[ Upstream commit 1f025759ba ]
Make sure that the PTP module is cleaned up if the igc_probe() fails by
calling igc_ptp_stop() on exit.
Fixes: d89f88419f ("igc: Add skeletal frame for Intel(R) 2.5G Ethernet Controller support")
Signed-off-by: Christopher S M Hall <christopher.s.hall@intel.com>
Reviewed-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26a3910afd ]
All functions in igc_ptp.c called from igc_main.c should check the
IGC_PTP_ENABLED flag. Adding check for this flag to stop and reset
functions.
Fixes: 5f2958052c ("igc: Add basic skeleton for PTP")
Signed-off-by: Christopher S M Hall <christopher.s.hall@intel.com>
Reviewed-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd7f7328d6 ]
Move ktime_get_snapshot() into the loop. If a retry does occur, a more
recent snapshot will result in a more accurate cross-timestamp.
Fixes: a90ec84837 ("igc: Add support for PTP getcrosststamp()")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Christopher S M Hall <christopher.s.hall@intel.com>
Reviewed-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e404ad95d ]
Writing to clear the PTM status 'valid' bit while the PTM cycle is
triggered results in unreliable PTM operation. To fix this, clear the
PTM 'trigger' and status after each PTM transaction.
The issue can be reproduced with the following:
$ sudo phc2sys -R 1000 -O 0 -i tsn0 -m
Note: 1000 Hz (-R 1000) is unrealistically large, but provides a way to
quickly reproduce the issue.
PHC2SYS exits with:
"ioctl PTP_OFFSET_PRECISE: Connection timed out" when the PTM transaction
fails
This patch also fixes a hang in igc_probe() when loading the igc
driver in the kdump kernel on systems supporting PTM.
The igc driver running in the base kernel enables PTM trigger in
igc_probe(). Therefore the driver is always in PTM trigger mode,
except in brief periods when manually triggering a PTM cycle.
When a crash occurs, the NIC is reset while PTM trigger is enabled.
Due to a hardware problem, the NIC is subsequently in a bad busmaster
state and doesn't handle register reads/writes. When running
igc_probe() in the kdump kernel, the first register access to a NIC
register hangs driver probing and ultimately breaks kdump.
With this patch, igc has PTM trigger disabled most of the time,
and the trigger is only enabled for very brief (10 - 100 us) periods
when manually triggering a PTM cycle. Chances that a crash occurs
during a PTM trigger are not 0, but extremely reduced.
Fixes: a90ec84837 ("igc: Add support for PTP getcrosststamp()")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Christopher S M Hall <christopher.s.hall@intel.com>
Reviewed-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0937cb5f34 ]
This reverts commit a104042e2b.
Since the original bug seems to have been around for years,
but a new issue was report with the fix, revert the fix for
now. We have a couple of weeks to figure it out for this
release, if needed.
Reported-by: Bert Karwatzki <spasswolf@web.de>
Closes: https://lore.kernel.org/linux-wireless/20250410215527.3001-1-spasswolf@web.de
Fixes: a104042e2b ("wifi: mac80211: Update skb's control block key in ieee80211_tx_dequeue()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 324dddea32 ]
The btrtl_initialize() function checks that rtl_load_file() either
had an error or it loaded a zero length file. However, if it loaded
a zero length file then the error code is not set correctly. It
results in an error pointer vs NULL bug, followed by a NULL pointer
dereference. This was detected by Smatch:
drivers/bluetooth/btrtl.c:592 btrtl_initialize() warn: passing zero to 'ERR_PTR'
Fixes: 26503ad25d ("Bluetooth: btrtl: split the device initialization into smaller parts")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb73b5a915 ]
This fixes sending MGMT_EV_DEVICE_FOUND for invalid address
(00:00:00:00:00:00) which is a regression introduced by
a2ec905d1e ("Bluetooth: fix kernel oops in store_pending_adv_report")
since in the attempt to skip storing data for extended advertisement it
actually made the code to skip the entire if statement supposed to send
MGMT_EV_DEVICE_FOUND without attempting to use the last_addr_adv which
is garanteed to be invalid for extended advertisement since we never
store anything on it.
Link: https://github.com/bluez/bluez/issues/1157
Link: https://github.com/bluez/bluez/issues/1149#issuecomment-2767215658
Fixes: a2ec905d1e ("Bluetooth: fix kernel oops in store_pending_adv_report")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9beb2c91fb ]
Set maximum DMA segment size to 2G instead of UINT_MAX due to HW limit.
Fixes: e0477b34d9 ("RDMA: Explicitly pass in the dma_device to ib_register_device")
Link: https://patch.msgid.link/r/20250327114724.3454268-3-huangjunxian6@hisilicon.com
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72eea84a10 ]
Add goto to ensure scsi_host_put() is called in all error paths of
iscsi_set_host_param() function. This fixes a potential memory leak when
strlen() check fails.
Fixes: ce51c81700 ("scsi: iscsi: Add strlen() check in iscsi_if_set{_host}_param()")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20250318094344.91776-1-linmq006@gmail.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0f0dc96de ]
The skb dequeued from tx_queue is lost when wl1251_ps_elp_wakeup fails
with a -ETIMEDOUT error. Fix that by queueing the skb back to tx_queue.
Fixes: c5483b7193 ("wl12xx: check if elp wakeup failed")
Signed-off-by: Abdun Nihaal <abdun.nihaal@gmail.com>
Reviewed-by: Michael Nemanov <michael.nemanov@ti.com>
Link: https://patch.msgid.link/20250330104532.44935-1-abdun.nihaal@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a104042e2b ]
The ieee80211 skb control block key (set when skb was queued) could have
been removed before ieee80211_tx_dequeue() call. ieee80211_tx_dequeue()
already called ieee80211_tx_h_select_key() to get the current key, but
the latter do not update the key in skb control block in case it is
NULL. Because some drivers actually use this key in their TX callbacks
(e.g. ath1{1,2}k_mac_op_tx()) this could lead to the use after free
below:
BUG: KASAN: slab-use-after-free in ath11k_mac_op_tx+0x590/0x61c
Read of size 4 at addr ffffff803083c248 by task kworker/u16:4/1440
CPU: 3 UID: 0 PID: 1440 Comm: kworker/u16:4 Not tainted 6.13.0-ge128f627f404 #2
Hardware name: HW (DT)
Workqueue: bat_events batadv_send_outstanding_bcast_packet
Call trace:
show_stack+0x14/0x1c (C)
dump_stack_lvl+0x58/0x74
print_report+0x164/0x4c0
kasan_report+0xac/0xe8
__asan_report_load4_noabort+0x1c/0x24
ath11k_mac_op_tx+0x590/0x61c
ieee80211_handle_wake_tx_queue+0x12c/0x1c8
ieee80211_queue_skb+0xdcc/0x1b4c
ieee80211_tx+0x1ec/0x2bc
ieee80211_xmit+0x224/0x324
__ieee80211_subif_start_xmit+0x85c/0xcf8
ieee80211_subif_start_xmit+0xc0/0xec4
dev_hard_start_xmit+0xf4/0x28c
__dev_queue_xmit+0x6ac/0x318c
batadv_send_skb_packet+0x38c/0x4b0
batadv_send_outstanding_bcast_packet+0x110/0x328
process_one_work+0x578/0xc10
worker_thread+0x4bc/0xc7c
kthread+0x2f8/0x380
ret_from_fork+0x10/0x20
Allocated by task 1906:
kasan_save_stack+0x28/0x4c
kasan_save_track+0x1c/0x40
kasan_save_alloc_info+0x3c/0x4c
__kasan_kmalloc+0xac/0xb0
__kmalloc_noprof+0x1b4/0x380
ieee80211_key_alloc+0x3c/0xb64
ieee80211_add_key+0x1b4/0x71c
nl80211_new_key+0x2b4/0x5d8
genl_family_rcv_msg_doit+0x198/0x240
<...>
Freed by task 1494:
kasan_save_stack+0x28/0x4c
kasan_save_track+0x1c/0x40
kasan_save_free_info+0x48/0x94
__kasan_slab_free+0x48/0x60
kfree+0xc8/0x31c
kfree_sensitive+0x70/0x80
ieee80211_key_free_common+0x10c/0x174
ieee80211_free_keys+0x188/0x46c
ieee80211_stop_mesh+0x70/0x2cc
ieee80211_leave_mesh+0x1c/0x60
cfg80211_leave_mesh+0xe0/0x280
cfg80211_leave+0x1e0/0x244
<...>
Reset SKB control block key before calling ieee80211_tx_h_select_key()
to avoid that.
Fixes: bb42f2d13f ("mac80211: Move reorder-sensitive TX handlers to after TXQ dequeue")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Link: https://patch.msgid.link/06aa507b853ca385ceded81c18b0a6dd0f081bc8.1742833382.git.repk@triplefau.lt
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27c7e63b3c ]
The memory pointed to by priv is freed at the end of at76_delete_device
function (using ieee80211_free_hw). But the code then accesses the udev
field of the freed object to put the USB device. This may also lead to a
memory leak of the usb device. Fix this by using udev from interface.
Fixes: 29e20aa6c6 ("at76c50x-usb: fix use after free on failure path in at76_probe()")
Signed-off-by: Abdun Nihaal <abdun.nihaal@gmail.com>
Link: https://patch.msgid.link/20250330103110.44080-1-abdun.nihaal@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8aa580cd92 ]
when a SATA disk is directly connected the SAS controller determines the
disk to which I/Os are delivered based on the port ID in the DQ entry.
When many phys are disconnected and reconnect, the port ID of phys were
changed and used by other link, resulting in I/O being sent to incorrect
disk. Data inconsistency on the SATA disk may occur during I/O retries
using the old port ID. So enable force phy, then force the command to be
executed in a certain phy, and if the actual phy ID of the port does not
match the phy configured in the command, the chip will stop delivering the
I/O to disk.
Fixes: ce60689e12 ("scsi: hisi_sas: add v3 code to send ATA frame")
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Link: https://lore.kernel.org/r/20250312095135.3048379-2-yangxingui@huawei.com
Reviewed-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbfe82cdba ]
Some of the LLDDs which use libsas have their own definition of a struct
to hold TMF info, so add a common struct for libsas.
Also add an interim force phy id field for hisi_sas driver, which will be
removed once the STP "TMF" code is factored out.
Even though some LLDDs (pm8001) use a u32 for the tag, u16 will be adequate,
as that named driver only uses tags in range [0, 1024).
Link: https://lore.kernel.org/r/1645112566-115804-8-git-send-email-john.garry@huawei.com
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 8aa580cd92 ("scsi: hisi_sas: Enable force phy when SATA disk directly connected")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25882c82f8 ]
This callback is never called, so remove support.
Link: https://lore.kernel.org/r/1645112566-115804-4-git-send-email-john.garry@huawei.com
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 8aa580cd92 ("scsi: hisi_sas: Enable force phy when SATA disk directly connected")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c763ec4c10 ]
The hisi_sas_slot.is_internal member is not set properly for ATA commands
which the driver sends directly. A TMF struct pointer is normally used as a
test to set this, but it is NULL for those commands. It's not ideal, but
pass an empty TMF struct to set that member properly.
Link: https://lore.kernel.org/r/1643627607-138785-1-git-send-email-john.garry@huawei.com
Fixes: dc313f6b12 ("scsi: hisi_sas: Factor out task prep and delivery code")
Reported-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 8aa580cd92 ("scsi: hisi_sas: Enable force phy when SATA disk directly connected")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc313f6b12 ]
The task prep code is the same between the normal path (in
hisi_sas_task_prep()) and the internal abort path, so factor is out into a
common function.
Link: https://lore.kernel.org/r/1639579061-179473-5-git-send-email-john.garry@huawei.com
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 8aa580cd92 ("scsi: hisi_sas: Enable force phy when SATA disk directly connected")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08c61b5d90 ]
To help factor out code in future, it's useful to know if we're executing
an internal abort, so pass a pointer to the structure. The idea is that a
NULL pointer means not an internal abort.
Link: https://lore.kernel.org/r/1639579061-179473-4-git-send-email-john.garry@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 8aa580cd92 ("scsi: hisi_sas: Enable force phy when SATA disk directly connected")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e4620856b ]
Currently we start delivery of commands to the DQ after returning from
hisi_sas_task_exec() with success.
Let's just start delivery directly in that function without having to check
if some local variable is set.
Link: https://lore.kernel.org/r/1639579061-179473-2-git-send-email-john.garry@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 8aa580cd92 ("scsi: hisi_sas: Enable force phy when SATA disk directly connected")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5df5dafc17 upstream.
Do not set 'HCI_UART_PROTO_READY' before call 'hci_uart_register_dev()'.
Possible race is when someone calls 'hci_tty_uart_close()' after this bit
is set, but 'hci_uart_register_dev()' wasn't done. This leads to access
to uninitialized fields. To fix it let's set this bit after device was
registered (as before patch c411c62cc133) and to fix previous problem let's
add one more bit in addition to 'HCI_UART_PROTO_READY' which allows to
perform power up without original bit set (pls see commit c411c62cc133).
Crash backtrace from syzbot report:
RIP: 0010:skb_queue_empty_lockless include/linux/skbuff.h:1887 [inline]
RIP: 0010:skb_queue_purge_reason+0x6d/0x140 net/core/skbuff.c:3936
Call Trace:
<TASK>
skb_queue_purge include/linux/skbuff.h:3364 [inline]
mrvl_close+0x2f/0x90 drivers/bluetooth/hci_mrvl.c:100
hci_uart_tty_close+0xb6/0x120 drivers/bluetooth/hci_ldisc.c:557
tty_ldisc_close drivers/tty/tty_ldisc.c:455 [inline]
tty_ldisc_kill+0x66/0xc0 drivers/tty/tty_ldisc.c:613
tty_ldisc_release+0xc9/0x120 drivers/tty/tty_ldisc.c:781
tty_release_struct+0x10/0x80 drivers/tty/tty_io.c:1690
tty_release+0x4ef/0x640 drivers/tty/tty_io.c:1861
__fput+0x86/0x2a0 fs/file_table.c:450
task_work_run+0x82/0xb0 kernel/task_work.c:239
resume_user_mode_work include/linux/resume_user_mode.h:50 [inline]
exit_to_user_mode_loop kernel/entry/common.c:114 [inline]
exit_to_user_mode_prepare include/linux/entry-common.h:329 [inline]
__syscall_exit_to_user_mode_work kernel/entry/common.c:207 [inline]
syscall_exit_to_user_mode+0xa3/0x1b0 kernel/entry/common.c:218
do_syscall_64+0x9a/0x190 arch/x86/entry/common.c:89
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Reported-by: syzbot+683f8cb11b94b1824c77@syzkaller.appspotmail.com
Tested-by: syzbot+683f8cb11b94b1824c77@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-bluetooth/d159c57f-8490-4c26-79da-6ad3612c4a14@salutedevices.com/
Fixes: 366ceff495 ("Bluetooth: hci_uart: fix race during initialization")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2f29da9f0 upstream.
While debugging kexec/hibernation hangs and crashes, it turned out that
the current implementation of e820__register_nosave_regions() suffers from
multiple serious issues:
- The end of last region is tracked by PFN, causing it to find holes
that aren't there if two consecutive subpage regions are present
- The nosave PFN ranges derived from holes are rounded out (instead of
rounded in) which makes it inconsistent with how explicitly reserved
regions are handled
Fix this by:
- Treating reserved regions as if they were holes, to ensure consistent
handling (rounding out nosave PFN ranges is more correct as the
kernel does not use partial pages)
- Tracking the end of the last RAM region by address instead of pages
to detect holes more precisely
These bugs appear to have been introduced about ~18 years ago with the very
first version of e820_mark_nosave_regions(), and its flawed assumptions were
carried forward uninterrupted through various waves of rewrites and renames.
[ mingo: Added Git archeology details, for kicks and giggles. ]
Fixes: e8eff5ac29 ("[PATCH] Make swsusp avoid memory holes and reserved memory regions on x86_64")
Reported-by: Roberto Ricci <io@r-ricci.it>
Tested-by: Roberto Ricci <io@r-ricci.it>
Signed-off-by: Myrrh Periwinkle <myrrhperiwinkle@qtmlabs.xyz>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Len Brown <len.brown@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250406-fix-e820-nosave-v3-1-f3787bc1ee1d@qtmlabs.xyz
Closes: https://lore.kernel.org/all/Z4WFjBVHpndct7br@desktop0a/
Signed-off-by: Myrrh Periwinkle <myrrhperiwinkle@qtmlabs.xyz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd4f730b55 upstream.
When an attribute group is created with sysfs_create_group(), the
->sysfs_ops() callback is set to kobj_sysfs_ops, which sets the ->show()
and ->store() callbacks to kobj_attr_show() and kobj_attr_store()
respectively. These functions use container_of() to get the respective
callback from the passed attribute, meaning that these callbacks need to
be of the same type as the callbacks in 'struct kobj_attribute'.
However, ->show() and ->store() in the platform_profile driver are
defined for struct device_attribute with the help of DEVICE_ATTR_RO()
and DEVICE_ATTR_RW(), which results in a CFI violation when accessing
platform_profile or platform_profile_choices under /sys/firmware/acpi
because the types do not match:
CFI failure at kobj_attr_show+0x19/0x30 (target: platform_profile_choices_show+0x0/0x140; expected type: 0x7a69590c)
There is no functional issue from the type mismatch because the layout
of 'struct kobj_attribute' and 'struct device_attribute' are the same,
so the container_of() cast does not break anything aside from CFI.
Change the type of platform_profile_choices_show() and
platform_profile_{show,store}() to match the callbacks in
'struct kobj_attribute' and update the attribute variables to
match, which resolves the CFI violation.
Cc: All applicable <stable@vger.kernel.org>
Fixes: a2ff95e018 ("ACPI: platform: Add platform profile support")
Reported-by: John Rowley <lkml@johnrowley.me>
Closes: https://github.com/ClangBuiltLinux/linux/issues/2047
Tested-by: John Rowley <lkml@johnrowley.me>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://patch.msgid.link/20250210-acpi-platform_profile-fix-cfi-violation-v3-1-ed9e9901c33a@kernel.org
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[nathan: Fix conflicts in older stable branches]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5951389e5 upstream.
When comparing to the ARM list [1], it appears that several ARM cores
were missing from the lists in spectre_bhb_loop_affected(). Add them.
NOTE: for some of these cores it may not matter since other ways of
clearing the BHB may be used (like the CLRBHB instruction or ECBHB),
but it still seems good to have all the info from ARM's whitepaper
included.
[1] https://developer.arm.com/Arm%20Security%20Center/Spectre-BHB
Fixes: 558c303c97 ("arm64: Mitigate spectre style branch history side channels")
Cc: stable@vger.kernel.org
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: James Morse <james.morse@arm.com>
Link: https://lore.kernel.org/r/20250107120555.v4.5.I4a9a527e03f663040721c5401c41de587d015c82@changeid
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3f88665a7 upstream.
In the ssi_protocol_probe() function, &ssi->work is bound with
ssip_xmit_work(), In ssip_pn_setup(), the ssip_pn_xmit() function
within the ssip_pn_ops structure is capable of starting the
work.
If we remove the module which will call ssi_protocol_remove()
to make a cleanup, it will free ssi through kfree(ssi),
while the work mentioned above will be used. The sequence
of operations that may lead to a UAF bug is as follows:
CPU0 CPU1
| ssip_xmit_work
ssi_protocol_remove |
kfree(ssi); |
| struct hsi_client *cl = ssi->cl;
| // use ssi
Fix it by ensuring that the work is canceled before proceeding
with the cleanup in ssi_protocol_remove().
Signed-off-by: Kaixin Wang <kxwang23@m.fudan.edu.cn>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240918120749.1730-1-kxwang23@m.fudan.edu.cn
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e225128c3f upstream.
When submitting the TLMM test driver, Bjorn reported that some of the test
cases are failing for GPIOs that not are backed by PDC (i.e. "non-wakeup"
GPIOs that are handled directly in pinctrl-msm). Basically, lingering
latched interrupt state is still being delivered at IRQ request time, e.g.:
ok 1 tlmm_test_silent_rising
tlmm_test_silent_falling: ASSERTION FAILED at drivers/pinctrl/qcom/tlmm-test.c:178
Expected atomic_read(&priv->intr_count) == 0, but
atomic_read(&priv->intr_count) == 1 (0x1)
not ok 2 tlmm_test_silent_falling
tlmm_test_silent_low: ASSERTION FAILED at drivers/pinctrl/qcom/tlmm-test.c:178
Expected atomic_read(&priv->intr_count) == 0, but
atomic_read(&priv->intr_count) == 1 (0x1)
not ok 3 tlmm_test_silent_low
ok 4 tlmm_test_silent_high
Whether to report interrupts that came in while the IRQ was unclaimed
doesn't seem to be well-defined in the Linux IRQ API. However, looking
closer at these specific cases, we're actually reporting events that do not
match the interrupt type requested by the driver:
1. After "ok 1 tlmm_test_silent_rising", the GPIO is in low state and
configured for IRQF_TRIGGER_RISING.
2. (a) In preparation for "tlmm_test_silent_falling", the GPIO is switched
to high state. The rising interrupt gets latched.
(b) The GPIO is re-configured for IRQF_TRIGGER_FALLING, but the latched
interrupt isn't cleared.
(c) The IRQ handler is called for the latched interrupt, but there
wasn't any falling edge.
3. (a) For "tlmm_test_silent_low", the GPIO remains in high state.
(b) The GPIO is re-configured for IRQF_TRIGGER_LOW. This seems to
result in a phantom interrupt that gets latched.
(c) The IRQ handler is called for the latched interrupt, but the GPIO
isn't in low state.
4. (a) For "tlmm_test_silent_high", the GPIO is switched to low state.
(b) This doesn't result in a latched interrupt, because RAW_STATUS_EN
was cleared when masking the level-triggered interrupt.
Fix this by clearing the interrupt state whenever making any changes to the
interrupt configuration. This includes previously disabled interrupts, but
also any changes to interrupt polarity or detection type.
With this change, all 16 test cases are now passing for the non-wakeup
GPIOs in the TLMM.
Cc: stable@vger.kernel.org
Fixes: cf9d052aa6 ("pinctrl: qcom: Don't clear pending interrupts when enabling")
Reported-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Closes: https://lore.kernel.org/r/20250227-tlmm-test-v1-1-d18877b4a5db@oss.qualcomm.com/
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Tested-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/20250312-pinctrl-msm-type-latch-v1-1-ce87c561d3d7@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f2768b6a3 upstream.
If device_register(&child->dev) fails, call put_device() to explicitly
release child->dev, per the comment at device_register().
Found by code review.
Link: https://lore.kernel.org/r/20250202062357.872971-1-make24@iscas.ac.cn
Fixes: 4f535093cf ("PCI: Put pci_dev in device tree as early as possible")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2df181e1ae upstream.
A call to of_parse_phandle() is incrementing the refcount, and as such,
the of_node_put() must be called when the reference is no longer needed.
Thus, refactor the existing code and add a missing of_node_put() call
following the check to ensure that "msi_np" matches "pcie->np" and after
MSI initialization, but only if the MSI support is enabled system-wide.
Cc: stable@vger.kernel.org # v5.10+
Fixes: 40ca1bf580 ("PCI: brcmstb: Add MSI support")
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250122222955.1752778-1-svarbanov@suse.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 708124d9e6 upstream.
of_irq_init() will leak interrupt controller device node refcounts
in two places as explained below:
1) Leak refcounts of both @desc->dev and @desc->interrupt_parent when
suffers @desc->irq_init_cb() failure.
2) Leak refcount of @desc->interrupt_parent when cleans up list
@intc_desc_list in the end.
Refcounts of both @desc->dev and @desc->interrupt_parent were got in
the first loop, but of_irq_init() does not put them before kfree(@desc)
in places mentioned above, so causes refcount leakages.
Fix by putting refcounts involved before kfree(@desc).
Fixes: 8363ccb917 ("of/irq: add missing of_node_put")
Fixes: c71a54b082 ("of/irq: introduce of_irq_init")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20250209-of_irq_fix-v2-7-93e3a2659aa7@quicinc.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 962a2805e4 upstream.
In irq_of_parse_and_map(), refcount of device node @oirq.np was got
by successful of_irq_parse_one() invocation, but it does not put the
refcount before return, so causes @oirq.np refcount leakage.
Fix by putting @oirq.np refcount before return.
Fixes: e387344499 ("of/irq: Move irq_of_parse_and_map() to common code")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20250209-of_irq_fix-v2-6-93e3a2659aa7@quicinc.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bbf71f44aa upstream.
of_irq_count() invokes of_irq_parse_one() to count IRQs, and successful
invocation of the later will get device node @irq.np refcount, but the
former does not put the refcount before next iteration invocation, hence
causes device node refcount leakages.
Fix by putting @irq.np refcount before the next iteration invocation.
Fixes: 3da5278727 ("of/irq: Rework of_irq_count()")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20250209-of_irq_fix-v2-5-93e3a2659aa7@quicinc.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd5625fc86 upstream.
msi_db_mask is of type 'u64', still the standard 'int' arithmetic is
performed to compute its value.
While most of the ntb_hw drivers actually don't utilize the higher 32
bits of the doorbell mask now, this may be the case for Switchtec - see
switchtec_ntb_init_db().
Found by Linux Verification Center (linuxtesting.org) with SVACE static
analysis tool.
Fixes: 2b0569b3b7 ("NTB: Add MSI interrupt support to ntb_transport")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42ea22e754 upstream.
When the kernel contains a large number of functions that can be traced,
the loop in ftrace_graph_set_hash() may take a lot of time to execute.
This may trigger the softlockup watchdog.
Add cond_resched() within the loop to allow the kernel to remain
responsive even when processing a large number of functions.
This matches the cond_resched() that is used in other locations of the
code that iterates over all functions that can be traced.
Cc: stable@vger.kernel.org
Fixes: b9b0c831be ("ftrace: Convert graph filter to use hash tables")
Link: https://lore.kernel.org/tencent_3E06CE338692017B5809534B9C5C03DA7705@qq.com
Signed-off-by: zhoumin <teczm@foxmail.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00204ae3d6 upstream.
The dm-integrity target didn't set the error string when memory
allocation failed. This patch fixes it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07bb097b92 upstream.
Currently, the ASP primary device check does not have support for PCI
domains, and, as a result, when the system is configured with PCI domains
(PCI segments) the wrong device can be selected as primary. This results
in commands submitted to the device timing out and failing. The device
check also relies on specific device and function assignments that may
not hold in the future.
Fix the primary ASP device check to include support for PCI domains and
to perform proper checking of the Bus/Device/Function positions.
Fixes: 2a6170dfe7 ("crypto: ccp: Add Platform Security Processor (PSP) device support")
Cc: stable@vger.kernel.org
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee022e5cae upstream.
The mapping table for the rk3328 is missing the entry for -25C which is
found in the TRM section 9.5.2 "Temperature-to-code mapping".
NOTE: the kernel uses the tsadc_q_sel=1'b1 mode which is defined as:
4096-<code in table>. Whereas the table in the TRM gives the code
"3774" for -25C, the kernel uses 4096-3774=322.
[Dragan Simic] : "After going through the RK3308 and RK3328 TRMs, as
well as through the downstream kernel code, it seems we may have
some troubles at our hands. Let me explain, please.
To sum it up, part 1 of the RK3308 TRM v1.1 says on page 538 that
the equation for the output when tsadc_q_sel equals 1 is (4096 -
tsadc_q), while part 1 of the RK3328 TRM v1.2 says that the output
equation is (1024 - tsadc_q) in that case.
The downstream kernel code, however, treats the RK3308 and RK3328
tables and their values as being the same. It even mentions 1024 as
the "offset" value in a comment block for the rk_tsadcv3_control()
function, just like the upstream code does, which is obviously wrong
"offset" value when correlated with the table on page 544 of part 1
of the RK3308 TRM v1.1.
With all this in mind, it's obvious that more work is needed to make
it clear where's the actual mistake (it could be that the TRM is
wrong), which I'll volunteer for as part of the SoC binning project.
In the meantime, this patch looks fine as-is to me, by offering
what's a clear improvement to the current state of the upstream
code"
Link: https://opensource.rock-chips.com/images/9/97/Rockchip_RK3328TRM_V1.1-Part1-20170321.pdf
Cc: stable@vger.kernel.org
Fixes: eda519d5f7 ("thermal: rockchip: Support the RK3328 SOC in thermal driver")
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20250207175048.35959-1-twoerner@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1a69a940d upstream.
sctp_sendmsg() re-uses associations and transports when possible by
doing a lookup based on the socket endpoint and the message destination
address, and then sctp_sendmsg_to_asoc() sets the selected transport in
all the message chunks to be sent.
There's a possible race condition if another thread triggers the removal
of that selected transport, for instance, by explicitly unbinding an
address with setsockopt(SCTP_SOCKOPT_BINDX_REM), after the chunks have
been set up and before the message is sent. This can happen if the send
buffer is full, during the period when the sender thread temporarily
releases the socket lock in sctp_wait_for_sndbuf().
This causes the access to the transport data in
sctp_outq_select_transport(), when the association outqueue is flushed,
to result in a use-after-free read.
This change avoids this scenario by having sctp_transport_free() signal
the freeing of the transport, tagging it as "dead". In order to do this,
the patch restores the "dead" bit in struct sctp_transport, which was
removed in
commit 47faa1e4c5 ("sctp: remove the dead field of sctp_transport").
Then, in the scenario where the sender thread has released the socket
lock in sctp_wait_for_sndbuf(), the bit is checked again after
re-acquiring the socket lock to detect the deletion. This is done while
holding a reference to the transport to prevent it from being freed in
the process.
If the transport was deleted while the socket lock was relinquished,
sctp_sendmsg_to_asoc() will return -EAGAIN to let userspace retry the
send.
The bug was found by a private syzbot instance (see the error report [1]
and the C reproducer that triggers it [2]).
Link: https://people.igalia.com/rcn/kernel_logs/20250402__KASAN_slab-use-after-free_Read_in_sctp_outq_select_transport.txt [1]
Link: https://people.igalia.com/rcn/kernel_logs/20250402__KASAN_slab-use-after-free_Read_in_sctp_outq_select_transport__repro.c [2]
Cc: stable@vger.kernel.org
Fixes: df132eff46 ("sctp: clear the transport of some out_chunk_list chunks in sctp_assoc_rm_peer")
Suggested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Ricardo Cañuelo Navarro <rcn@igalia.com>
Acked-by: Xin Long <lucien.xin@gmail.com>
Link: https://patch.msgid.link/20250404-kasan_slab-use-after-free_read_in_sctp_outq_select_transport__20250404-v1-1-5ce4a0b78ef2@igalia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aaf99ac2ce upstream.
When an uncorrected memory error is consumed there is a race between the
CMCI from the memory controller reporting an uncorrected error with a UCNA
signature, and the core reporting and SRAR signature machine check when
the data is about to be consumed.
- Background: why *UN*corrected errors tied to *C*MCI in Intel platform [1]
Prior to Icelake memory controllers reported patrol scrub events that
detected a previously unseen uncorrected error in memory by signaling a
broadcast machine check with an SRAO (Software Recoverable Action
Optional) signature in the machine check bank. This was overkill because
it's not an urgent problem that no core is on the verge of consuming that
bad data. It's also found that multi SRAO UCE may cause nested MCE
interrupts and finally become an IERR.
Hence, Intel downgrades the machine check bank signature of patrol scrub
from SRAO to UCNA (Uncorrected, No Action required), and signal changed to
#CMCI. Just to add to the confusion, Linux does take an action (in
uc_decode_notifier()) to try to offline the page despite the UC*NA*
signature name.
- Background: why #CMCI and #MCE race when poison is consuming in Intel platform [1]
Having decided that CMCI/UCNA is the best action for patrol scrub errors,
the memory controller uses it for reads too. But the memory controller is
executing asynchronously from the core, and can't tell the difference
between a "real" read and a speculative read. So it will do CMCI/UCNA if
an error is found in any read.
Thus:
1) Core is clever and thinks address A is needed soon, issues a speculative read.
2) Core finds it is going to use address A soon after sending the read request
3) The CMCI from the memory controller is in a race with MCE from the core
that will soon try to retire the load from address A.
Quite often (because speculation has got better) the CMCI from the memory
controller is delivered before the core is committed to the instruction
reading address A, so the interrupt is taken, and Linux offlines the page
(marking it as poison).
- Why user process is killed for instr case
Commit 046545a661 ("mm/hwpoison: fix error page recovered but reported
"not recovered"") tries to fix noise message "Memory error not recovered"
and skips duplicate SIGBUSs due to the race. But it also introduced a bug
that kill_accessing_process() return -EHWPOISON for instr case, as result,
kill_me_maybe() send a SIGBUS to user process.
If the CMCI wins that race, the page is marked poisoned when
uc_decode_notifier() calls memory_failure(). For dirty pages,
memory_failure() invokes try_to_unmap() with the TTU_HWPOISON flag,
converting the PTE to a hwpoison entry. As a result,
kill_accessing_process():
- call walk_page_range() and return 1 regardless of whether
try_to_unmap() succeeds or fails,
- call kill_proc() to make sure a SIGBUS is sent
- return -EHWPOISON to indicate that SIGBUS is already sent to the
process and kill_me_maybe() doesn't have to send it again.
However, for clean pages, the TTU_HWPOISON flag is cleared, leaving the
PTE unchanged and not converted to a hwpoison entry. Conversely, for
clean pages where PTE entries are not marked as hwpoison,
kill_accessing_process() returns -EFAULT, causing kill_me_maybe() to send
a SIGBUS.
Console log looks like this:
Memory failure: 0x827ca68: corrupted page was clean: dropped without side effects
Memory failure: 0x827ca68: recovery action for clean LRU page: Recovered
Memory failure: 0x827ca68: already hardware poisoned
mce: Memory error not recovered
To fix it, return 0 for "corrupted page was clean", preventing an
unnecessary SIGBUS to user process.
[1] https://lore.kernel.org/lkml/20250217063335.22257-1-xueshuai@linux.alibaba.com/T/#mba94f1305b3009dd340ce4114d3221fe810d1871
Link: https://lkml.kernel.org/r/20250312112852.82415-3-xueshuai@linux.alibaba.com
Fixes: 046545a661 ("mm/hwpoison: fix error page recovered but reported "not recovered"")
Signed-off-by: Shuai Xue <xueshuai@linux.alibaba.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Acked-by: Miaohe Lin <linmiaohe@huawei.com>
Cc: Baolin Wang <baolin.wang@linux.alibaba.com>
Cc: Borislav Betkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jane Chu <jane.chu@oracle.com>
Cc: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Josh Poimboeuf <jpoimboe@kernel.org>
Cc: Naoya Horiguchi <nao.horiguchi@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ruidong Tian <tianruidong@linux.alibaba.com>
Cc: Thomas Gleinxer <tglx@linutronix.de>
Cc: Yazen Ghannam <yazen.ghannam@amd.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0ebbb3841 upstream.
The PGDAT_RECLAIM_LOCKED bit is used to provide mutual exclusion of node
reclaim for struct pglist_data using a single bit.
It is "locked" with a test_and_set_bit (similarly to a try lock) which
provides full ordering with respect to loads and stores done within
__node_reclaim().
It is "unlocked" with clear_bit(), which does not provide any ordering
with respect to loads and stores done before clearing the bit.
The lack of clear_bit() memory ordering with respect to stores within
__node_reclaim() can cause a subsequent CPU to fail to observe stores from
a prior node reclaim. This is not an issue in practice on TSO (e.g.
x86), but it is an issue on weakly-ordered architectures (e.g. arm64).
Fix this by using clear_bit_unlock rather than clear_bit to clear
PGDAT_RECLAIM_LOCKED with a release memory ordering semantic.
This provides stronger memory ordering (release rather than relaxed).
Link: https://lkml.kernel.org/r/20250312141014.129725-1-mathieu.desnoyers@efficios.com
Fixes: d773ed6b85 ("mm: test and set zone reclaim lock before starting reclaim")
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrea Parri <parri.andrea@gmail.com>
Cc: Will Deacon <will@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jade Alglave <j.alglave@ucl.ac.uk>
Cc: Luc Maranget <luc.maranget@inria.fr>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1d416bf9f upstream.
Since commit 38e0edb15b ("mm/apply_to_range: call pte function with lazy
updates") it's been possible for arch_[enter|leave]_lazy_mmu_mode() to be
called without holding a page table lock (for the kernel mappings case),
and therefore it is possible that preemption may occur while in the lazy
mmu mode. The Sparc lazy mmu implementation is not robust to preemption
since it stores the lazy mode state in a per-cpu structure and does not
attempt to manage that state on task switch.
Powerpc had the same issue and fixed it by explicitly disabling preemption
in arch_enter_lazy_mmu_mode() and re-enabling in
arch_leave_lazy_mmu_mode(). See commit b9ef323ea1 ("powerpc/64s:
Disable preemption in hash lazy mmu mode").
Given Sparc's lazy mmu mode is based on powerpc's, let's fix it in the
same way here.
Link: https://lkml.kernel.org/r/20250303141542.3371656-4-ryan.roberts@arm.com
Fixes: 38e0edb15b ("mm/apply_to_range: call pte function with lazy updates")
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Borislav Betkov <bp@alien8.de>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Juegren Gross <jgross@suse.com>
Cc: Matthew Wilcow (Oracle) <willy@infradead.org>
Cc: Thomas Gleinxer <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46ad360020 upstream.
The MT8173 disp-pwm device should have only one compatible string, based
on the following DT validation error:
arch/arm64/boot/dts/mediatek/mt8173-elm.dtb: pwm@1401e000: compatible: 'oneOf' conditional failed, one must be fixed:
['mediatek,mt8173-disp-pwm', 'mediatek,mt6595-disp-pwm'] is too long
'mediatek,mt8173-disp-pwm' is not one of ['mediatek,mt6795-disp-pwm', 'mediatek,mt8167-disp-pwm']
'mediatek,mt8173-disp-pwm' is not one of ['mediatek,mt8186-disp-pwm', 'mediatek,mt8188-disp-pwm', 'mediatek,mt8192-disp-pwm', 'mediatek,mt8195-disp-pwm', 'mediatek,mt8365-disp-pwm']
'mediatek,mt8173-disp-pwm' was expected
'mediatek,mt8183-disp-pwm' was expected
from schema $id: http://devicetree.org/schemas/pwm/mediatek,pwm-disp.yaml#
arch/arm64/boot/dts/mediatek/mt8173-elm.dtb: pwm@1401f000: compatible: 'oneOf' conditional failed, one must be fixed:
['mediatek,mt8173-disp-pwm', 'mediatek,mt6595-disp-pwm'] is too long
'mediatek,mt8173-disp-pwm' is not one of ['mediatek,mt6795-disp-pwm', 'mediatek,mt8167-disp-pwm']
'mediatek,mt8173-disp-pwm' is not one of ['mediatek,mt8186-disp-pwm', 'mediatek,mt8188-disp-pwm', 'mediatek,mt8192-disp-pwm', 'mediatek,mt8195-disp-pwm', 'mediatek,mt8365-disp-pwm']
'mediatek,mt8173-disp-pwm' was expected
'mediatek,mt8183-disp-pwm' was expected
from schema $id: http://devicetree.org/schemas/pwm/mediatek,pwm-disp.yaml#
Drop the extra "mediatek,mt6595-disp-pwm" compatible string.
Fixes: 61aee93425 ("arm64: dts: mt8173: add MT8173 display PWM driver support node")
Cc: YH Huang <yh.huang@mediatek.com>
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20250108083424.2732375-2-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b79fe18299 upstream.
In r852_ready(), the dev get from r852_get_dev() need to be checked.
An unstable device should not be ready. A proper implementation can
be found in r852_read_byte(). Add a status check and return 0 when it is
unstable.
Fixes: 50a487e771 ("mtd: rawnand: Pass a nand_chip object to chip->dev_ready()")
Cc: stable@vger.kernel.org # v4.20+
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d027951dc8 upstream.
In INFTL_findwriteunit(), the return value of inftl_read_oob()
need to be checked. A proper implementation can be
found in INFTL_deleteblock(). The status will be set as
SECTOR_IGNORE to break from the while-loop correctly
if the inftl_read_oob() fails.
Fixes: 8593fbc68b ("[MTD] Rework the out of band handling completely")
Cc: stable@vger.kernel.org # v2.6+
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21c02e8272 upstream.
Recently, during a debugging session using local MPTCP connections, I
noticed MPJoinAckHMacFailure was not zero on the server side. The
counter was in fact incremented when the PM rejected new subflows,
because the 'subflow' limit was reached.
The fix is easy, simply dissociating the two cases: only the HMAC
validation check should increase MPTCP_MIB_JOINACKMAC counter.
Fixes: 4cf8b7e48a ("subflow: introduce and use mptcp_can_accept_new_subflow()")
Cc: stable@vger.kernel.org
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250407-net-mptcp-hmac-failure-mib-v1-1-3c9ecd0a3a50@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 443041deb5 upstream.
When testing valkey benchmark tool with MPTCP, the kernel panics in
'mptcp_can_accept_new_subflow' because subflow_req->msk is NULL.
Call trace:
mptcp_can_accept_new_subflow (./net/mptcp/subflow.c:63 (discriminator 4)) (P)
subflow_syn_recv_sock (./net/mptcp/subflow.c:854)
tcp_check_req (./net/ipv4/tcp_minisocks.c:863)
tcp_v4_rcv (./net/ipv4/tcp_ipv4.c:2268)
ip_protocol_deliver_rcu (./net/ipv4/ip_input.c:207)
ip_local_deliver_finish (./net/ipv4/ip_input.c:234)
ip_local_deliver (./net/ipv4/ip_input.c:254)
ip_rcv_finish (./net/ipv4/ip_input.c:449)
...
According to the debug log, the same req received two SYN-ACK in a very
short time, very likely because the client retransmits the syn ack due
to multiple reasons.
Even if the packets are transmitted with a relevant time interval, they
can be processed by the server on different CPUs concurrently). The
'subflow_req->msk' ownership is transferred to the subflow the first,
and there will be a risk of a null pointer dereference here.
This patch fixes this issue by moving the 'subflow_req->msk' under the
`own_req == true` conditional.
Note that the !msk check in subflow_hmac_valid() can be dropped, because
the same check already exists under the own_req mpj branch where the
code has been moved to.
Fixes: 9466a1cceb ("mptcp: enable JOIN requests even if cookies are in use")
Cc: stable@vger.kernel.org
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Gang Yan <yangang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250328-net-mptcp-misc-fixes-6-15-v1-1-34161a482a7f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
