They are not used anywhere, so safe to drop.
Signed-off-by: Oleg Drokin <oleg.drokin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SEEK_DATA and SEEK_HOLE are always defined in the kernel,
drop the definition checks
Signed-off-by: Oleg Drokin <oleg.drokin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Card configuration is stored in SPI EEPROM (93c46 or 93c56)
working in 128|256x16 mode.
Communication is handled using GPIO bitbang.
>From behaviour perspective, delay after read was removed.
It is not needed as we wait after reading GPIO mapped to
PCI-E register - it should have no side effects.
According to sample EEPROM datasheet (AT93Cx6), max frequency for
worst case scenario (1.8V supply) is 250kHZ (vs. 1MHz for 5V).
Driver generates ~50kHZ clock - margin should be big enough
even for devices from other vendors.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to unisys, the s_par hypervisor has a bug in which it never
triggers an interrupt. That makes the visornic effectively a 2ms poll
loop. In order to just have the rx thread shceduling a napi poll every
2ms, lets instead give it the chance to check the response queue for
data before we schedule. This helper provides that functionality
Signed-off-by: Neil Horman <nhorman@redhat.com>
Signed-off-by: Benjamin Romer <benjamin.romer@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass platform_data as an argument to fbtft_framebuffer_alloc()
instead of using dev->platform_data.
This fixes an issue where the device comes from Device Tree
and fbtft_probe_common() sets dev->platform_data to allocated
memory. When the module is reloaded, dev->platform_data points
to freed memory.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix build of hdm-dim2. Since it calls a function that is provided
by AIM_NETWORK, make it depend on that symbol.
Also fix a misspelling in the Kconfig file.
drivers/built-in.o: In function `deliver_netinfo_thread':
dim2_hdm.c:(.text+0x3a9563): undefined reference to `most_deliver_netinfo'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jain Roy Ambi <JainRoy.Ambi@microchip.com>
Cc: Andrey Shvetsov <andrey.shvetsov@k2l.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix build errors: driver uses snd_pcm*() interfaces, so select
SND_PCM.
drivers/built-in.o: In function `audio_rx_completion':
sound.c:(.text+0x3cd376): undefined reference to `snd_pcm_period_elapsed'
drivers/built-in.o: In function `pcm_prepare':
sound.c:(.text+0x3cd3b0): undefined reference to `snd_pcm_format_physical_width'
sound.c:(.text+0x3cd3ce): undefined reference to `snd_pcm_format_big_endian'
sound.c:(.text+0x3cd42c): undefined reference to `snd_pcm_format_big_endian'
drivers/built-in.o: In function `pcm_hw_free':
sound.c:(.text+0x3cd50a): undefined reference to `snd_pcm_lib_free_vmalloc_buffer'
drivers/built-in.o: In function `pcm_hw_params':
sound.c:(.text+0x3cd54c): undefined reference to `_snd_pcm_lib_alloc_vmalloc_buffer'
drivers/built-in.o: In function `playback_thread':
sound.c:(.text+0x3cd6a0): undefined reference to `snd_pcm_period_elapsed'
drivers/built-in.o: In function `audio_probe_channel':
sound.c:(.text+0x3cdc0b): undefined reference to `snd_pcm_new'
sound.c:(.text+0x3cdc2b): undefined reference to `snd_pcm_set_ops'
drivers/built-in.o:(.data+0x952d0): undefined reference to `snd_pcm_lib_ioctl'
drivers/built-in.o:(.data+0x95318): undefined reference to `snd_pcm_lib_get_vmalloc_page'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Christian Gromm <christian.gromm@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch prevents a potential integer overlow.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christian Gromm <christian.gromm@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HBM 2.0 version for Sunrise point Skylake (PCH) based devices
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A BIOS may put the device in d0i3 on platform initialization so it won’t
consume power even if the driver is not present, in turn the driver has
to wake up the devices on load in order to perform the initialization
sequence and move it back to low power state on driver remove.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move mei_me_hw_reset down in the source file to avoid
forward declarations when introducing d0i3 flow in the next patch.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rework mei power gating state machine to support entry and exit to and
from D0i3 power state.
The choice between legacy and D0i3 routines is conditioned on
d0i3_supported flag.
The patch introduces warning:
drivers/misc/mei/hw-me.c:901:12: warning: ‘mei_me_d0i3_enter’ defined but not used [-Wunused-function]
it will go away in consequent patch
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before adding support for D0i3 we need to reorganize the hbm pg handling
Move HBM PG response code to dedicated functions in order to unclutter
hbm command switch.
Add check for the right system state before message processing and
return -EPROTO in state mismatch case.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
D0i3 adds additional interrupt reason bit, therefore we add a variable
intr_source to save the interrupt causes for further dispatching.
The interrupt cause is saved in the irq quick handler to achieve
unified behavior for both MSI enabled and shared interrupt platforms.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Detect d0i3 low power state during hw configuration,
the value is set in HFS_1 pci config reigister.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with Intel Sunrisepoint (Skylake PCH) the MEI device
supports D0i3 low power state. Add D0i3 control registers.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device can return error 5 (NOT_ALLOWED) on connection attempt.
This error can happen if:
1. An another connection attempt is in progress
2. There is an attempt to connect a fixed (connectionless) client
3. The number of available connections is exceeded (new in HBM 2.0)
We should not hit that error unless there is an internal book keeping
hiccup except option (3), therefore we translate the error code
to errno EBUSY;
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable drivers on mei client bus to subscribe
to asynchronous event notifications.
Introduce events_mask to the existing callback infrastructure
so it is possible to handle both RX and event notification.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A process can be informed about client notification also via
SIGIO with POLL_PRI event.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Polling on priority events is translated on waiting for event
notification. One need to enable notification prior for
calling select or poll system call otherwise process
will not wait.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ioctl IOCTL_MEI_NOTIFY_SET for enabling and disabling
async event notification.
Add ioctl IOCTL_MEI_NOTIFY_GET for receiving and acking
an event notification.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mei_cl_notify_get is to be called by a host client
to wait, receive, and ack the event notification.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add per client notification request infrastructure
that allows client to enable or disable async
event notification.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only FW version 2.0 and newer support the async event
notification. For backward compatibility block the feature
if the FW version is older then 2.0
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement sending and reception handlers for the
async event notification hbm commands.
Add client notification book keeping data required for the messages
notify_en to indicate whether notification is enabled
notify_ev to indicate whether an event is pending
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FW has gained new capability where a FW client can asynchronously
notify the host that an event has occurred in its process.
The notification doesn't provide any data and host may need to query
further the FW client in order to get details of the event.
Host can subscribe or unsubscribe to the event notification via
designated HBM commands, and also the notification is carried on
a new HBM command.
This patch adds definitions of asynchronous notification HBM commands.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the FW with HBM version >= 2.0 we don't need to reset the whole
device in case of a particular client failing to connect, it is enough
to send disconnect a request to bring the device to the stable state.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HBM version 2.0 and above allows ME clients in the system to
register/unregister after the system is fully initialized.
Clients may be added or removed after enum_resp message was
received
1. To preserve backward compatibility the driver can opt-in to receive
client add messages by setting allow_add field in enum_req
2. A new client is added upon reception of MEI_HBM_ADD_CLIENT_REQ_CMD
3. A client is removed in a lazy manner when connection request
respond with MEI_HBMS_CLIENT_NOT_FOUND status
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MEI bus was designed around nfc and was hard to extend.
Instead of the hard coded way of adding the devices on the mei bus
we scan the whole me client list and create a device for each
eligible me client (mei_cl_bus_rescan); currently we support
only clients with single connection and fixed address clients.
NFC radio name detection is run as a fixup routine
The patch replaces handling the device list based on struct me_cl
to device list based on me_cl_devices. The creating a connection
is pushed from the device creation time to device enablement.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the dependency on struct ndev from the nfc device
name creation function so it is possible to use it
in a fixup routine
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we support only clients with single connection
and fixed address clients so all other clients are blacklisted
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Blacklist nfc info client which is only used for retrieval
of the NFC radio version
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split the device registration into allocation and device struct
initialization, device setup, and the final device registration.
This why it is possible to run fixups and quirks during the setup stage
on an initialized device. Each fixup routine effects do_match flag.
If the flag is set to false at the end the device won't be
registered on the bus.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of holding the list of host clients (me_cl)
we want to keep the list me client devices (mei_cl_device)
This way we can create host to me client connection only when needed.
Add list head to mei_cl_device and cl_bus_lock
Add bus_added flag to the me client (mei_me_client) to track if
the appropriate mei_cl_device was already created and is_added
flag to mei_cl_device to track if it was already added to the device
list across the bus rescans
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add reference to the bus device (mei_device) for easier access.
To ensures that referencing cldev->bus is valid during cldev life time
we increase the bus ref counter on a client device creation and drop it
on the device release.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of generating device id on the fly during probing we
find the matching id entry on the device id table.
Get bus the module reference counter so it cannot
be unloaded after the driver has bounded to the client
device
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mei_cl_device_match now calls mei_cl_device_find that returns
the matching device id in the device id table.
We will utilize the mei_cl_device_find during probing
to locate the matching entry.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If event registeration has failed, the caller should know
about it.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not enable events implicitly in mei_cl_enable_device, it should be
done explicitly using mei_cl_register_event_cb so the events
are enabled only when needed.
The NFC drivers has been already using it that way so no need for
further changes just remove the code from mei_cl_enable_device.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename mei_cl_uevent to mei_cl_device_uevent to match
the naming convention of mei_cl_bus_type functions
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To make the file more organize move mei client driver api
to the start of the file and add Kdoc.
There are no functional changes in this patch.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bus-fixup.c will be a place for fixups and quirks
for all types of me client devices.
As for now it contians only the fixup for setting
the nfc device name on the me client bus.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the mei bus layer there is use of different variables
of driver and device types with no clear naming convention.
There are generic struct device and struct driver,
then mei_cl_{device, driver}, and finally mei_device which
in this context serves as a bus device.
The patch sets following naming convention:
the variables of type struct device remains dev
the variables of type struct driver remains drv
the variables of type struct mei_cl_device are now cldev
the variables of type struct mei_cl_driver are now cldrv
the variables of type struct mei_device are now bus, in bus
layer context
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mei_cl_write function is giving up on a write cb ownership after it
was sent or queued. The write cb is then freed in the completion
handler. Especially during blocking write mei_cl_write function waits
for the completion handler and then access the freed memory to fetch the
written size. The quick fix is to store the buffer size prior to
sending, the size is not altered during the flow.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PM_RUNTIME has been replaced with PM by commit 464ed18ebd ("PM:
Eliminate CONFIG_PM_RUNTIME") hence substitute the reference on
PM_RUNTIME with PM and re-arrange the text to 80 column break.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Until now, checkkonfigsymbols.py did not check default statements for
references on missing Kconfig symbols (i.e., undefined Kconfig options).
Hence, add support to parse and check the Kconfig default statement.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Color output to make it more readable. Symbols will be printed yellow,
relevant commits (see --find) red.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Acked-by: Stefan Hengelein <stefan.hengelein@fau.de>
Acked-by: Andreas Ruprecht <andreas.ruprecht@fau.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
