a05
x23: ffff800081cf3d80 x22: ffff0000847e01a0 x21: 0000000000000000
x20: ffff0000847e01a0 x19: ffffffffffffffa1 x18: ffff80008310bbf0
x17: ffff800080119650 x16: ffff80008010df54 x15: ffff80008010d4ac
x14: ffff800079c202e4 x13: ffff80008002fe60 x12: ffff800080119650
x11: ffff80008010df54 x10: ffff80008010d4ac x9 : ffff800079c203d8
x8 : ffff800081cf3c88 x7 : 0000000000000000 x6 : 0000000000000000
x5 : 0000000000000000 x4 : 0000000000000008 x3 : 0000000000000030
x2 : 0000000000000008 x1 : 0000000000000000 x0 : 00000000c5c4000e
Call trace:
mlx5_fw_tracer_trigger_core_dump_general+0x58/0xe0 [mlx5_core] (P)
mlx5_fw_reporter_dump+0x30/0x2e0 [mlx5_core]
devlink_health_do_dump+0x9c/0x160
devlink_health_report+0x1c0/0x288
mlx5_fw_reporter_err_work+0xac/0xc0 [mlx5_core]
process_one_work+0x15c/0x3d8
worker_thread+0x18c/0x320
kthread+0x148/0x228
ret_from_fork+0x10/0x20
Code: b9400000 5ac00800 7a401800 540003ca (3940a260)
---[ end trace 0000000000000000 ]---
Kernel panic - not syncing: Oops: Fatal exception
SMP: stopping secondary CPUs
Kernel Offset: disabled
CPU features: 0x000000,00078031,75fce5a1,35fffe67
Memory Limit: none
---[ end Kernel panic - not syncing: Oops: Fatal exception ]---
Fixes:
|
||
Chris Mi
|
43e970d961 |
net/mlx5: SF, Handle function changed event
When host is powered off, firmware does not send vhca_state event
for every probed host SF on the DPU because it may have deployed
thousands of SFs to the host. Instead it sends a function changed
event. Currently, only VFs handle this event. This commit extends
support to SFs.
When DPU user deactivates[1] SFs, mlx5 expects vhca_state event
and leaves the SF in dangling state[2].
When DPU user deletes[3] SFs, mlx5 also expects vhca_state event
and destroys the SF resources[4].
Fix it by changing SF to the right state and freeing SF resources
when the function changed event is received.
When this event is received, driver checks all SF states.
- If state is in_use, change it to active.
- If state is teardown_request, change it to allocated.
And SF hardware table entry is freed if it is pending for delete.
[1]
# devlink port function set en3f0c1pf0sf0 state inactive
[2]
# devlink port function set en3f0c1pf0sf0 state active
Error: mlx5_core: SF is inactivated but it is still attached.
kernel answers: Device or resource busy
[3]
# devlink port show
pci/0000:03:00.0/229376: type eth netdev en3f0c1pf0sf0 \
flavour pcisf controller 1 pfnum 0 sfnum 0 splittable false
function:
hw_addr 00:00:00:00:00:00 state active opstate attached \
roce enable trust off max_uc_macs 4096 max_io_eqs 8
# devlink port del en3f0c1pf0sf0
[4]
# devlink port add pci/0000:03:00.0 flavour pcisf pfnum 0 sfnum 0 \
controller 1
Error: mlx5_core: SF already exist. Choose different sfnum.
kernel answers: File exists
Fixes:
|
||
Or Har-Toov
|
1c4dac9bf1 |
devlink: fix net namespace reference leak in reload
devlink_nl_reload_doit() calls devlink_netns_get(), which returns a net
with a held reference. When the requested namespace differs from the
current one and the reload action is not DRIVER_REINIT, the function
returns -EOPNOTSUPP without releasing the reference. Add the missing
put_net() on this error path.
Fixes:
|
||
Jiawen Liu
|
f307a7dc32 |
net: hisilicon: hix5hd2_gmac: remove redundant NAPI delete
hix5hd2_dev_remove() calls netif_napi_del() before unregister_netdev().
This is not needed because free_netdev() deletes all NAPI instances
attached to the net_device.
Remove the redundant call and let the networking core tear down the NAPI
instance during unregister_netdev(). The probe error path still keeps its
explicit netif_napi_del(), because the device has not been registered
there.
Fixes:
|
||
|
Jamal Hadi Salim
|
47d7f70512 |
net/sched: cls_route: fix fastmap use-after-free on filter
The route4 classifier maintains a 16-slot fastmap cache that stores raw
struct route4_filter pointers indexed by (id, iif). The reader
(route4_classify) populates this cache via route4_set_fastmap() for every
classified packet that hits a filter. The writer (route4_delete,
route4_change) clears the cache via route4_reset_fastmap() before
RCU-deferred kfree of the filter.
This creates a UAF race:
1. Reader walks the RCU-protected bucket chain, finds filter f
2. Writer unlinks f, calls route4_reset_fastmap(), then tcf_queue_work()
3. Reader calls route4_set_fastmap() and writes f into the cache
*after* the writer's reset, caching a pointer about to be freed
4. After the RCU grace period, kfree(f) executes
5. Next classified packet on the same (id, iif) tuple hits the stale
fastmap entry and reads f->res from freed memory
Reproduced with an mdelay(100) accelerator in route4_set_fastmap() and a
concurrent add/delete stress test (provided by both zdi and Santosh).
Both triggered KASAN slab-use-after-free reports in the route4 fastmap
paths.
Fix:
Introduce a per-filter boolean dying flag to suppress stale fastmap
republishing by in-flight readers.
Fixes:
|
||
Zhiling Zou
|
653d7ddf6c |
inet: frags: publish queues before arming timer
inet_frag_create() arms the fragment queue timer before inserting the
queue into the fqdir rhashtable. If the namespace fragment timeout is
zero or negative, the timer can run before the queue is published.
The timer callback then marks the queue complete, tries to remove a node
that is not in the hash table yet, and drops the anticipated hash
reference. Creation can subsequently publish the completed queue without
restoring that reference, leaving a stale hash node after the caller drops
the remaining reference.
Publish the queue first and arm the timer while holding the queue lock.
This makes timer expiry wait until the queue is visible in the hash table,
so inet_frag_kill() can remove the node and balance the hash reference.
Fixes:
|
||
|
Baul Lee
|
63488dba65 |
net: bridge: mrp: fix uninitialised bytes on the wire
br_mrp_alloc_test_skb() builds MRP test frames on an skb from
dev_alloc_skb(), which does not clear the linear data area. On the MRA
ring-role branch the sub-option TLV header is appended with
sub_tlv = skb_put(skb, sizeof(*sub_tlv));
sub_tlv->type = BR_MRP_SUB_TLV_HEADER_TEST_AUTO_MGR;
so sub_tlv->length is never written, and the two trailing alignment bytes
are appended with a bare skb_put() that does not clear them either. The
neighbouring oui and sub_opt regions are explicitly zeroed, so three
uninitialised bytes are left in every MRA MRP_Test frame that goes out.
Put the sub-option TLV header and the alignment padding in a single
skb_put_zero(), which clears both. The AUTO_MGR sub-TLV carries no
payload, so the zeroed length field is already the value it should have.
Fixes:
|
||
Mahanta Jambigi
|
9762450949 |
net/smc: fix qentry overwrite for CONFIRM_LINK and ADD_LINK_CONT in smc_llc_event_handler()
The SMC_LLC_CONFIRM_LINK / SMC_LLC_ADD_LINK_CONT branch in
smc_llc_event_handler() stores an incoming qentry into the local LLC flow
without first checking whether a qentry is already pending. If a malicious or
buggy peer sends a second CONFIRM_LINK or ADD_LINK_CONT request while a flow is
active and flow->qentry is already set, smc_llc_flow_qentry_set() overwrites the
pointer without freeing the previous allocation, leaking one kmalloc-96 object
per spurious message.
The sibling SMC_LLC_DELETE_LINK branch already has the correct !flow->qentry
guard. Apply the same guard to the CONFIRM_LINK/ADD_LINK_CONT branch so that a
duplicate message when qentry is already occupied falls through to break and is
freed by the kfree(qentry) at the out: label, rather than silently leaking the
existing allocation.
The response direction (smc_llc_rx_response()) is unaffected: it already guards
with flow->qentry at the equivalent site and drops duplicate responses
correctly.
Fixes:
|
||
|
Baul Lee
|
2195424c3d |
net/x25: fix use-after-free of the socket by its timers
The x25 timers are armed with mod_timer() and cancelled with
timer_delete(), so a pending timer holds no reference on the socket and a
cancel does not wait for a callback already running on another CPU.
x25_heartbeat_expiry() also rearms unconditionally, so it can reinstall
sk->sk_timer after __x25_destroy_socket() has passed its cancel point.
The following __sock_put() frees the socket while the timer is still
queued, and the next expiry uses freed memory. KASAN reports a
slab-use-after-free on the kmalloc-2k object freed by close().
timer_delete_sync() cannot be used here: x25_heartbeat_expiry() and
x25_timer_expiry() both reach the cancels from inside the timer they
would wait on, through __x25_destroy_socket() and x25_disconnect().
Arm the timers with sk_reset_timer() and cancel them with sk_stop_timer()
so that an armed timer owns a reference, and release it in both expiry
handlers. Rearm the heartbeat only while sk_hashed(sk) is still true,
since __x25_destroy_socket() unlinks the socket before dropping it. Arm
the deferred destroy timer the same way and drop its reference in
x25_destroy_timer().
Reproduced on net with KASAN, with the heartbeat period shortened so the
window recurs. With this patch the reproducer no longer triggers a
report and /proc/net/x25 drains.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com>
Fixes:
|
||
Nikhil P. Rao
|
57d635329d |
pds_core: cancel pending PCI reset work on AER recovery
pdsc_check_pci_health() queues pci_reset_work when it sees a broken PCI
connection, and nothing cancels it. When the PCI core starts AER
recovery, pdsc_pci_error_detected() runs pdsc_reset_prepare() and
recovers the device, but a pci_reset_work queued just before is left
pending. If it runs after recovery released the device lock, it resets a
device the driver now considers healthy, bouncing the link for no reason.
Cancel pci_reset_work in pdsc_pci_error_detected() after
pdsc_reset_prepare(), which has already stopped the health thread so it
cannot requeue the work. cancel_work_sync() is safe under the device
lock here because pdsc_pci_reset_thread() uses pci_try_reset_function(),
which returns instead of blocking on the lock. Only PFs initialize
pci_reset_work, so guard the cancel with !is_virtfn.
Fixes:
|
||
|
Nikhil P. Rao
|
cd09971dcc |
pds_core: keep the health thread stopped during reset
Commit |
||
Shay Drory
|
6ddfba2ea9 |
net/mlx5e: TC, Check if flow is PEER before acquiring devcom lock
In case __mlx5e_add_fdb_flow() fails in lower levels, the flow is
deleted via mlx5e_tc_del_flow(), and mlx5e_tc_del_flow() is acquiring
ESW devcom lock without condition. In addition, in case of peer_flow,
__mlx5e_add_fdb_flow() is called while holding ESW devcom comp lock.
This results in an AA deadlock.
To fix this, introduce a new PEER flag that is set on flows created as
peer flows (the duplicate flows on peer devices), and check it in
mlx5e_tc_del_flow() before acquiring ESW devcom lock.
Lockdep splat:
============================================
WARNING: possible recursive locking detected
============================================
Possible unsafe locking scenario:
CPU0
----
lock(&comp->lock_key#2);
lock(&comp->lock_key#2);
*** DEADLOCK ***
Call Trace:
<TASK>
dump_stack_lvl+0x69/0xa0
print_deadlock_bug.cold+0xbd/0xca
__lock_acquire+0x1671/0x2ec0
lock_acquire+0x10e/0x2e0
down_read+0x95/0x430
mlx5_devcom_for_each_peer_begin+0x4e/0xe0 [mlx5_core]
mlx5e_tc_del_flow+0x11d/0xa70 [mlx5_core]
mlx5e_flow_put+0x99/0x100 [mlx5_core]
__mlx5e_add_fdb_flow+0x409/0xf00 [mlx5_core]
mlx5e_configure_flower+0x2a86/0x4100 [mlx5_core]
mlx5e_rep_setup_tc_cls_flower+0x12f/0x1b0 [mlx5_core]
mlx5e_rep_setup_tc_cb+0x153/0x750 [mlx5_core]
tc_setup_cb_add+0x1dc/0x470
fl_change+0x2f4d/0x626d [cls_flower]
tc_new_tfilter+0x79b/0x2310
rtnetlink_rcv_msg+0x778/0xad0
do_syscall_64+0x70/0x960
entry_SYSCALL_64_after_hwframe+0x4b/0x53
</TASK>
Fixes:
|
||
Satish Kharat
|
ec680ea4ba |
enic: fix tx_hang_reset use-after-free on device removal
enic_remove() cancels the reset and change_mtu_work items but does not
cancel tx_hang_reset. A TX timeout that fires while the device is being
removed can schedule enic_tx_hang_reset() so that it runs after
free_netdev(), resulting in a use-after-free.
cancel_work_sync() alone is not sufficient here: the still-live watchdog
and notify paths can re-schedule these work items in the window between
the cancel and unregister_netdev(). Use disable_work_sync(), which
cancels the work and blocks any subsequent schedule_work() from
requeuing it, and apply it to the reset and change_mtu_work items as
well so the same requeue race is closed for all teardown work.
Fixes:
|
||
Doruk Tan Ozturk
|
c2707480cf |
net/packet: reset the MAC header on the packet-socket transmit path
packet_parse_headers() resets the MAC header only for a SOCK_RAW frame whose socket did not bind a protocol. A protocol-bound SOCK_RAW socket, any SOCK_DGRAM frame, and the legacy SOCK_PACKET path therefore leave skb->mac_header unset here. For frames sent via __dev_queue_xmit() this is harmless: it resets the MAC header unconditionally. But the packet-socket PACKET_QDISC_BYPASS path uses dev_direct_xmit(), which does not, so the frame reaches ndo_start_xmit() with the MAC header unset. A driver that reads eth_hdr(skb) on transmit then dereferences skb->head + (u16)~0, an out-of-bounds access ~64 KiB past the head -- the same class fixed for one consumer in commit |
||
Pavel Begunkov
|
53a43508ee |
net: devmem: prevent net-iov / page mixing
We should either have net_iov or page backed frags in a single skb,
otherwise it blows up down the stack. Don't allow mixing in
zerocopy_fill_skb_from_devmem().
Fixes:
|
||
Xiang Mei (Microsoft)
|
683c6ba6e5 |
bonding: alb: re-check primary_is_promisc under RTNL in bond_alb_monitor
bond_alb_monitor() reads primary_is_promisc under RCU, then drops RCU and
takes RTNL via rtnl_trylock() before undoing the promiscuity it set on the
active slave. In that window the active slave can change under RTNL
(RTM_DELLINK -> __bond_release_one() -> bond_alb_handle_active_change()),
which already drops the promiscuity and clears primary_is_promisc. The
monitor still acts on the stale decision: if the slave was removed with no
failover, curr_active_slave is now NULL and the deref faults; if it failed
over, the stale dev_set_promiscuity(-1) underflows the new slave's
promiscuity counter and pins it in IFF_PROMISC.
Oops: general protection fault, probably for non-canonical address ...
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
Workqueue: b42 bond_alb_monitor
RIP: 0010:bond_alb_monitor (drivers/net/bonding/bond_alb.c:1600)
process_one_work (kernel/workqueue.c:3322)
worker_thread (kernel/workqueue.c:3486)
kthread (kernel/kthread.c:436)
ret_from_fork (arch/x86/kernel/process.c:158)
Kernel panic - not syncing: Fatal exception
Re-check primary_is_promisc (and curr_active_slave) after taking RTNL so
the monitor only undoes an increment it still owns. The other bonding
monitors already re-read state under RTNL in their commit phase
(bond_miimon_commit/bond_ab_arp_commit); bond_alb_monitor() was the only
one acting on the pre-trylock decision.
Fixes:
|
||
Fan Ye
|
1881f2efbf |
Revert "net: thunderbolt: Enable end-to-end flow control also in transmit"
This reverts commit |
||
Jijie Shao
|
3860d8748a |
net: hns3: fix speed configuration residue after driver reload
After setting a 100G optical port to 40G via ethtool and reloading
the driver, the port remains at 40G instead of reverting to the
firmware default speed of 100G.
The commit referenced in Fixes: added two overwrites in
hclge_init_ae_dev() for non-copper media, so that optical ports
connected to forced-mode remotes inherit the firmware-preset
autoneg and speed instead of the hardcoded defaults:
req_autoneg = mac.autoneg
req_speed = mac.speed (when autoneg disabled)
The autoneg overwrite keeps existing behavior:
hclge_set_autoneg_speed_dup() already uses mac.autoneg (not
req_autoneg) since it was introduced, so autoneg inheritance from
firmware was already in place. This part is kept.
The speed overwrite, however, introduces the residue: mac.speed
reflects whatever was last programmed into the MAC, and after unload
firmware does not restore the MAC speed to the flash default. So if
the user changed speed via ethtool in a prior load, mac.speed still
carries that value on reload and req_speed inherits it.
Fix by dropping the req_speed overwrite only. req_speed keeps the
firmware default value set in hclge_configure() (cfg.default_speed),
so a reload reverts the speed to default, matching the expectation
that a driver reload resets link configuration.
Trade-off: on optical ports whose firmware default speed does not
match a forced-mode remote, reload now drops the link and the user
must re-apply ethtool configuration. This is acceptable: a driver
reload is expected to reset link configuration, not to inherit
runtime state from before unload. The autoneg inheritance is left
in place as established behavior; changing it is out of scope for
this patch and would itself be a user-perceivable behavior change.
Fixes:
|
||
Linus Torvalds
|
2812e64e15 |
This is again larger than usual: the backlog accumulated in the past weeks
is not done yet. I'm not aware of any known pending regression.
Including fixes from netfilter, Bluetooth, WiFi and CAN.
Current release - regressions:
- eth: tun/vhost: revert avoid ptr_ring tail-drop when a qdisc is present
- bluetooth: remove unnecessary hci_conn_get in create_conn_sync
- can: isotp: fix timer drain order, wakeup handling and tx_gen ordering
Previous releases - regressions:
- core: do not send ICMP/NDISC Redirects when peer allocation fails
- ipv6: take nexthop lock for f6i_list walks in replace check and notify
- wifi: fix an ath12k MLO regression impacting WCN7850/QCC2072.
- netfilter: nf_tables: make nft_object rhltable per table
- af_unix: fix listen() succeeding on sockets in the wrong state
- openvswitch: fix potential UAF on meter attach failure
- bluetooth:
- fix advertising data UAFs
- avoid deadlocks in iso_sock_timeout
- smc: fix socket use-after-free during link group termination
- dpll: use pin owner's dpll ref for pin-level attribute reporting
- eth: veth: convert frag_list skbs before running XDP
- eth: ice: wait for reset completion in ice_resume()
- eth: igc: remove napi_synchronize() in igc_down()
- eth: vxlan: use pskb_network_may_pull() for transmit path header pulls
Previous releases - always broken:
- xsk: fix AF_XDP multi-buffer Tx descriptor reclaim
- psp: fix NULL genl_sock deref race with concurrent netns teardown
- netfilter: widen NAT rewrite delta to s32 in sip_help_tcp()
- can: peak_usb: fix double free of transfer buffer on URB submit error
- dibs: fix use-after-free of dmb_node in loopback attach/detach/unregister
- sctp: prevent peer transport count overflow
- eth: idpf: bound interrupt-vector register fill to the allocated array
- dsa: mt7530: error out on failed reads in MT7531 PHY polling
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=jLD8
-----END PGP SIGNATURE-----
Merge tag 'net-7.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"This is again larger than usual: the backlog accumulated in the past weeks
is not done yet. I'm not aware of any known pending regression.
Including fixes from netfilter, Bluetooth, WiFi and CAN.
Current release - regressions:
- bluetooth: remove unnecessary hci_conn_get in create_conn_sync
- can: isotp: fix timer drain order, wakeup handling and tx_gen
ordering
- eth:
- tun/vhost: revert avoid ptr_ring tail-drop when a qdisc is
present
Previous releases - regressions:
- core: do not send ICMP/NDISC Redirects when peer allocation fails
- ipv6: take nexthop lock for f6i_list walks in replace check and
notify
- wifi: fix an ath12k MLO regression impacting WCN7850/QCC2072.
- netfilter: nf_tables: make nft_object rhltable per table
- af_unix: fix listen() succeeding on sockets in the wrong state
- openvswitch: fix potential UAF on meter attach failure
- bluetooth:
- fix advertising data UAFs
- avoid deadlocks in iso_sock_timeout
- smc: fix socket use-after-free during link group termination
- dpll: use pin owner's dpll ref for pin-level attribute reporting
- eth:
- veth: convert frag_list skbs before running XDP
- ice: wait for reset completion in ice_resume()
- igc: remove napi_synchronize() in igc_down()
- vxlan: use pskb_network_may_pull() for transmit path header pulls
Previous releases - always broken:
- xsk: fix AF_XDP multi-buffer Tx descriptor reclaim
- psp: fix NULL genl_sock deref race with concurrent netns teardown
- netfilter: widen NAT rewrite delta to s32 in sip_help_tcp()
- can: peak_usb: fix double free of transfer buffer on URB submit error
- dibs: fix use-after-free of dmb_node in loopback attach/detach/unregister
- sctp: prevent peer transport count overflow
- dsa: mt7530: error out on failed reads in MT7531 PHY polling
- eth:
- idpf: bound interrupt-vector register fill to the allocated array"
* tag 'net-7.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (156 commits)
qede: sync udp_tunnel ports outside qede_lock in the recovery path
net: openvswitch: fix potential UAF on meter attach failure
octeontx2-pf: Set correct sequence for carrier off and tx queue stop
net: libwx: fix FDIR ATR queue mismatch for software VLAN packets
net: dsa: realtek: use devm_mutex_init for l2_lock
net: dsa: realtek: use devm_mutex_init for vlan_lock
net: dsa: realtek: use devm_mutex_init for regmap lock
net: dsa: realtek: rtl8365mb: use devm_mutex_init for mib_lock
ptp: netc: fix potential interrupt storm caused by incorrect unbind order
net: mana: Return error code from mana_create_rxq()
net: openvswitch: fix skb leak on flow key update failure during ct
net: openvswitch: fix skb leak on flow key update failure during recirculation
net: stmmac: Fix E2E delay mechanism
net: dsa: mt7530: error out on failed reads in MT7531 PHY polling
net: dsa: mt7530: error out on failed reads in ATC/VTCR command polling
net: dsa: mt7530: check bus->read() errors in the MDIO regmap backend
Revert "tun/tap: add ptr_ring consume helper with netdev queue wakeup"
Revert "vhost-net: wake queue of tun/tap after ptr_ring consume"
Revert "ptr_ring: move free-space check into separate helper"
Revert "tun/tap & vhost-net: avoid ptr_ring tail-drop when a qdisc is present"
...
|
||
|
Linus Torvalds
|
110b5cdd5b |
gpio fixes for v7.2-rc6
- fix a memory leak in gpio-sloppy-logic-analyzer - fix a regression in GPIO hog handling for hogs without direction specified - extend the critical section in IRQ handling in gpio-pca953x to cover the reads from the direction register - disable the interrupt on errors when restoring context in gpio-pca953x - apply the initial value when setting direction in gpio-by-pinctrl - use raw spinlock for the register lock in gpio-pch to address locking context issues -----BEGIN PGP SIGNATURE----- iQIzBAABCgAdFiEEkeUTLeW1Rh17omX8BZ0uy/82hMMFAmprAeQACgkQBZ0uy/82 hMOiDw//Q1GjD4H+d9s8xgUPOKJGX7hoTJiV33KubDN3cWwVlQ474Co4KEgLU4WA FIdyBak2htwuPt6gg+bKAsZO/PeKi2tP/yIhfeMpdL7GI2Q5V4wANzWtGxixI1Zd DDy6sJV4MDD7tCshMRCBUc8oevrbgN6Isd7jw5WE48GzTcEKUWN/PY8TIVYMXbVO 2rsn2ah2nz3v+qmIHKmV1aVeOJV3+x0wdEd5ZpkfYeoO8Kp9N11VPBtji6cJtpAu 543HEYv0wcfPPloh4hZJZmQv3N3hFw2ErdhnKnI3fPHxx9mCjigni6n9ggmpKqpd aDi+802dZdKdYld8wtBdnllWJ1XpfuEH/4ZUb/eaEV8ILAcF3mMwtCLJfcV+QK0l XkJmdyzabm86ZpndWdOTJzDkFDK2bqrX8dbiORrC6yz+NHZceh0tK5Go5BsAYELr VjidzES5qZY9+Rzu4S2p0MEoNkauDkKIId7DzhtgXMSUbQJs04NdWF0hSiLotjOX mnNlEpZwS09Vx2/H8ZUgJ5xqODj2a3tQCxg4nIiOaXXFxhtH693oeEg/9JBRaWFp 3tmRJcNqFX9PFd6exlayNJI8SXS3ZpxDVw6pP1cIBc+Zprkh703sYj7Q7w84TMGV dRQUYiZPlfehTvDbbTVaPVmZ3QXinZpR3L/IHDzKoKPud0Qw6Ao= =0jhj -----END PGP SIGNATURE----- Merge tag 'gpio-fixes-for-v7.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux Pull gpio fixes from Bartosz Golaszewski: - fix a memory leak in gpio-sloppy-logic-analyzer - fix a regression in GPIO hog handling for hogs without direction specified - extend the critical section in IRQ handling in gpio-pca953x to cover the reads from the direction register - disable the interrupt on errors when restoring context in gpio-pca953x - apply the initial value when setting direction in gpio-by-pinctrl - use raw spinlock for the register lock in gpio-pch to address locking context issues * tag 'gpio-fixes-for-v7.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: gpio: pch: use raw_spinlock_t for the register lock gpio: pca953x: fix cache_only and IRQ state on restore_context() failure gpio: gpio-by-pinctrl: Apply initial value in direction output wrapper gpio: pca953x: fix pca953x_irq_bus_sync_unlock regmap lock gpiolib: tolerate gpio-hogs lacking a hogging state gpio: sloppy-logic-analyzer: Fix memory leak in gpio_la_poll_probe() |
||
|
Linus Torvalds
|
b96890b3e5 |
powerpc fixes for 7.2 #3
- Ensure vpa,slb_shadow & dtl are unregistered during crash - fix nap return address corruption on async interrupt exit in 970 platform - Fix exit_flags field placement in pt_regs for ptrace - Fix map failure path in dma_ioc0_map_pages() in ps3 platfrom - MAINTAINERS: Demote myself to reviewer - misc fixes and cleanup Thanks to: Amit Machhiwal, Andreas Schwab, Anushree Mathur, Athira Rajeev, Christophe Leroy (CS GROUP), Dmitry V. Levin, Geert Uytterhoeven, John Ogness, Michael Ellerman, Mukesh Kumar Chaurasiya (IBM), Ritesh Harjani (IBM), Thorsten Blum, Vaibhav Jain -----BEGIN PGP SIGNATURE----- iQIzBAABCgAdFiEEqX2DNAOgU8sBX3pRpnEsdPSHZJQFAmpq5/gACgkQpnEsdPSH ZJR3NQ//d2RIqe/XzW6VOoU0k0KS0mldkj8B8pykkO1XgsWRirJNdq4l+/DNwfsq OpIaB7dHoDQP8NIbruYC6tDnDLsEpaQMR6SIr2EeH4H5xHQWUKLiFRQMKOhdzujy MHc6EzazEFjW2/ItbcxLOkW8+zhP5K02Zwmj/sF9hsSKFTq4dAnc9LX8OunJfEbz /JTXS+SK+Z4BQmDlL22b5rEk432zFtvE33Dw0401Vdsn3x/dEKpynlc1LTdbHJXL rkmt3Kc41SnQlFBSO2NzKs6lzz1kQYSC3DdlYOwQ1evvBNqdhzMotg0jKOXFC3C7 m4FbJKpQjTXHhtJZx4+Vrr5k4MFp6fUg5LIbe+rBeN8Ckgk3Yj7qCw8UVjlXyUTp KlkqG6J1Eteg3KMGQClZzZz0kyqWrSsnO7eR8O41wSRmAv27vBxsn9nOKBHcV9Cq gzG0IJTIP+4/qTbXhUjBQLlgRpoCjz5UnmAbisKHBXGUI+wz58Uhf2b8/M53RH1b qnrb81Vp6nLEtPJrjRXeCwYnTRT4qQ8ON9PB1uAIImG8phdxfsfhTivftLJVQqUA DGjFNLpbME2WbyLd0YxDj8jzHp1845/vR+jwyHMQAoQHFJjvAf4/RZ58zKVUtFVR susxnX6YodNMfZisVwcZTaj1pds8YSz72gOE44Qn0K3YjqAej9w= =On4C -----END PGP SIGNATURE----- Merge tag 'powerpc-7.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc fixes from Madhavan Srinivasan: - ensure vpa,slb_shadow & dtl are unregistered during crash - fix nap return address corruption on async interrupt exit in 970 platform - fix exit_flags field placement in pt_regs for ptrace - fix map failure path in dma_ioc0_map_pages() in ps3 platfrom - MAINTAINERS: Michael Ellerman demotes himself to reviewer - misc fixes and cleanup Thanks to Amit Machhiwal, Andreas Schwab, Anushree Mathur, Athira Rajeev, Christophe Leroy (CS GROUP), Dmitry V. Levin, Geert Uytterhoeven, John Ogness, Michael Ellerman, Mukesh Kumar Chaurasiya (IBM), Ritesh Harjani (IBM), Thorsten Blum, and Vaibhav Jain * tag 'powerpc-7.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: MAINTAINERS: Demote myself to reviewer powerpc/serial: Fix include guard comment powerpc/perf: Use strstarts() to simplify is_thread_imc_pmu() powerpc/ps3: Fix map failure path in dma_ioc0_map_pages() powerpc/ps3: Remove unused struct table in setup_areas() powerpc/boot: Fix treeboot-akebono CPU node lookup check powerpc/boot: Fix treeboot-currituck CPU node lookup check powerpc/boot: Fix simpleboot CPU node lookup check powerpc: Fix exit_flags field placement in pt_regs for ptrace powerpc/970: fix nap return address corruption on async interrupt exit powerpc/pseries: Skip vpa_init() for boot cpu in smp_setup_cpu() powerpc/pseries: Ensure vpa,slb_shadow & dtl are unregistered during crash |
||
Denis V. Lunev
|
451c9075d6 |
qede: sync udp_tunnel ports outside qede_lock in the recovery path
A TX timeout on a qede NIC that has VXLAN/GENEVE tunnel ports
configured wedges the rtnetlink control plane of the whole machine:
NETDEV WATCHDOG: ens6f1 (qede): transmit queue 2 timed out 10226 ms
[qede_tx_timeout:586(ens6f1)]TX timeout on queue 2!
[qede_recovery_handler:2665(ens6f0)]Starting a recovery process
The recovery path deadlocks on the driver's own mutex:
qede_sp_task
rtnl_lock()
mutex_lock(&edev->qede_lock) <- taken
qede_recovery_handler
qede_load
udp_tunnel_nic_reset_ntf
__udp_tunnel_nic_device_sync
info->sync_table == qede_udp_tunnel_sync
mutex_lock(&edev->qede_lock) <- same task: deadlock
The mutex is not recursive, so the kworker blocks on itself with
rtnl_lock held, and neither lock is ever released. Every task that
calls rtnl_lock() afterwards (ip, ovs-vswitchd, lldpad, IPv6
addrconf, sshd) blocks forever while the node still answers ping.
In a vmcore from an affected production node rtnl_mutex.owner
decodes to the very kworker blocked at the innermost mutex_lock()
above.
Re-sync the tunnel ports from qede_sp_task() after the internal lock
is dropped, still under rtnl_lock as the udp_tunnel API requires.
This mirrors qede_open(), which calls udp_tunnel_nic_reset_ntf()
under rtnl without the internal lock.
qede_recovery_handler() now returns whether it has successfully
reloaded an open device, and the caller re-syncs the ports only in
that case. This keeps the old gating exactly: a device that was down
or a failed recovery returns false, as those paths never reached the
udp_tunnel_nic_reset_ntf() call before either.
This was the only user of the qede_lock()/qede_unlock() helpers, so
remove them.
Fixes:
|
||
Paolo Abeni
|
c92922c02c |
linux-can-fixes-for-7.2-20260729
-----BEGIN PGP SIGNATURE-----
iIkEABYKADEWIQSl+MghEFFAdY3pYJLMOmT6rpmt0gUCamnRyhMcbWtsQHBlbmd1
dHJvbml4LmRlAAoJEMw6ZPquma3SS00A/Rpm6GVkF0ievxaEWz5no+Vojn2U/S7K
3ix+pFFfrnyTAP9CfWhg8aIkLOF19RXhKRRLDIm5vI8qKCqrqBkSZszJCw==
=Qoox
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-7.2-20260729' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2026-07-29
this is a pull request of 20 patches for net/main.
The first 2 patches fix problems in the CAN J1939 protocol and are by
Tetsuo Handa and Oleksij Rempel.
The next 2 patches fix problems in the CAN ISOTP protocol and are by
Oliver Hartkopp and Minhong He.
Avi Weiss contributes contributed 4 fixes for the ctucanfd, Pengpeng
Hou's patch adds a missing MODULE_DEVICE_TABLE.
The patches for the peak_usb driver are contributed by James Gao,
Maoyi Xie, Maoyi Xie and add sanity checks for the USB bulk data
parsing and fix a double free.
2 fixes for the kvaser_usb driver are provided by Abdun Nihaal and
Pengpeng Hou, a mem leak is fixed and sanity checks for the USB bulk
data parsing.
Tu Nguyen's patch for the rcar_canfd driver fixes the initializing
flow.
Pengpeng Hou contributes a patch for the softing driver to validate
the firmware record spans.
Lucas Martins Alves's patch for the c_can driver keeps the controller
in init mode until configuration is complete.
A patch by my add missing URB resubmission on skb allocation failure
to the gs_usb driver.
Guangshuo Li's patch for the etas_es58x driver fixes a RX buffer leak.
The last patch is by Pengpeng Hou and adds sanity checks to the USB
bulk data parsing of the ems_usb driver.
linux-can-fixes-for-7.2-20260729
* tag 'linux-can-fixes-for-7.2-20260729' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: ems_usb: validate CPC message lengths
can: etas_es58x: es58x_read_bulk_callback(): fix RX buffer leak on URB resubmit failure
can: gs_usb: gs_usb_receive_bulk_callback(): resubmit URB on skb allocation failure
can: c_can: c_can_chip_config(): keep controller in init mode until bittiming is configured
can: softing: fw_parse(): validate firmware record spans
can: rcar_canfd: change the initializing flow for clocks and resets
can: kvaser_usb_leaf: kvaser_usb_leaf_wait_cmd(): validate received command extents
can: kvaser_usb: kvaser_usb_hydra_get_busparams(): fix memory leak in kvaser_usb_hydra_get_busparams()
can: peak_usb: validate uCAN receive record lengths
can: peak_usb: peak_usb_start(): fix double free of transfer buffer on URB submit error
can: peak_usb: add bounds check for USB channel index
can: ctucanfd: add missing MODULE_DEVICE_TABLE()
can: ctucanfd: use self-test mode for PRESUME_ACK
can: ctucanfd: handle bus error interrupts
can: ctucanfd: mark error-active controller status valid
can: ctucanfd: unmap BAR0 using base address
can: isotp: check register_netdevice_notifier() error in module init
can: isotp: fix timer drain order, wakeup handling and tx_gen ordering
can: j1939: transport: j1939_session_fresh_new(): initialize receive buffer
can: j1939: use netdevice_tracker for j1939_{priv,session,ecu} tracking
====================
Link: https://patch.msgid.link/20260729102802.505168-1-mkl@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|