Setting the fifo to only 1 byte generates one interrupt every 1ms at 9600 bauds.
This is too much. This patch reduces the threshold to speeds below 2400 bauds
like in the 8250 UART driver.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a desynchronisation problem with CPM UART driver on
Powerpc MPC8xx. The problem happens if data is received before the device
is open by the user application.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apparently the same card model has two IDs, so this patch
complements the commit 39aced68d6
adding the missing one.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch does the following
- In case of errors if there least one data character in the RX FIFO
read it otherwise it may stall the receiver.
This is recommended in the interrupt reset method in the table 23-246 of
the omap4 TRM.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds driver for Samsung S5K4ECGX image sensor with an
embedded SoC ISP. The driver only implements preview operation mode
and still capture (snapshot) and face detection features are missing
now. Following controls are supported: contrast, saturation,
brightness, sharpness.
Signed-off-by: Sangwook Lee <sangwook.lee@linaro.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The legacy serial driver will detect the Winbond CIR device as a serial
port, since it looks exactly like a serial port unless you know what
it is from the PNP ID.
Here we track this port as a special PORT_8250_CIR type, preventing the
legacy serial driver from probing it.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We first probe the legacy serial ports and then check pnp. If there
is a non-standard configuration then this might not work, also this
change is needed so we can blacklist Winbond CIR based on PNP ID.
For this to work the 8250_pnp driver must be merged into the 8250
module.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New mem-to-mem video drivers should use V4L2_CAP_VIDEO_M2M capability, rather
than ORed V4L2_CAP_VIDEO_CAPTURE and V4L2_CAP_VIDEO_OUTPUT flags, as outlined
in commit a1367f1b26.
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix some minor problems in comments of lis331dlh driver
* correct comments with respect to 2G sensitivity
* correct typo lis3331dlh mistake to lis331dlh
* add comment to say only 2G range is supported
* change the function name from lis3lv02d_read_16 to
lis331dlh_read_data.
* update i2c_device_id table entry to maintaine consistancy
* update sensor display message
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
channel_first_int[][] variable is used as a flag for the ISR,
This flag was being set after enabling the interrupts, There
where situations when the isr occurred even before the flag was set
dues to which it was causing the application hang.
This patch sets channel_first_int[][] flag just before enabling the
interrupt.
Reported-by: David Oleszkiewicz <doleszki@adsyscontrols.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pci_disable_device(pdev) used to be in pci remove function. But this
PCI device has two functions with interrupt lines connected to a
single pin. The other one is a USB host controller. So when we disable
the PIN there e.g. by rmmod hpilo, the controller stops working. It is
because the interrupt link is disabled in ACPI since it is not
refcounted yet. See acpi_pci_link_free_irq called from
acpi_pci_irq_disable.
It is not the best solution whatsoever, but as a workaround until the
ACPI irq link refcounting is sorted out this should fix the reported
errors.
References: https://lkml.org/lkml/2008/11/4/535
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Nobin Mathew <nobin.mathew@gmail.com>
Cc: Robert Hancock <hancockr@shaw.ca>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Altobelli <david.altobelli@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_port_tty_get() can return NULL after port hangup that may happen anytime.
The patch adds checks that tty_port_tty_get() returns nonNULL around places
where tty is actually used.
I have no actual hardware to test the patch, so I have updated rx side
processing from common sense only.
v2: rx handling updated according Alan Cox feedback.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove useless kfree() and clean up code related to the removal.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
position p1,p2;
expression x;
@@
if (x@p1 == NULL) { ... kfree@p2(x); ... return ...; }
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes some translation error in Documentation/zh_CN/gpio.txt
The modification is based on Dong Aisheng <b29396@freescale.com>'s
corrections:
1.Two "OUTPUT" is incorrectly translated as "输入";
2.five improvement of translation;
3.Delete a redundant paragraph,
Signed-off-by: Fu Wei <tekkamanninja@gmail.com>
Acked-by: Harry Wei <harryxiyou@gmail.com>
Acked-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove 3 byte redundant code at the head of
the Documentation/zh_CN/arm/booting
When I see the file Documentation/zh_CN/arm/booting using
Bless(binary Viewer),I find 3 byte redundant in it. So I
make a patch to correcting that error made by me.
Signed-off-by: Fu Wei <tekkamanninja@gmail.com>
Acked-by: Harry Wei <harryxiyou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a Chinese translated version of Documentation/video4linux/omap3isp.txt
Signed-off-by: Fu Wei <tekkamanninja@gmail.com>
Acked-by: Harry Wei <harryxiyou@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some post-3.4 kernels have a problem when a cloned skb is used in the
RX path. This patch handles one such case for r8712u.
The patch was suggested by Eric Dumazet.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [v3.4+]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a failure in vb2_qbuf in user pointer mode where
__qbuf_userptr checks if the buffer queued by userspace is large
enough. The failure would happen if coda_queue_setup was called
with empty fmt (and thus set the expected buffer size to the maximum
resolution), and userspace queues buffers of smaller size -
corresponding to the negotiated dimensions - were queued.
Explicitly setting sizeimage to the value negotiated via s_fmt
fixes the issue.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The hardware can also rotate in 90° steps, but there is no
corresponding V4L2_CID defined yet.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While the CODA is running a PIC_RUN command, its registers are
not to be touched.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
USERPTR buffer support is provided by the videobuf2 framework.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a 1 second timeout for each PIC_RUN command to the CODA. In
case it locks up, stop all queues and dequeue remaining buffers.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Determining the next free instance just by incrementing and decrementing
an instance counter does not work: if there are two instances opened,
0 and 1, and instance 0 is released, the next call to coda_open will
create a new instance with index 1, but instance 1 is already in use.
Instead, scan a bitfield of active instances to determine the first
free instance index.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
job_ready is supposed to signal whether a context is ready to be
added to the job queue, not whether the CODA is ready to run it
immediately.
Calling v4l2_m2m_job_finish at the end of coda_irq_handler already
guarantees that the coda is ready when v4l2-mem2mem eventually tries
to run the next queued job.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some codecs running on CODA need internal framebuffers for reference and
reconstructed frames. Allocate them separately, and do not use the input
vb2_buffers: those will be handed off to userspace regularly, and there
is no way to signal to the CODA which of the registered framebuffers are
off limits. As a consequence, userspace is now free to choose the number
of v4l2 buffers.
This patch also includes the code to set up the parameter buffer for
CODA7 and above with 64-bit AXI bus width.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Javier Martin <javier.martin@vista-silicon.com>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This uses the ARCH_MXC specific iram_alloc API to allocate a work
buffer in the SoC's on-chip SRAM and sets up the AXI_SRAM_USE
register. In the future, the allocation will be converted to use
the genalloc API.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit d97b46a64 ("syscalls, x86: add __NR_kcmp syscall" ) added a new
syscall to support checkpoint restore. It is currently x86-only, but
that restriction will be removed in a subsequent patch. Unfortunately,
the kernel checksyscalls script had a bug which suppressed any warning
to other architectures that the kcmp syscall was not implemented. A
patch to checksyscalls is being tested in linux-next and other
architectures are seeing warnings about kcmp being unimplemented.
This patch adds __NR_kcmp to <asm-generic/unistd.h> so that kcmp is
wired in for architectures using the generic syscall list.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Add support for loading a raw firmware with 16-bit chars ordered in
little-endian 64-bit words, corresponding to the memory access pattern
of CODA7 and above: When writing the boot code into the code download
register, the chars have to be reordered back.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
New mem-to-mem video drivers should use V4L2_CAP_VIDEO_M2M capability, rather
than ORed V4L2_CAP_VIDEO_CAPTURE and V4L2_CAP_VIDEO_OUTPUT flags, as outlined
in commit a1367f1b26.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ELSE IF statements do not work as expected if another ELSE statement
follows. This is because the $if_set is not set. If the ELSE IF
condition is true, the following ELSE should be ignored. But because the
$if_set is not set, the following ELSE will also be executed.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Check against q->fileio to see if the queue owner should be set or not.
The former check against the return value of read or write is wrong, since
read/write can return an error, even if the queue is in streaming mode.
For example, EAGAIN when in non-blocking mode.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The third output on WM5110 is a general purpose headphone output which can
be used to drive an earpice rather than a dedicated earpiece driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To apply a filter to all the evsels in an evlist.
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-v9x3q9rv4caxtox7wtjpchq5@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
One more patch for this thing, fixing some typos in the documentation.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
ERRnoresource is an ERRSRV level (aka server-side) error and means "No
resources currently available for request". Currently that maps to POSIX
-ENOBUFS. No NT errors map to it currently.
NT_STATUS_INSUFFICIENT_RESOURCES and NT_STATUS_INSUFF_SERVER_RESOURCES
are also similar in meaning. Currently the client maps those to
ERRnomem, which maps to -ENOMEM in POSIX.
All of these mappings seem to be quite wrong to me and are confusing for
users. All of the above errors indicate problems on the server, not the
client. Reporting -ENOMEM or -ENOBUFS implies that the client is running
out of resources.
This patch changes those mappings. The NT_* errors are changed to map to
the SRV level ERRnoresource. That error is in turn changed to return
-EREMOTEIO which is the only POSIX error I could find that conveys that
something went wrong on the server. While we're at it, change the SMB2
equivalent error to return the same.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Acked-by: Suresh Jayaraman <sjayaraman@suse.com>
Signed-off-by: Steve French <smfrench@gmail.com>
This makes it easier to read and also ties in more closely with the
profile concept.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
`ni_ai_poll()` currently acquires (and later releases) the comedi
device's spin-lock iff `in_interrupt()` returns 0. However, it is only
called during processing of a `COMEDI_POLL` ioctl so `in_interrupt()`
will always return 0 in this case. Remove this test and acquire/release
the spin-lock unconditionally. This eliminates a sparse warning about
different lock contexts for basic block.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`s626_enc_insn_config()` is the `insn_config()` handler for a counter
subdevice. The `data[0]` value is supposed to be one of the
`INSN_CONFIG_...` constants defined in "comedi.h" indicating the type of
configuration instruction, but this function seems to be using it as a
variable value to preload the counter with. Various values of `data[0]`
are going to cause `check_insn_config_length()` in the comedi core
("comedi_fops.c") to return an error, and this function won't be called
in those cases. Most other values will log a warning to the kernel log.
It's not entirely clear what constant should be checked for in
`data[0]`, so add a "FIXME" comment for now.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
