commit e3e056c351 upstream.
When mounting with -o modefromsid, the mode bits are stored in an
ACE. Directory enumeration (e.g. ls -l /mnt) triggers an SMB Query Dir
which does not include ACEs in its response. The mode bits in this
case are silently set to a default value of 755 instead.
This patch marks the dentry created during the directory enumeration
as needing re-evaluation (i.e. additional Query Info with ACEs) so
that the mode bits can be properly extracted.
Quick repro:
$ mount.cifs //win19.test/data /mnt -o ...,modefromsid
$ touch /mnt/foo && chmod 751 /mnt/foo
$ stat /mnt/foo
# reports 751 (OK)
$ sleep 2
# dentry older than 1s by default get invalidated
$ ls -l /mnt
# since dentry invalid, ls does a Query Dir
# and reports foo as 755 (WRONG)
Signed-off-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0dd940e58 upstream.
RHBZ: 1579050
If we have a soft mount we should fail commands for session-setup
failures (such as the password having changed/ account being deleted/ ...)
and return an error back to the application.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b57e66ad42 ]
For a cyclic work queue, when not requesting a completion per WQE,
a single CQE might indicate the completion of several WQEs.
However, in case some WQE in the batch causes an error, then an error
completion is issued, breaking the batch, and pointing to the offending
WQE in the wqe_counter field.
Hence, WQE-specific error CQE handling (like printing, breaking, etc...)
should be performed only for the last WQE in batch.
Fixes: 130c7b46c9 ("net/mlx5e: TX, Dump WQs wqe descriptors on CQE with error events")
Fixes: fd9b4be800 ("net/mlx5e: RX, Support multiple outstanding UMR posts")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 21b5f672fb ]
It turned out that on low performance systems the original change can
cause lower tx performance. On a N3450-based mini-PC tx performance
in iperf3 was reduced from 950Mbps to ~900Mbps. Therefore effectively
revert the original change, just use pcie_set_readrq() now instead of
changing the PCIe capability register directly.
Fixes: 2df49d3654 ("r8169: remove fiddling with the PCIe max read request size")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 61c00cca41 ]
Deprecate the generic TLS cap bit, use the new TX-specific
TLS cap bit instead.
Fixes: a12ff35e0f ("net/mlx5: Introduce TLS TX offload hardware bits and structures")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dfa7f70959 ]
Drop monitor uses a work item that takes care of constructing and
sending netlink notifications to user space. In case drop monitor never
started to monitor, then the work item is uninitialized and not
associated with a function.
Therefore, a stop command from user space results in canceling an
uninitialized work item which leads to the following warning [1].
Fix this by not processing a stop command if drop monitor is not
currently monitoring.
[1]
[ 31.735402] ------------[ cut here ]------------
[ 31.736470] WARNING: CPU: 0 PID: 143 at kernel/workqueue.c:3032 __flush_work+0x89f/0x9f0
...
[ 31.738120] CPU: 0 PID: 143 Comm: dwdump Not tainted 5.5.0-custom-09491-g16d4077796b8 #727
[ 31.741968] RIP: 0010:__flush_work+0x89f/0x9f0
...
[ 31.760526] Call Trace:
[ 31.771689] __cancel_work_timer+0x2a6/0x3b0
[ 31.776809] net_dm_cmd_trace+0x300/0xef0
[ 31.777549] genl_rcv_msg+0x5c6/0xd50
[ 31.781005] netlink_rcv_skb+0x13b/0x3a0
[ 31.784114] genl_rcv+0x29/0x40
[ 31.784720] netlink_unicast+0x49f/0x6a0
[ 31.787148] netlink_sendmsg+0x7cf/0xc80
[ 31.790426] ____sys_sendmsg+0x620/0x770
[ 31.793458] ___sys_sendmsg+0xfd/0x170
[ 31.802216] __sys_sendmsg+0xdf/0x1a0
[ 31.806195] do_syscall_64+0xa0/0x540
[ 31.806885] entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes: 8e94c3bc92 ("drop_monitor: Allow user to start monitoring hardware drops")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0202d293c2 ]
commit cedeac9df4 ("qed: Add support for Timestamping the unicast
PTP packets.") handles the timestamping of L4 ptp packets only.
This patch adds driver changes to detect/timestamp both L2/L4 unicast
PTP packets.
Fixes: cedeac9df4 ("qed: Add support for Timestamping the unicast PTP packets.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bfabd41da3 ]
When using taprio offloading together with ETF offloading, configured
like this, for example:
$ tc qdisc replace dev $IFACE parent root handle 100 taprio \
num_tc 4 \
map 2 2 1 0 3 2 2 2 2 2 2 2 2 2 2 2 \
queues 1@0 1@1 1@2 1@3 \
base-time $BASE_TIME \
sched-entry S 01 1000000 \
sched-entry S 0e 1000000 \
flags 0x2
$ tc qdisc replace dev $IFACE parent 100:1 etf \
offload delta 300000 clockid CLOCK_TAI
During enqueue, it works out that the verification added for the
"txtime" assisted mode is run when using taprio + ETF offloading, the
only thing missing is initializing the 'next_txtime' of all the cycle
entries. (if we don't set 'next_txtime' all packets from SO_TXTIME
sockets are dropped)
Fixes: 4cfd5779bd ("taprio: Add support for txtime-assist mode")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7c16680a08 ]
When destroying the current taprio instance, which can happen when the
creation of one fails, we should reset the traffic class configuration
back to the default state.
netdev_reset_tc() is a better way because in addition to setting the
number of traffic classes to zero, it also resets the priority to
traffic classes mapping to the default value.
Fixes: 5a781ccbd1 ("tc: Add support for configuring the taprio scheduler")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 49c684d79c ]
netlink policy validation for the 'flags' argument was missing.
Fixes: 4cfd5779bd ("taprio: Add support for txtime-assist mode")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5652e63df3 ]
If the driver implementing taprio offloading depends on the value of
the network device number of traffic classes (dev->num_tc) for
whatever reason, it was going to receive the value zero. The value was
only set after the offloading function is called.
So, moving setting the number of traffic classes to before the
offloading function is called fixes this issue. This is safe because
this only happens when taprio is instantiated (we don't allow this
configuration to be changed without first removing taprio).
Fixes: 9c66d15646 ("taprio: Add support for hardware offloading")
Reported-by: Po Liu <po.liu@nxp.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 909c1dde67 ]
The recent patch to support passive mode converter did not take care the
phy interface configuration in PCI platform data. Hence, converting all
the PCI platform data from plat->interface to plat->phy_interface as the
default mode is meant for PHY.
Fixes: 0060c87833 ("net: stmmac: implement support for passive mode converters via dt")
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Tested-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2f633d5820 ]
Without checking for IFF_MULTICAST flag, it is wrong to assume multicast
filtering is always enabled. By checking against IFF_MULTICAST, now
the driver behaves correctly when the multicast support is toggled by below
command:-
ip link set <devname> multicast off|on
Fixes: 0efedbf11f ("net: stmmac: xgmac: Fix XGMAC selftests")
Signed-off-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2ba31cd937 ]
Without checking for IFF_MULTICAST flag, it is wrong to assume multicast
filtering is always enabled. By checking against IFF_MULTICAST, now
the driver behaves correctly when the multicast support is toggled by below
command:-
ip link set <devname> multicast off|on
Fixes: 477286b53f ("stmmac: add GMAC4 core support")
Signed-off-by: Verma, Aashish <aashishx.verma@intel.com>
Tested-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 907a076881 ]
We should always do a read of current value of XGMAC_VLAN_TAG instead of
directly overwriting the register value.
Fixes: 3cd1cfcba2 ("net: stmmac: Implement VLAN Hash Filtering in XGMAC")
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9eeeb3c9de ]
It should always do a read of current value of GMAC_VLAN_TAG instead of
directly overwriting the register value.
Fixes: c1be0022df ("net: stmmac: Add VLAN HASH filtering support in GMAC4+")
Signed-off-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f822e9c4ff ]
GEM_MAX_TX_LEN currently resolves to 0x3FF8 for any IP version supporting
TSO with full 14bits of length field in payload descriptor. But an IP
errata causes false amba_error (bit 6 of ISR) when length in payload
descriptors is specified above 16387. The error occurs because the DMA
falsely concludes that there is not enough space in SRAM for incoming
payload. These errors were observed continuously under stress of large
packets using iperf on a version where SRAM was 16K for each queue. This
errata will be documented shortly and affects all versions since TSO
functionality was added. Hence limit the max length to 0x3FC0 (rounded).
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 41c1ef978c ]
The IP TSO implementation does NOT require the length to be a
multiple of 8. That is only a requirement for UFO as per IP
documentation. Hence, exit macb_features_check function in the
beginning if the protocol is not UDP. Only when it is UDP,
proceed further to the alignment checks. Update comments to
reflect the same. Also remove dead code checking for protocol
TCP when calculating header length.
Fixes: 1629dd4f76 ("cadence: Add LSO support.")
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 08db2cf577 ]
SA context is allocated at mlx5_fpga_ipsec_create_sa_ctx,
however the counterpart mlx5_fpga_ipsec_delete_sa_ctx function
nullifies sa_ctx pointer without freeing the memory allocated,
hence the memory leak.
Fix by free SA context when the SA is released.
Fixes: d6c4f0298c ("net/mlx5: Refactor accel IPSec code")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0dc2c534f1 ]
The function mlx5_fpga_esp_validate_xfrm_attrs is wrongly used
with negative negation as zero value indicates success but it
used as failure return value instead.
Fix by remove the unary not negation operator.
Fixes: 05564d0ae0 ("net/mlx5: Add flow-steering commands for FPGA IPSec implementation")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 263a425a48 ]
After a number of suspend and resume cycles, it is possible for the RBUF
to be stuck in Wake-on-LAN mode, despite the MPD enable bit being
cleared which instructed the RBUF to exit that mode.
Avoid creating that problematic condition by clearing the RX_EN and
TX_EN bits in the UniMAC prior to disable the Magic Packet Detector
logic which is guaranteed to make the RBUF exit Wake-on-LAN mode.
Fixes: 83e82f4c70 ("net: systemport: add Wake-on-LAN support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7d10f0774f ]
It forgot to reduce the value of the variable retry in a while loop
in the ethqos_configure() function. It may cause an endless loop and
without timeout.
Fixes: a7c30e62d4 ("net: stmmac: Add driver for Qualcomm ethqos")
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 52b5ae501c ]
Jakub noticed there is a potential resource leak in
tcindex_set_parms(): when tcindex_filter_result_init() fails
and it jumps to 'errout1' which doesn't release the memory
and resources allocated by tcindex_alloc_perfect_hash().
We should just jump to 'errout_alloc' which calls
tcindex_free_perfect_hash().
Fixes: b9a24bb76b ("net_sched: properly handle failure case of tcf_exts_init()")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c35947b8ff ]
Move rx_dropped and rx_errors counters in mvneta_pcpu_stats in order to
avoid possible races updating statistics
Fixes: 562e2f467e ("net: mvneta: Improve the buffer allocation method for SWBM")
Fixes: dc35a10f68 ("net: mvneta: bm: add support for hardware buffer management")
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit de34d7084e ]
The 7445 switch clocking profiles do not allow us to run the IMP port at
2Gb/sec in a way that it is reliable and consistent. Make sure that the
setting is only applied to the 7278 family.
Fixes: 8f1880cbe8 ("net: dsa: bcm_sf2: Configure IMP port for 2Gb/sec")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit df373702bc ]
b53_configure_vlan() is called by the bcm_sf2 driver upon setup and
indirectly through resume as well. During the initial setup, we are
guaranteed that dev->vlan_enabled is false, so there is no change in
behavior, however during suspend, we may have enabled VLANs before, so we
do want to restore that setting.
Fixes: dad8d7c645 ("net: dsa: b53: Properly account for VLAN filtering")
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 73a21fa817 ]
Stop removing modes that are not supported on the system interface
when the connected PHY is capable of rate adaptation. This addresses
an issue with the LS1046ARDB board 10G interface no longer working
with an 1G link partner after autonegotiation support was added
for the Aquantia PHY on board in
commit 09c4c57f7b ("net: phy: aquantia: add support for auto-negotiation configuration")
Before this commit the values advertised by the PHY were not
influenced by the dpaa_eth driver removal of system-side unsupported
modes as the aqr_config_aneg() was basically a no-op. After this
commit, the modes removed by the dpaa_eth driver were no longer
advertised thus autonegotiation with 1G link partners failed.
Reported-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d5b90e99e1 ]
commit fdd41ec21e ("devlink: Return right error code in case of errors
for region read") modified the region read code to report errors
properly in unexpected cases.
In the case where the start_offset and ret_offset match, it unilaterally
converted this into an error. This causes an issue for the "dump"
version of the command. In this case, the devlink region dump will
always report an invalid argument:
000000000000ffd0 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
000000000000ffe0 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
devlink answers: Invalid argument
000000000000fff0 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
This occurs because the expected flow for the dump is to return 0 after
there is no further data.
The simplest fix would be to stop converting the error code to -EINVAL
if start_offset == ret_offset. However, avoid unnecessary work by
checking for when start_offset is larger than the region size and
returning 0 upfront.
Fixes: fdd41ec21e ("devlink: Return right error code in case of errors for region read")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 38f88c4540 ]
syzbot managed to send an IPX packet through bond_alb_xmit()
and af_packet and triggered a use-after-free.
First, bond_alb_xmit() was using ipx_hdr() helper to reach
the IPX header, but ipx_hdr() was using the transport offset
instead of the network offset. In the particular syzbot
report transport offset was 0xFFFF
This patch removes ipx_hdr() since it was only (mis)used from bonding.
Then we need to make sure IPv4/IPv6/IPX headers are pulled
in skb->head before dereferencing anything.
BUG: KASAN: use-after-free in bond_alb_xmit+0x153a/0x1590 drivers/net/bonding/bond_alb.c:1452
Read of size 2 at addr ffff8801ce56dfff by task syz-executor.2/18108
(if (ipx_hdr(skb)->ipx_checksum != IPX_NO_CHECKSUM) ...)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
[<ffffffff8441fc42>] __dump_stack lib/dump_stack.c:17 [inline]
[<ffffffff8441fc42>] dump_stack+0x14d/0x20b lib/dump_stack.c:53
[<ffffffff81a7dec4>] print_address_description+0x6f/0x20b mm/kasan/report.c:282
[<ffffffff81a7e0ec>] kasan_report_error mm/kasan/report.c:380 [inline]
[<ffffffff81a7e0ec>] kasan_report mm/kasan/report.c:438 [inline]
[<ffffffff81a7e0ec>] kasan_report.cold+0x8c/0x2a0 mm/kasan/report.c:422
[<ffffffff81a7dc4f>] __asan_report_load_n_noabort+0xf/0x20 mm/kasan/report.c:469
[<ffffffff82c8c00a>] bond_alb_xmit+0x153a/0x1590 drivers/net/bonding/bond_alb.c:1452
[<ffffffff82c60c74>] __bond_start_xmit drivers/net/bonding/bond_main.c:4199 [inline]
[<ffffffff82c60c74>] bond_start_xmit+0x4f4/0x1570 drivers/net/bonding/bond_main.c:4224
[<ffffffff83baa558>] __netdev_start_xmit include/linux/netdevice.h:4525 [inline]
[<ffffffff83baa558>] netdev_start_xmit include/linux/netdevice.h:4539 [inline]
[<ffffffff83baa558>] xmit_one net/core/dev.c:3611 [inline]
[<ffffffff83baa558>] dev_hard_start_xmit+0x168/0x910 net/core/dev.c:3627
[<ffffffff83bacf35>] __dev_queue_xmit+0x1f55/0x33b0 net/core/dev.c:4238
[<ffffffff83bae3a8>] dev_queue_xmit+0x18/0x20 net/core/dev.c:4278
[<ffffffff84339189>] packet_snd net/packet/af_packet.c:3226 [inline]
[<ffffffff84339189>] packet_sendmsg+0x4919/0x70b0 net/packet/af_packet.c:3252
[<ffffffff83b1ac0c>] sock_sendmsg_nosec net/socket.c:673 [inline]
[<ffffffff83b1ac0c>] sock_sendmsg+0x12c/0x160 net/socket.c:684
[<ffffffff83b1f5a2>] __sys_sendto+0x262/0x380 net/socket.c:1996
[<ffffffff83b1f700>] SYSC_sendto net/socket.c:2008 [inline]
[<ffffffff83b1f700>] SyS_sendto+0x40/0x60 net/socket.c:2004
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 979923871f upstream.
Tony reported a boot regression caused by the recent workaround for systems
which have a disabled (clock gate off) PIT.
On his machine the kernel fails to initialize the PIT because
apic_needs_pit() does not take into account whether the local APIC
interrupt delivery mode will actually allow to setup and use the local
APIC timer. This should be easy to reproduce with acpi=off on the
command line which also disables HPET.
Due to the way the PIT/HPET and APIC setup ordering works (APIC setup can
require working PIT/HPET) the information is not available at the point
where apic_needs_pit() makes this decision.
To address this, split out the interrupt mode selection from
apic_intr_mode_init(), invoke the selection before making the decision
whether PIT is required or not, and add the missing checks into
apic_needs_pit().
Fixes: c8c4076723 ("x86/timer: Skip PIT initialization on modern chipsets")
Reported-by: Anthony Buckley <tony.buckley000@gmail.com>
Tested-by: Anthony Buckley <tony.buckley000@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Daniel Drake <drake@endlessm.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206125
Link: https://lore.kernel.org/r/87sgk6tmk2.fsf@nanos.tec.linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6803ee25f0 upstream.
This logic is re-used for parsing a set of online CPUs. Having it as an
isolated piece of code working with input string makes it conveninent to test
this logic as well. While refactoring, also improve the robustness of original
implementation.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191212013548.1690564-1-andriin@fb.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05d57f1793 upstream.
Though the second half of trampoline page is unused a task could be
preempted in the middle of the first half of trampoline and two
updates to trampoline would change the code from underneath the
preempted task. Hence wait for tasks to voluntarily schedule or go
to userspace. Add similar wait before freeing the trampoline.
Fixes: fec56f5890 ("bpf: Introduce BPF trampoline")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/bpf/20200121032231.3292185-1-ast@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 702204c22c upstream.
Commit f4d41ad844 ("mfd: ab8500: Example using new OF_MFD_CELL MACRO")
has a typo error renaming "ab8500-clk" to "abx500-clk"
with the result att ALSA SoC audio broke as the clock
driver was not probing anymore. Fixed it up.
Fixes: f4d41ad844 ("mfd: ab8500: Example using new OF_MFD_CELL MACRO")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c883472e1 upstream.
When RTC is used in 24H mode (and it is by this driver) the maximum
hour value is 24 in BCD. This occupies bits [5:0] - which means
correct mask for HOUR register is 0x3f not 0x1f. Fix the mask
Fixes: 32a4a4ebf7 ("rtc: bd70528: Initial support for ROHM bd70528 RTC")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f3dc25c01 upstream.
There is a bit which gets cleared after conversion.
Fixes: 9bb9e29c78 ("mfd: Add Ricoh RN5T618 PMIC core driver")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1112ba02ff upstream.
The watchdog driver compatible is "dlg,da9062-watchdog" and not
"dlg,da9062-wdt". Therefore the mfd-core can't populate the of_node and
fwnode. As result the watchdog driver can't parse the devicetree.
Fixes: 9b40b030c4 ("mfd: da9062: Supply core driver")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e19ecbf105 upstream.
Comparing the voltage of VDDA and VDDIO to determine whether or not to
enable VDDC manual override is insufficient. This is a problem in case
the VDDA is supplied from different regulator than VDDIO, while both
report the same voltage to the regulator framework. In that case where
VDDA and VDDIO is supplied by different regulators, the VDDC manual
override must not be applied.
Fixes: b6319b061b ("ASoC: sgtl5000: Fix charge pump source assignment")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Link: https://lore.kernel.org/r/20191220164450.1395038-2-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b059b7e0ec upstream.
Add regulator_is_equal() helper to compare whether two regulators are
the same. This is useful for checking whether two separate regulators
in a driver are actually the same supply.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Link: https://lore.kernel.org/r/20191220164450.1395038-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d3805af27 upstream.
If "seen_pebs = init_seen(ubi);" fails then "seen_pebs" is an error pointer
and we try to kfree() it which results in an Oops.
This patch re-arranges the error handling so now it only frees things
which have been allocated successfully.
Fixes: daef3dd1f0 ("UBI: Fastmap: Add self check to detect absent PEBs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef5aafb6e4 upstream.
set_seen() sets the bit corresponding to the PEB number in the bitmap,
so when self_check_seen() wants to find PEBs that haven't been seen we
have to print the PEBs that have their bit cleared, not the ones which
have it set.
Fixes: 5d71afb008 ("ubi: Use bitmaps in Fastmap self-check code")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ad6f58ea9 upstream.
We forget to put the inode and unmount the kernfs used for compaction.
Fixes: 71994620bb ("virtio_balloon: replace oom notifier with shrinker")
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Wei Wang <wei.w.wang@intel.com>
Cc: Liang Li <liang.z.li@intel.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20200205163402.42627-3-david@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c22dc61c7 upstream.
When unloading the driver while hinting is in progress, we will not
release the free page blocks back to MM, resulting in a memory leak.
Fixes: 86a559787e ("virtio-balloon: VIRTIO_BALLOON_F_FREE_PAGE_HINT")
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Wei Wang <wei.w.wang@intel.com>
Cc: Liang Li <liang.z.li@intel.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20200205163402.42627-2-david@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09a80f2aef upstream.
We must allow for the fact that iov_iter_write() could have returned
a short write (e.g. if there was an ENOSPC issue).
Fixes: d890be159a "nfsd: Add I/O trace points in the NFSv4 write path"
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9594497f2c upstream.
The nfsd4_blocked_lock->nbl_time timestamp is recorded in jiffies,
but then compared to a CLOCK_REALTIME timestamp later on, which makes
no sense.
For consistency with the other timestamps, change this to use a time_t.
This is a change in behavior, which may cause regressions, but the
current code is not sensible. On a system with CONFIG_HZ=1000,
the 'time_after((unsigned long)nbl->nbl_time, (unsigned long)cutoff))'
check is false for roughly the first 18 days of uptime and then true
for the next 49 days.
Fixes: 7919d0a27f ("nfsd: add a LRU list for blocked locks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
