The platform_get_resource() function doesn't return error pointers, it
returns NULL on error. Update the error checking to match.
Fixes: 64d87ccfae ("spi: aspeed: Only map necessary address window region")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/aPJpEnfK31pHz8_w@stanley.mountain
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Benoît Monin <benoit.monin@bootlin.com>:
The DesignWare SPI controller can act as a host or a target; the
choice between the two is set in hardware and cannot be changed by
software. When configured in target mode, the controller has a much
reduced set of capabilities. It only has a single chip-select input and
can only run standard SPI mode (no dual, quad, or octal mode). Despite
this, the overall logic of doing an SPI transfer and the register layout
is identical between both modes, so implementing the target mode reuses
much of the existing code.
The first part of this two-patch series renames the spi_controller to
ctlr instead of host and also changes the suffix of the related functions
to controller. This is done to avoid confusion when referring to the
controller in target mode.
The second patch implements the target mode support by allocating an
SPI controller of the correct type based on the spi-slave property. The
controller is then configured differently depending on the mode. For
an SPI transfer, the same transfer_one() callback is used, with the
difference being in dw_spi_update_config() where only the CTRLR0
register is set. The other registers are not relevant in target mode
and are read-only.
I am posting this as an RFC because I could only perform partial testing
on my setup. I am using an SoC with two DesignWare SPI memory-mapped
controllers identified as Synopsys DWC APB SSI v4.03, one in host mode and
the other in target mode. On the evaluation board, a microcontroller acts
as an SPI relay between the two, but it has some limitations. The number
of bits per word is fixed, as are the clock phase and polarity. It also
only copies data from the host to the target. With this limited setup,
I did test that data can be successfully transferred from the host
to the target using spidev_test. I also checked that polling works by
temporarily disabling the IRQ, but I cannot test DMA. Therefore, more
testing on different devices would be welcome.
Merge series from Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>:
This patch series introduces several improvements to the
ASPEED SPI driver, targeting better stability, compatibility
and, flexibility across multiple ASPEED platforms.
Key changes include:
* Clock selection strategy update
Improves fallback logic when timing calibration is skipped or
fails, ensuring reliable boot behavior.
* Timing calibration enhancement for AST2600
Replaces the previous "first-pass" strategy with a more robust
algorithm that selects the optimal timing point.
* Default address decoding assignment
Ensures each chip select (CS) has a valid decoding range during
probe, avoiding detection failures due to missing or incorrect
bootloader setup.
* Centralized address decoding management
Refactors the decoding logic to centrally assign address windows,
preventing improper trimming and improving layout flexibility.
* Per-platform decoding adjustment
Introduces platform-specific `adjust_window` callbacks to handle
platform specific hardware constraints for address decoding range.
* Selective memory mapping
Optimizes memory usage by mapping only the required address window
per CS to avoid exhaustion.
Merge series from From git@z Thu Jan 1 00:00:00 1970
Axel Haslam <ahaslam@baylibre.com>:
Add an offset parameter that can be passed in the periodic trigger.
This is useful for example when ADC drivers implement a separate periodic
signal to trigger conversion and need offload to read the result with
some delay. While at it, add some documentation to offload periodic trigger
parameters.
IPQ5332 contains the QPIC-SPI-NAND flash controller which is the same as
the one found in IPQ9574. So let's document the IPQ5332 compatible and
use IPQ9574 as the fallback.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Link: https://patch.msgid.link/20251008090413.458791-3-quic_mdalam@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
IPQ5424 contains the QPIC-SPI-NAND flash controller which is the same as
the one found in IPQ9574. So let's document the IPQ5424 compatible and
use IPQ9574 as the fallback.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Link: https://patch.msgid.link/20251008090413.458791-2-quic_mdalam@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add an offset parameter that can be passed in the periodic trigger.
This is useful for example when ADC drivers implement a separate periodic
signal to trigger conversion and need offload to read the result with
some delay. While at it, add some documentation to offload periodic trigger
parameters.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://patch.msgid.link/cd315e95c0bd8523f00e91c400abcd6a418e5924.1759760519.git.marcelo.schmitt@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously, the driver mapped the entire SPI address decoding region during
probe. On systems with small flash or limited memory, this could lead to
excessive memory usage or allocation failures.
This patch changes the strategy to initially map a small address window
for SPI flash device probing. After determining each chip select's flash
size, the driver unmaps the temporary region and remaps only the required
address window accordingly.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Link: https://patch.msgid.link/20251001112605.1130723-7-chin-ting_kuo@aspeedtech.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Different ASPEED SoCs have specific limitations on SPI address decoding,
such as total range size, minimum window size per CS, and alignment
requirements. The original adjustment logic only handles simple cases
and could fail in more complex setups found in advanced board designs,
e.g., small flash on CS0 and large flash on CS1, or when the total physical
flash size exceeds the decoding range supported by the SPI controller.
This patch introduces a per-platform adjust_window callback to handle
these constraints properly. Each platform defines its own logic to
adjust decoding ranges, trim excess size, and ensure alignment.
If trimming is required, the affected CS will fall back to user mode
access to ensure the entire flash remains accessible from the MTD layer.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Link: https://patch.msgid.link/20251001112605.1130723-6-chin-ting_kuo@aspeedtech.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The original approach to handling address decoding overlaps was to trim
the next region directly. If the next CS's decoding range was fully
overlapped by the current one, it would be forcibly closed by trimming
its size to zero. This could lead expected behavior, especially on
the platform with multiple flashes layout.
To solve improper trimming problem, this patch collects the required
address decoding size at each stage, then, (re-)arragne address decoding
region to each CS centrally with knowing the total AHB decoding size.
If a segment register cannot be updated (e.g. due to bootloader write
protection), the original value is kept to avoid breaking access and
an error is reported if the total decoding size of all CS exceeds
the total AHB decoding size.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Link: https://patch.msgid.link/20251001112605.1130723-5-chin-ting_kuo@aspeedtech.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On some platforms, we cannot assume that the whole address decoding range
value is ready for each CS. Especially for chip selects other than CS0,
the address decoding range may not be properly configured before the kernel
stage, or the existing configuration may be unsuitable. This can lead to
SPI flash detection failures during driver probe.
To ensure reliable initialization, this patch forcibly assigns a default
address decoding range to each chip select based on a platform-specific
minimum window size. Unused chip selects are explicitly disabled to avoid
conflicts.
This change improves robustness across platforms with varying bootloader
behavior and ensures consistent SPI flash initialization.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Link: https://patch.msgid.link/20251001112605.1130723-4-chin-ting_kuo@aspeedtech.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Starting with the AST2600 platform, most platfom manufacturers have
adopted more complex board designs and signal routing, making SPI
timing calibration increasingly sensitive and critical. Previously,
the driver selected the first "PASS" timing point during calibration,
which may not yield the most stable result.
This patch introduces a more robust calibration method:
- It evaluates all combinations of HCLK sample point delay and DI input
delay. The results are stored in a 2D buffer for further comparison.
- Because the timing delay behavior is non-linear across HCLK sample
points, the optimal timing point is selected as the center of the
longest consecutive "PASS" interval within a single HCLK sample
point row.
This approach ensures better stability and precision in SPI read timing,
especially under complex signal integrity conditions.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Link: https://patch.msgid.link/20251001112605.1130723-3-chin-ting_kuo@aspeedtech.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch updates the SPI clock selection logic for cases where
timing calibration is not performed or the results are failed.
Timing calibration process is skipped in the two scenarios below.
- Low-entropy data in the calibration region:
The driver skips timing calibration if the data read from the
SPI flash contains mostly 0x00 or 0xFF. Originally, the driver
used a low-frequency clock to read this region as golden data.
However, due to variations in host characteristics and image
layout, we cannot assume sufficient entropy in this region to
ensure reliable calibration.
- Low-speed configurations (< 40MHz):
The ASPEED SPI controller does not support timing calibration when
the max_speed_hz of the SPI device is below 40MHz.
In both cases, the SPI clock frequency specified in the device tree
should be used directly. When timing calibration is skipped, it is
the board vendor's responsibility to ensure that the SPI flash
SI (Signal Integrity) is sufficient for reliable operation at the
configured frequency.
When timing calibration processes is execued and all potential clock
frequencies are performed, but are all failed, the lower clock frequency
should be adopted to ensure the overall system can boot up successfully.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Link: https://patch.msgid.link/20251001112605.1130723-2-chin-ting_kuo@aspeedtech.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement target mode for the DesignWare controller with the following
changes:
Allocate an SPI controller of the correct type based on the spi-slave
property in dw_spi_add_controller() and set the controller properties
depending on its type. Since they are only relevant when acting as a host
controller, settings related to chip-select control and the set_cs()
callback are only set in host mode, as are the loopback support, the
memory operations and the maximum frequency. The target_abort() callback
is set only when configured in target mode.
The number of chip-select is set to 1 in dw_spi_hw_init() since the
controller only has one CS input in target mode.
In dw_spi_update_config(), return after setting the CTRLR0 register as
the other registers are only relevant in host mode and are read-only
in target mode. This function is called as part of the transfer_one()
callback, which is identical in both the host and target mode.
Move the code implementing the handle_err() callback to a new function
named dw_spi_abort(), and use it to implement both the handle_err()
and the target_abort() callbacks.
Finally, drop the error path on the spi-slave property in
dw_spi_mmio_probe(), as it is now a valid configuration.
Signed-off-by: Benoît Monin <benoit.monin@bootlin.com>
Link: https://patch.msgid.link/20251002-spi-dw-target-v1-2-993e91c1a712@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the designware SPI controller can act as both a target and a host,
rename spi_controller member of the dw_spi struct to ctlr instead of host.
Similarly, rename the functions handling the controller, using controller
instead of host as the suffix.
No functional changes intended.
Signed-off-by: Benoît Monin <benoit.monin@bootlin.com>
Link: https://patch.msgid.link/20251002-spi-dw-target-v1-1-993e91c1a712@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
One revert because of a regression in the I2C core which has sadly not
showed up during its time in -next.
-----BEGIN PGP SIGNATURE-----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=b0xy
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.18-rc1-hotfix' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fix from Wolfram Sang:
"One revert because of a regression in the I2C core which has sadly not
showed up during its time in -next"
* tag 'i2c-for-6.18-rc1-hotfix' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
Revert "i2c: boardinfo: Annotate code used in init phase only"
reserved and accessing reserved register space could result in undefined
behavior
- Fix a function's retval check in aspeed-scu-ic
-----BEGIN PGP SIGNATURE-----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=dVwm
-----END PGP SIGNATURE-----
Merge tag 'irq_urgent_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Borislav Petkov:
- Skip interrupt ID 0 in sifive-plic during suspend/resume because
ID 0 is reserved and accessing reserved register space could result
in undefined behavior
- Fix a function's retval check in aspeed-scu-ic
* tag 'irq_urgent_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/sifive-plic: Avoid interrupt ID 0 handling during suspend/resume
irqchip/aspeed-scu-ic: Fix an IS_ERR() vs NULL check
The previous fix to trace_marker required updating trace_marker_raw
as well. The difference between trace_marker_raw from trace_marker
is that the raw version is for applications to write binary structures
directly into the ring buffer instead of writing ASCII strings.
This is for applications that will read the raw data from the ring
buffer and get the data structures directly. It's a bit quicker than
using the ASCII version.
Unfortunately, it appears that our test suite has several tests that
test writes to the trace_marker file, but lacks any tests to the
trace_marker_raw file (this needs to be remedied). Two issues came
about the update to the trace_marker_raw file that syzbot found:
- Fix tracing_mark_raw_write() to use per CPU buffer
The fix to use the per CPU buffer to copy from user space was needed for
both the trace_maker and trace_maker_raw file.
The fix for reading from user space into per CPU buffers properly fixed
the trace_marker write function, but the trace_marker_raw file wasn't
fixed properly. The user space data was correctly written into the per CPU
buffer, but the code that wrote into the ring buffer still used the user
space pointer and not the per CPU buffer that had the user space data
already written.
- Stop the fortify string warning from writing into trace_marker_raw
After converting the copy_from_user_nofault() into a memcpy(), another
issue appeared. As writes to the trace_marker_raw expects binary data, the
first entry is a 4 byte identifier. The entry structure is defined as:
struct {
struct trace_entry ent;
int id;
char buf[];
};
The size of this structure is reserved on the ring buffer with:
size = sizeof(*entry) + cnt;
Then it is copied from the buffer into the ring buffer with:
memcpy(&entry->id, buf, cnt);
This use to be a copy_from_user_nofault(), but now converting it to
a memcpy() triggers the fortify-string code, and causes a warning.
The allocated space is actually more than what is copied, as the cnt
used also includes the entry->id portion. Allocating sizeof(*entry)
plus cnt is actually allocating 4 bytes more than what is needed.
Change the size function to:
size = struct_size(entry, buf, cnt - sizeof(entry->id));
And update the memcpy() to unsafe_memcpy().
-----BEGIN PGP SIGNATURE-----
iIoEABYKADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCaOq0fhQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qr4HAQCNbFEDjzNNEueCWLOptC5YfeJgdvPB
399CzuFJl02ZOgD/flPJa1r+NaeYOBhe1BgpFF9FzB/SPXAXkXUGLM7WIgg=
=goks
-----END PGP SIGNATURE-----
Merge tag 'trace-v6.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
"The previous fix to trace_marker required updating trace_marker_raw as
well. The difference between trace_marker_raw from trace_marker is
that the raw version is for applications to write binary structures
directly into the ring buffer instead of writing ASCII strings. This
is for applications that will read the raw data from the ring buffer
and get the data structures directly. It's a bit quicker than using
the ASCII version.
Unfortunately, it appears that our test suite has several tests that
test writes to the trace_marker file, but lacks any tests to the
trace_marker_raw file (this needs to be remedied). Two issues came
about the update to the trace_marker_raw file that syzbot found:
- Fix tracing_mark_raw_write() to use per CPU buffer
The fix to use the per CPU buffer to copy from user space was
needed for both the trace_maker and trace_maker_raw file.
The fix for reading from user space into per CPU buffers properly
fixed the trace_marker write function, but the trace_marker_raw
file wasn't fixed properly. The user space data was correctly
written into the per CPU buffer, but the code that wrote into the
ring buffer still used the user space pointer and not the per CPU
buffer that had the user space data already written.
- Stop the fortify string warning from writing into trace_marker_raw
After converting the copy_from_user_nofault() into a memcpy(),
another issue appeared. As writes to the trace_marker_raw expects
binary data, the first entry is a 4 byte identifier. The entry
structure is defined as:
struct {
struct trace_entry ent;
int id;
char buf[];
};
The size of this structure is reserved on the ring buffer with:
size = sizeof(*entry) + cnt;
Then it is copied from the buffer into the ring buffer with:
memcpy(&entry->id, buf, cnt);
This use to be a copy_from_user_nofault(), but now converting it to
a memcpy() triggers the fortify-string code, and causes a warning.
The allocated space is actually more than what is copied, as the
cnt used also includes the entry->id portion. Allocating
sizeof(*entry) plus cnt is actually allocating 4 bytes more than
what is needed.
Change the size function to:
size = struct_size(entry, buf, cnt - sizeof(entry->id));
And update the memcpy() to unsafe_memcpy()"
* tag 'trace-v6.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Stop fortify-string from warning in tracing_mark_raw_write()
tracing: Fix tracing_mark_raw_write() to use buf and not ubuf
- Fix UAPI types check in headers_check.pl
- Only enable -Werror for hostprogs with CONFIG_WERROR / W=e
- Ignore fsync() error when output of gen_init_cpio is a pipe
- Several little build fixes for recent modules.builtin.modinfo series
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQR74yXHMTGczQHYypIdayaRccAalgUCaOqyGgAKCRAdayaRccAa
lhIaAP4owzRbZv/KnwVgXt3IDlAN7tOJQyiNbuAOTTH9IewvhAEA24zfrlav7CQl
WSc0d/poWAdmQJc0T/bdQ71G69j6dgQ=
=ljuS
-----END PGP SIGNATURE-----
Merge tag 'kbuild-fixes-6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux
Pull Kbuild fixes from Nathan Chancellor:
- Fix UAPI types check in headers_check.pl
- Only enable -Werror for hostprogs with CONFIG_WERROR / W=e
- Ignore fsync() error when output of gen_init_cpio is a pipe
- Several little build fixes for recent modules.builtin.modinfo series
* tag 'kbuild-fixes-6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux:
kbuild: Use '--strip-unneeded-symbol' for removing module device table symbols
s390/vmlinux.lds.S: Move .vmlinux.info to end of allocatable sections
kbuild: Add '.rel.*' strip pattern for vmlinux
kbuild: Restore pattern to avoid stripping .rela.dyn from vmlinux
gen_init_cpio: Ignore fsync() returning EINVAL on pipes
scripts/Makefile.extrawarn: Respect CONFIG_WERROR / W=e for hostprogs
kbuild: uapi: Strip comments before size type check
Fixes only in drivers (ufs, mvsas, qla2xxx, target) that came in just
before or during the merge window. The most important one is the
qla2xxx which reverts a conversion to fix flexible array member
warnings, that went up in this merge window but which turned out on
further testing to be causing data corruption.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iLgEABMIAGAWIQTnYEDbdso9F2cI+arnQslM7pishQUCaOpnUhsUgAAAAAAEAA5t
YW51MiwyLjUrMS4xMSwyLDImHGphbWVzLmJvdHRvbWxleUBoYW5zZW5wYXJ0bmVy
c2hpcC5jb20ACgkQ50LJTO6YrIUCFQEA1cADof79U9suDka2hAa2l7D4wJQ53qSj
R7CwarAVX2wA/3RaEHySnSk+ivyHRl5AOYlPrYsnBo1o2KUq1M6kfviM
=itgd
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Fixes only in drivers (ufs, mvsas, qla2xxx, target) that came in just
before or during the merge window.
The most important one is the qla2xxx which reverts a conversion to
fix flexible array member warnings, that went up in this merge window
but which turned out on further testing to be causing data corruption"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Include UTP error in INT_FATAL_ERRORS
scsi: ufs: sysfs: Make HID attributes visible
scsi: mvsas: Fix use-after-free bugs in mvs_work_queue
scsi: ufs: core: Fix PM QoS mutex initialization
scsi: ufs: core: Fix runtime suspend error deadlock
Revert "scsi: qla2xxx: Fix memcpy() field-spanning write issue"
scsi: target: target_core_configfs: Add length check to avoid buffer overflow
emulator in favor of int3_emulate_jcc() which is written in C
- Replace KVM fastops with C-based stubs which avoids problems with the
fastop infra related to latter not adhering to the C ABI due to their
special calling convention and, more importantly, bypassing compiler
control-flow integrity checking because they're written in asm
- Remove wrongly used static branches and other ugliness accumulated
over time in hyperv's hypercall implementation with a proper static
function call to the correct hypervisor call variant
- Add some fixes and modifications to allow running FRED-enabled kernels
in KVM even on non-FRED hardware
- Add kCFI improvements like validating indirect calls and prepare for
enabling kCFI with GCC. Add cmdline params documentation and other
code cleanups
- Use the single-byte 0xd6 insn as the official #UD single-byte
undefined opcode instruction as agreed upon by both x86 vendors
- Other smaller cleanups and touchups all over the place
-----BEGIN PGP SIGNATURE-----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=3Otb
-----END PGP SIGNATURE-----
Merge tag 'x86_core_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull more x86 updates from Borislav Petkov:
- Remove a bunch of asm implementing condition flags testing in KVM's
emulator in favor of int3_emulate_jcc() which is written in C
- Replace KVM fastops with C-based stubs which avoids problems with the
fastop infra related to latter not adhering to the C ABI due to their
special calling convention and, more importantly, bypassing compiler
control-flow integrity checking because they're written in asm
- Remove wrongly used static branches and other ugliness accumulated
over time in hyperv's hypercall implementation with a proper static
function call to the correct hypervisor call variant
- Add some fixes and modifications to allow running FRED-enabled
kernels in KVM even on non-FRED hardware
- Add kCFI improvements like validating indirect calls and prepare for
enabling kCFI with GCC. Add cmdline params documentation and other
code cleanups
- Use the single-byte 0xd6 insn as the official #UD single-byte
undefined opcode instruction as agreed upon by both x86 vendors
- Other smaller cleanups and touchups all over the place
* tag 'x86_core_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86,retpoline: Optimize patch_retpoline()
x86,ibt: Use UDB instead of 0xEA
x86/cfi: Remove __noinitretpoline and __noretpoline
x86/cfi: Add "debug" option to "cfi=" bootparam
x86/cfi: Standardize on common "CFI:" prefix for CFI reports
x86/cfi: Document the "cfi=" bootparam options
x86/traps: Clarify KCFI instruction layout
compiler_types.h: Move __nocfi out of compiler-specific header
objtool: Validate kCFI calls
x86/fred: KVM: VMX: Always use FRED for IRQs when CONFIG_X86_FRED=y
x86/fred: Play nice with invoking asm_fred_entry_from_kvm() on non-FRED hardware
x86/fred: Install system vector handlers even if FRED isn't fully enabled
x86/hyperv: Use direct call to hypercall-page
x86/hyperv: Clean up hv_do_hypercall()
KVM: x86: Remove fastops
KVM: x86: Convert em_salc() to C
KVM: x86: Introduce EM_ASM_3WCL
KVM: x86: Introduce EM_ASM_1SRC2
KVM: x86: Introduce EM_ASM_2CL
KVM: x86: Introduce EM_ASM_2W
...
version supports the =@ccCOND syntax
- Remove a bunch of AS_* Kconfig symbols which detect assembler support for
various instruction mnemonics now that the minimum assembler version
supports them all
- The usual cleanups all over the place
-----BEGIN PGP SIGNATURE-----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=dW6J
-----END PGP SIGNATURE-----
Merge tag 'x86_cleanups_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 cleanups from Borislav Petkov:
- Simplify inline asm flag output operands now that the minimum
compiler version supports the =@ccCOND syntax
- Remove a bunch of AS_* Kconfig symbols which detect assembler support
for various instruction mnemonics now that the minimum assembler
version supports them all
- The usual cleanups all over the place
* tag 'x86_cleanups_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm: Remove code depending on __GCC_ASM_FLAG_OUTPUTS__
x86/sgx: Use ENCLS mnemonic in <kernel/cpu/sgx/encls.h>
x86/mtrr: Remove license boilerplate text with bad FSF address
x86/asm: Use RDPKRU and WRPKRU mnemonics in <asm/special_insns.h>
x86/idle: Use MONITORX and MWAITX mnemonics in <asm/mwait.h>
x86/entry/fred: Push __KERNEL_CS directly
x86/kconfig: Remove CONFIG_AS_AVX512
crypto: x86 - Remove CONFIG_AS_VPCLMULQDQ
crypto: X86 - Remove CONFIG_AS_VAES
crypto: x86 - Remove CONFIG_AS_GFNI
x86/kconfig: Drop unused and needless config X86_64_SMP
preserve vmalloc allocations across handover.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCaOmDWAAKCRDdBJ7gKXxA
jh+MAQDUPBj3mFm238CXI5DC1gJ3ETe3NJjJvfzIjLs51c+dFgD+PUuvDA0GUtKH
LCl6T+HJXh2FgGn1F2Kl/0hwPtEvuA4=
=HYr7
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2025-10-10-15-03' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull more updates from Andrew Morton:
"Just one series here - Mike Rappoport has taught KEXEC handover to
preserve vmalloc allocations across handover"
* tag 'mm-nonmm-stable-2025-10-10-15-03' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
lib/test_kho: use kho_preserve_vmalloc instead of storing addresses in fdt
kho: add support for preserving vmalloc allocations
kho: replace kho_preserve_phys() with kho_preserve_pages()
kho: check if kho is finalized in __kho_preserve_order()
MAINTAINERS, .mailmap: update Umang's email address
All singletons, please see the changelogs for details.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCaOmCTwAKCRDdBJ7gKXxA
jtQZAQC9sRd+4LNYothoXlY9avKNYR4YvN3ogiIFJqHwiENu/QD/ec/57KME9dA4
H4SqK/49Rs/tVCYmkPTO7IWRmxo9/AA=
=h9On
-----END PGP SIGNATURE-----
Merge tag 'mm-hotfixes-stable-2025-10-10-15-00' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"7 hotfixes. All 7 are cc:stable and all 7 are for MM.
All singletons, please see the changelogs for details"
* tag 'mm-hotfixes-stable-2025-10-10-15-00' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm: hugetlb: avoid soft lockup when mprotect to large memory area
fsnotify: pass correct offset to fsnotify_mmap_perm()
mm/ksm: fix flag-dropping behavior in ksm_madvise
mm/damon/vaddr: do not repeat pte_offset_map_lock() until success
mm/rmap: fix soft-dirty and uffd-wp bit loss when remapping zero-filled mTHP subpage to shared zeropage
mm/thp: fix MTE tag mismatch when replacing zero-filled subpages
memcg: skip cgroup_file_notify if spinning is not allowed
The fix to use a per CPU buffer to read user space tested only the writes
to trace_marker. But it appears that the selftests are missing tests to
the trace_maker_raw file. The trace_maker_raw file is used by applications
that writes data structures and not strings into the file, and the tools
read the raw ring buffer to process the structures it writes.
The fix that reads the per CPU buffers passes the new per CPU buffer to
the trace_marker file writes, but the update to the trace_marker_raw write
read the data from user space into the per CPU buffer, but then still used
then passed the user space address to the function that records the data.
Pass in the per CPU buffer and not the user space address.
TODO: Add a test to better test trace_marker_raw.
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lore.kernel.org/20251011035243.386098147@kernel.org
Fixes: 64cf7d058a ("tracing: Have trace_marker use per-cpu data to read user space")
Reported-by: syzbot+9a2ede1643175f350105@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/68e973f5.050a0220.1186a4.0010.GAE@google.com/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
After commit 5ab23c7923 ("modpost: Create modalias for builtin
modules"), relocatable RISC-V kernels with CONFIG_KASAN=y start failing
when attempting to strip the module device table symbols:
riscv64-linux-objcopy: not stripping symbol `__mod_device_table__kmod_irq_starfive_jh8100_intc__of__starfive_intc_irqchip_match_table' because it is named in a relocation
make[4]: *** [scripts/Makefile.vmlinux:97: vmlinux] Error 1
The relocation appears to come from .LASANLOC5 in .data.rel.local:
$ llvm-objdump --disassemble-symbols=.LASANLOC5 --disassemble-all -r drivers/irqchip/irq-starfive-jh8100-intc.o
drivers/irqchip/irq-starfive-jh8100-intc.o: file format elf64-littleriscv
Disassembly of section .data.rel.local:
0000000000000180 <.LASANLOC5>:
...
1d0: 0000 unimp
00000000000001d0: R_RISCV_64 __mod_device_table__kmod_irq_starfive_jh8100_intc__of__starfive_intc_irqchip_match_table
...
This section appears to come from GCC for including additional
information about global variables that may be protected by KASAN.
There appears to be no way to opt out of the generation of these symbols
through either a flag or attribute. Attempting to remove '.LASANLOC*'
with '--strip-symbol' results in the same error as above because these
symbols may refer to (thus have relocation between) each other.
Avoid this build breakage by switching to '--strip-unneeded-symbol' for
removing __mod_device_table__ symbols, as it will only remove the symbol
when there is no relocation pointing to it. While this may result in a
little more bloat in the symbol table in certain configurations, it is
not as bad as outright build failures.
Fixes: 5ab23c7923 ("modpost: Create modalias for builtin modules")
Reported-by: Charles Mirabile <cmirabil@redhat.com>
Closes: https://lore.kernel.org/20251007011637.2512413-1-cmirabil@redhat.com/
Suggested-by: Alexey Gladkov <legion@kernel.org>
Tested-by: Nicolas Schier <nsc@kernel.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
amdgpu:
- DC DCE6 fixes
- GPU reset fixes
- Secure diplay messaging cleanup
- MES fix
- GPUVM locking fixes
- PMFW messaging cleanup
- PCI US/DS switch handling fix
- VCN queue reset fix
- DC FPU handling fix
- DCN 3.5 fix
- DC mirroring fix
amdkfd:
- Fix kfd process ref leak
- mmap write lock handling fix
- Fix comments in IOCTL
xe:
- Fix build with clang 16
- Fix handling of invalid configfs syntax usage and spell out the
expected syntax in the documentation
- Do not try late bind firmware when running as VF since it
shouldn't handle firmware loading
- Fix idle assertion for local BOs
- Fix uninitialized variable for late binding
- Do not require perfmon_capable to expose free memory at page
granularity. Handle it like other drm drivers do
- Fix lock handling on suspend error path
- Fix I2C controller resume after S3
v3d:
- fix fence locking
-----BEGIN PGP SIGNATURE-----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=tSAX
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2025-10-11-1' of https://gitlab.freedesktop.org/drm/kernel
Pull more drm fixes from Dave Airlie:
"Just the follow up fixes for rc1 from the next branch, amdgpu and xe
mostly with a single v3d fix in there.
amdgpu:
- DC DCE6 fixes
- GPU reset fixes
- Secure diplay messaging cleanup
- MES fix
- GPUVM locking fixes
- PMFW messaging cleanup
- PCI US/DS switch handling fix
- VCN queue reset fix
- DC FPU handling fix
- DCN 3.5 fix
- DC mirroring fix
amdkfd:
- Fix kfd process ref leak
- mmap write lock handling fix
- Fix comments in IOCTL
xe:
- Fix build with clang 16
- Fix handling of invalid configfs syntax usage and spell out the
expected syntax in the documentation
- Do not try late bind firmware when running as VF since it shouldn't
handle firmware loading
- Fix idle assertion for local BOs
- Fix uninitialized variable for late binding
- Do not require perfmon_capable to expose free memory at page
granularity. Handle it like other drm drivers do
- Fix lock handling on suspend error path
- Fix I2C controller resume after S3
v3d:
- fix fence locking"
* tag 'drm-next-2025-10-11-1' of https://gitlab.freedesktop.org/drm/kernel: (34 commits)
drm/amd/display: Incorrect Mirror Cositing
drm/amd/display: Enable Dynamic DTBCLK Switch
drm/amdgpu: Report individual reset error
drm/amdgpu: partially revert "revert to old status lock handling v3"
drm/amd/display: Fix unsafe uses of kernel mode FPU
drm/amd/pm: Disable VCN queue reset on SMU v13.0.6 due to regression
drm/amdgpu: Fix general protection fault in amdgpu_vm_bo_reset_state_machine
drm/amdgpu: Check swus/ds for switch state save
drm/amdkfd: Fix two comments in kfd_ioctl.h
drm/amd/pm: Avoid interface mismatch messaging
drm/amdgpu: Merge amdgpu_vm_set_pasid into amdgpu_vm_init
drm/amd/amdgpu: Fix the mes version that support inv_tlbs
drm/amd: Check whether secure display TA loaded successfully
drm/amdkfd: Fix mmap write lock not release
drm/amdkfd: Fix kfd process ref leaking when userptr unmapping
drm/amdgpu: Fix for GPU reset being blocked by KIQ I/O.
drm/amd/display: Disable scaling on DCE6 for now
drm/amd/display: Properly disable scaling on DCE6
drm/amd/display: Properly clear SCL_*_FILTER_CONTROL on DCE6
drm/amd/display: Add missing DCE6 SCL_HORZ_FILTER_INIT* SRIs
...
nouveau:
- Return errno code from TTM move helper
vmwgfx:
- Fix null-ptr access in cursor code
- Fix UAF in validation
- Use correct iterator in validation
-----BEGIN PGP SIGNATURE-----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=ov4p
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2025-10-11' of https://gitlab.freedesktop.org/drm/kernel
Pull drm fixes from Dave Airlie:
"Some fixes leftover from our fixes branch, just nouveau and vmwgfx:
nouveau:
- Return errno code from TTM move helper
vmwgfx:
- Fix null-ptr access in cursor code
- Fix UAF in validation
- Use correct iterator in validation"
* tag 'drm-fixes-2025-10-11' of https://gitlab.freedesktop.org/drm/kernel:
drm/nouveau: fix bad ret code in nouveau_bo_move_prep
drm/vmwgfx: Fix copy-paste typo in validation
drm/vmwgfx: Fix Use-after-free in validation
drm/vmwgfx: Fix a null-ptr access in the cursor snooper
- Allow child nodes on renesas-bsc bus binding
- Drop node name pattern on allwinner,sun50i-a64-de2 bus binding
- Switch DT patchwork to kernel.org from ozlabs.org
- Fix some typos in docs and bindings
- Fix reference count in PCI node unittest
-----BEGIN PGP SIGNATURE-----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=7vRd
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Allow child nodes on renesas-bsc bus binding
- Drop node name pattern on allwinner,sun50i-a64-de2 bus binding
- Switch DT patchwork to kernel.org from ozlabs.org
- Fix some typos in docs and bindings
- Fix reference count in PCI node unittest
* tag 'devicetree-fixes-for-6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: bus: renesas-bsc: allow additional properties
dt-bindings: bus: allwinner,sun50i-a64-de2: don't check node names
MAINTAINERS: Move DT patchwork to kernel.org
of: unittest: Fix device reference count leak in of_unittest_pci_node_verify
of: doc: Fix typo in doc comments.
dt-bindings: mmc: Correct typo "upto" to "up to"
Allow additional properties to enable devices attached to the bus.
Fixes warnings like these:
arch/arm/boot/dts/renesas/sh73a0-kzm9g.dtb: bus@fec10000 (renesas,bsc-sh73a0): Unevaluated properties are not allowed ('ethernet@10000000' was unexpected)
arch/arm/boot/dts/renesas/r8a73a4-ape6evm.dtb: bus@fec10000 (renesas,bsc-r8a73a4): Unevaluated properties are not allowed ('ethernet@8000000', 'flash@0' were unexpected)
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Node names are already and properly checked by the core schema. No need
to do it again.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[robh: Also drop [A-F] in unit address]
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
issue (also affected userspace) of incorrect permissions being granted
to users who have access to multiple different CephFS instances within
the same cluster from Kotresh and a bunch of assorted CephFS fixes from
Slava.
-----BEGIN PGP SIGNATURE-----
iQFFBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAmjpShsTHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzizoaB/C7qTw5Olh8NDpX8I+ljEO50XNduurf
fp2eNn0ub5brhcvh8iACSPKE2oer/bDvv3b2SN9310GmBX3f7H2Ht5TeH2tGBRN0
clg+C2DmY/2watHovo+ua7YAd+HiPH2XMbpeU38Pu1nEdmiU6cQ0YaOn8n2p+c1E
bID0dMHWb4HTmFRURqWqKPDkM1fLHRxIVgyOMaov5vs0T7XdglwPja3S2W6epvqF
hKSMSvO/j9qYlOsBM6G6IuHDMJomzBqOQKqsQqC4XZN6uXeaKPTLYRnzxKfJUEWj
P5JTaum7NGGtfIs0L9wr6zpou/GY2zTFiyXhLZsLJMn894bBO5nArg==
=wGIB
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-6.18-rc1' of https://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
- some messenger improvements (Eric and Max)
- address an issue (also affected userspace) of incorrect permissions
being granted to users who have access to multiple different CephFS
instances within the same cluster (Kotresh)
- a bunch of assorted CephFS fixes (Slava)
* tag 'ceph-for-6.18-rc1' of https://github.com/ceph/ceph-client:
ceph: add bug tracking system info to MAINTAINERS
ceph: fix multifs mds auth caps issue
ceph: cleanup in ceph_alloc_readdir_reply_buffer()
ceph: fix potential NULL dereference issue in ceph_fill_trace()
libceph: add empty check to ceph_con_get_out_msg()
libceph: pass the message pointer instead of loading con->out_msg
libceph: make ceph_con_get_out_msg() return the message pointer
ceph: fix potential race condition on operations with CEPH_I_ODIRECT flag
ceph: refactor wake_up_bit() pattern of calling
ceph: fix potential race condition in ceph_ioctl_lazyio()
ceph: fix overflowed constant issue in ceph_do_objects_copy()
ceph: fix wrong sizeof argument issue in register_session()
ceph: add checking of wait_for_completion_killable() return value
ceph: make ceph_start_io_*() killable
libceph: Use HMAC-SHA256 library instead of crypto_shash
-----BEGIN PGP SIGNATURE-----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=/qIG
-----END PGP SIGNATURE-----
Merge tag 'v6.18-rc-part2-smb-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull more smb client updates from Steve French:
- fix i_size in fallocate
- two truncate fixes
- utime fix
- minor cleanups
- SMB1 fixes
- improve error check in read
- improve perf of copy file_range (copy_chunk)
* tag 'v6.18-rc-part2-smb-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal version number
cifs: Add comments for DeletePending assignments in open functions
cifs: Add fallback code path for cifs_mkdir_setinfo()
cifs: Allow fallback code in smb_set_file_info() also for directories
cifs: Query EA $LXMOD in cifs_query_path_info() for WSL reparse points
smb: client: remove cfids_invalidation_worker
smb: client: remove redudant assignment in cifs_strict_fsync()
smb: client: fix race with fallocate(2) and AIO+DIO
smb: client: fix missing timestamp updates after utime(2)
smb: client: fix missing timestamp updates after ftruncate(2)
smb: client: fix missing timestamp updates with O_TRUNC
cifs: Fix copy_to_iter return value check
smb: client: batch SRV_COPYCHUNK entries to cut round trips
smb: client: Omit an if branch in smb2_find_smb_tcon()
smb: client: Return directly after a failed genlmsg_new() in cifs_swn_send_register_message()
smb: client: Use common code in cifs_do_create()
smb: client: Improve unlocking of a mutex in cifs_get_swn_reg()
smb: client: Return a status code only as a constant in cifs_spnego_key_instantiate()
smb: client: Use common code in cifs_lookup()
smb: client: Reduce the scopes for a few variables in two functions
- minor cleanups
-----BEGIN PGP SIGNATURE-----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=ZBiX
-----END PGP SIGNATURE-----
Merge tag 'xtensa-20251010' of https://github.com/jcmvbkbc/linux-xtensa
Pull Xtensa updates from Max Filippov:
- minor cleanups
* tag 'xtensa-20251010' of https://github.com/jcmvbkbc/linux-xtensa:
xtensa: use HZ_PER_MHZ in platform_calibrate_ccount
xtensa: simdisk: add input size check in proc_write_simdisk
-----BEGIN PGP SIGNATURE-----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=/1jf
-----END PGP SIGNATURE-----
Merge tag 'block-6.18-20251009' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux
Pull block fixes from Jens Axboe:
- Don't include __GFP_NOWARN for loop worker allocation, as it already
uses GFP_NOWAIT which has __GFP_NOWARN set already
- Small series cleaning up the recent bio_iov_iter_get_pages() changes
- loop fix for leaking the backing reference file, if validation fails
- Update of a comment pertaining to disk/partition stat locking
* tag 'block-6.18-20251009' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
loop: remove redundant __GFP_NOWARN flag
block: move bio_iov_iter_get_bdev_pages to block/fops.c
iomap: open code bio_iov_iter_get_bdev_pages
block: rename bio_iov_iter_get_pages_aligned to bio_iov_iter_get_pages
block: remove bio_iov_iter_get_pages
block: Update a comment of disk statistics
loop: fix backing file reference leak on validation error
-----BEGIN PGP SIGNATURE-----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=p4O+
-----END PGP SIGNATURE-----
Merge tag 'io_uring-6.18-20251009' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux
Pull io_uring fixes from Jens Axboe:
- Fixup indentation in the UAPI header
- Two fixes for zcrx. One fixes receiving too much in some cases, and
the other deals with not correctly incrementing the source in the
fallback copy loop
- Fix for a race in the IORING_OP_WAITID command, where there was a
small window where the request would be left on the wait_queue_head
list even though it was being canceled/completed
- Update liburing git URL in the kernel tree
* tag 'io_uring-6.18-20251009' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
io_uring/zcrx: increment fallback loop src offset
io_uring/zcrx: fix overshooting recv limit
io_uring: use tab indentation for IORING_SEND_VECTORIZED comment
io_uring/waitid: always prune wait queue entry in io_waitid_wait()
io_uring: update liburing git URL
This is a series to address some problems that were exposed by the
recent modules.builtin.modinfo series that landed in commit c7d3dd9163
("Merge patch series "Add generated modalias to
modules.builtin.modinfo"").
The third patch is not directly related to the aforementioned series, as
the warning it fixes happens prior to the series but commit 8d18ef04f9
("s390: vmlinux.lds.S: Reorder sections") from the series creates
conflicts in this area, so I included it here.
Link: https://patch.msgid.link/20251008-kbuild-fix-modinfo-regressions-v1-0-9fc776c5887c@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
When building s390 defconfig with binutils older than 2.32, there are
several warnings during the final linking stage:
s390-linux-ld: .tmp_vmlinux1: warning: allocated section `.got.plt' not in segment
s390-linux-ld: .tmp_vmlinux2: warning: allocated section `.got.plt' not in segment
s390-linux-ld: vmlinux.unstripped: warning: allocated section `.got.plt' not in segment
s390-linux-objcopy: vmlinux: warning: allocated section `.got.plt' not in segment
s390-linux-objcopy: st7afZyb: warning: allocated section `.got.plt' not in segment
binutils commit afca762f598 ("S/390: Improve partial relro support for
64 bit") [1] in 2.32 changed where .got.plt is emitted, avoiding the
warning.
The :NONE in the .vmlinux.info output section description changes the
segment for subsequent allocated sections. Move .vmlinux.info right
above the discards section to place all other sections in the previously
defined segment, .data.
Fixes: 30226853d6 ("s390: vmlinux.lds.S: explicitly handle '.got' and '.plt' sections")
Link: https://sourceware.org/git/?p=binutils-gdb.git;a=commit;h=afca762f598d453c563f244cd3777715b1a0cb72 [1]
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Acked-by: Alexey Gladkov <legion@kernel.org>
Acked-by: Nicolas Schier <nsc@kernel.org>
Link: https://patch.msgid.link/20251008-kbuild-fix-modinfo-regressions-v1-3-9fc776c5887c@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Prior to binutils commit c12d9fa2afe ("Support objcopy
--remove-section=.relaFOO") [1] in 2.32, stripping relocation sections
required the trailing period (i.e., '.rel.*') to work properly.
After commit 3e86e4d74c ("kbuild: keep .modinfo section in
vmlinux.unstripped"), there is an error with binutils 2.31.1 or earlier
because these sections are not properly removed:
s390-linux-objcopy: st6tO8Ev: symbol `.modinfo' required but not present
s390-linux-objcopy:st6tO8Ev: no symbols
Add the old pattern to resolve this issue (along with a comment to allow
cleaning this when binutils 2.32 or newer is the minimum supported
version). While the aforementioned kbuild change exposes this, the
pattern was originally changed by commit 71d815bf5d ("kbuild: Strip
runtime const RELA sections correctly"), where it would still be
incorrect with binutils older than 2.32.
Fixes: 71d815bf5d ("kbuild: Strip runtime const RELA sections correctly")
Link: https://sourceware.org/git/?p=binutils-gdb.git;a=commit;h=c12d9fa2afe7abcbe407a00e15719e1a1350c2a7 [1]
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Closes: https://lore.kernel.org/CA+G9fYvVktRhFtZXdNgVOL8j+ArsJDpvMLgCitaQvQmCx=hwOQ@mail.gmail.com/
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Alexey Gladkov <legion@kernel.org>
Acked-by: Nicolas Schier <nsc@kernel.org>
Link: https://patch.msgid.link/20251008-kbuild-fix-modinfo-regressions-v1-2-9fc776c5887c@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
