In order for indirect mode on the PIXIS to work properly, both chip selects
need to be set to GPCM mode, otherwise writes to the chip select base
addresses will not actually post to the local bus -- they'll go to the
NAND controller instead. Therefore, we need to set BR0 and BR1 to GPCM
mode before switching to indirect mode.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale P1022 has a unique pin muxing "feature" where the DIU video
controller's video signals are muxed with 24 of the local bus address signals.
When the DIU is enabled, the bulk of the local bus is disabled, preventing
access to memory-mapped devices like NAND flash and the pixis FPGA.
Therefore, if the DIU is going to be enabled, then memory-mapped devices on
the localbus, like NAND flash, need to be disabled.
This patch is similar to "powerpc/85xx: p1022ds: disable the NOR flash node
if video is enabled", except that it disables the NAND flash node instead.
This PIXIS node needs to remain enabled because it is used by platform code
to switch into indirect mode.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Here's the big driver core pull request for 3.6-rc1.
Unlike 3.5, this kernel should be a lot tamer, with the printk changes now
settled down. All we have here is some extcon driver updates, w1 driver
updates, a few printk cleanups that weren't needed for 3.5, but are good to
have now, and some other minor fixes/changes in the driver core.
All of these have been in the linux-next releases for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlARgIUACgkQMUfUDdst+ynDHgCfRNwIB9L+zZvjcKE5e1BhDbUl
wVUAn398DFgbJ1+PjGkd1EMR2uVTh7Ou
=MIFu
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core changes from Greg Kroah-Hartman:
"Here's the big driver core pull request for 3.6-rc1.
Unlike 3.5, this kernel should be a lot tamer, with the printk changes
now settled down. All we have here is some extcon driver updates, w1
driver updates, a few printk cleanups that weren't needed for 3.5, but
are good to have now, and some other minor fixes/changes in the driver
core.
All of these have been in the linux-next releases for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (38 commits)
printk: Export struct log size and member offsets through vmcoreinfo
Drivers: hv: Change the hex constant to a decimal constant
driver core: don't trigger uevent after failure
extcon: MAX77693: Add extcon-max77693 driver to support Maxim MAX77693 MUIC device
sysfs: fail dentry revalidation after namespace change fix
sysfs: fail dentry revalidation after namespace change
extcon: spelling of detach in function doc
extcon: arizona: Stop microphone detection if we give up on it
extcon: arizona: Update cable reporting calls and split headset
PM / Runtime: Do not increment device usage counts before probing
kmsg - do not flush partial lines when the console is busy
kmsg - export "continuation record" flag to /dev/kmsg
kmsg - avoid warning for CONFIG_PRINTK=n compilations
kmsg - properly print over-long continuation lines
driver-core: Use kobj_to_dev instead of re-implementing it
driver-core: Move kobj_to_dev from genhd.h to device.h
driver core: Move deferred devices to the end of dpm_list before probing
driver core: move uevent call to driver_register
driver core: fix shutdown races with probe/remove(v3)
Extcon: Arizona: Add driver for Wolfson Arizona class devices
...
The sram_offset parameter represents a physical address and should be of
type phys_addr_t. As part of this fix, the extraction of sram_params is
being cleaned-up and fixed.
This patch fixes now the case when the offset value of 0xfff00000 was being
rejected by the driver (returning -EINVAL), although this is a valid offset
value.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Here's the big staging tree merge for the 3.6-rc1 merge window.
There are some patches in here outside of drivers/staging/, notibly the iio
code (which is still stradeling the staging / not staging boundry), the pstore
code, and the tracing code. All of these have gotten ackes from the various
subsystem maintainers to be included in this tree. The pstore and tracing
patches are related, and are coming here as they replace one of the android
staging drivers.
Otherwise, the normal staging mess. Lots of cleanups and a few new drivers
(some iio drivers, and the large csr wireless driver abomination.)
Note, you will get a merge issue with the following files:
drivers/staging/comedi/drivers/s626.h
drivers/staging/gdm72xx/netlink_k.c
both of which should be trivial for you to handle.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlAQiD8ACgkQMUfUDdst+ykxhgCeMUjvc+1RTtSprzvkzpejgoUU
6A4AnAleWMnkaCD8vruGnRdGl/Qtz51+
=mN6M
-----END PGP SIGNATURE-----
Merge tag 'staging-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree patches from Greg Kroah-Hartman:
"Here's the big staging tree merge for the 3.6-rc1 merge window.
There are some patches in here outside of drivers/staging/, notibly
the iio code (which is still stradeling the staging / not staging
boundry), the pstore code, and the tracing code. All of these have
gotten acks from the various subsystem maintainers to be included in
this tree. The pstore and tracing patches are related, and are coming
here as they replace one of the android staging drivers.
Otherwise, the normal staging mess. Lots of cleanups and a few new
drivers (some iio drivers, and the large csr wireless driver
abomination.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up trivial conflicts in drivers/staging/comedi/drivers/s626.h and
drivers/staging/gdm72xx/netlink_k.c
* tag 'staging-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1108 commits)
staging: csr: delete a bunch of unused library functions
staging: csr: remove csr_utf16.c
staging: csr: remove csr_pmem.h
staging: csr: remove CsrPmemAlloc
staging: csr: remove CsrPmemFree()
staging: csr: remove CsrMemAllocDma()
staging: csr: remove CsrMemCalloc()
staging: csr: remove CsrMemAlloc()
staging: csr: remove CsrMemFree() and CsrMemFreeDma()
staging: csr: remove csr_util.h
staging: csr: remove CsrOffSetOf()
stating: csr: remove unneeded #includes in csr_util.c
staging: csr: make CsrUInt16ToHex static
staging: csr: remove CsrMemCpy()
staging: csr: remove CsrStrLen()
staging: csr: remove CsrVsnprintf()
staging: csr: remove CsrStrDup
staging: csr: remove CsrStrChr()
staging: csr: remove CsrStrNCmp
staging: csr: remove CsrStrCmp
...
The following build error occured during a ia64 build with
swap-over-NFS patches applied.
net/core/sock.c:274:36: error: initializer element is not constant
net/core/sock.c:274:36: error: (near initialization for 'memalloc_socks')
net/core/sock.c:274:36: error: initializer element is not constant
This is identical to a parisc build error. Fengguang Wu, Mel Gorman
and James Bottomley did all the legwork to track the root cause of
the problem. This fix and entire commit log is shamelessly copied
from them with one extra detail to change a dubious runtime use of
ATOMIC_INIT() to atomic_set() in drivers/char/mspec.c
Dave Anglin says:
> Here is the line in sock.i:
>
> struct static_key memalloc_socks = ((struct static_key) { .enabled =
> ((atomic_t) { (0) }) });
The above line contains two compound literals. It also uses a designated
initializer to initialize the field enabled. A compound literal is not a
constant expression.
The location of the above statement isn't fully clear, but if a compound
literal occurs outside the body of a function, the initializer list must
consist of constant expressions.
Cc: <stable@vger.kernel.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Set the max hw sectors in a namespace's request queue if the nvme device
has a max data transfer size.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Here's the big USB patch set for the 3.6-rc1 merge window.
Lots of little changes in here, primarily for gadget controllers and drivers.
There's some scsi changes that I think also went in through the scsi tree, but
they merge just fine. All of these patches have been in the linux-next tree
for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlAQhpcACgkQMUfUDdst+yms4wCgpMbfFYTZ8lHpDnXHYFv6qw8j
FIsAmwT4mbT7m8C0k+ELV/5T2e0eYJEQ
=QetG
-----END PGP SIGNATURE-----
Merge tag 'usb-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big USB patch set for the 3.6-rc1 merge window.
Lots of little changes in here, primarily for gadget controllers and
drivers. There's some scsi changes that I think also went in through
the scsi tree, but they merge just fine. All of these patches have
been in the linux-next tree for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up trivial conflicts in include/scsi/scsi_device.h (same libata
conflict that Jeff had already encountered)
* tag 'usb-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (207 commits)
usb: Add USB_QUIRK_RESET_RESUME for all Logitech UVC webcams
usb: Add quirk detection based on interface information
usb: s3c-hsotg: Add header file protection macros in s3c-hsotg.h
USB: ehci-s5p: Add vbus setup function to the s5p ehci glue layer
USB: add USB_VENDOR_AND_INTERFACE_INFO() macro
USB: notify phy when root hub port connect change
USB: remove 8 bytes of padding from usb_host_interface on 64 bit builds
USB: option: add ZTE MF821D
USB: sierra: QMI mode MC7710 moved to qcserial
USB: qcserial: adding Sierra Wireless devices
USB: qcserial: support generic Qualcomm serial ports
USB: qcserial: make probe more flexible
USB: qcserial: centralize probe exit path
USB: qcserial: consolidate usb_set_interface calls
USB: ehci-s5p: Add support for device tree
USB: ohci-exynos: Add support for device tree
USB: ehci-omap: fix compile failure(v1)
usb: host: tegra: pass correct pointer in ehci_setup()
USB: ehci-fsl: Update ifdef check to work on 64-bit ppc
USB: serial: keyspan: Removed unrequired parentheses.
...
* Updating libata to directly bind with ACPI / runtime power mgmt.
This is a pre-req for SATA ZPODD (CD-ROM power management).
Touches ACPI (exports++) and SCSI in minor ways. Has been in linux-next
for weeks.
The rest of this should come via SCSI tree, as it involves a lot of updates
to the 'sr' driver etc.
Other, minor changes:
* module_pci_driver() removes a lot of common boilerplate from each PCI driver
* minor coding style, whitespace cleanups
* pata_pcmcia bug fix, caught by Coccinelle
* pata_imx, sata_dwc_460ex minor vendor updates
* ahci_platform: use simple PM ops, and thereby add hibernation cb's
* Add a few device-specific quirks
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAUBBVaCWzCDIBeCsvAQI+5Q/8CuxFaimde21SkPkwopL+Ij3YikgO2h1D
hjRX/2HodFIswmyjOvitX7mgaa0ojjU06zR/YJM5e0KQvRJMZxHV0VjRzZQz8Sq7
ELoC7De4NLyz/2hFvwyshQuamaYI4145tS7oeQAF4o3SnOVwtDiQGuxK4aVaDlKt
nRu+VBZ2qGD7TsiSu6eKtP1v4QRjy/5jYWlxqQH2Hr81FeP6gO5OlHiCrnAKqBCh
QiXV/PG/GRr63mB4AHMn/G9rvtz3G16IgjcXHB+6jWnJOVUAwjbL5N4bSD6fP4w5
ecaL6V1UYLmsJQlSEVDayV1Kay1F7H478GKzCiiakZMlp9pu0u5dqJD+uBdzFy5W
EuemeBMSOV9wuAg4CosZKgjyxysR8Zs+eYabp1VCLK8Q4hlisporrCYJNGSGErXD
c3CZQ2RVLlbMFRYjqLATe0p4WJd8nBdxvnP6vJ6ua6ArJu7KQ8I/Of0+GRPsQO8i
sDaIz/ycuXskt+iWU15RA8Juzu8DyCwTf7RtriT1Nc03JcOk7tVkoGTBtbgo/PaB
fP5VLveF9KKxZzjPJLBqIVspMbfGSVzoNN5nJFPlIUg6cDdA+60DzgkJjP2vtTnn
px/tGykZAM1fTWCRckTvysRgpfTmcVomeppYsAQqjZ+wH2SOkcscYLEq3l10UMEi
Wjy6DdqFrlU=
=Ou1W
-----END PGP SIGNATURE-----
Merge tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata updates from Jeff Garzik:
"Notable changes:
- Updating libata to directly bind with ACPI / runtime power mgmt.
This is a pre-req for SATA ZPODD (CD-ROM power management).
Touches ACPI (exports++) and SCSI in minor ways. Has been in
linux-next for weeks.
The rest of this should come via SCSI tree, as it involves a lot of
updates to the 'sr' driver etc.
Other, minor changes:
- module_pci_driver() removes a lot of common boilerplate from each
PCI driver
- minor coding style, whitespace cleanups
- pata_pcmcia bug fix, caught by Coccinelle
- pata_imx, sata_dwc_460ex minor vendor updates
- ahci_platform: use simple PM ops, and thereby add hibernation cb's
- Add a few device-specific quirks"
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (23 commits)
[libata] pata_cmd64x: whitespace cleanup
libata-acpi: fix up for acpi_pm_device_sleep_state API
sata_dwc_460ex: device tree may specify dma_channel
ahci, trivial: fixed coding style issues related to braces
ahci_platform: add hibernation callbacks
libata-eh.c: local functions should not be exposed globally
libata-transport.c: local functions should not be exposed globally
sata_dwc_460ex: support hardreset
ata: use module_pci_driver
drivers/ata/pata_pcmcia.c: adjust suspicious bit operation
pata_imx: Convert to clk_prepare_enable/clk_disable_unprepare
ahci: Enable SB600 64bit DMA on MSI K9AGM2 (MS-7327) v2
[libata] Prevent interface errors with Seagate FreeAgent GoFlex
drivers/acpi/glue: revert accidental license-related 6b66d95895 bits
libata-acpi: add missing inlines in libata.h
libata: tell scsi layer device supports runtime power off
libata: detect Device Attention support
libata-acpi: register/unregister device to/from power resource
libata-acpi: add ata port runtime D3Cold support
libata-acpi: set acpi state for SATA port
...
The specification does not provide a use for command dword11 in the NVMe
Get Features command, but does use the NSID for some features.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
The function nvme_user_admin_command does not require a namespace to
proceed. Replace with the nvme_dev structure so that it can be called
from contexts that do not have a namespace.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
register_blkdev returns 0 when given a valid major number.
Reported-by:Ross Zwisler <ross.zwisler@intel.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
The generic HDMI code detaches the converter from the stream when
unused, but it must be done rather in the close callback instead of
the cleanup callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The downgrade of the 4 level page table created by init_new_context is
currently done only in start_thread31. If a 31 bit process forks the
new mm uses a 4 level page table, including the task size of 2<<42
that goes along with it. This is incorrect as now a 31 bit process
can map memory beyond 2GB. Define arch_dup_mmap to do the downgrade
after fork.
Cc: stable@vger.kernel.org
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move iop33x and iop32x PCI to fixed i/o mapping and remove io.h. This
changes the PCI bus addresses from the cpu address to 0 based. It appears
that there is translation h/w for this, but its untested.
Not sure what to do with io_offset. I think it should always be 0.
AFAICT, PCI setup is skipped if the ATU is already setup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Move mv78xx0 PCI to fixed i/o mapping and remove io.h. This changes the PCI
bus addresses from the cpu address to 0 based. It appears that there is
translation h/w for this, but its untested.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Move iop13xx PCI to fixed i/o mapping and remove io.h.
This changes the PCIe bus address to start at 0x10000. Let's hope this
works. If it does not, the alternative would be to revert the value we
write into OIOTVR to zero and set sys->io_offset to 64K.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
iop13xx confuses I/O port numbers with physical addresses, which breaks
legacy ISA I/O access behind PCI bridges and makes it unnecessarily hard
to unify the inb/outb accessors with other platforms. This removes the
special-casing and just puts all I/O ports into a single 128KB virtually
mapped I/O port range starting at port zero.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Move orion5x PCI to fixed i/o mapping and remove io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Move kirkwood PCI to fixed i/o mapping and remove io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
The i/o regions are changed from 1MB to 64KB. It's likely that the 2nd
bus is not setup correctly.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Move footbridge PCI to fixed i/o mapping. io.h is still needed for the
!MMU case.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Convert shark to use the fixed i/o mapping and remove io.h.
This shrinks the mapping from 256MB to 1MB, but nothing is using that much
space AFAICT.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Move tegra PCI to fixed i/o mapping and remove io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Colin Cross <ccross@android.com>
Cc: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
With consolidation of the PCI i/o mappings, the i/o space is being
set to start at a PCI bus addr of 0x0 and fixed to 64K per bus. In
this case the core ARM PCI setup code can setup the i/o resource.
Currently, the resource is only setup if the platform did not setup
an i/o resource.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Default CoreNet Coherency Bus (CCB) frequency on P3041 is 750MHz, but espi
cannot work at 40MHz with this CCB frequency, so we need to slow down the
clock rate of espi to 35MHz to make it work stable at the CCB frequency.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Typically, the return value desired for the failure of a
function with an integer return value is a negative integer. In
these cases, the return value is sometimes a negative integer
and sometimes 0, due to a subsequent initialization of the
return variable within the loop.
A simplified version of the semantic match that finds this
problem is: (http://coccinelle.lip6.fr/)
//<smpl>
@r exists@
identifier ret;
position p;
constant C;
expression e1,e3,e4;
statement S;
@@
ret = -C
... when != ret = e3
when any
if@p (...) S
... when any
if (\(ret != 0\|ret < 0\|ret > 0\) || ...) { ... return ...; }
... when != ret = e3
when any
*if@p (...)
{
... when != ret = e4
return ret;
}
//</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Link: http://lkml.kernel.org/r/1342284188-19176-7-git-send-email-Julia.Lawall@lip6.fr
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Sandy Bridge processors follow the SDM (Vol 3B, Table 15-20) and
set both the RIPV and EIPV bits in the MCG_STATUS register to
zero for machine checks during instruction fetch. This is more
than a little counter-intuitive and means that Linux cannot
recover from these errors. Rather than insert special case code
at several places in mce.c and mce-severity.c, we pretend the
EIPV bit was set for just this case early in processing the
machine check.
Acked-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Link: http://lkml.kernel.org/r/180a06f3f357cf9f78259ae443a082b14a29535b.1343078495.git.tony.luck@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We will need some of these values in mce.c. Move them to the
appropriate header file so they are available.
Acked-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Link: http://lkml.kernel.org/r/0ccfb1af5fe35e537b7cd8e4d448bf7d851dbfb9.1343078495.git.tony.luck@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When CONFIG_PERF_EVENTS disabled, there will have a compiliation
error, because missing struct before structure name.
Signed-off-by: Jovi Zhang <bookjovi@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jiri Kosina <trivial@kernel.org>
Link: http://lkml.kernel.org/r/CACV3sbKF%3DCX%2B2jWEWesfCA6rBoQ3wDM4-5ac9MuBtVbCtMRHdQ@mail.gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In the current kernel, percpu variable `vector_irq' is not always
cleared when a CPU is offlined. If the CPU that has the disabled
irqs in vector_irq is hotplugged again, __setup_vector_irq()
hits invalid irq vector and may crash.
This bug can be reproduced as following;
# echo 0 > /sys/devices/system/cpu/cpu7/online
# modprobe -r some_driver_using_interrupts # vector_irq@cpu7 uncleared
# echo 1 > /sys/devices/system/cpu/cpu7/online # kernel may crash
To fix this problem, this patch clears vector_irq in
__fixup_irqs() when the CPU is offlined.
This also reverts commit f6175f5bfb, which partially fixes
this bug by clearing vector in __clear_irq_vector(). But in
environments with IOMMU IRQ remapper, it could fail because
cfg->domain doesn't contain offlined CPUs. With this patch, the
fix in __clear_irq_vector() can be reverted because every
vector_irq is already cleared in __fixup_irqs() on offlined CPUs.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama.qu@hitachi.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: yrl.pp-manager.tt@hitachi.com
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Alexander Gordeev <agordeev@redhat.com>
Link: http://lkml.kernel.org/r/20120726104732.2889.19144.stgit@kvmdev
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The make target 'oldnoconfig' is a misnomer. It doesn't set new symbols
to 'n', but instead sets it to their default values.
Unfortunately, assuming that it actually did this, broke ktest in some
of its tests. For example, the tests to create a minimum config and even
a config bisect, depends on removing various configs and using
oldnoconfig to get rid of other configs that may have depended on it.
But because some configs that it was trying to disable, were in fact
default enabled, this caused those configs to re-enable and corrupt the
test.
I thought about fixing oldnoconfig, but I'm afraid that people are
already dependent on its current behavior. Instead, I'm just updating
the documentation to state that it sets the new symbols to their default
values and not to 'n'.
Ideally, this would be called, 'olddefconfig' and we have an
'oldnoconfig' that actually disables the new symbols. But it's useless
for me now. If it changed, ktest would need to be consistent between
each version, and that would be to difficult to detect. I'll handle this
issue with ktest with other means.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
As we use a macro trick to sync each error codes with its
description string, teach [ce]tags to process them properly.
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/n/tip-qt5fv4pzigr2nnl27ydimg4h@git.kernel.org
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Thought to be another merge error, board-mop500-msp.h has never existed
in the upstream kernel, only msp.h. This patch changes the include files
to match the existing file name.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We believe to have squashed all issues around the gen6+ rps interrupt
generation and why the gpu sometimes got stuck. With that cleared up,
there's no user left for the sanitize_pm infrastructure, so let's just
rip it out.
Note that 'intel_reg_write 0xa014 0x13070000' is the w/a if we find
ourselves stuck again.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The power docs say that when the gt leaves rc6, it is in the lowest
frequency and only about 25 usec later will switch to the frequency
selected in GEN6_RPNSWREQ. If the downclock limit expires in that
window and the down limit is set to the lowest possible frequency, the
hw will not send the down interrupt. Which leads to a too high gpu
clock and wasted power.
Chris Wilson already worked on this with
commit 7b9e0ae6da
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sat Apr 28 08:56:39 2012 +0100
drm/i915: Always update RPS interrupts thresholds along with
frequency
but got the logic inverted: The current code set the down limit as
long as we haven't reached it. Instead of only once with reached the
lowest frequency.
Note that we can't always set the downclock limit to 0, because
otherwise the hw will keep on bugging us with downclock request irqs
once the lowest level is reached.
For similar reasons also always set the upclock limit, otherwise the
hw might poke us again with interrupts.
v2: Chris Wilson noticed that the limit reg is also computed in
sanitize_pm. To avoid duplication, extract the code into a common
function.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Introduce a new trace system, kvm-s390, for some kvm/s390 specific
trace points:
- injection of interrupts
- delivery of interrupts to the guest
- creation/destruction of kvm machines and vcpus
- stop actions for vcpus
- reset requests for userspace
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Add trace events for several s390 architecture specifics:
- SIE entry/exit
- common intercepts
- common instructions (sigp/diagnose)
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Provide a new function, insn_to_mnemonic, by which e.g. kvm can obtain
a human-readable decoding of an instruction's opcode.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
By selecting the cache level (essentially whether or not the CPU snoops
any updates to the bo, and on more recent machines whether it resides
inside the CPU's last-level-cache) a userspace driver is able to then
manage all of its memory within buffer objects, if it so desires. This
enables the userspace driver to accelerate uploads and more importantly
downloads from the GPU and to able to mix CPU and GPU rendering/activity
efficiently.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Added code comment about where we plan to stuff platform
specific cacheing control bits in the ioctl struct.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Several functions of the GPU have the restriction that differing memory
domains cannot be placed next to each other (as the GPU may prefetch
beyond the end of one domain and hang as it crosses into the other
domain). We use the facility of the drm_mm to mark ranges with a
particular color that corresponds to the cache attributes of those pages
in order to prevent allocating adjacent blocks of differing memory
types.
v2: Rebase ontop of drm_mm coloring v2.
v3: Fix rebinding existing gtt_space and add a verification routine.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The event control register of SNB-EP uncore QPI box has a one bit
extension at bit position 21.
Reported-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1343097850-4348-1-git-send-email-zheng.z.yan@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
LLC-* and node-* events require using the OFFCORE_RESPONSE events
on SandyBridge, but the hw_cache_extra_regs is left uninitialized.
This patch adds the missing extra register configure table for
SandyBridge.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1342517275-2875-1-git-send-email-zheng.z.yan@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
