As per updated bindings, add the clocks for those two interconnects,
which are required to set up QoS correctly.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20251114-sm6350-icc-qos-v2-5-6af348cb9c69@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
On Agatti platform the ADSP provides FastRPC support. Add corresponding
device node, in order to be able to utilize the DSP offload from the
Linux side.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260113-agatti-fastrpc-v2-1-b66870213f89@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add CoreSight DT nodes for AOSS, QDSS, CDSP, and Modem blocks to enable
the STM and TPDM sources to route trace data to the ETF for debugging.
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Jie Gan <jie.gan@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251120-add-coresight-nodes-for-pakala-v3-1-03bb7651bc90@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
QUP devices are currently marked with opp-shared in their OPP table,
causing the kernel to treat them as part of a shared OPP domain. This
leads to the qcom_geni_serial driver failing to probe with error
-EBUSY (-16).
Remove the opp-shared property to ensure the OPP framework treats the
QUP OPP table as device-specific, allowing the serial driver to probe
successfully
Fixes: f6746dc9e3 ("arm64: dts: qcom: qcs615: Add QUPv3 configuration")
Signed-off-by: Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251111170350.525832-1-viken.dadhaniya@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The watchdog support in EL1 is SBSA compliant, handled by Gunyah
hypervisor, but in EL2. the watchdog is an instance of the APSS WDT HW
block, same as older platforms. So describe the APSS WDT node and mark
it as reserved, as it will only be enabled in EL2 overlay.
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251224-arm64-dts-qcom-x1e80100-el2-add-apss-wdt-v3-2-1801c55d2883@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Document the compatible for the X1E80100 platform to the Qualcomm watchdog
binding. The HW implementation is compatible with the KPSS WDT.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251224-arm64-dts-qcom-x1e80100-el2-add-apss-wdt-v3-1-1801c55d2883@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable the CCI where the camera modules are connected to, and add a node
for the EEPROM found next to the IMX363 rear camera.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Luca Weiss <luca@lucaweiss.eu>
Link: https://lore.kernel.org/r/20251028-msm8953-cci-v2-7-b5f9f7135326@lucaweiss.eu
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the definitions for a few fixed regulators found on the Fairphone 3.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Luca Weiss <luca@lucaweiss.eu>
Link: https://lore.kernel.org/r/20251028-msm8953-cci-v2-6-b5f9f7135326@lucaweiss.eu
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Follow the Devicetree Sources Coding Style and sort the pinctrl nodes by
the pins property. This makes it simpler to add new pinctrl states in
the future.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Luca Weiss <luca@lucaweiss.eu>
Link: https://lore.kernel.org/r/20251028-msm8953-cci-v2-4-b5f9f7135326@lucaweiss.eu
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Document the Inter-Processor Communication Controller on the Qualcomm
Kaanapali and Glymur Platforms, which will be used to route interrupts
across various subsystems found on the SoC.
Co-developed-by: Sibi Sankar <sibi.sankar@oss.qualcomm.com>
Signed-off-by: Sibi Sankar <sibi.sankar@oss.qualcomm.com>
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20251031-knp-ipcc-v3-1-62ffb4168dff@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Document CPUSS Control Processor (CPUCP) mailbox controller for Qualcomm
Kaanapali, which is compatible with X1E80100, use fallback to indicate
this.
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20251021-knp-cpufreq-v2-1-95391d66c84e@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add reserved memory region for audio PD dynamic loading and remote
heap requirement. Also add LPASS and ADSP_HEAP VMIDs.
Signed-off-by: Jianping Li <jianping.li@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251117070819.492-1-jianping.li@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The Thinkpad T14s embeds a transparent 4lanes DP->HDMI transceiver
connected to the third QMP Combo PHY 4 lanes.
Add all the data routing, disable mode switching and specify the
QMP Combo PHY should be in DP-Only mode to route the 4 lanes to
the underlying DP phy.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20251119-topic-x1e80100-hdmi-v7-3-2bee0e66cc1b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Unlike the phone SoCs this was copied from, x1e has a 40-bit physical bus.
The upper address space is used to support more than 32GB of memory.
This fixes issues when DMA buffers are allocated outside the 36-bit range.
Fixes: af16b00578 ("arm64: dts: qcom: Add base X1E80100 dtsi and the QCP dts")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251127212943.24480-1-jonathan@marek.ca
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
All the Lemans IOT variants boards are using Gunyah hypervisor which
means that, so far, Linux-based OS could only boot in EL1 on those
devices. However, it is possible for us to boot Linux at EL2 on these
devices [1].
When running under Gunyah, the remote processor firmware IOMMU streams
are controlled by Gunyah. However, without Gunyah, the IOMMU is managed
by the consumer of this DeviceTree. Therefore, describe the firmware
streams for each remote processor.
Add a EL2-specific DT overlay and apply it to Lemans IOT variant
devices to create -el2.dtb for each of them alongside "normal" dtb.
[1]
https://docs.qualcomm.com/bundle/publicresource/topics/80-70020-4/boot-developer-touchpoints.html#uefi
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260105-kvmrprocv10-v10-14-022e96815380@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
On SDM845 SPI uses hardware-provided chip select, while specifying
cs-gpio makes the driver request GPIO pin, which on DB845c conflicts
with the normal host controllers pinctrl entry.
Drop the cs-gpios property to restore SPI functionality.
Fixes: cb29e7106d ("arm64: dts: qcom: db845c: Add support for MCP2517FD")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260106-wcn3990-pwrctl-v2-7-0386204328be@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Follow commit 9c92d36b0b ("arm64: dts: qcom: qrb2210-rb1: Fix UART3
wakeup IRQ storm") and apply the similar fix to the RB2 platform.
Having RX / TX pins as pull up and wakup interrupt as high-level
triggered generates an interrupt storm when trying to suspend the
device. Avoid the storm by using the falling edge trigger (as all other
platforms do).
Fixes: cab60b1665 ("arm64: dts: qcom: qrb4210-rb2: Enable bluetooth")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260106-wcn3990-pwrctl-v2-6-0386204328be@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
qcom,msm-id property must consist of two numbers, where the second
number is the subtype, as reported by dtbs_check:
sm6125-xiaomi-ginkgo.dtb: / (xiaomi,ginkgo): qcom,msm-id:0: [394] is too short
Xiaomi vendor DTS for Trinket IDP and QRD boards uses value of 0x10000,
so put it here as well.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251229142806.241088-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Unlike the CPU, the GPU does not throttle its speed automatically when it
reaches high temperatures.
Set up GPU cooling by throttling the GPU speed
when reaching 115°C.
Signed-off-by: Gaurav Kohli <quic_gkohli@quicinc.com>
Signed-off-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250903-a623-gpu-support-v5-4-5398585e2981@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add register addresses and clocks which need to be enabled for
configuring QoS on sa8775p SoC.
Signed-off-by: Odelu Kukatla <odelu.kukatla@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251001073344.6599-4-odelu.kukatla@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The ARM PMUs shares the same per-cpu (PPI) interrupt, so we need to switch
to interrupt-cells = <4> in the GIC node to allow adding an interrupt
partition map phandle as the 4th cell value for GIC_PPI interrupts.
Signed-off-by: Yuanjie Yang <yuanjie.yang@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260108092542.1371-2-yuanjie.yang@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Complete interrupts for DWC3 node to match what is required by
Devicetree bindings, as reported by dtbs_check:
ipq9574-rdp433.dtb: usb@8af8800 (qcom,ipq9574-dwc3): interrupt-names: ['pwr_event'] is too short
The actual interrupt numbers are taken from reference manual of similar
chip, but not IPQ9574, due to lack of access to it.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Kathiravan Thirumoorthy <kathiravan.thirumoorthy@oss.qualcomm.com>
Tested-by: Kathiravan Thirumoorthy <kathiravan.thirumoorthy@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260106185123.19929-4-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Interrupts for DWC3 node were completely mixed up - SPI interrupt 62 is
not listed in reference manual at all. It was also causing dtbs_check
warnings:
ipq5018-rdp432-c2.dtb: usb@8af8800 (qcom,ipq5018-dwc3): interrupt-names:0: 'pwr_event' was expected
ipq5018-rdp432-c2.dtb: usb@8af8800 (qcom,ipq5018-dwc3): interrupt-names: ['hs_phy_irq'] is too short
Warning itself was introduced by commit 53c6d854be ("dt-bindings: usb:
dwc3: Clean up hs_phy_irq in binding"), but this was trying to bring
sanity to the interrupts overall, although did a mistake for IPQ5018.
IPQ5018 does not have QUSB2 PHY and its interrupts should rather match
ones used in IPQ5332.
Correct it by using interrupts matching the bindings and reference
manual.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Tested-by: George Moussalem <george.moussalem@outlook.com>
Link: https://lore.kernel.org/r/20260106185123.19929-3-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
HAMAO IoT EVK uses PCIe5 to connect an SDX65 module for WWAN functionality
and PCIe3 to connect a SATA controller. These interfaces require multiple
voltage rails: PCIe5 needs 3.3V supplied by vreg_wwan, while PCIe3 requires
12V, 3.3V, and 3.3V AUX rails, controlled via PMIC GPIOs.
Add the required fixed regulators with related pin configuration, and
connect them to the PCIe3 and PCIe5 ports to ensure proper power for the
SDX65 module and SATA controller.
Move reset and wake GPIO properties from RC nodes to port nodes.
Signed-off-by: Ziyue Zhang <ziyue.zhang@oss.qualcomm.com>
Reviewed-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260109104504.3147745-4-ziyue.zhang@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
HAMOA IoT SOM requires PCIe3 and PCIe5 connectivity for SATA controller
and SDX65.
Add the required sideband signals (PERST#, WAKE#, CLKREQ#), pinctrl states
and power supply properties in the device tree, which PCIe3 and PCIe5
require.
Signed-off-by: Ziyue Zhang <ziyue.zhang@oss.qualcomm.com>
Reviewed-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260109104504.3147745-3-ziyue.zhang@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Since describing the PCIe PHY directly under the RC node is now
deprecated, move the references to the respective PCIe port nodes,
creating them where necessary.Also add port nodes for PCIe5 and PCIe6a
with proper PHY references.
And also move the PCIe PERST and wake GPIOs from the controller nodes to
the corresponding PCIe port nodes on Hamoa-based platforms:
- x1e001de-devkit
- x1e78100-lenovo-thinkpad-t14s
- x1e80100-asus-vivobook-s15
- x1e80100-asus-zenbook-a14
- x1e80100-dell-xps13-9345
- x1e80100-lenovo-yoga-slim7x
- x1e80100-microsoft-romulus
- x1e80100-qcp
Signed-off-by: Ziyue Zhang <ziyue.zhang@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260109104504.3147745-2-ziyue.zhang@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The LPASS LPI TLMM pin controller controls pins for use by the analog
and digital codecs, such as the PDM bus, the digital microphone pins,
and the compander pins. Add it to support the codecs.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Co-developed-by: Nickolay Goppen <setotau@mainlining.org>
Signed-off-by: Nickolay Goppen <setotau@mainlining.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260109-qcom-sdm660-lpass-lpi-dts-v1-1-d3eb84f10a39@mainlining.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Without the correct clock votes set, we may be hitting a synchronous
external abort error when touching the lpi registers.
Internal error: synchronous external abort: 0000000096000010 [#1] SMP
<...>
Call trace:
lpi_gpio_read.isra.0+0x2c/0x58 (P)
pinmux_enable_setting+0x218/0x300
pinctrl_commit_state+0xb0/0x280
pinctrl_select_state+0x28/0x48
pinctrl_bind_pins+0x1f4/0x2a0
really_probe+0x64/0x3a8
Add the clocks to fix that.
Platforms with this SoC using AudioReach won't be impacted due to
qcs6490-audioreach.dtsi already setting clocks & clock-names for
q6prmcc. The sc7280-chrome-common.dtsi has also been adjusted to keep
the behavior the same as they also do not use Elite with q6afecc.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Tested-by: Bhushan Shah <bhushan.shah@machinesoul.in> # On fairphone-fp5
Link: https://lore.kernel.org/r/20260109-kodiak-lpass-tlmm-clocks-v1-1-746112687772@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
This initial version includes support for OV9282 camera sensor.
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20260108170550.359968-4-loic.poulain@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The PM8008 device is a dedicated camera PMIC integrating all the necessary
camera power management features.
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260108170550.359968-3-loic.poulain@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add pinctrl configuration for the four available camera master clocks.
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20260108170550.359968-2-loic.poulain@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
In the same spirit as e.g. Commit 6314184be3 ("arm64: dts: qcom:
sc8180x: Drop ipa-virt interconnect") drop the resources that should
be taken care of through the clk-rpmh driver.
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250627-topic-qcs615_icc_ipa-v1-1-dc47596cde69@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable on SM8750 QRD the Iris video codec for accelerated video
encoding/decoding.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20260106-b4-sm8750-iris-dts-v4-3-97db1d1df3dd@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable on SM8750 MTP the Iris video codec for accelerated video
encoding/decoding.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20260106-b4-sm8750-iris-dts-v4-2-97db1d1df3dd@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add Iris video codec to SM8750 SoC, which comes with significantly
different powering up sequence than previous SM8650, thus different
clocks and resets. For consistency keep existing clock and clock-names
naming, so the list shares common part.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20260106-b4-sm8750-iris-dts-v4-1-97db1d1df3dd@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add a devicetree for The Fairphone (Gen. 6) smartphone, which is based
on the Milos/SM7635 SoC.
Supported functionality as of this initial submission:
* Debug UART
* Regulators (PM7550, PM8550VS, PMR735B, PM8008)
* Remoteprocs (ADSP, CDSP, MPSS, WPSS)
* Power Button, Volume Keys, Switch
* PMIC-GLINK (Charger, Fuel gauge, USB-C mode switching)
* Camera flash/torch LED
* SD card
* USB
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251210-sm7635-fp6-initial-v4-9-b05fddd8b45c@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add a devicetree description for the Milos SoC, which is for example
Snapdragon 7s Gen 3 (SM7635).
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251210-sm7635-fp6-initial-v4-8-b05fddd8b45c@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add a dts for the PMIC used e.g. with Milos SoC-based devices.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251210-sm7635-fp6-initial-v4-6-b05fddd8b45c@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Keep the different PMIC definitions in pm8550vs.dtsi disabled by
default, and only enable them in boards explicitly.
This allows to support boards better which only have pm8550vs_c, like
the Milos/SM7635-based Fairphone (Gen. 6).
Note: I assume that at least some of these devices with PM8550VS also
don't have _c, _d, _e and _g, but this patch is keeping the resulting
devicetree the same as before this change, disabling them on boards that
don't actually have those is out of scope for this patch.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20251210-sm7635-fp6-initial-v4-5-b05fddd8b45c@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
