Since we have already in BH context when *_write_space(),
*_data_ready() as well as *_state_change() are called, it's
unnecessary to disable BH.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the "bonding" driver does not support load balancing outgoing
traffic in LACP mode for IPv6 traffic. IPv4 (and TCP or UDP over IPv4)
are currently supported; this patch adds transmit hashing for IPv6 (and
TCP or UDP over IPv6), bringing IPv6 up to par with IPv4 support in the
bonding driver. In addition, bounds checking has been added to all
transmit hashing functions.
The algorithm chosen (xor'ing the bottom three quads of the source and
destination addresses together, then xor'ing each byte of that result into
the bottom byte, finally xor'ing with the last bytes of the MAC addresses)
was selected after testing almost 400,000 unique IPv6 addresses harvested
from server logs. This algorithm had the most even distribution for both
big- and little-endian architectures while still using few instructions. Its
behavior also attempts to closely match that of the IPv4 algorithm.
The IPv6 flow label was intentionally not included in the hash as it appears
to be unset in the vast majority of IPv6 traffic sampled, and the current
algorithm not using the flow label already offers a very even distribution.
Fragmented IPv6 packets are handled the same way as fragmented IPv4 packets,
ie, they are not balanced based on layer 4 information. Additionally,
IPv6 packets with intermediate headers are not balanced based on layer
4 information. In practice these intermediate headers are not common and
this should not cause any problems, and the alternative (a packet-parsing
loop and look-up table) seemed slow and complicated for little gain.
Tested-by: John Eaglesham <linux@8192.net>
Signed-off-by: John Eaglesham <linux@8192.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6gre_err() miscomputes grehlen (sizeof(ipv6h) is 4 or 8,
not 40 as expected), and should take into account 'offset' parameter.
Also uses pskb_may_pull() to cope with some fragged skbs
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts commit 56892261ed (xfrm: Use rcu_dereference_bh to
deference pointer protected by rcu_read_lock_bh), and fixes bugs
introduced in commit 418a99ac6a ( Replace rwlock on xfrm_policy_afinfo
with rcu )
1) We properly use RCU variant in this file, not a mix of RCU/RCU_BH
2) We must defer some writes after the synchronize_rcu() call or a reader
can crash dereferencing NULL pointer.
3) Now we use the xfrm_policy_afinfo_lock spinlock only from process
context, we no longer need to block BH in xfrm_policy_register_afinfo()
and xfrm_policy_unregister_afinfo()
4) Can use RCU_INIT_POINTER() instead of rcu_assign_pointer() in
xfrm_policy_unregister_afinfo()
5) Remove a forward inline declaration (xfrm_policy_put_afinfo()),
and also move xfrm_policy_get_afinfo() declaration.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Fan Du <fan.du@windriver.com>
Cc: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old interface is bugged and reads the wrong sensor when retrieving
the reading for the chassis fan (it reads the CPU sensor); the new
interface works fine.
Reported-by: Göran Uddeborg <goeran@uddeborg.se>
Cc: stable@vger.kernel.org
Tested-by: Göran Uddeborg <goeran@uddeborg.se>
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Daniel writes:
" First -next pull for 3.7. Highlights:
- hsw hdmi improvements (Paulo)
- ips/rps locking rework and cleanups
- rc6 on ilk by default again
- hw context&dp&dpff support for hsw (Ben)
- GET_PARAM_HAS_SEMAPHORES (Chris)
- gen6+ pipe_control improvements (Chris)
- set_cacheing ioctl and assorted support code (Chris)
- cleanups around the busy/idle/pm code (Chris&me)
- flushing_list removal, hopefully for good (Chris)
- read_reg ioctl (Ben)
- support the ns2501 dvo (Thomas Richter)
- avoid the costly gen6+ "missed IRQ" workaround where we don't need a
race-free seqno readback (Chris)
- various bits&pieces, mostly early patches from the modeset rework branch"
* 'for-airlied' of git://people.freedesktop.org/~danvet/drm-intel: (54 commits)
drm/i915: don't grab dev->struct_mutex for userspace forcewak
drm/i915: try harder to find WR PLL clock settings
drm/i915: use the correct encoder type when comparing
drm/i915: Lazily apply the SNB+ seqno w/a
drm/i915: enable rc6 on ilk again
drm/i915: fix up ilk drps/ips locking
drm/i915: DE_PCU_EVENT irq is ilk-only
drm/i915: kill dev_priv->mchdev_lock
drm/i915: move all rps state into dev_priv->rps
drm/i915: use mutex_lock_interruptible for debugfs files
drm/i915: fixup up debugfs rps state handling
drm/i915: properly guard ilk ips state
drm/i915: add parentheses around PIXCLK_GATE definitions
drm/i915: reindent Haswell register definitions
drm/i915: completely reset the value of DDI_FUNC_CTL
drm/i915: correctly set the DDI_FUNC_CTL bpc field
drm/i915: set the DDI sync polarity bits
drm/i915: fix pipe DDI mode select
drm/i915: dump the device info
drm/i915: fixup desired rps frequency computation
...
There are different types of chargers avalibale like AC, Solar, USB,
etc.. Even in USB we have different types SDP/DCP/CDP/ACA and all these
chargers have different o/p ratings. For example SDP supports only 500mA
of charge current whereas AC charger can support upto 8A or more.
Similarly batteries also come with charge current and voltage ratings
and these ratings vary depending on its capacity and the technology
used.
This patch adds two new power supply properties
CONSTANT_CHARGE_CURRENT_MAX and CONSTANT_CHARGE_CURRENT_MAX.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
I noticed extra one second delay in device dismantle, tracked down to
a call to dst_dev_event() while some call_rcu() are still in RCU queues.
These call_rcu() were posted by rt_free(struct rtable *rt) calls.
We then wait a little (but one second) in netdev_wait_allrefs() before
kicking again NETDEV_UNREGISTER.
As the call_rcu() are now completed, dst_dev_event() can do the needed
device swap on busy dst.
To solve this problem, add a new NETDEV_UNREGISTER_FINAL, called
after a rcu_barrier(), but outside of RTNL lock.
Use NETDEV_UNREGISTER_FINAL with care !
Change dst_dev_event() handler to react to NETDEV_UNREGISTER_FINAL
Also remove NETDEV_UNREGISTER_BATCH, as its not used anymore after
IP cache removal.
With help from Gao feng
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comment says that charger_regulators is an array of
regulator_bulk_data, which is not true, since it's actually a pointer
to 'struct charger_regulator'.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This patch remove unnecessary variable(cm->fullbatt_vchk_uV) by using
'desc->fullbatt_uV' field directly in fullbatt_handler() function
to check the state of battery.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This patch disable regulator for charging when charger cable is detached
before stopping charging forcibly on abnormal battery state and check
return value of regulator_enable/disable() function to confirm correct
operation of enabling or disabling regulator for charging.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Noticed the new warning:
CHECK drivers/power/da9030_battery.c
drivers/power/da9030_battery.c:190:68: warning: Using plain integer as NULL pointer
This commit fixes the issue.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
It is possible that users can use non-standard chargers or use invalid
batteries especially with mobile devices.
This patch adds a new power supply property called 'AUTHENTIC' to
indicate this to the user(user space).
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
With devm_kzalloc there is no need of freeing at the errorpath and also
at unregister it.
Signed-off-by: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
module_platform_driver can be used to replace the platform_driver
register and unregister functions, with the calls to module_init
and module_exit,
i.e. all the code that is doing like the below
static int __init mymod_init(void)
{
return platform_driver_register(&drv_operations);
}
static void __exit mymod_exit(void)
{
platform_driver_unregister(&drv_operations);
}
module_init(mymod_init);
module_exit(mymod_exit);
can be replaced with
module_platform_driver(drv_operations)...
Signed-off-by: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
It would be better not to use the 0b-prefix for earlier versions of
gcc-4.3.
Signed-off-by: Il Han <corone.il.han@gmail.com>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
The fix for MFD part is already merged so we can remove the broken mark
for da9052-battery.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
The patch fixes the following warnings:
CHECK drivers/power/da9052-battery.c
drivers/power/da9052-battery.c:330:15: warning: symbol 'da9052_determine_vc_tbl_index' was not declared. Should it be static?
CC drivers/power/da9052-battery.o
drivers/power/da9052-battery.c: In function 'da9052_determine_vc_tbl_index':
drivers/power/da9052-battery.c:348:1: warning: control reaches end of non-void function [-Wreturn-type]
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This patch fixes the name of the macro used to mask the
mmc interrupt: erroneously it was used: MMC_DEFAUL_MASK.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Erroneously the DWMAC_CORE_3_40 was set to 34 instead of 0x34.
This can generate problems when run on old chips because
the driver assumes that there are the extra 16 regs available
for perfect filtering.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Gianni Antoniazzi <gianni.antoniazzi-ext@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sylvain Munault reported following info :
- TCP connection get "stuck" with data in send queue when doing
"large" transfers ( like typing 'ps ax' on a ssh connection )
- Only happens on path where the PMTU is lower than the MTU of
the interface
- Is not present right after boot, it only appears 10-20min after
boot or so. (and that's inside the _same_ TCP connection, it works
fine at first and then in the same ssh session, it'll get stuck)
- Definitely seems related to fragments somehow since I see a router
sending ICMP message saying fragmentation is needed.
- Exact same setup works fine with kernel 3.5.1
Problem happens when the 10 minutes (ip_rt_mtu_expires) expiration
period is over.
ip_rt_update_pmtu() calls dst_set_expires() to rearm a new expiration,
but dst_set_expires() does nothing because dst.expires is already set.
It seems we want to set the expires field to a new value, regardless
of prior one.
With help from Julian Anastasov.
Reported-by: Sylvain Munaut <s.munaut@whatever-company.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
CC: Julian Anastasov <ja@ssi.bg>
Tested-by: Sylvain Munaut <s.munaut@whatever-company.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if usb power supply registration fails,
we wont unregister the ac power supply
if battery power supply registration fails,
we wont unregister the usb, and ac supply,
take care of those things and also no need of goto -err_mem: at the fail case of
kzalloc simply can have return -ENOMEM
Signed-off-by: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Olinuxino has a LED connected to MX23_PAD_SSP1_DETECT__GPIO_2_1 pin.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Instead of assigning SSP1_DETECT inside mmc0_4bit_pins_a, let the board dts
handle this setup.
Not every board will use MX23_PAD_SSP1_DETECT as SSP1 functionality.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
hog_pins is used to setup the pin functions, and it is not neccesarily used only
for GPIO pins, so use only 'hog' to describe a more generic term.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Pablo Neira Ayuso says:
====================
This is the first batch of Netfilter and IPVS updates for your
net-next tree. Mostly cleanups for the Netfilter side. They are:
* Remove unnecessary RTNL locking now that we have support
for namespace in nf_conntrack, from Patrick McHardy.
* Cleanup to eliminate unnecessary goto in the initialization
path of several Netfilter tables, from Jean Sacren.
* Another cleanup from Wu Fengguang, this time to PTR_RET instead
of if IS_ERR then return PTR_ERR.
* Use list_for_each_entry_continue_rcu in nf_iterate, from
Michael Wang.
* Add pmtu_disc sysctl option to disable PMTU in their tunneling
transmitter, from Julian Anastasov.
* Generalize application protocol registration in IPVS and modify
IPVS FTP helper to use it, from Julian Anastasov.
* update Kconfig. The IPVS FTP helper depends on the Netfilter FTP
helper for NAT support, from Julian Anastasov.
* Add logic to update PMTU for IPIP packets in IPVS, again
from Julian Anastasov.
* A couple of sparse warning fixes for IPVS and Netfilter from
Claudiu Ghioc and Patrick McHardy respectively.
Patrick's IPv6 NAT changes will follow after this batch, I need
to flush this batch first before refreshing my tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize return variable before exiting on an error path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Initialize return variable before exiting on an error path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Initialize return variable before exiting on an error path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Initialize return variable before exiting on an error path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Initialize return variable before exiting on an error path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Noticed when digging into a suspend issue in linux-next (next-20120821).
For more details see <http://marc.info/?t=134554708000002&r=1&w=2>.
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Limit the access to userspace only on the BSP where we load the
container, verify the patches in it and put them in the patch cache.
Then, at application time, we lookup the correct patch in the cache and
use it.
When we need to reload the userspace container, we do that over the
reload interface:
echo 1 > /sys/devices/system/cpu/microcode/reload
which reloads (a possibly newer) container from userspace and applies
then the newest patches from there.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1344361461-10076-13-git-send-email-bp@amd64.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This is a trivial cache which collects all ucode patches for the current
family of CPUs on the system. If a newer patch appears due to the
container file being updated in userspace, we replace our cached version
with the new one.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1344361461-10076-12-git-send-email-bp@amd64.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
We search the equivalence table using the CPUID(1) signature of the
CPU in order to get the equivalence ID of the patch which we need to
apply. Add a function which does the reverse - it will be needed in
later patches.
While at it, pull the other equiv table function up in the file so that
it can be used by other functionality without forward declarations.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1344361461-10076-11-git-send-email-bp@amd64.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This is done in preparation for teaching the ucode driver to either load
a new ucode patches container from userspace or use an already cached
version. No functionality change in this patch.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1344361461-10076-10-git-send-email-bp@amd64.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Read the CPUID(1).EAX leaf at the correct cpu and use it to search the
equivalence table for matching microcode patch. No functionality change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1344361461-10076-9-git-send-email-bp@amd64.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Make sure we're actually applying a microcode patch to a core which
really needs it.
This brings only a very very very minor slowdown on F10:
0.032218828 sec vs 0.056010626 sec with this patch.
And small speedup on F15:
0.487089449 sec vs 0.180551162 sec (from perf output).
Also, fixup comments while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1344361461-10076-8-git-send-email-bp@amd64.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
get_ucode_data was a trivial memcpy wrapper. Remove it so as not to
obfuscate code unnecessarily with no obvious gain.
No functional change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1344361461-10076-7-git-send-email-bp@amd64.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Mask out CPU_TASKS_FROZEN bit so that all _FROZEN cases can be dropped.
Also, add some more comments as to why CPU_ONLINE falls through to
CPU_DOWN_FAILED (no break), and for the CPU_DEAD case. Realign debug
printks better.
Idea blatantly stolen from a tglx patch:
http://marc.info/?l=linux-kernel&m=134267779513862
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1344361461-10076-5-git-send-email-bp@amd64.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Remove the uci->mc check on the cpu resume path because the low-level
drivers do that anyway.
More importantly, though, this fixes a contrived and obscure but still
important case. Imagine the following:
* boot machine, no new microcode in /lib/firmware
* a subset of the CPUs is offlined
* in the meantime, user puts new fresh microcode container into
/lib/firmware and reloads it by doing
$ echo 1 > /sys/devices/system/cpu/microcode/reload
* offlined cores come back online and they don't get the newer microcode
applied due to this check.
Later patches take care of the issue on AMD.
While at it, cleanup code around it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1344361461-10076-4-git-send-email-bp@amd64.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Invert the uci->valid check so that the later block can be aligned on
the first indentation level of the function. No functional change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1344361461-10076-3-git-send-email-bp@amd64.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This issue was recently observed on an AMD C-50 CPU where a patch of
maximum size was applied.
Commit be62adb492 ("x86, microcode, AMD: Simplify ucode verification")
added current_size in get_matching_microcode(). This is calculated as
size of the ucode patch + 8 (ie. size of the header). Later this is
compared against the maximum possible ucode patch size for a CPU family.
And of course this fails if the patch has already maximum size.
Cc: <stable@vger.kernel.org> [3.3+]
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1344361461-10076-1-git-send-email-bp@amd64.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Lantiq socs have a General Purpose Timer Unit (GPTU). This driver allows us to
initialize the timers. The voice firmware needs these timers as a reference.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4236/
The xrx200 SoC family has the same PCI clock register layout as the AR9.
Enable the same quirk as for AR9
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4235/
As a result of a non populated ->bits field inside the clock struct, the clock
domains were never powered on the Falcon. Until now we only used domains that
were also used and powered by the bootloader.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4234/
Register nmi and ejtag bootrom vectors for FALC-ON SoC.
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4238/
Support for the external interrupt unit was broken when the code was converted
to devicetree support.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4231/
