The yt921x_port_is_internal/external() macros hardcoded the port layout:
they treat ports 8 and 9 as external on every chip and count the dummy
ports as internal.
Identify the actual port capabilities using chip info and track
configuration of external ports (although only SerDes is supported now).
This is a hardening and cleanup step ahead of the SerDes PCS support, no
behavior changes intended.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260923021945.2203368-4-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace external_mask with xmii_mask and serdes_mask, and advertise the
interface modes it actually supports.
Also move struct yt921x_info into chip.h for future use.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260923021945.2203368-3-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove YT921X_PORT_MASK_* macros since they are only thin wrappers
around BIT() and GENMASK() and are not used in other places (plain BIT()
and GENMASK() are used there). No functional change.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260923021945.2203368-2-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nathan Whitehorn says:
====================
net: macb: 1000BASE-X on internal PCS
This series adds support for 1000BASE-X autonegotiation to the Cadence macb
driver when using the MAC-internal PCS. The existing driver code is oriented
toward the PCS being used with an on-board SGMII PHY, so uses Cisco
SGMII-style autonegotiation exclusively and does not anticipate e.g. link
state changes arising from fiber attach/detach events since the SGMII endpoint
is permanently attached in such cases. The first patch changes the driver
to monitor the PCS's link by polling, following the approach used currently
by this driver for fixed links when the PCS is enabled since the driver
does not currently monitor PCS link state otherwise and this had not come up
with permanently-attached SGMII PHYs that report link state out of band.
The second extends the existing SGMII autonegotiation code to also support
1000BASE-X autonegotiation.
Tested on Microchip PolarFire SoC with a variety of SFPs (copper, fiber, GPON)
attached to the I/O Bank-5 PCS lines.
Thanks to Charles Perry, Andrew Lunn, Paolo Abeni, Théo Lebrun, and
Jakub Kicinski for helpful suggestions and discussion on this patch series.
As a brief summary of that discussion, there are a few areas near this patch
that are existing non-idealities in the macb driver, in particular that it uses
polling to monitor link-state with the internal PCS and the driver does not
currently have support for using the link-state change interrupt. The
intention is to address this in a later patch that would remove polling from
both this case and the fixed-link one. Other discussion in earlier rounds
of the patches was related to handling some ZynqMP-specific code that is
related to specific SGMII-only hardware that is not relevant in the 1000BASE-X
case.
====================
Link: https://patch.msgid.link/20260922151429.23272-1-nwhitehorn@pa.msu.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current PCS code unconditionally uses SGMII autonegotiation, though
the hardware supports both SGMII and 1000BASE-X modes. Decouple the
choice of PCS enablement from use of the SGMII mode when running at
gigabit rates and announce to phylink that 1000BASE-X is a supported
operating mode. This enables direct attachment of the PCS to e.g. an
SFP.
The 1000BASE-X code in phylink also sometimes calls the autonegotiation
restart method, so add an implementation of autonegotiation restart and
make sure that pcs_config() signals to phylink when the AN advertisement
has changed.
Signed-off-by: Nathan Whitehorn <nwhitehorn@pa.msu.edu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260922151429.23272-3-nwhitehorn@pa.msu.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When used with an offboard transceiver (e.g. an SFP), link state needs
to be measured at the PCS rather than an onboard PHY. Poll the link
state when the PCS is active to allow the kernel to detect link state
changes in this case.
Signed-off-by: Nathan Whitehorn <nwhitehorn@pa.msu.edu>
Reviewed-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://patch.msgid.link/20260922151429.23272-2-nwhitehorn@pa.msu.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
idt82p33_ptp_clock_unregister_all() cancels each channel's adjtime work
before unregistering its PTP clock. An adjustment callback already in
progress can schedule that work after cancellation returns. Device
removal then frees the channel while its delayed work remains queued,
causing a use-after-free.
Mark the device as stopping under its lock before draining work. Reject
new adjustment and EXTS requests, clear the EXTS polling mask, and
synchronously drain the EXTS and channel adjustment work before the
device storage is released.
With an i2c-stub device and kprobe-controlled callback timing, three
runs of the unmodified driver reported KASAN use-after-free after
unbind. Three runs with this change completed without a kernel
diagnostic. No physical IDT82P33 device was tested.
Cc: stable+noautosel@kernel.org # untested fix to a driver init path race
Signed-off-by: Yibo Tan <lhfff@tju.edu.cn>
Link: https://patch.msgid.link/20260922113601.855416-1-lhfff@tju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Niklas Söderlund says:
====================
ravb: Add gPTP support for Gen4
This series is the second part cleaning up how PTP timer support is
implemented on R-Car Gen4. Currently there is partial support for it
in some of the Ethernet devices that can use it, but not all.
On Gen2 and Gen3 each RAVB instance have it's own private PTP clock as
part of the RAVB register space. For this reason the PTP functionally
was implemented directly in the RAVB driver. For Gen4 however there is
a system-wide PTP clock shared by all RAVB instances, and on some Gen4
platforms with other Ethernet devices.
The RAVB Gen4 driver currently advertise PTP support to user-space, but
the support is in fact completely broken. It tries to use RAVB private
PTP clock, which do not exist on Gen4.
Further more the PTP clock behaved slightly different on Gen2 and Gen3.
These differences have been handled by adding platform specific flags
inside the driver.
The usage of these flags have grown organically and been extended all
over the driver as it gained new features. Adding a new third set of
flags for Gen4 would be messy and add to the confusion.
Therefore patches 1/10 thru 8/10 refactors the usage of the PTP flags
into optional callbacks and untangles the usage. This allows adding Gen4
support easy as it can just implement it's own set of Gen4 specific
callbacks without altering the driver logic.
Patch 9/10 is a small DT binding addition adding an optional phandle to
link a RAVB device to the external PTP clock. Ideally this property
should be mandatory, but for backward comp ability is is made optional.
If the phandle is not set, or the PTP clock not enabled, the RAVB driver
will continue to faction as before, but no longer advertise PTP support
to user space.
Finally patch 10/10 adds the Gen4 specific PTP callbacks which allows
the driver to use the external PTP clock.
For part one of this work see [1]. The two series are independent of
each other but both are needed before a third series liking the RAVB to
the PTP clock in the platforms device tree. I will hold posting the
third series until all dependencies are merged. For this reason there
is no user of the new renesas,gptp device tree property added in this
series.
The work is tested on both Gen3 and Gen4 R-Car devices (with [1] and
appropriate DTS). I do however not have access to any Gen2 device where
the RAVB IP is wired to a MAC, so the small rework of the flags for Gen2
to callbacks have only been compiled tested. If anybody have a RZ device
where RAVB is wired and uses the Gen2 method of starting/stopping the
PTP timer together with the DMAC please test this.
[1] https://lore.kernel.org/20260803095232.3527111-1-niklas.soderlund+renesas@ragnatech.se/
====================
Link: https://patch.msgid.link/20260921175037.4084310-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While driver advertises gPTP support on Gen4 platforms it is in fact
completely broken. On R-Car Gen4 devices the RAVB module have no
internal gPTP clock as generations before it. Instead it utilizes a
system-wide gPTP clock.
This change utilizes the refactoring of the RAVB gPTP code to add
support for a system-wide clock and stops the Gen4 devices trying to use
the non-existing internal gPTP clock.
To remain backward compatible the ptp-timer property is optional.If not
present, or not enabled, the RAVB driver will no longer advertise gPTP
support to user-space.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergey Shtylyov <sergei.shtylyov@gmail.com>
Link: https://patch.msgid.link/20260921175037.4084310-11-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RAVB module on Gen4 have no gPTP clock as part of the RAVB module
itself, instead it relies on an external system wide gPTP clock. The
gPTP clock is shared with RTSN on V4H and RSWITCH on S4.
Add an optional phandle so that the RAVB driver can find and use the
gPTP clock. Ideally this should have been a mandatory property but for
backward compatible it is optional. The RAVB module is capable of
functioning without it, but can in such cases not provided PTP
functionality.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergey Shtylyov <sergei.shtylyov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260921175037.4084310-10-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Prepare for adding Gen4 support which have an optional external gPTP
clock. Add a callback to get the clock index and use it to determine if
the device shall report gPTP support.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergey Shtylyov <sergei.shtylyov@gmail.com>
Link: https://patch.msgid.link/20260921175037.4084310-9-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Different generations of the RAVB IP have different needs when it probes
the gPTP timer clock. Add a callback in the PTP information to allow
each generation to probe its own way.
With this the last gPTP specific flag (gptp_ref_clk) can be removed.
However the primary motivation for the change is to prepare for Gen4
support, which compared to other generations with gPTP support does not
have the clock as part of the IP itself.
Gen4 will not need to compute GTI value as it have nowhere to write it,
as the gPTP clock is external. For this reason move the computation of
it into the newly gPTP probe specific callbacks for the RAVB IP's that
support it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergey Shtylyov <sergei.shtylyov@gmail.com>
Link: https://patch.msgid.link/20260921175037.4084310-8-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Prepare for adding Gen4 support which will add a third and new way to
interact with the gPTP clock by replacing the flags for Gen2 behavior
(info->gptp) and Gen3 behavior (info->ccc_gac) with callbacks.
This will make adding Gen4 support cleaner as the code will not have "if
else if else" sprinkled all over to handle each generations special
cases.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergey Shtylyov <sergei.shtylyov@gmail.com>
Link: https://patch.msgid.link/20260921175037.4084310-7-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no need to explicitly pass the struct platform_device pointer
to ravb_ptp_init(), it can retrieve it directly from the private data
structure.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergey Shtylyov <sergei.shtylyov@gmail.com>
Link: https://patch.msgid.link/20260921175037.4084310-5-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For devices that do not support the gPTP clock in config mode the
somewhat oddly named flag gptp is set, compared to devices that do
support the gPTP clock in config and operation mode where the flag
ccc_gac is set instead. The two flags are mutually exclusive.
For the gptp-flag devices (Gen2) the clock is tied to the AVB-DMAC, when
it is stopped so is the gPTP clock. For ccc_gac-flag devices (Gen3) the
gPTP clock is available whenever the ndev is open.
Prepare to add Gen4 support which will add a third way by cleaning the
Gen2 and Gen3 cases up a bit.
Fold the gptp-flag start and stop calls into ravb_dmac_init() and
ravb_stop_dma(), which start and stop the AVB-DMAC. There are no
functional change as all call sites to the construct:
if (info->gptp)
ravb_ptp_init(ndev, priv->pdev);
are always just after a call to into ravb_dmac_init() and all call sites
to the construct:
if (info->gptp)
ravb_ptp_stop(ndev);
are always directly followed by a call to ravb_stop_dma().
There are two special cases where the calling construct covers both the
gptp-flag and info->ccc_gac devices, one for start and one for stop. The
condition that it is preceded by a call to ravb_dmac_init(), or followed
by a call to ravb_stop_dma() are however true for them too. Reworked the
two special cases to drop the check of info->gptp.
The end result is that the gPTP clock will be started or stopped for the
gptp-flag devices in tandem with the AVB-DMAC, while the info->ccc_gac
devices will be controlled, as before, when the ndev is opened or
closed.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergey Shtylyov <sergei.shtylyov@gmail.com>
Link: https://patch.msgid.link/20260921175037.4084310-4-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit f384ab481c ("net: ravb: Split GTI computation and set
operations") broke apart the operations of computing the timer interval
and programming of it. However it kept the programming of the interval
in the RAVB main logic.
Having split the two apart this can be improved further by moving the
programming to the gPTP initialization function, as the first action of
the gPTP init function is to wait for the timer interval programming to
be acknowledge by the hardware.
As an added bonus the interaction with the gPTP registers for the
programming can then also be done while holding the gPTP registers lock.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergey Shtylyov <sergei.shtylyov@gmail.com>
Link: https://patch.msgid.link/20260921175037.4084310-3-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit a6a85ba36f ("net: ravb: Move PTP initialization in the
driver's ndo_open API for ccc_gac platorms") the gPTP clock (if
supported) is stopped and started by opening and closing the ndev.
This makes the special case to stop and start it when resuming from WoL
redundant. As the ndev will always be closed and re-opened when
resuming the system.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergey Shtylyov <sergei.shtylyov@gmail.com>
Link: https://patch.msgid.link/20260921175037.4084310-2-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet says:
====================
net: ethtool: make netdev_rss_key_fill() spread flows over all queues
netdev_rss_key_fill() hands drivers a uniformly random key. Because the
Toeplitz hash is linear over GF(2), a random key is singular for a given
header field and queue count with probability 1/2: flows differing only
in the low order bits of that field (such as a burst of consecutive
ephemeral ports) then cannot reach all RX queues. On one affected 16-queue
host, only 4 queues received traffic until the key was replaced.
Patch 1 synchronizes proc_do_rss_key() with netdev_rss_key_fill() using an
smp_wmb()/smp_rmb() pair and a boolean flag so readers of
/proc/sys/net/core/netdev_rss_key print zero bytes until the key is fully
populated.
Patch 2 keeps the key random but constrains 1008 of its 2048 bits so that,
at every 16-bit aligned position and for every power-of-two queue count up
to 256, consecutive values of a field ending there visit every queue once.
Applying the fixup on the 16-bit grid covers standard 2-tuple/4-tuple
hashes as well as encapsulated or bitmap-selected layouts (such as PSP
inner TCP ports at byte 78) without enumerating them in the core. The
fixup is a bijection onto the set of valid keys, and redraws in the ~1 in
5 case where two 32-bit windows a multiple of 8 bits apart alias.
Patch 3 adds RSS key, indirection table, and flow-hash reporting to
netdevsim so the selftest can exercise both the host key and ethtool
netlink RSS reporting in a virtual machine without hardware.
Patch 4 adds a selftest under tools/testing/selftests/drivers/net/rss_key.py
checking /proc/sys/net/core/netdev_rss_key and the live RSS key,
indirection table, and flow-hash layouts reported by a device via ethtool
netlink.
====================
Link: https://patch.msgid.link/20260922163458.3900996-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a selftest under tools/testing/selftests/drivers/net/rss_key.py
checking both the host RSS key (/proc/sys/net/core/netdev_rss_key) and
the RSS key, indirection table, and flow-hash layouts reported by a
device over ethtool netlink.
When invoked without NETIF, NetDrvEnv creates a 4-queue netdevsim device,
which calls netdev_rss_key_fill() and allows exercising both the host key
and the netlink RSS reporting path in a virtual machine without special
hardware. When invoked with NETIF, it checks the key and indirection
table of that interface.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260922163458.3900996-5-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Initialize a per-device RSS key in nsim_ethtool_init() using
netdev_rss_key_fill() and wire up get_rxfh_key_size, get_rxfh_indir_size,
get_rxfh, and get_rxfh_fields on nsim_ethtool_ops.
This allows RSS selftests under tools/testing/selftests/drivers/net/ to
exercise both /proc/sys/net/core/netdev_rss_key and ethtool netlink RSS
reporting against netdevsim without requiring physical hardware.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260922163458.3900996-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
netdev_rss_key_fill() returns a key made of uniformly random bytes. That
is not enough, because the Toeplitz hash is linear over GF(2).
Walking the hash input MSB first, each set bit contributes a 32-bit
sliding window of the key, and hardware indexes the indirection table with
the low order bits of the result. Only the tail of each window therefore
reaches the queue index:
v(i) = key bits [i + 32 - q .. i + 31]
with q = log2(number of RX queues). Consecutive input bits give windows
overlapping in q - 1 positions, so the q vectors belonging to the q lowest
bits of a header field form a Toeplitz matrix built from 2 * q - 1 key
bits, rather than q * q independent ones. Over GF(2) a random Toeplitz
matrix is singular with probability exactly 1/2, whatever its size.
When it is singular, flows differing only in the low order bits of that
field cannot reach all the queues. This is not theoretical: a burst of
connections draws ephemeral ports from a narrow range, and on one affected
host only 4 of the 16 RX queues received any traffic at all, until its key
was replaced.
Keep drawing the key at random, since it is a secret that stops a remote
attacker from steering flows onto a single queue, but force the handful of
bits that decide this. Writing d[t] for key bit (lsb + 31 - t), where lsb
is the position of the least significant bit of a field in the hash input,
the matrices of all the q values up to 8 are non singular if and only if
d[2 * i] = 1 ^ d[i] ^ d[i + 1] ^ ... ^ d[2 * i - 1]
The odd positions stay free, so this is a one pass fixup rather than a
search. It is in fact a bijection from those free positions onto the set
of the values having the property, so the key stays uniformly distributed
over that set and the whole cost is 8 bits of entropy per position.
Searching for such a key by rejection would not have been an option: a
freshly drawn one has the property everywhere with probability 2^-1008.
Apply this at every 16-bit aligned position of the key, rather than at the
offsets of the 2-tuple and 4-tuple layouts only. The core does not get to
know what a given NIC hashes. Hardware may select the bytes it feeds to
Toeplitz out of a header window with a bitmap, and hash an encapsulated
header: for PSP over UDP over IPv6 it can pick the outer addresses and the
inner TCP ports, which sit 78 bytes into the frame and read key bits well
past the 40 bytes an IPv6 4-tuple needs. Hashed fields are 16 bits wide at
the smallest and are not expected to straddle that grid, so covering the
grid covers the layouts that were never written down, at no cost in code.
This spends 8 bits of entropy per position, 1008 bits out of the 2048 bits
of netdev_rss_key, leaving 1040 bits. 8 is also the largest usable bound,
as each q constrains 2 * q - 1 bits and anything larger would make the
ranges of two adjacent positions overlap.
What the fixup leaves behind is visible structure: 8 of every 16 bits are
derived from the 8 others, so a 16-bit aligned word of the key takes only
2^8 values and about 27 of the 128 words of netdev_rss_key duplicate
another one. That much is forced rather than an artefact of this
implementation, 1040 bits spread over 128 words being a little over 8 bits
each, but it has one consequence worth removing. Two 32-bit windows a
whole number of words apart now collide with probability 2^-16 instead of
2^-32, and two input bits reading the same window are indistinguishable to
the hash, since flipping both of them leaves it unchanged. Over 500 keys,
23% of them had such a pair, where a uniformly random key has one with
probability 2^-11.
So draw another key when that happens. Four out of five pass. Which
distances to look at follows from where the structure is: covering the
multiples of 16 leaves 1.2e-3 expected colliding pairs per key, still 2.6
times the 4.6e-4 of a plain random key, and almost all of that excess sits
at a distance of 8 modulo 16. Covering every multiple of 8 brings the total
down to 4.2e-4, below what a plain random key gives over all distances, and
within a few percent of the 4.0e-4 it gives over the distances that are
left.
Two windows a multiple of 8 bits apart are two windows at the same offset
modulo 8, so this is a handful of pairwise sweeps rather than one pass over
the key per distance. DO_ONCE() runs the generator under a spinlock with
hard IRQs disabled, so keep the windows of a class in an array rather than
recomputing both sides of every pair: 116 us instead of 254 us for the
worst case, a 2048-bit key with no collision anywhere, at a cost of 512
bytes of stack.
The shared key is fixed up once and every driver prefix inherits both
properties. Move netdev_rss_key and netdev_rss_key_fill() from
net/ethtool/ioctl.c to net/ethtool/common.c, and move the netdev_rss_key
declaration out of include/linux/netdevice.h into net/core/dev.h.
Checked against an independent Toeplitz implementation: for every 16-bit
aligned position and every q in 1..8, an aligned block of 2^q consecutive
values of a field ending there lands on the 2^q queues exactly once each.
Over 20 random keys that is 20160 checks, which 50.1% of plain random keys
fail and none of the generated keys do, for an average of 502 rewritten
bits out of 2048.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260922163458.3900996-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
proc_do_rss_key() reads netdev_rss_key[] without synchronization, so a
concurrent reader of /proc/sys/net/core/netdev_rss_key can observe a
partially populated key while netdev_rss_key_fill() is initializing it.
Publish a boolean flag after an smp_wmb() once netdev_rss_key_fill() has
populated netdev_rss_key[], and pair it with an smp_rmb() in
proc_do_rss_key(), printing zero bytes until the flag is set.
Fixes: 960fb622f8 ("net: provide a per host RSS key generic infrastructure")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260922163458.3900996-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Every week in this release is record-setting for number of posted
patches. It doesn't seem like we're creating any regressions with
all these fixes, 3 Fixes tags here point to 7.2 commits but none
are true regression fixes. We're trying to keep the count down,
nonetheless.
Previous releases - regressions:
- net: don't require the hwtstamp NDOs when a PHY provides timestamping
- ipv6: fix dst leak for uncached routes
- vrf: stop corrupting skb->csum when capturing CHECKSUM_COMPLETE
packets
Previous releases - always broken:
- packet: use ubuf_info completion for TX_RING packets
- arp: terminate device name before lookup
- ipv6: do not let ipv6_find_hdr() return an offset past the packet end
- udp: remove a disconnected socket from the 4-tuple hash table
- sctp: discard the rest of the packet on a stale-cookie error
- eth: mlx5: Bridge, fix remaining switchdev ownership gaps on merged
eswitch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAmq1bCQACgkQMUZtbf5S
IrsgCBAAiHOxV3pR0pNw+K/dO5maYhuUV4w+Xcd6CbjRnxzYtImVC1q2ieez5dEe
JrQrVK76t2wuEgGSyiWcckIufPL8xYg5nYaOUbkYMC2QRtDaqhCo+u2jXu26/Lr8
O3sI2cj86XDZN+xKTvmLld1zIRyD6MhYxWz+gIicArdBqTsr5JsWkwhJE7SH013a
iVGu0sIxTgCNu/AusD6SdtwFte26dqvadelI8yuDhBR6rM9pi4EWXChleg7ohCsu
DoZTlaEjEiFavat+6ni99oz8MAT0WVBX0IzTqZa6TCnbCw4qUEbqN8G+CNgC/VPe
Sq5FRoo6vJjlFviwgWPbpje2FoOYtk6CX1eTavx8gZ4pPMTzGkT62crS+ETwLO5H
mRbE+ZjG8UDTUKpIY5P/IQYdznHSc9Ny/pHNlZhFmDdntJOp1lnegx5CmZkyuZxC
Qc0hoFxKdjUrpQ1n0ygT3/P6MT9vXMwbGP52VLIxaB1oaYCKFV71NOp0ET5fCnYb
CBK8cdN0kcaSLrpi3MnPamyQoNZfH78BiuKsLDu/TWg3i2HGmFTlp0/LJ0nkQcCU
4KlCmiJNOkHjbQKHNtYMUOZQcZu5witEv33kb7gr581b0RR+n0lZTaXcnRIyXYdb
ORqIa1Khg5mW3DLaIc9IrzEGGAW5zXUHc5OX7t8J2rVRQWhBEh4=
=YiiK
-----END PGP SIGNATURE-----
Merge tag 'net-7.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from Bluetooth, NFC and Netfilter.
Every week in this release is record-setting for number of posted
patches. It doesn't seem like we're creating any regressions with all
these fixes, three 'Fixes' tags here point to 7.2 commits but none are
true regression fixes. We're trying to keep the count down,
nonetheless.
Previous releases - regressions:
- net: don't require the hwtstamp NDOs when a PHY provides
timestamping
- ipv6: fix dst leak for uncached routes
- vrf: stop corrupting skb->csum when capturing CHECKSUM_COMPLETE
packets
Previous releases - always broken:
- packet: use ubuf_info completion for TX_RING packets
- arp: terminate device name before lookup
- ipv6: do not let ipv6_find_hdr() return an offset past the packet
end
- udp: remove a disconnected socket from the 4-tuple hash table
- sctp: discard the rest of the packet on a stale-cookie error
- eth: mlx5: Bridge, fix remaining switchdev ownership gaps on merged
eswitch"
[ And lots of other random network driver fixes ]
* tag 'net-7.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (189 commits)
tcp: prevent collapsing skbs across boundary in rtx queue
vlan: ensure sufficient headroom in vlan_dev_hard_header()
net/sched: sch_teql: fix shadowed err in __teql_resolve()
bridge: check llc_mac_hdr_init() return value in br_send_bpdu()
llc: fix skb UAF and leaks on llc_mac_hdr_init() failure
llc: reserve device headroom for allocated frames
gve: DQO: reject TSO packets with an out of range MSS
gve: fix TX drop when GSO MSS is too small for hw
gve: DQO: fix header length used by gve_can_send_tso() for UDP GSO
net: flush skb_defer_nodes in dev_cpu_dead()
net: ethernet: stmmac: dwmac-rk: fix bulk clock leak when the PHY clock fails
af_packet: fix integer overflow in prb_calc_retire_blk_tmo()
tipc: Fix a data race on mon->peer_cnt in mon_timeout()
net: phy: intel-xway: workaround 100BASE-TX Link-Up issue
net/smc: fix UAF on lgr list traversal in smcr_port_err()
net/rds: size a connection's path set by the transport it ends up with
nfp: hold IPsec RX state under the XArray lock
net: ena: fix MMIO read buffer leak on probe failure
net: ena: fix PHC cleanup on probe failure
net/sched: act_ct: fix helper UAF due to extensions realloc
...
tcp_write_collapse_fence() sets TCP_SKB_CB(skb)->eor = 1 on
tcp_write_queue_tail(sk) to prevent skbs queued after a switch to
device encryption from being collapsed into earlier skbs.
The fence is a no-op if all earlier data has already been transmitted
when the switch happens: sk->sk_write_queue is empty. The not yet
acknowledged earlier skbs wait in sk->tcp_rtx_queue with eor 0.
On a subsequent retransmit or SACK shift, tcp_retrans_try_collapse() or
tcp_shift_skb_data() can then merge an skb queued after the switch into
one queued before it.
Both users of the fence are affected:
- psp: devices only encrypt skbs with skb->decrypted set. The merged skb
keeps decrypted = 0 from the earlier skb, so merged data sent after
psp_sock_assoc_set_tx() is retransmitted in cleartext.
- tls device offload: the merged skb straddles the start marker set in
tls_set_device_offload(). The software fallback (fill_sg_in() returns
-EINVAL) and the mlx5, nfp and funeth drivers cannot handle such an
skb and drop it. Every retransmit rebuilds the same skb, so the
connection stalls.
Fix this in two places, for defense in depth:
1. Fall back to tcp_rtx_queue_tail(sk) in tcp_write_collapse_fence()
when tcp_write_queue_tail(sk) is NULL.
2. Check !skb_cmp_decrypted(to, from) in tcp_skb_can_collapse(), as
tcp_skb_can_collapse_rx() does on receive. skb_shift(), which both
collapse paths call, already has a DEBUG_NET_WARN_ON_ONCE() for this
condition.
Fixes: e8f6979981 ("net/tls: Add generic NIC offload infrastructure")
Cc: stable@vger.kernel.org
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Daniel Zahka <daniel.zahka@gmail.com>
Link: https://patch.msgid.link/20260924154427.953800-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet says:
====================
vlan: ensure sufficient headroom in vlan_dev_hard_header()
Callers that only reserve ETH_HLEN or less, or skbs allocated before
dynamic device/headroom changes (such as toggling VLAN_FLAG_REORDER_HDR
or bonding/team switching slaves), can reach vlan_dev_hard_header() with
insufficient headroom and trigger skb_under_panic().
When vlan_dev_hard_header() returns -ENOMEM upon skb_cow_head() failure,
a few callers of dev_hard_header() / llc_mac_hdr_init() had pre-existing
error-handling bugs:
====================
Link: https://patch.msgid.link/20260924082951.1599377-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Callers that only reserve ETH_HLEN or less (such as llc_alloc_frame()),
or skbs allocated before dynamic device/headroom changes (e.g. toggling
VLAN_FLAG_REORDER_HDR or bonding/team switching slaves), can reach
vlan_dev_hard_header() with insufficient headroom and trigger
skb_under_panic().
Use skb_cow_head() in vlan_dev_hard_header() when VLAN_FLAG_REORDER_HDR
is not set to ensure sufficient headroom for the VLAN header(s) and the
underlying device hard header.
Use READ_ONCE() to read dev->hard_header_len and dev->needed_headroom as
they can be updated concurrently under RTNL (e.g. in
vlan_transfer_features()) while vlan_dev_hard_header() runs locklessly on
the transmit path. Also avoid LL_RESERVED_SPACE(dev) here so that the
extra HH_DATA_MOD alignment padding does not trigger unnecessary
pskb_expand_head() reallocations on inner stacked VLAN devices after the
outer VLAN header has been pushed.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Zixuan Chai <petalzu987@gmail.com>
Closes: https://lore.kernel.org/netdev/cover.1789987105.git.petalzu987@gmail.com/
Link: https://lore.kernel.org/netdev/179022851638.2160803.1808206741379444999@kernel.org/
Cc: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260924082951.1599377-5-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
__teql_resolve() declares an inner 'int err;' inside the
'if (neigh_event_send(n, skb_res) == 0)' block, shadowing the outer
'int err = 0;'. As a result, a negative return from dev_hard_header()
is written to the inner variable and __teql_resolve() still returns 0.
Remove the shadowed variable and set the outer err to -EINVAL when
dev_hard_header() returns a negative error.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Closes: https://lore.kernel.org/netdev/179022851638.2160803.1808206741379444999@kernel.org/
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260924082951.1599377-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In llc_conn_ac_resend_i_xxx_x_set_0_or_send_rr(), if llc_mac_hdr_init()
fails, kfree_skb(skb) is called instead of kfree_skb(nskb). This leaks
the newly allocated nskb, reads from the freed skb via LLC_I_GET_NR(pdu),
and double-frees skb when llc_conn_state_process() drops its reference.
In llc_sap_action_send_xid_r() and llc_sap_action_send_test_r(), nskb is
leaked if llc_mac_hdr_init() returns an error.
Free nskb in all three error paths.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Closes: https://lore.kernel.org/netdev/179022851638.2160803.1808206741379444999@kernel.org/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260924082951.1599377-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
llc_alloc_frame() reserves link-layer headroom using the device type.
This is insufficient for stacked Ethernet devices such as VLAN devices,
where vlan_dev_hard_header() pushes a VLAN header before the lower
device's Ethernet header. An LLC response on such a device can
therefore underflow skb headroom in eth_header().
Use LL_RESERVED_SPACE() to account for the device's actual required
headroom while preserving the existing LLC device-type check.
Fixes: bf9ae5386b ("llc: use dev_hard_header")
Cc: stable@vger.kernel.org
Reported-by: VEGA <vega@nebusec.ai>
Signed-off-by: Zixuan Chai <petalzu987@gmail.com>
Signed-off-by: Ren Wei <weir@nebusec.ai>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260924012613.2533934-1-weir@nebusec.ai
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet says:
====================
gve: DQO: fix handling of out of range TSO MSS
The DQO TX path assumes that the MSS of a TSO packet is within the
range supported by the device, [88, 9728].
This holds for locally generated traffic, but not for packets coming
from a tap or from a packet socket: virtio_net_hdr_to_skb() takes
gso_size from user space and only enforces a minimum, layer 2
forwarding does not check the MTU of GSO packets, and
gso_features_check() bounds skb->len and gso_segs but never gso_size.
Patch 1, from Eddie Phillips, deals with the lower bound. It moves the
existing test out of gve_prep_tso() into gve_features_check_dqo(), so
that these packets are segmented in software instead of being dropped.
Patch 2 deals with the upper bound, which is currently not checked at
all. gve_tx_fill_tso_ctx_desc() stores gso_size into a 14 bits wide
field, so that an MSS of 16384 silently becomes zero. Falling back to
software segmentation is not an option here, because skb_segment()
splits at gso_size regardless of the MTU, and would only replace an
invalid TSO packet by non TSO packets larger than the 9728 bytes the
device supports. These packets are dropped instead.
As noted in patch 2, oversized non TSO packets can still reach the
device whenever the stack segments in software. This is not specific
to gve and is better fixed in the core, so a patch for
__is_skb_forwardable() will be sent separately for net-next.
====================
Link: https://patch.msgid.link/20260924004252.1196328-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
gve_prep_tso() notes that the device requires the MSS to be <= 9728,
but does not enforce it, assuming the 9K MTU enforced by the hypervisor
and the 64KB limit on TSO sizes are enough.
This does not hold for packets that were not generated locally.
A guest behind a tap, or any packet socket user, can provide an
arbitrary gso_size in virtio_net_hdr. Layer 2 forwarding does not check
the MTU for GSO packets (is_skb_forwardable()), and gso_features_check()
only bounds skb->len and gso_segs, never gso_size.
Such a packet reaches gve_tx_fill_tso_ctx_desc(), which puts gso_size
into the mss field of the TSO context descriptor. This field is 14 bits
wide, so a gso_size of 16384 is silently turned into an MSS of zero.
Drop these packets from gve_prep_tso(), and make sure that
gve_features_check_dqo() leaves their GSO bits alone: skb_segment()
splits at gso_size regardless of the MTU, so falling back to software
segmentation would give the device non TSO packets bigger than the
9728 bytes it supports.
Note that the device can still be given oversized non TSO packets when
the stack segments in software for other reasons, for instance after
TSO has been disabled with ethtool. This is a generic issue, because
the MTU check is skipped for GSO packets in the forwarding path, and
is addressed separately.
Fixes: a57e5de476 ("gve: DQO: Add TX path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20260924004252.1196328-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The device has a strict requirement that the minimum MSS
(gso_size) for TSO/GSO packets must be at least 88 bytes. If a packet
below this threshold is pushed to the hardware, it can cause
hardware to silently drop the packet, leading to increased latency
and retransmissions.
Currently, this is validated too late in the transmit pipeline
(gve_prep_tso), leading to silent drops.
Fix this by moving the validation into the .ndo_features_check
callback (gve_features_check_dqo). If we detect a GSO packet with
a gso_size smaller than GVE_TX_MIN_TSO_MSS_DQO, we clear the GSO
feature flags for this packet.
Fixes: a57e5de476 ("gve: DQO: Add TX path")
Signed-off-by: Eddie Phillips <eddiephillips@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20260924004252.1196328-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iIYEABYKAC4WIQSVyBthFV4iTW/VU1/l49DojIL20gUCarVI0xAcbWljQGRpZ2lr
b2QubmV0AAoJEOXj0OiMgvbSEVgA+gNbC9CVCbCo0oufZbVpQwlwtuuEKEVpvxZx
q7oFYKCsAP9svCujGCXRHOmWhAAwe+wpXNb43l8coFn+pCfA8x3fCw==
=NOli
-----END PGP SIGNATURE-----
Merge tag 'landlock-7.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mic/linux
Pull Landlock fixes from Mickaël Salaün:
"This mainly fixes the Landlock tracepoint support merged this cycle so
that denial and rule events report the intended policy context,
whether through tracefs or BTF-visible callbacks.
The size of this all is mainly from propagating the corrected contract
through event definitions and producers, adding new tests for the
reported context, and updating the documentation.
Also improve annotation and fix a GCC 16 build warning"
* tag 'landlock-7.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mic/linux:
landlock: Widen ruleset versions to 64 bits
landlock: Add counted_by in landlock_domain
landlock: Fix tracepoint contract documentation
selftests/landlock: Test network denial context
selftests/landlock: Test filesystem denial blockers
landlock: Report the effective signal number
landlock: Report the actual ptrace tracer
landlock: Fix network denial trace context
landlock: Fix rule tracepoint context
landlock: Fix filesystem denial blocker reporting
landlock: Fix tracepoint fixed-width type names
landlock: Work around gcc-16 -Wuninitialized warning
gve_can_send_tso() computes how many buffers each segment of a GSO
packet would span, and for this it needs the length of the headers
that the device replicates in front of every segment.
It unconditionally uses skb_tcp_all_headers(), which reads the doff
field of the TCP header. SKB_GSO_UDP_L4 packets have no TCP header:
tcp_hdrlen() then reads one byte of the UDP payload, and header_len
can be anything in [0, 60] instead of the transport offset plus the
eight bytes of the UDP header that gve_prep_tso() programs into the
TSO context descriptor.
A wrong header length shifts all the segment boundaries computed in
the loop, so the number of buffers per segment can be over or under
estimated. In the first case, GSO is needlessly disabled for this
packet by gve_features_check_dqo() and the stack has to segment it.
In the second case, the driver hands the device a packet whose
segments span more than GVE_TX_MAX_DATA_DESCS buffers.
Use the UDP header length for SKB_GSO_UDP_L4 packets, matching what
gve_prep_tso() does.
Fixes: 014c607f86 ("gve: add support for UDP GSO for DQO format")
Closes: https://lore.kernel.org/netdev/CANn89i+MS4L60sFQ49=-f-mibeveUfcrpVkD5X+Qy6SOnEpd6w@mail.gmail.com/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ankit Garg <nktgrg@google.com>
Cc: Harshitha Ramamurthy <hramamurthy@google.com>
Cc: Joshua Washington <joshwash@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Ankit Garg <nktgrg@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20260923145942.731365-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a CPU goes offline, dev_cpu_dead() drains its softnet queues
(completion_queue, output_queue, poll_list, process_queue, and
input_pkt_queue), but leaves net_hotdata.skb_defer_nodes untouched.
If oldcpu goes offline while holding pending skbs in its
skb_defer_nodes lists (e.g. below the sysctl_skb_defer_max >> 1 IPI
threshold, or if the IPI races with CPU teardown), those skbs remain
stranded until oldcpu is brought back online. If any of these skbs
hold page_pool fragments, page_pool_destroy() will stall indefinitely
waiting for inflight pages to be returned when a netdev or driver is
torn down while oldcpu is offline.
Additionally, if smp_call_function_single_async() fails in
kick_defer_list_purge() because the target CPU went offline, reset
defer_ipi_scheduled to 0 so future IPI kicks are not blocked when the
CPU comes back online.
Also, if oldcpu was the last online CPU on its NUMA node, drain that
node's slot across all CPUs so no skbs deferred from that node remain
stranded on idle remote CPUs (or if the node itself is subsequently
offlined).
Finally, in skb_attempt_defer_free(), re-check cpu_online(cpu) and
whether the caller migrated CPUs after llist_add(), flushing the node
list if so, to close the preemption TOCTOU race against CPU/node
teardown.
Fixes: 68822bdf76 ("net: generalize skb freeing deferral to per-cpu lists")
Fixes: 5628f3fe3b ("net: add NUMA awareness to skb_attempt_defer_free()")
Closes: https://lore.kernel.org/netdev/20260916003430.3612956-1-kris.pan@intel.com/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Kris Pan <kris.pan@intel.com>
Link: https://patch.msgid.link/20260923130318.607255-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
gmac_clk_enable() enables the bulk clocks first and then the optional
PHY clock. If clk_prepare_enable() on the PHY clock fails, the function
returns without rolling back the bulk clocks, and bsp_priv->clk_enabled
stays false, so the later gmac_clk_enable(bsp_priv, false) becomes a
no-op and the bulk clock references are leaked.
Add the missing clk_bulk_disable_unprepare() on that failure path.
Fixes: ea449f7fa0 ("net: ethernet: stmmac: dwmac-rk: rework optional clock handling")
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@oss.qualcomm.com>
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Link: https://patch.msgid.link/20260923123713.3137146-1-coiaprant@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
prb_calc_retire_blk_tmo() computes in 32-bit int arithmetic:
mbits = (blk_size_in_bytes * 8) / (1024 * 1024);
If I'm reading the validation right, tp_block_size is user
controlled and packet_set_ring() only rejects values that are <= 0
as int or not page aligned, so a 256MiB block goes right through
(and alloc_one_pg_vec_page() even has a vzalloc fallback for it).
0x10000000 * 8 wraps to INT_MIN, and on a NIC reporting 1 Gbps
(div == 1) the function ends up returning -2047.
The condition is actually (8 * size) mod 2^32 >= 2^31 && div == 1,
so the trigger set is [256,512), [768,1024), [1280,1536) and
[1792,2048) MiB. Other sizes wrap to non-negative values and faster
links divide the unsigned value back below 2^31, which is why this
doesn't blow up for everyone.
What makes it fatal is what happens next in init_prb_bdqc():
p1->interval_ktime = ms_to_ktime(prb_calc_retire_blk_tmo(...));
hrtimer_start(&p1->retire_blk_timer, p1->interval_ktime,
HRTIMER_MODE_REL_SOFT);
A negative relative timeout expires immediately. The callback
unconditionally returns HRTIMER_RESTART, and hrtimer_forward() turns
the negative interval into hrtimer_resolution:
if (interval < hrtimer_resolution)
interval = hrtimer_resolution;
So the SOFT timer re-fires at the maximum rate forever, holding
sk_receive_queue.lock each pass. One CPU spins in softirq until the
socket is closed. Repeat with more rings and the machine is gone.
The overflow itself is ancient - it was introduced together with
TPACKET_V3 in f6fb8f100b ("af-packet: TPACKET_V3 flexible buffer
implementation."). Its effect prior to f7460d2989 ("net:
af_packet: Use hrtimer to do the retire operation", v6.18) was not
as clear-cut, though: the return value was stored into an unsigned
short retire_blk_tov, so a negative result was truncated, and a
0-jiffy delay loop could be programmed as well. Neither is nearly
as detrimental as the immediate maximum-rate spin the hrtimer
conversion turned it into.
(Unrelated to CVE-2019-20812 - that one was the ethtool failure path
returning 0, which now returns DEFAULT_PRB_RETIRE_TOV.)
Reproducer, needs CAP_NET_RAW (a --network host container has it by
default) and a 1 Gbps NIC (QEMU e1000 works):
int fd = socket(AF_PACKET, SOCK_RAW, htons(ETH_P_ALL));
bind(fd, ...);
int v = TPACKET_V3;
setsockopt(fd, SOL_PACKET, PACKET_VERSION, &v, sizeof(v));
struct tpacket_req3 req = {
.tp_block_size = 0x10000000,
.tp_block_nr = 1,
.tp_frame_size = 2048,
.tp_frame_nr = 0x10000000 / 2048,
.tp_retire_blk_tov = 0,
};
setsockopt(fd, SOL_PACKET, PACKET_RX_RING, &req, sizeof(req));
Compute in 64 bits instead. The operands are already bounded by the
existing validation, so nothing else changes. If you'd prefer a
different fix, just say so and I'll respin.
Fixes: f6fb8f100b ("af-packet: TPACKET_V3 flexible buffer implementation.")
Cc: stable@vger.kernel.org
Signed-off-by: Dairui Zhang <zhangdairui@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20260923050101.1510064-1-zhangdairui@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mon_timeout() evaluates dom_size(mon->peer_cnt) before it takes mon->lock,
while mon->peer_cnt is updated under that lock by tipc_mon_add_peer() and
tipc_mon_remove_peer(). The value can therefore be stale, and the decision
whether the local domain has to be recomputed can be based on an outdated
member count.
Read mon->peer_cnt inside the write_lock_bh(&mon->lock) protected region.
Fixes: 35c55c9877 ("tipc: add neighbor monitoring framework")
Signed-off-by: Ginger Li <ginger.jzllee@gmail.com>
Reviewed-by: Tung Nguyen <tung.quang.nguyen@est.tech>
Link: https://patch.msgid.link/20260922080909.21123-1-ginger.jzllee@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MaxLinear GSW12x/GSW14x Ethernet Switch Errata Sheet states:
"An issue has been sporadically observed after device power-on on the first
link-up attempt in 100BASE-TX mode resulting in either the link-up taking a
long time, or failing to link-up altogether...
Workaround:
After power-on, enable Cable Diagnostic Mode for all ports and disable
it..."
Implement the proposed workaround unconditionally in the Intel XWAY driver
(MaxLinear GSW1xx switches incorporate Intel XWAY PHYs) because the
diagnostic bits have the same meaning even in older integral PHYs such as
GPY111/PEF7071/PHY11G. So it's not clear how to distinguish the affected
newer integrated PHYs, but the workaround should not hurt the older PHYs.
Cc: stable@vger.kernel.org
Fixes: 22335939ec ("net: dsa: add driver for MaxLinear GSW1xx switch family")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260922075251.23386-1-alexander.sverdlin@siemens.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
smcr_port_err() traverses smc_lgr_list.list without holding
smc_lgr_list.lock, allowing a concurrent smc_lgr_terminate_sched()
to free an lgr while it is still being dereferenced.
Hold smc_lgr_list.lock across the traversal. Update
smc_ib_gid_check() to call smcr_port_err() after releasing the lock.
Fixes: 541afa10c1 ("net/smc: add smcr_port_err() and smcr_link_down() processing")
Reviewed-by: Mahanta Jambigi <mjambigi@linux.ibm.com>
Signed-off-by: Sidraya Jayagond <sidraya@linux.ibm.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Link: https://patch.msgid.link/20260922073149.474762-1-sidraya@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
__rds_conn_create() computes npaths from the caller's transport before
it decides whether a connection to one of the host's own addresses is
to be handled by the loopback transport instead. That substitution is
what an RDS/TCP socket sending to a local address gets, and after it
the path init loop still runs for the TCP transport's RDS_MPATH_WORKERS
paths and allocates an ordered workqueue for each, while
rds_loop_conn_alloc() only ever provides transport data for path 0.
rds_conn_destroy() sizes its teardown from c_trans, by then the
loopback transport, so it visits path 0 only - and
rds_conn_path_destroy() would skip the other paths anyway, since it
returns before destroy_workqueue() for a path without transport data.
kfree(c_path) then drops the last pointers to seven workqueues. That
repeats for every such connection, on every netns teardown or module
unload, and every distinct local destination address is a separate
connection.
Recompute npaths once the transport is final, so that creation and
destruction agree on the set of paths. The c_path array stays sized
for the caller's transport; the unused entries are freed with it.
Fixes: 4716af3897 ("net/rds: Give each connection path its own workqueue")
Signed-off-by: Allison Henderson <achender@kernel.org>
Link: https://patch.msgid.link/20260921215027.174657-1-achender@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
nfp_net_ipsec_rx() drops the XArray lock before taking a reference to the
xfrm_state it found. The delete path can erase the entry and drop the last
state reference in that interval. RX can then try to increment a zero
refcount after the state has been queued for destruction.
The driver queues firmware invalidation asynchronously; the delete path
does not wait for the command to complete or drain pending RX processing.
The XFRM garbage collector waits for an RCU grace period before freeing
the state. That delays reclamation but does not make acquiring a reference
from zero valid.
Take the xfrm_state reference before releasing the XArray lock so
xa_erase() cannot run between lookup and reference acquisition.
Fixes: 57f273adbc ("nfp: add framework to support ipsec offloading")
Reported-by: Changyul Lee <lcy8047@gmail.com>
Signed-off-by: Sang-Hoon Choi <csh0052@gmail.com>
Link: https://patch.msgid.link/179001455912.44752.17153022439349797877.idr-bug-92@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Guangshuo Li says:
====================
net: ena: fix resource cleanup on probe failure
This series fixes two resource leaks in the ena_probe() error path after
ena_device_init() has successfully initialized device resources.
Patch 1 adds the missing PHC cleanup.
Patch 2 adds the missing MMIO read request cleanup.
====================
Link: https://patch.msgid.link/20260921154202.471662-1-lgs201920130244@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ena_device_init() initializes the MMIO read mechanism with
ena_com_mmio_reg_read_request_init(), which allocates a coherent DMA
buffer for MMIO read responses.
The normal removal path releases this buffer through
ena_com_mmio_reg_read_request_destroy(). However, if ena_probe() fails
after ena_device_init() succeeds, the error path destroys the admin
resources and eventually frees ena_dev without destroying the MMIO read
request, leaving the coherent DMA buffer allocated.
Call ena_com_mmio_reg_read_request_destroy() in the probe error path
before releasing the remaining device resources.
This issue was found by manual code inspection.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Cc: stable@vger.kernel.org
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Link: https://patch.msgid.link/20260921154202.471662-3-lgs201920130244@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ena_probe() initializes the PHC as part of ena_device_init(), but the
probe failure path does not destroy it before freeing the PHC private
data.
The normal removal path calls ena_phc_destroy() through
ena_destroy_device() before ena_phc_free(). However, if probe fails
after ena_device_init() succeeds, the error path reaches ena_phc_free()
without unregistering the PTP clock or destroying the device PHC
resources.
Call ena_phc_destroy() in the probe error path before freeing the PHC
private data.
This issue was found by manual code inspection.
Cc: stable@vger.kernel.org tags and describe this as a consistency cleanup
Fixes: e0ea34158e ("net: ena: Add PHC support in the ENA driver")
Cc: stable@vger.kernel.org
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Cc: stable
Link: https://patch.msgid.link/20260921154202.471662-2-lgs201920130244@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ilya Maximets says:
====================
ovs, net/sched: fixes for UAF after conntrack extension realloc
One clean up change plus two fixes for the UAF on helper extension
realloc x 2. First half for OVS and the second half for the similar
code in act_ct. This should cover all the known cases of this problem
in these two modules.
====================
Link: https://patch.msgid.link/20260921145655.3167436-1-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While calling the helpers, a raw pointer to the extensions area is
wired into expectations list:
-> nf_ct_helper()
-> helper->help()
-> nf_ct_expect_related_report()
-> nf_ct_expect_insert()
-> hlist_add_head_rcu(&exp->lnode, &master_help->expectations)
In case the connection is not confirmed yet, more extensions can be
added afterwards with *_ext_add() calls reallocating the extension
space and leaving the now invalid pointer in the expectations list
that is later accessed while removing the expectation.
Make sure that helpers are called at the end after all the other
extensions are already added.
Note that the helper rejection now leaves the mark and labels set,
but that's not different from how the NAT was handled before or how
the mark and the labels were handled on confirmation failure. And
there are no atomicity guarantees provided by the API anyway.
Fixes: a21b06e731 ("net: sched: add helper support in act_ct")
Cc: stable@vger.kernel.org
Reported-by: Axel Mierczuk <axel.mierczuk@1password.com>
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Link: https://patch.msgid.link/20260921145655.3167436-7-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
