Add a new SoC data structure for Tegra238 platforms and register the
nvidia,tegra238-sdhci compatible string. Configure the supported
features and tap delay values for the Tegra238 SDHCI controller.
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Add the compatible string for the SDHCI block found on the Tegra238 SoC.
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Replace irq_of_parse_and_map() with platform_get_irq_optional() to
get the wake IRQ. This is a more portable approach that works with
both DT and non-DT platforms, and follows the modern platform API
conventions for optional IRQ resources.
The wake IRQ is now fetched earlier in the probe function alongside
the main IRQ, and the -EPROBE_DEFER case is handled properly before
the deferred probe can be triggered.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Disabling the device interrupt and freeing the IRQ prevents new card-detect
work from being queued, but carddet_work already queued by the handler can
still run after via_sd_remove() returns. via_sdc_card_detect() recovers the
host through container_of() and dereferences its MMIO base; once remove()
returns the host can be freed, so that work would touch freed memory.
Cancel carddet_work after freeing the IRQ and before cancelling
finish_bh_work, which the card-detect handler can also queue. carddet_work
can re-enable the interrupt through via_reset_pcictrl(); mask it again
afterwards.
This issue was found by an in-house static analysis tool and confirmed by
manual code review.
Fixes: f0bf7f61b8 ("mmc: Add new via-sdmmc host controller driver")
Cc: stable@vger.kernel.org
Assisted-by: Codex:gpt-5.6
Signed-off-by: Fan Wu <fanwu01@zju.edu.cn>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
request_irq() registers the SD card-detect interrupt and the probe enables
it before mmc_add_host() runs. If mmc_add_host() fails, the error path only
unmaps the registers and returns: the interrupt stays registered, so the
handler keeps running against the host once it is freed. via_sdc_isr()
dereferences sdhost and its MMIO base and schedules carddet_work, which
via_sdc_card_detect() also runs against freed memory through its
container_of() dereference.
Add a probe-error path that disables and frees the interrupt and cancels
carddet_work before unmapping. carddet_work can re-enable the device
interrupt via via_reset_pcictrl(), which restores PCIINTCTRL, so mask it
again after cancelling the work.
This issue was found by an in-house static analysis tool and confirmed by
manual code review.
Fixes: e4e46fb61e ("mmc: via-sdmmc: fix return value check of mmc_add_host()")
Cc: stable@vger.kernel.org
Assisted-by: Codex:gpt-5.6
Signed-off-by: Fan Wu <fanwu01@zju.edu.cn>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Replace of_address_to_resource() and the following devm_ioremap_resource()
with a single devm_platform_get_and_ioremap_resource() call in
moxart_probe(). This requests the register region and maps it once, which
is equivalent to the previous devm_ioremap_resource() behavior, and drops
the now-redundant separate resource lookup.
Similarly replace irq_of_parse_and_map() with platform_get_irq(), which
returns a negative errno on failure (including -EPROBE_DEFER) instead of
0, and tighten the error check to irq < 0.
Both substitutions are equivalent for a DT-backed platform device. The
remaining OF usage (mmc_of_parse() and the of_device_id table) is covered
by already-included headers, so linux/of_address.h and linux/of_irq.h
are dropped.
No functional change; the MMC register window is requested and mapped
exactly once, so there is no overlapping region claim.
Built for ARM (allmodconfig + CONFIG_MMC_MOXART) with LLVM=1;
drivers/mmc/host/moxart-mmc.o compiles cleanly.
Assisted-by: opencode:hy3-free
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Since commit 55b48e23f5 ("genirq/devres: Add error handling in
devm_request_*_irq()"), devm_request_irq() and devm_request_threaded_irq()
automatically log detailed error messages on failure. Remove the
now-redundant driver-specific dev_err() and dev_err_probe() calls.
Signed-off-by: Pan Chuang <panchuang@vivo.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
As pointed out by sashiko bot in [0], recent proposed changes to
dma_max_mapping_size() may affect the driver.
While the issue reported may be a false positive, Robin pointed out some
other DMA-related issues in the driver which are addressed here:
- the DMA max mapping size is irrelevant for the programmed IO mode of
operation
- we should not call dma_max_mapping_size() on the MMC host platform
device, but rather the DMA engine device
In addition, it's better to use the device returned from
dmaengine_get_dma_device() for dma_umap_sg() and dma_unmap_sg(), and not
reference the DMA channel device directly.
[0] https://lore.kernel.org/linux-scsi/d82926fe-4557-401d-ae58-4302fef5657c@oracle.com/#t
Signed-off-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Merge the mmc fixes for v7.2-rc[n] into the next branch, to allow them to
get tested together with the mmc changes that are targeted for the next
release.
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
The dw_mci_pmops is exported out of dw_mmc.c so move the declaration of
ton dw_mmc.h from dw_mmc-pltfm.h to fix the following sparse warning:
drivers/mmc/host/dw_mmc.c:3512:25: warning: symbol 'dw_mci_pmops' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Check pm_runtime_force_resume() return value in resume. If it fails
(clock enable failure), return immediately since accessing hardware
registers on an unclocked device would cause a kernel panic.
The early return intentionally skips enable_irq() and
sdhci_disable_irq_wakeups() because the IRQ handler reads
SDHCI_INT_STATUS, which would also fault without clocks. The PM runtime
usage counter leak only affects this already-broken device instance and
is an acceptable tradeoff to preserve system stability.
Remove the return value check for mmc_gpio_set_cd_wake(host->mmc, false)
since disable_irq_wake() called internally always returns 0.
Also return 0 explicitly on the success path instead of propagating
stale return values.
Fixes: 676a838556 ("mmc: host: sdhci-esdhc-imx: refactor the system PM logic")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Make pinctrl_pm_select_sleep_state() and mmc_gpio_set_cd_wake() failures
non-fatal in the suspend path. These failures only mean slightly higher
power consumption or missing CD wakeup capability, but should not block
system suspend.
Also change the function to always return 0 on the success path instead
of propagating non-fatal warning return values.
Fixes: 676a838556 ("mmc: host: sdhci-esdhc-imx: refactor the system PM logic")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Replace pm_runtime_get_sync() with pm_runtime_resume_and_get() to
simplify error handling. pm_runtime_resume_and_get() automatically
drops the usage counter on failure, avoiding the need for a separate
pm_runtime_put_noidle() call. If it fails, the device is unclocked and
accessing hardware registers would cause a kernel panic, so return the
error immediately.
Fixes: 676a838556 ("mmc: host: sdhci-esdhc-imx: refactor the system PM logic")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
When using WIFI out-of-band wakeup, an "irq xxx: nobody cared" warning
occurs. This happens because the usdhc interrupt is not disabled during
system suspend when device_may_wakeup() returns false.
The sequence of events leading to this issue:
1. System enters suspend without disabling usdhc interrupt
(because device_may_wakeup() returns false for usdhc device)
2. WIFI out-of-band wakeup triggers system resume via GPIO interrupt
3. WIFI sends a Card interrupt before usdhc has fully resumed
4. usdhc is still in runtime suspend state and cannot handle the
interrupt properly
5. The unhandled interrupt triggers "nobody cared" warning
Fix this by unconditionally disabling the usdhc interrupt during suspend
and re-enabling it during resume, regardless of the wakeup capability.
This ensures no interrupts are processed during the suspend/resume
transition.
Fixes: 676a838556 ("mmc: host: sdhci-esdhc-imx: refactor the system PM logic")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
SDIO devices such as WiFi may keep power during suspend, so the MMC
core skips full card re-initialization on resume and directly restores
the host controller's ios timing to match the card. For DDR mode,
pm_runtime_force_resume() sets DDR_EN before the pin configuration is
restored from sleep state.
This is related to the SoC IP integration: switching pinctrl setting
(changing alt from GPIO to USDHC) impacts the internal loopback path.
If pinctrl configures the pad to GPIO function, once DDR_EN is set, the
DLL delay will be fixed based on the GPIO function loopback path. When
the pinctrl is later changed to USDHC function, the internal loopback
path changes, making the original fixed sample point no longer suitable
for the current loopback path. This causes persistent read CRC errors on
subsequent data transfers.
SD/eMMC running in DDR mode are unaffected as they are fully
re-initialized from legacy timing after resume.
Fix this by restoring the pinctrl state based on current timing mode
using esdhc_change_pinstate() before pm_runtime_force_resume(). This
ensures the correct pin configuration (e.g., 100/200MHz for UHS modes)
is applied before DDR_EN is set. Only restore for non-wakeup devices
since wakeup devices kept their active pin state during suspend.
Fixes: 676a838556 ("mmc: host: sdhci-esdhc-imx: refactor the system PM logic")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
esdhc_change_pinstate() checks for pins_100mhz and pins_200mhz at the
top of the function and returns -EINVAL if either is not defined. This
prevents the default case from ever being reached, which means devices
with a sleep pinctrl state but without high-speed pin states (100mhz/
200mhz) can never restore their default pin configuration.
Move the IS_ERR checks for pins_100mhz and pins_200mhz into their
respective switch cases.
Fixes: 676a838556 ("mmc: host: sdhci-esdhc-imx: refactor the system PM logic")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
sdhci_esdhc_imx_hwinit() unconditionally clears ESDHC_DLL_CTRL by
writing zero. For SDIO devices that keep power during system suspend
and operate in DDR mode, the card remains in DDR timing while the host
DLL override configuration is lost.
Extract the DLL override setup from esdhc_set_uhs_signaling() into
a helper esdhc_set_dll_override(), and call it on the resume path
when the card kept power and is using a DDR timing mode.
Fixes: 676a838556 ("mmc: host: sdhci-esdhc-imx: refactor the system PM logic")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
The tuning save/restore during system PM is conditioned on
mmc_card_wake_sdio_irq(), but this check is unrelated to whether
tuning values need to be preserved. The actual requirement is that
the card keeps power during suspend and the controller is a uSDHC.
SDIO devices using out-of-band GPIO wakeup maintain power during
suspend but do not set the SDIO IRQ wake flag. In this case the
tuning delay values are not saved/restored.
Remove the unnecessary mmc_card_wake_sdio_irq() condition from both
the suspend save and resume restore paths.
Fixes: c63d25cdc5 ("mmc: sdhci-esdhc-imx: Save tuning value when card stays powered in suspend")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Add the compatible for the MMC controllers of the Rockchip RV1106,
which are compatible with the RK3288 variant.
Unlike the newer controller in the RV1103B, which uses the RK3576
fallback, the RV1106 controller is the older IP whose drive and sample
phases are set through clocks provided by the GRF, so the RK3288
fallback is the correct one here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Some Realtek USB SD readers with a tray keep raw SD_CD asserted
when an empty tray is inserted. The MMC core then repeatedly tries to
initialize non-existent media, sees command timeouts, calls ->get_cd()
again, and starts the same detect cycle over.
Do not qualify media by open-coding MMC commands in ->get_cd().
Instead, let the normal MMC rescan path probe the card. If an
initialization command times out before a card has been attached,
suppress the raw SD_CD signal so the host can settle and the USB
parent can autosuspend.
Clear the suppression only when raw SD_CD drops. On the affected tray
reader, changing media requires removing and reinserting the tray, so
a low CD transition is the signal that a new insertion attempt can be
trusted again.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
The runtime autosuspend callback currently queries card status and
clears OCP by issuing USB register accesses. This can run from the
USB runtime-PM path itself, which is the wrong place to start more
device I/O.
Keep a cached copy of the card-status bits from normal status reads
instead. During runtime autosuspend, use that cached value only to
preserve the existing Memory Stick autosuspend deferral.
Do not treat raw SD_CD as an autosuspend blocker, because tray-based
SD readers can assert SD_CD with an empty tray. A real SD card is
protected by the SD/MMC child runtime-PM usage once powered.
Also stop clearing OCP from the runtime autosuspend callback, so the
callback does not issue USB commands.
Fixes: bb400d2120 ("mfd: rtsx_usb: Defer autosuspend while card exists")
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Log when the BlueField-3 eMMC hardware reset path is invoked.
This makes it easier to diagnose cases where the controller recovery path
depends on issuing an eMMC reset, and helps confirm that the reset sequence
was attempted on affected systems.
Signed-off-by: Satyansh Shukla <satyansh.shukla@oracle.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
The mmcblk.perdev_minors module parameter is parsed as a signed int and
is used during mmc_blk_init() to compute the number of supported block
devices.
Passing perdev_minors=0 makes the init path divide by zero when it
computes max_devices. Negative values are invalid as well and would make
max_devices negative before it is later used as an IDA limit.
Reject non-positive perdev_minors values before registering any mmcblk
resources.
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Merge the mmc fixes for v7.2-rc[n] into the next branch, to allow them to
get tested together with the mmc changes that are targeted for the next
release.
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Since commit 7852028a35 ("mmc: block: register RPMB partition with
the RPMB subsystem"), each mmc RPMB partition is represented by two
device objects:
- the mmc-owned device (`rpmb->dev`, backing the legacy /dev/mmcblkXrpmb
char device) and
- the rpmb-core device (`rdev`, backing /dev/rpmbN).
The child RPMB device holds a reference to its parent, so the
parent's release callback cannot be invoked if the child device
is still registered.
Remove rpmb_dev_unregister() from the parent release handler and
unregister the child RPMB device in the remove path before tearing
down the parent device.
Also delete the extra blank line between mmc_blk_remove_rpmb_part()
and {.
Fixes: 7852028a35 ("mmc: block: register RPMB partition with the RPMB subsystem")
Cc: stable@vger.kernel.org
Signed-off-by: Jiazi Li <jiazi.li@transsion.com>
Signed-off-by: Ao Sun <ao.sun@transsion.com>
Reviewed-by: Avri Altman <avri.altman@sandisk.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
The driver has an OF match table wired to .of_match_table, but does
not export the table with MODULE_DEVICE_TABLE().
Add the missing MODULE_DEVICE_TABLE(of, ...) entry so module alias
information is generated for OF based module autoloading.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
msb_ftl_initialize() computes the zone count from the card block count
with no bound:
msb->zone_count = msb->block_count / MS_BLOCKS_IN_ZONE;
...
for (i = 0; i < msb->zone_count; i++)
msb->free_block_count[i] = MS_BLOCKS_IN_ZONE;
msb->block_count is a card value. msb_read_boot_blocks() reads
number_of_blocks from the card boot page and byte swaps it.
free_block_count is a fixed int[MS_MAX_ZONES]. MS_MAX_ZONES is 16, so the
valid indices are 0 to 15. The init loop above indexes it by zone_count.
msb_mark_block_used() and msb_mark_block_unused() index it by
pba / MS_BLOCKS_IN_ZONE, for pba up to block_count - 1. A card may report
up to 65535 blocks. A block_count above 8192 (MS_MAX_ZONES *
MS_BLOCKS_IN_ZONE) lets the pba index reach 16. That writes past
free_block_count[] and corrupts struct msb_data. A larger count runs the
init loop past the end too.
A real Memory Stick has at most 16 zones. So it has at most 8192 blocks.
msb_ftl_initialize() now rejects a card that reports more than
MS_MAX_ZONES * MS_BLOCKS_IN_ZONE blocks.
Fixes: 0ab30494bc ("memstick: add support for legacy memorysticks")
Cc: stable@vger.kernel.org
Signed-off-by: Maoyi Xie <maoyixie.tju@gmail.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
MT8189 SoC MMC Controller IP has 4 additional clocks.
Describe them in the dt-bindings for this SoC.
Fixes: 7514f64780 ("dt-bindings: mmc: mtk-sd: Add support for MT8189 SoC")
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Convert STMicroelectronics sdhci-st MMC/SD controller binding from
text format to YAML DT schema.
Changes during conversion:
- Preserve optional 'icn' clock and 'top-mmc-delay' register region
via minItems: 1 on their respective properties.
- Conditionally require reg-names when two reg entries are present
via an allOf if/then block, preventing silent runtime failure in
devm_platform_ioremap_resource_byname().
- Constrain max-frequency to enum [200000000, 100000000, 50000000]
with a default of 50000000, matching the driver's behaviour in
sdhci-st.c.
Signed-off-by: Charan Pedumuru <charan.pedumuru@gmail.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Rename sdhci@9060000 and sdhci@9080000 nodes to mmc@9060000 and
mmc@9080000 in stih407-family.dtsi and update all derived board files
atomically to prevent orphaned node overrides.
Signed-off-by: Charan Pedumuru <charan.pedumuru@gmail.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
As the set_ios() function in litex_mmc driver does support
setting bus width, it is not necessary to leave the logic
for fixed bus width. Clean up these unneeded code.
Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Previously, the litex_mmc driver force the 4 bits bus width.
This means that the gateware with 1 bit bus width is not fit.
However, litesdcard does support setting bus width, which
make the 1 bit bus width gateware possible to be used.
Add logic for setting bus width in the set_ios() function.
Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Convert the Texas Instruments MMC host controller bindings
to DT schema.
Note that the OMAP2420 driver will not work with OMAP2430 or later omaps.
Please see the OMAP HSMMC driver for current OMAPs.
Signed-off-by: Eduard Bostina <egbostina@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Fix two places where the wrong type or conversion of little-endian
types to fix the following sparse warnings:
drivers/mmc/host/cqhci-core.c:487:15: warning: incorrect type in assignment (different base types)
drivers/mmc/host/cqhci-core.c:487:15: expected restricted __le32 [usertype]
drivers/mmc/host/cqhci-core.c:487:15: got int
drivers/mmc/host/cqhci-core.c:566:19: warning: incorrect type in assignment (different base types)
drivers/mmc/host/cqhci-core.c:566:19: expected unsigned long long [usertype] *task_desc
drivers/mmc/host/cqhci-core.c:566:19: got restricted __le64 [usertype] *
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Since actively working on TI AM654 SDHCI driver, adding myself
as a maintainer of this driver.
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
vub300_cmndwork_thread() holds cmd_mutex while it sends a command and
waits for the command response. If the response wait times out,
__vub300_command_response() kills the command URBs and then synchronously
resets the USB device through usb_reset_device().
That reset path re-enters the driver through vub300_pre_reset(), which
also takes cmd_mutex. The worker therefore tries to acquire the same
mutex recursively while it is still holding it from the command path.
This issue was found by our static analysis tool and then manually
reviewed against the current tree.
The grounded PoC kept the real worker and timeout/reset carrier:
vub300_cmndwork_thread()
__vub300_command_response()
usb_lock_device_for_reset()
usb_reset_device()
vub300_pre_reset()
Lockdep reported the same-task recursive acquisition on cmd_mutex:
WARNING: possible recursive locking detected
... (&test_vub300.cmd_mutex) ... at: usb_reset_device... [vuln_msv]
... (&test_vub300.cmd_mutex) ... at: vub300_cmndwork_thread+0x12/0x20 [vuln_msv]
Workqueue: vub300_cmd_wq vub300_cmndwork_thread [vuln_msv]
*** DEADLOCK ***
Return a flag from __vub300_command_response() when the timeout path needs
a device reset, then perform the reset after vub300_cmndwork_thread() has
cleared the in-flight command state and dropped cmd_mutex. The reset is
still attempted before mmc_request_done(), preserving the existing request
completion ordering while avoiding the recursive lock.
Fixes: 88095e7b47 ("mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver")
Cc: stable@vger.kernel.org
Signed-off-by: Runyu Xiao <runyu.xiao@seu.edu.cn>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
moxart_transfer_dma() waits for the DMA completion but ignores
wait_for_completion_interruptible_timeout(). It then unconditionally
reports the full transfer length in data->bytes_xfered.
Terminate the DMA channel and set data->error when the wait is
interrupted or times out. Only report host->data_len as transferred
after the completion is observed.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
The vub300 driver lifetime-manages its controller state using
vub300->kref, with vub300_delete() freeing the mmc host when the last
reference is dropped. The probe error path after the inactivity timer has
been armed still bypasses that lifetime rule, however, and falls through
to mmc_free_host() directly if mmc_add_host() fails.
The race window is between arming the inactivity timer and reaching the
probe error unwind after mmc_add_host() fails:
probe thread timer/workqueue
------------ ---------------
kref_init(&vub300->kref) ref = 1
kref_get(&vub300->kref) ref = 2, timer ref
add_timer(inactivity_timer) fires after one second
|
| race window
|<---------------------------------------------------->
|
mmc_add_host(mmc)
inactivity timer fires
vub300_queue_dead_work()
kref_get() ref = 3
queue_work(deadwork)
mmc_add_host() fails
timer_delete_sync()
mmc_free_host(mmc)
frees vub300
deadwork runs
use-after-free
The inactivity timeout is one second, so this would require
mmc_add_host() to both fail and take more than one second to do so. This
is unlikely to happen in practice, but the error path is still wrong.
timer_delete_sync() only waits for the timer callback itself. It does
not flush deadwork that the callback may already have queued. As a
result, queued deadwork can still hold a kref while the probe error path
directly frees the backing mmc host, including the vub300 storage.
Fix this by using the same lifetime mechanism as disconnect. Clear
vub300->interface so that the timer callback and any queued deadwork
return early and drop their references, then drop the initial probe
reference and return without falling through to err_free_host.
Fixes: 0613ad2401 ("mmc: vub300: fix return value check of mmc_add_host()")
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
The driver explicitly sets the .driver_data member of struct
pnp_device_id to zero without relying on that value. Drop these unused
assignments.
While touching this array use a named initializer for .id and simplify
the list terminator.
This patch doesn't modify the compiled array, only its representation in
source form benefits. The former was confirmed with an x86 build.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
The implementation of the readX() and writeX() family of IO access
functions is non-standard on ColdFire platforms. They check the supplied
IO address and will return either big or little endian results based on
that check. This is non-standard, they are expected to always return
little-endian byte ordered data. Unfortunately this behavior also means
that ioreadX()/iowroteX() and their big-endian counter parts
ioreadXbe()/iowriteXbe() are wrong. This is now in the process of being
cleaned up and fixed.
Change the use of the readX() and writeX() access functions in this driver
to use the recently defined specific ColdFire internal SoC hardware IO
access functions mcf_read8()/mcf_read16()/mcf_read32() and
mcf_write8()/mcf_write16()/mcf_write32().
There is no functional change to the driver. Though it does have the
effect of making the IO access slightly more efficient, since there is
no longer a need to do the address check at every register access.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Tested-by: Angelo Dureghello <adureghello@baylibre.com>
Acked-by: Angelo Dureghello <adureghello@baylibre.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Support for PXA93x chips was removed in commit d711b8a298 ("ARM: pxa:
remove pxa93x support"), but some code to handle them remains. Remove
it.
Discovered while searching for CONFIG_* symbols referenced in code but
not defined in any Kconfig file.
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
When transfer was stopped in STATE_DATA_BUSY state, there was no call to
dma_ops->cleanup function, so the DMA mapped buffer was never properly
unmapped. Fix this by calling dw_mci_stop_dma() function also in that
state to ensure proper cleanup call when DMA transfer was used.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
Fix logic issues introduced by the kzalloc_flex() conversion in
mmc_test_alloc_mem() due to interaction with the __counted_by
annotation on the flexible array.
Bounds-checking sanitizers rely on the counter field reflecting the
allocated array size before any array access occurs. However, use
mem->cnt both as the allocation size and as the runtime insertion
index, causing incorrect indexing and potentially invalid bounds
tracking.
Initialize mem->cnt to the maximum allocated number of segments
immediately after kzalloc_flex(), then use a separate local index
variable to track successfully allocated entries. Update mem->cnt to
the actual number of initialized elements before returning or entering
the cleanup path.
Also rewrite mmc_test_free_mem() to use a forward for-loop, improving
readability and ensuring only initialized entries are freed.
Fixes: c3126dccfd ("mmc: mmc_test: use kzalloc_flex")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
The intmask parameter of cqhci_irq() is never used within the function
body. The function reads the CQHCI interrupt status directly via
cqhci_readl() and processes interrupts independently of the SDHCI
intmask value passed by callers.
Signed-off-by: Chanwoo Lee <cw9316.lee@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
sd_enable_cache() allocates a 512-byte buffer that is never used, hence
let's just drop it.
Signed-off-by: Chanwoo Lee <cw9316.lee@samsung.com>
Reviewed-by: Avri Altman <avri.altman@sandisk.com>
Reviewed-by: Shawn Lin <shawn.lin@linux.dev>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
In the driver's probe() method, clk_disable_unprepare() for the bus clock
is called on the error path even if the prior clk_prepare_enable() call has
failed (and the same thing happens in the remove() method as well) -- that
would cause the prepare/enable counter imbalance. Also, the same problem
can happen in the driver's suspend() method; note that the resume() method
does check the clk_prepare_enable()'s result -- let's be consistent and do
that in probe() method as well. BTW, I don't know for sure what does the
bus clock control -- if it affects the register accesses, the driver will
likely cause (e.g. on ARM) a kernel oops if it fails to prepare/enable the
bus clock in the probe() method...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
Fixes: e438cf49b3 ("mmc: sdhci-of-dwcmshc: add SDHCI OF Synopsys DWC MSHC driver")
Fixes: bccce2ec77 ("mmc: sdhci-of-dwcmshc: add suspend/resume support")
Signed-off-by: Sergey Shtylyov <s.shtylyov@auroraos.dev>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
On newer Qualcomm SoCs (starting with sc7280/kodiak), ICE is modelled
as a dedicated DT node. Add the optional qcom,ice phandle to reference
that node from the SDHCI controller.
When qcom,ice is present, disallow an embedded ICE register region in
the SDHCI node to avoid double modelling. Older SoCs without qcom,ice
remain valid.
Co-developed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Co-developed-by: Abhinaba Rakshit <abhinaba.rakshit@oss.qualcomm.com>
Signed-off-by: Abhinaba Rakshit <abhinaba.rakshit@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Neeraj Soni <neeraj.soni@oss.qualcomm.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@oss.qualcomm.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
CPUs when Intel SNC (Sub-NUMA Clustering) is enabled
(Reinette Chatre)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=mae/
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2026-07-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Ingo Molnar:
- Prevent OOB access in the resctrl code while offlining
CPUs when Intel SNC (Sub-NUMA Clustering) is enabled
(Reinette Chatre)
* tag 'x86-urgent-2026-07-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86,fs/resctrl: Prevent out-of-bounds access while offlining CPU when SNC enabled
- Fix a perf_event_attr::remove_on_exec bug for group
events (Taeyang Lee)
- Fix uprobes CALL emulation interaction with shadow stacks,
and add a testcase for this (David Windsor)
- Fix uprobes unregister bug (Jiri Olsa)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Mb4z
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-2026-07-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf events fixes from Ingo Molnar:
- Fix a perf_event_attr::remove_on_exec bug for group events
(Taeyang Lee)
- Fix uprobes CALL emulation interaction with shadow stacks, and
add a testcase for this (David Windsor)
- Fix uprobes unregister bug (Jiri Olsa)
* tag 'perf-urgent-2026-07-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
uprobes/x86: Use proper mm_struct in __in_uprobe_trampoline
selftests/x86: Add shadow stack uprobe CALL test
x86/uprobes: Keep shadow stack in sync for emulated CALLs
perf/core: Detach event groups during remove_on_exec
