Padding the bitstream buffer is not enough to reliably avoid prefetch
failures. Picture runs with the next buffer's header already visible to
the CODA7541 succeed much more reliably, so always queue two JPEG frames
into the bitstream buffer.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The hardware codec is not colorspace aware. We should trust userspace to
set the correct colorimetry information on the OUTPUT queue and mirror
the exact same setting on the CAPTURE queue.
There is no reason to restrict colorspace to JPEG for JPEG images, if
userspace injects the correct colorspace information into the JPEG
headers after encoding.
Fixes: b14ac54568 ("[media] coda: improve colorimetry handling")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If new buffers are queued after streamoff, the flag will be cleared
anyway, so this is mostly for the purpose of correctness.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In the vivid driver you want gain to continuous change while autogain
is on. However, dev->jiffies_vid_cap doesn't actually change. It probably
did in the past, but changes in the code caused this to be a fixed value
that is only set when you start streaming.
Replace it by jiffies, which is always changing.
[mchehab@kernel.org: use jiffies_to_msecs() instead of dividing by HZ]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Whether reordering should be enabled only depends on the h.264 profile.
Stop parsing the level and drop the debug message, profile and level
can now be determined via read-only decoder controls.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The decoder profile/level controls initially can be used to determine
supported profiles and levels. The values are set for a given stream
once the headers are parsed.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The encoder picture run command takes a picture source stride parameter.
This must be set to the output queue's bytesperline, not width.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When the imx-media driver was initially merged, there was a conflict
with 8d67ae25 ("media: v4l2-ctrls: Reserve controls for MAX217X") which
was not fixed up correctly, resulting in V4L2_CID_USER_MAX217X_BASE and
V4L2_CID_USER_IMX_BASE taking on the same value. Fix by assigning imx
CID base the next available range at 0x10b0.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The vb2_queue will soon be mandatory. The videobuf2 core
will throw a verbose warning if it's not set.
The stk1160 driver is setting the queue lock, but after
the vb2_queue_init call. Avoid the warning by setting
the lock before the queue initialization.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This driver is currently specifying a video_device lock,
which means it is protecting all the ioctls (including
queue ioctls) with a single mutex.
It's therefore straightforward to implement wait_prepare
and wait_finish, by explicitly setting the vb2_queue lock.
Having these callbacks releases the queue lock while blocking,
which improves latency by allowing for example streamoff
or qbuf operations while waiting in dqbuf.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This driver is currently specifying a video_device lock,
which means it is protecting all the ioctls (including
queue ioctls) with a single mutex.
It's therefore straightforward to implement wait_prepare
and wait_finish, by explicitly setting the vb2_queue lock.
Having these callbacks releases the queue lock while blocking,
which improves latency by allowing for example streamoff
or qbuf operations while waiting in dqbuf.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, this driver does not serialize its video4linux
ioctls, which is a bug, as race conditions might appear.
In addition, video_device and vb2_queue locks are now both
mandatory. Add them, and implement wait_prepare and
wait_finish.
To stay on the safe side, this commit uses a single mutex
for both locks. Better latency can be obtained by separating
these if needed.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the device mutex to protect the vb2_queue.
This allows to replace the ad-hoc wait_{prepare, finish}
with vb2_ops_wait_{prepare, finish}.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This driver is currently specifying a vb2_queue lock,
which means it straightforward to implement wait_prepare
and wait_finish.
Having these callbacks releases the queue lock while blocking,
which improves latency by allowing for example streamoff
or qbuf operations while waiting in dqbuf.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the mutex in struct mtk_mdp_ctx to protect the
capture and output vb2_queues. This allows to replace
the ad-hoc wait_{prepare, finish} with
vb2_ops_wait_{prepare, finish}.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, this driver does not serialize its video4linux
ioctls, which is a bug, as race conditions might appear.
In addition, video_device and vb2_queue locks are now both
mandatory. Add them, and implement wait_prepare and
wait_finish.
To stay on the safe side, this commit uses a single mutex
for both locks. Better latency can be obtained by separating
these if needed.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
For m2m devices the vdev->queue lock was always taken instead of the
lock for the specific capture or output queue. Now that we pushed
the locking down into __video_do_ioctl() we can pick the correct
lock and potentially improve the performance of m2m devices.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
imx274_write_table() is a mere wrapper (and the only user) to
imx274_regmap_util_write_table_8(). Remove this useless indirection by
merging the two functions into one.
Also get rid of the wait_ms_addr and end_addr parameters since it does
not make any sense to give them any values other than
IMX274_TABLE_WAIT_MS and IMX274_TABLE_END.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
IMX274_DEFAULT_MODE is defined but not used. Start using it, so the
default can be more easily changed without digging into the code.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
After restructuring struct imx274_frmfmt, the mode_index field is
still in use only for two dev_dbg() calls in imx274_s_stream(). Let's
remove it and avoid duplicated information.
Replacing the first usage requires some rather annoying but trivial
pointer math. The other one can be removed entirely since it would
print the same value anyway.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Data about the implemented readout modes is partially stored in
imx274_formats[], the rest is scattered in several arrays. The latter
are then accessed using the mode index, e.g.:
min_frame_len[priv->mode_index]
Consolidate all these data in imx274_formats[], and store a pointer to
the selected mode (i.e. imx274_formats[priv->mode_index]) in the main
device struct. This way code to use these data becomes more readable,
e.g.:
priv->mode->min_frame_len
This removes lots of scaffolding code and keeps data about each mode
in a unique place.
Also remove a parameter to imx274_mode_regs() that is now unused.
While this adds the mode pointer to the device struct, it does not
remove the mode_index from it because mode_index is still used in two
dev_dbg() calls. This will be handled in a follow-up commit.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The current probe function calls v4l2_ctrl_handler_setup() before
initializing the format info. This triggers call paths such as:
imx274_probe -> v4l2_ctrl_handler_setup -> imx274_s_ctrl ->
imx274_set_exposure, where priv->mode_index is accessed before being
assigned.
This is wrong but does not trigger a visible bug because priv is
zero-initialized and 0 is the default value for priv->mode_index. But
this would become a crash in follow-up commits when mode_index is
replaced by a pointer that must always be valid.
Fix the bug before it shows up by initializing struct members early.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a v4l2 sub-device driver for the ak7375 lens voice coil.
This is a voice coil module using the i2c bus to control the
focus position.
ak7375 can write multiple bytes of data at a time. If more
data is received instead of the stop condition after receiving
one byte of data, the address inside the chip is automatically
incremented and the data is written into the next address.
The ak7375 can control the position with 12 bits value and
consists of two 8 bit registers show as below:
register 0x00(AK7375_REG_POSITION):
+---+---+---+---+---+---+---+---+
|D11|D10|D09|D08|D07|D06|D05|D04|
+---+---+---+---+---+---+---+---+
register 0x01:
+---+---+---+---+---+---+---+---+
|D03|D02|D01|D00|---|---|---|---|
+---+---+---+---+---+---+---+---+
This driver support :
- set ak7375 to standby mode once suspend and
turn it back to active if resume
- set the position via V4L2_CID_FOCUS_ABSOLUTE ctrl
[Sakari Ailus: Rename val as ret in probe, drop redundant error message]
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If a PMU doesn't have any IRQs, we should return 0 from
armpmu_request_irqs(), rather than uninitialised stack.
Signed-off-by: Will Deacon <will.deacon@arm.com>
A hooking API was implemented for 4.17 in fa93854f7a followed
by hooks for Thinkpad laptops in 2801b9683f. The Thinkpad
drivers did not support the Thinkpad 13 and the hooking API crashes
on unsupported batteries by altering a list of hooks during unsafe
iteration. Thus, Thinkpad 13 laptops could no longer boot.
Additionally, a lock was kept in place and debugging information was
printed out of order.
Fixes: fa93854f7a (battery: Add the battery hooking API)
Cc: 4.17+ <stable@vger.kernel.org> # 4.17+
Signed-off-by: Jouke Witteveen <j.witteveen@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add device tree bindings for AKM ak7375 voice coil lens
driver. This chip is used to drive a lens in a camera module.
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Permanently enable the SYNA7500 touchscreen device on the Dell
Venue Pro 7139. The DSDT hides the touchscreen ACPI device on
the 7139 in the same fashion as the 7130, and needs to
be enabled in the same way.
Signed-off-by: Tristian Celestin <tristiancelestin@fastmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Dell Venue Pro 7140 supports the Low Power S0 Idle state, but
does not support any of the _DSM functions that the current heuristic
checks for.
Since suspend-to-mem can not be safely performed on this machine,
and since the bitfield check can't cover this case, it is safer
to enable s2idle by default by checking for the presence of the
_DSM alone and removing the bitfield check.
Signed-off-by: Tristian Celestin <tristiancelestin@fastmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Jani spotted this when reviewing my earlier patch to remove the driver
internal usage of this field in:
Commit 3cf91adaa5 ("backlight: Nuke BL_CORE_DRIVER1")
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The patch 'backlight: pwm_bl: compute brightness of LED linearly to
human eye' introduced a default brightness-levels table that is used
when brightness-levels is not available in the dts. So move
brightness-levels and default-brightness-level to be optional.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When you want to change the brightness using a PWM signal, one thing you
need to consider is how human perceive the brightness. Human perceive
the brightness change non-linearly, we have better sensitivity at low
luminance than high luminance, so to achieve perceived linear dimming,
the brightness must be matches to the way our eyes behave. The CIE 1931
lightness formula is what actually describes how we perceive light.
This patch computes a default table with the brightness levels filled
with the numbers provided by the CIE 1931 algorithm, the number of the
brightness levels is calculated based on the PWM resolution.
The calculation of the table using the CIE 1931 algorithm is enabled by
default when you do not define the 'brightness-levels' propriety in your
device tree.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The num-interpolated-steps property specifies the number of
interpolated steps between each value of brightness-level table. This is
useful for high resolution PWMs to not have to list out every possible
value in the brightness-level array.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Setting num-interpolated-steps in the dts will allow you to have linear
interpolation between values of brightness-levels. This way a high
resolution pwm duty cycle can be used without having to list out every
possible value in the dts. This system also allows for gamma corrected
values.
The most simple example is interpolate between two brightness values a
number of steps, this can be done setting the following in the dts:
brightness-levels = <0 65535>;
num-interpolated-steps = <1024>;
default-brightness-level = <512>;
This will create a brightness-level table with the following values:
<0 63 126 189 252 315 378 441 ... 64260 64323 64386 64449 65535>
Another use case can be describe a gamma corrected curve, as we have
better sensitivity at low luminance than high luminance we probably
want have smaller steps for low brightness levels values and bigger
steps for high brightness levels values. This can be achieved with
the following in the dts:
brightness-levels = <0 4096 65535>;
num-interpolated-steps = <1024>;
default-brightness-level = <512>;
This will create a brightness-levels table with the following values:
<0 4 8 12 16 20 ... 4096 4156 4216 4276 ... 65535>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This change updates the device headers to the latest device version.
Where renaming affects the existing code, it's updated accordingly.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
The buffer object backing the user fence is reserved using the non-user
fence, i.e., as soon as the non-user fence is signaled, the user fence
buffer object can be moved or even destroyed.
Therefore, emit the user fence first.
Both fences have the same cache invalidation behavior, so this should
have no user-visible effect.
Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
In the quest to remove all stack VLA usage from the kernel[1], this moves
the "$#" replacement from being an argument to being inside the function,
which avoids generating VLAs.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change the tasklets parameter type to fix W=1 warnings when building
with gcc 8 like below:
drivers/s390/block/dasd.c: In function 'dasd_alloc_device':
drivers/s390/block/dasd.c:129:8: warning: cast between incompatible function types
from 'void (*)(struct dasd_device *)' to 'void (*)(long unsigned int)' [-Wcast-function-type]
(void (*)(unsigned long)) dasd_device_tasklet,
^
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Acked-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for format 3 function measurement blocks.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
NetworkManager likes to manage linklocal prefix routes and does so with
the NLM_F_APPEND flag, breaking attempts to simplify the IPv6 route
code and by extension enable multipath routes with device only nexthops.
Revert f34436a430 and these followup patches:
6eba08c362 ("ipv6: Only emit append events for appended routes").
ce45bded64 ("mlxsw: spectrum_router: Align with new route replace logic")
53b562df8c ("mlxsw: spectrum_router: Allow appending to dev-only routes")
Update the fib_tests cases to reflect the old behavior.
Fixes: f34436a430 ("net/ipv6: Simplify route replace and appending into multipath route")
Signed-off-by: David Ahern <dsahern@gmail.com>
Add support for DA9063L, which is a reduced variant of the DA9063
with less regulators and without RTC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move the LDOs present only on DA9063 at the end of the list, so that
the DA9063L can simply indicate less LDOs and still share the list of
regulators with DA9063.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The DA9063L does not contain RTC block, unlike the full DA9063.
Split the RTC block into separate mfd cell and register it only
on DA9063.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The DA9063L does not have an RTC. Add custom IRQ map for DA9063L to
ignore the Alarm and Tick IRQs from the PMIC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The DA9063L does not have an RTC. Add custom regmap for DA9063L to
prevent access into that register block.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add type for DA9063L, which is a reduced variant of the DA9063
without RTC block and with less regulators.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
