If the retransmission in CA_Loss is lost again, we should not
continue to slow start or raise cwnd in congestion avoidance mode.
Instead we should enter fast recovery and use PRR to reduce cwnd,
following the principle in RFC5681:
"... or the loss of a retransmission, should be taken as two
indications of congestion and, therefore, cwnd (and ssthresh) MUST
be lowered twice in this case."
This is especially important to reduce loss when the CA_Loss
state was caused by a traffic policer dropping the entire inflight.
The CA_Loss state has a problem where a loss of L packets causes the
sender to send a burst of L packets. So a policer that's dropping
most packets in a given RTT can cause a huge retransmit storm. By
contrast, PRR includes logic to bound the number of outbound packets
that result from a given ACK. So switching to CA_Recovery on lost
retransmits in CA_Loss avoids this retransmit storm problem when
in CA_Loss.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 9a0e609e3f.
(Resolved a conflict during revert due to commit bfebd1cdb4 that came
after)
This revert is motivated by a couple failure reports on request-based DM
multipath testbeds:
1) Netapp reported that their multipath fault injection test under heavy
IO load can stall longer than 300 seconds.
2) IBM reported elevated lock contention in their testbed (likely due to
increased back pressure due to IO not being dispatched as quickly):
https://www.redhat.com/archives/dm-devel/2015-July/msg00057.html
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 4.1+
For the best performance the headphone path enable/disable must be
handled specially for the situations of DRE on and DRE off.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a register patch for rev E and above that configures the location of
some write sequences to assist with the headphone enables.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This register will be needed as part of some additional support for the
headphone path on wm5110, so this patch adds the register and sets up
its regmap config.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
int_ret_from_sys_call now expects IRQs to be enabled. I got
this right in the real sysexit_audit and sysretl_audit asm
paths, but I missed it in the #defined-away versions when
CONFIG_AUDITSYSCALL=n. This is a straightforward fix for
CONFIG_AUDITSYSCALL=n
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 29ea1b258b ("x86/entry/64: Migrate 64-bit and compat syscalls to the new exit handlers and remove old assembly code")
Link: http://lkml.kernel.org/r/25cf0a01e01c6008118dd8f8d9f043020416700c.1436291493.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Use the card field of a component to indicate whether it is bound or not.
This makes a certain sense given that the field contains the card the
component is bound to and a component can only be bound to one card at a
time. And it also requires to unset the card field when the component is
unbound from the card.
This makes the probded flag redundant and it can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
A component can only be bound to a single card at a time. Binding it to
card while it is already bound to another will result in undefined
behavior.
As the undefined behavior might only manifest itself later on it is not
necessarily always straight forward to find the cause. To prevent this add
a check that refuses to bind a component to multiple cards as well as
prints a error describing the problem.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
We will add SKL platform data. So organizing common and platform
specific data helps.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts ed043aebe6 ("ASoC: wm8996: Pass the IRQF_ONESHOT flag").
The coccinelle warnings is false positive because the original code does
set IRQF_ONESHOT by "trigger |= IRQF_ONESHOT;".
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts 3d907cc30d ("ASoC: wm5100: Pass the IRQF_ONESHOT flag").
The coccinelle warnings is false positive because the original code does
set IRQF_ONESHOT by "trigger |= IRQF_ONESHOT;".
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts 58d4683286 ("ASoC: wm0010: Add missing IRQF_ONESHOT").
The coccinelle warnings is false positive because the original code does
set IRQF_ONESHOT by "trigger |= IRQF_ONESHOT;".
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
dmi_check_system() takes "const struct dmi_system_id *", so make the
dmi_system_id table const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse complains that sst_platform_compr_ops should be static, but the
declaration of this symbol was not correct so declare the symbol as
extern in header file
sound/soc/intel/atom/sst-mfld-platform-compress.c:257:22: warning: symbol
'sst_platform_compr_ops' was not declared. Should it be static?
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse complains that sst_slot_enum_info should be static, so make it
static
sound/soc/intel/atom/sst-atom-controls.c:135:5: warning: symbol
'sst_slot_enum_info' was not declared. Should it be static?
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SND_SOC_INTEL_SST is for common IPC lib and this should ideally be
not selectable symbol but selected by respective machine driver So
remove the prompt and get respective machines select it
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some HSW and BYT machines depend on the DW_DMAC_CORE so they should
have have depends on this symbol rather than common IPC lib as SKL
onwards IPC lib is used but we don't depend on DW_DMAC_CORE
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Intel boards directory was under CONFIG_SND_SOC_INTEL_SST so the
machines which don't need these were not allowed to be
selected/compiled without enabling this symbol The machine should be
allowed to selected by ASoC and then they should select rest of
symbols required
Reported-by: Michele Curti <michele.curti@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After suspend -> resume the ts3a227e_interrupt sometimes comes before i2c
controller resume is called .regmap_read will return incorrect status
and report a wrong jack status.This patch will disable irq on suspend
and enable irq again on the resume to make sure interrupt is coming
after TI resumes. Also We should return if there is read err,the
interrupt will come again since it is level triggered and we are not yet
clear the interrupt.
In addtion,cht_bsw_max98090_ti machine driver registered additional
notifier base on jack event which will program the audio codec.there
will be codec timeout err if such event occurs prior to i2c controller
is resumed.
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently we enable debug exceptions before reading ESR_EL1 in both
el0_inv and el1_inv. If a debug exception is taken before we read
ESR_EL1, the value will have been corrupted.
As el*_inv is typically fatal, an intervening debug exception results in
misleading debug information being logged to the console, but is not
otherwise harmful.
As with the other entry paths, we can use the ESR_EL1 value stashed
earlier in the exception entry (in x25 for el0_sync{,_compat}, and x1
for el1_sync), giving us better error reporting in this case.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The "if (pass_size > buf->total)" can underflow so I have changed the
type of size and pass_size to unsigned to avoid this problem.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Newer ASICs have more VRAM on average and allocating more GART as
well can have advantages. Also see commit edcd26e8.
Ideally, we should scale GART size based on actual VRAM size, but
that requires significant restructuring of initialization.
v2: extract small helper, apply to error paths
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This was regressed by commit 39e7f6f8, although I don't know of any
actual issues caused by it.
The storage domain is read without TTM locking now, but the lock
never helped to prevent any races.
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We don't need to call the (expensive) radeon_bo_wait, checking the
fences via RCU is much faster. The reservation done by radeon_bo_wait
does not save us from any race conditions.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is a translation of the patch ...
"drm/radeon: Handle irqs only based on irq ring, not irq status regs."
... for the vblank irq handling, to fix the same problem described
in that patch on the new driver.
Only compile tested due to lack of suitable hw.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
CC: Michel Dänzer <michel.daenzer@amd.com>
CC: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Trying to resolve issues with missed vblanks and impossible
values inside delivered kms pageflip completion events showed
that radeon's irq handling sometimes doesn't handle valid irqs,
but silently skips them. This was observed for vblank interrupts.
Although those irqs have corresponding events queued in the gpu's
irq ring at time of interrupt, and therefore the corresponding
handling code gets triggered by these events, the handling code
sometimes silently skipped processing the irq. The reason for those
skips is that the handling code double-checks for each irq event if
the corresponding irq status bits in the irq status registers
are set. Sometimes those bits are not set at time of check
for valid irqs, maybe due to some hardware race on some setups?
The problem only seems to happen on some machine + card combos
sometimes, e.g., never happened during my testing of different PC
cards of the DCE-2/3/4 generation a year ago, but happens consistently
now on two different Apple Mac cards (RV730, DCE-3, Apple iMac and
Evergreen JUNIPER, DCE-4 in a Apple MacPro). It also doesn't happen
at each interrupt but only occassionally every couple of
hundred or thousand vblank interrupts.
This results in XOrg warning messages like
"[ 7084.472] (WW) RADEON(0): radeon_dri2_flip_event_handler:
Pageflip completion event has impossible msc 420120 < target_msc 420121"
as well as skipped frames and problems for applications that
use kms pageflip events or vblank events, e.g., users of DRI2 and
DRI3/Present, Waylands Weston compositor, etc. See also
https://bugs.freedesktop.org/show_bug.cgi?id=85203
After some talking to Alex and Michel, we decided to fix this
by turning the double-check for asserted irq status bits into a
warning. Whenever a irq event is queued in the IH ring, always
execute the corresponding interrupt handler. Still check the irq
status bits, but only to log a DRM_DEBUG message on a mismatch.
This fixed the problems reliably on both previously failing
cards, RV-730 dual-head tested on both crtcs (pipes D1 and D2)
and a triple-output Juniper HD-5770 card tested on all three
available crtcs (D1/D2/D3). The r600 and evergreen irq handling
is therefore tested, but the cik an si handling is only compile
tested due to lack of hw.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
CC: Michel Dänzer <michel.daenzer@amd.com>
CC: Alex Deucher <alexander.deucher@amd.com>
CC: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The "fix" in commit 0b08c5e594 ("audit: Fix check of return value of
strnlen_user()") didn't fix anything, it broke things. As reported by
Steven Rostedt:
"Yes, strnlen_user() returns 0 on fault, but if you look at what len is
set to, than you would notice that on fault len would be -1"
because we just subtracted one from the return value. So testing
against 0 doesn't test for a fault condition, it tests against a
perfectly valid empty string.
Also fix up the usual braindamage wrt using WARN_ON() inside a
conditional - make it part of the conditional and remove the explicit
unlikely() (which is already part of the WARN_ON*() logic, exactly so
that you don't have to write unreadable code.
Reported-and-tested-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Paul Moore <pmoore@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hisilicon SMMUv3 devices treat CMD_PREFETCH_CONFIG as a illegal command,
execute it will trigger GERROR interrupt. Although the gerror code manage
to turn the prefetch into a SYNC, and the system can continue to run
normally, but it's ugly to print error information.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
[will: extended binding documentation]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Because we will choose the minimum value between STRTAB_L1_SZ_SHIFT and
IDR1.SIDSIZE, so enlarge STRTAB_L1_SZ_SHIFT will not impact the platforms
whose IDR1.SIDSIZE is smaller than old STRTAB_L1_SZ_SHIFT value.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The arm64 CPU architecture defines TCR[8:11] as holding the inner and
outer memory attributes for TTBR0.
This patch fixes the ARM SMMUv3 driver to pack these bits into the
context descriptor, rather than picking up the TTBR1 attributes as it
currently does.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
STRTAB_BASE_CFG.LOG2SIZE should be set to log2(entries), where entries
is the *total* number of entries in the stream table, not just the first
level.
This patch fixes the register setting, which was previously being set to
the size of the l1 thanks to a multi-use "size" variable.
Reported-by: Zhen Lei <thunder.leizhen@huawei.com>
Tested-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The element size of cfg->strtab is just one DWORD, so we should use a
multiply operation instead of a shift when calculating the level 1
index.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Fengguang Wu's tests triggered a bug in the branch tracer's start up
test when CONFIG_DEBUG_PREEMPT set. This was because that config
adds some debug logic in the per cpu field, which calls back into
the branch tracer.
The branch tracer has its own recursive checks, but uses a per cpu
variable to implement it. If retrieving the per cpu variable calls
back into the branch tracer, you can see how things will break.
Instead of using a per cpu variable, use the trace_recursion field
of the current task struct. Simply set a bit when entering the
branch tracing and clear it when leaving. If the bit is set on
entry, just don't do the tracing.
There's also the case with lockdep, as the local_irq_save() called
before the recursion can also trigger code that can call back into
the function. Changing that to a raw_local_irq_save() will protect
that as well.
This prevents the recursion and the inevitable crash that follows.
Link: http://lkml.kernel.org/r/20150630141803.GA28071@wfg-t540p.sh.intel.com
Cc: stable@vger.kernel.org # 3.10+
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This will be useful to PSR and FBC once we start making
dirty fb calls to also flush frontbuffer.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
wa_ctx_emit() depends on the name of a local variable; if the name of that
variable is changed then we get compile errors. In this case it is unlikely
to be changed as this macro is only used in this set of functions but
Kernel coding guidelines doesn't recommend doing this. It was my mistake
as I should have corrected it at the beginning but missed so correct
this before there are more usages of this macro (Bob Beckett).
https://www.kernel.org/doc/Documentation/CodingStyle,
Chapter 12, "Things to avoid when using macros", point 2):
"
2) macros that depend on having a local variable with a magic name:
#define FOO(val) bar(index, val)
might look like a good thing, but it's confusing as hell when one reads the
code and it's prone to breakage from seemingly innocent changes.
"
v2: Optimization to avoid multiple evaluation of 'index' in the macro.
Since we invoke it multiple times, compiler, if it can, should be able to coalesce
them into a single condition and remove multiple WARN_ON checks (Chris).
Suggested-by: Robert Beckett <robert.beckett@intel.com>
Cc: Robert Beckett <robert.beckett@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Writing to PCH_PORT_HOTPLUG for each interrupt is not required.
Handle it only if hpd has actually occurred like we handle other
interrupts.
v2: Make few variables local to if block (Ville)
v3: Add check for ibx/cpt both (Ville).
While at it, remove the redundant check for hotplug_trigger from
pch_get_hpd_pins
v4: Indentation (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If CONFIG_PM is not set the PU power domain needs to be enabled always,
otherwise there are two failure scenarios which will hang the system if
one of the devices in the PU domain is accessed.
1. New DTs (4.1+) drop the "always-on" property from the PU regulator, so
if it isn't properly enabled by the GPC code it will be disabled at the
end of boot.
2. If the bootloader already disabled the PU domain the GPC explicitly
needs to enable it again, even if the kernel doesn't do any power
management. This is a bit hypothetical, as it requires to boot a
mainline kernel on a downstream bootloader, as no mainline bootloader
disables the PM domains.
Cc: <stable@vger.kernel.org> # 4.1
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since
commit 8c7b5ccb72
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Tue Apr 21 17:13:19 2015 +0300
drm/i915: Use atomic helpers for computing changed flags
we compute the plane state for a modeset before actually committing
any changes, which means crtc->active won't be correct yet. Looking at
future work in the modeset conversion targetting 4.3 the only places
where crtc_state->active isn't accurate is when disabling other CRTCs
than the one the modeset is for (when stealing connectors). Which
isn't the case here. And that's also confirmed by an audit, we do
unconditionally update crtc_state->active for the current pipe.
We also don't need to update any other plane check functions since we
only ever add the primary state to the modeset update right now.
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was lost in
commit ce22dba92d
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Tue Apr 21 17:12:56 2015 +0300
drm/i915: Move toggling planes out of crtc enable/disable.
and we still need that crtc->active check since the overall modeset
flow doesn't yet take dpms state into account properly. Fixes WARNING
backtraces on at least bdw/hsw due to the ips disabling code being
upset about being run on a switched-off pipe.
We don't need a corresponding change on the enable side since with the
old setCrtc semantics we always force-enable the pipe after a modeset.
And the dpms function intel_crtc_control already checks for ->active.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we switch clock events to timer 3 we will have more bits to
use and can sleep longer when using NO_HZ.
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The timer has no business using __raw accessors, in this case
the readl/writel makes perfect sense as the changes really need
to hit these registers before we continue.
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the EP93xx to use GENERIC_CLOCKEVENTS and
CLKSRC_MMIO. Also implements a sched_clock() hook.
Tested on the SIM.ONE. Use only oneshot events.
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This breaks the timer code out of the core file in preparation
for refactoring.
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Vinson reported shadow declaration of close introduced
by the following commit:
106a94a0f8 perf stat: Introduce read_counters function
Using close_counters name instead.
Reported-by: Vinson Lee <vlee@twopensource.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Fixes: 106a94a0f8 ("perf stat: Introduce read_counters function")
Link: http://lkml.kernel.org/r/20150708111731.GA3512@krava.redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
