The Samsung Galaxy Book6 Pro (NP944XJG-KG4IT) exposes its SCAI ACPI
device with HID SAMB430, which is not in the driver's device ID table,
so the driver never binds and none of its features are available.
Add SAMB430 to galaxybook_device_ids[].
Tested on an NP944XJG-KG4IT by forcing the bind via driver_override,
which is equivalent to an ID table match. All driver features probe
successfully: keyboard backlight LED, battery charge control end
threshold, platform profile (low-power/quiet/balanced/performance),
firmware attributes (power_on_lid_open, usb_charging), and the camera
lens cover input switch.
One optional feature probe fails harmlessly on this model:
"failed to execute CSFI; device responded with failure code 0xff".
This does not affect any of the features listed above.
Assisted-by: Claude:claude-opus-5
Signed-off-by: Riccardo Squarcialupi <rikysquarcia@gmail.com>
Link: https://patch.msgid.link/20260731125431.199902-1-rikysquarcia@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The MSI-X path already flushes any posted MSI-X write before tearing down
its iATU mapping. That was added by commit c22533c66c ("PCI: dwc: ep:
Flush MSI-X write before unmapping its ATU entry") to make sure the write
reaches the Root Complex before the outbound window that translates it
disappears.
The MSI path has the same problem but no equivalent flush. When the
Endpoint driver caches an MSI target address and later observes that the
Root Complex has changed it, dw_pcie_ep_raise_msi_irq() unmaps the existing
iATU entry and reprograms it for the new address. Between the last MSI
writel() and the unmap there may still be a posted write sitting in the
fabric, and unmapping the iATU entry can drop or misroute that write.
Fix this by reading back from the mapped MSI window before the unmap. The
readback drains any posted MSI writes through the same iATU entry that
mapped them, which is the same logic the MSI-X path uses.
Fixes: 468711a40d ("PCI: dwc: ep: Refresh MSI Message Address cache on change")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/linux-pci/20260729214859.B9E2B1F00A3A@smtp.kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[mani: commit log]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Link: https://patch.msgid.link/20260730133123.1420413-5-cassel@kernel.org
The doorbell test case was observed to pass even when the Endpoint had
clearly failed to handle the doorbell trigger.
pci-endpoint-test 0000:01:00.0: Failed to trigger doorbell in endpoint
ok 23 pcie_ep_doorbell.DOORBELL_TEST
The root cause turned out to be a buggy EPC driver that raised two IRQs
in response to a single ENABLE DOORBELL command. The extra IRQ left
test->irq_raised.done at a non zero value, so the next
wait_for_completion_timeout() after the writel() that rings the
doorbell returned immediately, before the Endpoint had set
STATUS_DOORBELL_SUCCESS and raised the IRQ that belongs to that write.
The status readback that followed therefore did not yet reflect the
doorbell trigger, and the test logged the failure but did not fail the
test case. Later on, after the doorbell was disabled, the status was
read again and STATUS_DOORBELL_SUCCESS had by then been set by the
Endpoint for the earlier trigger. The final check saw the bit set and
reported the test as passed.
Make the trigger step actually fail the test case when it detects a
problem. Record the failure in a local variable, keep going so that
the doorbell is still disabled and the Endpoint is left in a clean
state, and return the stored error at the end. The disable path still
returns its own error immediately when its wait times out, which is
unchanged.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[mani: change log]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Link: https://patch.msgid.link/20260730122045.1382749-6-cassel@kernel.org
The Lenovo Yoga Book 9 14IAH10 ships with a detachable Bluetooth keyboard
that magnetically attaches to the bottom (secondary) screen in one of two
positions. The Embedded Controller tracks the attachment state in a 2-bit
field called BKBD and signals changes via WMI event GUID
806BD2A2-177B-481D-BFB5-3BA0BB4A2285 (notify ID 0xEB on the WM10 ACPI
device, _UID "GMZN").
The device contains embedded BMOF data (WQDD, 20705 bytes) documenting
both WMI interfaces used by this driver:
LENOVO_BTKBD_EVENT (event GUID): WmiDataId(1) uint32 Status.
The ACPI _WED(0xEB) method returns EC.BKBD directly as an integer,
so the notify callback receives BKBD without a separate query.
LENOVO_FEATURE_STATUS_DATA (block GUID, WQAF method): returns an
8-byte buffer {uint32 IDs=0x00060000, uint32 Status=BKBD}.
Used for the initial state read on probe and after resume.
BKBD encoding:
0 = keyboard detached
1 = keyboard docked on top half of bottom screen
2 = keyboard docked on bottom half of bottom screen
3 = reserved (not observed in practice)
This driver registers two WMI drivers sharing a module-level
BLOCKING_NOTIFIER_HEAD:
- The event driver (LENOVO_BTKBD_EVENT) uses .notify_new() to receive
a pre-parsed wmi_buffer and fires the notifier chain with the BKBD
value extracted from the buffer.
- The block driver (LENOVO_FEATURE_STATUS_DATA) owns the input_dev in
its per-device private struct. At probe time it registers a
notifier_block on the chain and reads the initial BKBD state via
wmidev_query_block(). The WMI buffer is parsed as
struct lenovo_feature_status { __le32 id; __le32 status; }, and the
ID field is verified before the status is used.
- SW_TABLET_MODE=1 is reported when the keyboard is detached;
SW_TABLET_MODE=0 when docked in either position (keyboard present).
- The raw BKBD value is exposed via read-only sysfs attribute
"keyboard_position".
- BKBD state is re-read via wmidev_query_block() on resume from
suspend or hibernation.
Tested on: Lenovo Yoga Book 9 14IAH10 (model 83KJ), kernel 7.0.
Acked-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Dave Carey <carvsdriver@gmail.com>
Link: https://patch.msgid.link/20260728225545.1333610-3-carvsdriver@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
* fix a regression caused by allowing coexistence of KHO with deferred
initialization of the memory map.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEeOVYVaWZL5900a/pOQOGJssO/ZEFAmpweGsACgkQOQOGJssO
/ZHe4gf/b06J+YW9GO7FGQclCf3s30DbL8nNeEkb74lpWU8CAfk2vbo9QyrlYH8+
5wtISj9+SdBwMfY4XFdDWOur1EHD47N52xbT5zL3yp1UEPpXYbggiiKuzwCXK1MZ
lVhyc3XfPmF4eRP5V0Nr7AsN1pAujH83uRrTgg//ZJziOaOtLi7ZWJZa0Oae3UY1
z+/bRIM21DzkL2wD2fitlYxYBmrooYRS6FVr+wv/khBnLxAtcWGM+nfHGI4/i4bK
5oz/9D3+nD/rQBqOT6F+Vf6Dz3zPtJPLe7+B459x24f2yPzJplIt6cDq9nxZKbY2
L7q3npvcsts7iLXVsKSeaHeEfn2l7g==
=xzQP
-----END PGP SIGNATURE-----
Merge tag 'liveupdate-fixes-2026-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/liveupdate/linux
Pull liveupdate fix from Mike Rapoport:
- fix a regression caused by allowing coexistence of KHO with deferred
initialization of the memory map
* tag 'liveupdate-fixes-2026-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/liveupdate/linux:
kho: align kho_scratch to MAX_ORDER_NR_PAGES pages
ksmbd_conn_handler_loop() caps a request from an unauthenticated
connection at SMB3_MAX_MSGSIZE, and only allows the larger
SMB3_MAX_MSGSIZE + conn->vals->max_write_size once the connection has
authenticated.
ksmbd_decompress_request() runs inside that same loop but applies the
authenticated limit unconditionally, and then allocates from it. The
unauthenticated cap is not re-applied afterwards, as the caller only
refreshes pdu_size from the new RFC1002 header.
An unauthenticated client that negotiates SMB 3.1.1 with a compression
context can therefore send a 104 byte chained transform whose
OriginalCompressedSegmentSize is SMB3_MAX_MSGSIZE + max_write_size and
have ksmbd kvmalloc() that much memory, 4210693 bytes by default. The
payload costs the client nothing, because a SMB3_COMPRESS_PATTERN
payload expands an eight byte structure into arbitrarily many output
bytes.
The decompressed PDU is rejected later by ksmbd_smb2_check_message(),
but that happens in the worker, after the allocation has been made and
conn->req_running has been incremented, and it results in an error
response rather than dropping the connection. A client that stops
reading its socket keeps each work queued for up to KSMBD_TCP_SEND_TIMEOUT
while ksmbd_conn_write() holds conn->srv_mutex, so the allocations
accumulate up to server_conf.max_inflight_req per connection.
Move the limit into ksmbd_max_allowed_pdu_size() and call it from both
sites, so the authentication state is consulted in one place and the two
ceilings cannot drift apart again.
Fixes: a08de24c2b ("ksmbd: negotiate and decode SMB2 compression")
Signed-off-by: Sujal Tuladhar <sujaltuladhar1231@gmail.com>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
ksmbd_decompress_request() allocated the decompressed request buffer
before smb_compression_decompress() rejected unknown transform Flags or
chained mode when it was not negotiated. A remote peer could force a
transient multi-megabyte allocation that was immediately freed on
-EINVAL.
Validate CHAINED/NONE Flags and compress_chained before kvmalloc.
Link: https://github.com/namjaejeon/ksmbd/issues/529
Fixes: a08de24c2b ("ksmbd: negotiate and decode SMB2 compression")
Signed-off-by: Anatolii Shumak <anatoliy.shumak@gmail.com>
Reviewed-by: ChenXiaoSong <chenxiaosong@kylinos.cn>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Pattern_V1 is an optional chained payload type selected during SMB 3.1.1
compression negotiate. conn->compress_pattern was only consulted when
building responses, so a peer that negotiated LZ77 with chained support
could still submit Pattern payloads on the receive path.
Pass allow_pattern through smb_compression_decompress() and reject
SMB3_COMPRESS_PATTERN in the chained decoder when it is false.
Link: https://github.com/namjaejeon/ksmbd/issues/529
Fixes: a08de24c2b ("ksmbd: negotiate and decode SMB2 compression")
Signed-off-by: Anatolii Shumak <anatoliy.shumak@gmail.com>
Reviewed-by: ChenXiaoSong <chenxiaosong@kylinos.cn>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
A remotely selected CPU can be re-advertised as idle by an idle-to-idle
re-pick before the BPF program validates the selection. Checking that
the selected CPU remains absent from the idle mask is therefore
inherently racy.
Validate a stable local invariant instead: a CPU executing
ops.select_cpu() or ops.enqueue() in a non-idle scheduling context must
not be advertised as idle. Read the idle mask without modifying it and
also validate selected CPUs against the requested domain and task
affinity.
Suggested-by: Kuba Piecuch <jpiecuch@google.com>
Signed-off-by: Andrea Righi <arighi@nvidia.com>
Reviewed-by: Kuba Piecuch <jpiecuch@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The built-in idle masks are reset with all online CPUs marked idle
before sched_ext is enabled. Busy CPUs can therefore be incorrectly
advertised as idle until their next idle transition.
Initialize the masks empty so that the initial state is conservative.
When bypass is lifted, every CPU is rescheduled and idle-to-idle
re-picks populate the masks with CPUs that are actually idle. Later
idle transitions keep the masks up to date.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrea Righi <arighi@nvidia.com>
Reviewed-by: Kuba Piecuch <jpiecuch@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The pci-epf driver sets STATUS_DOORBELL_ENABLE_SUCCESS as the final step of
pci_epf_test_enable_doorbell(), and STATUS_DOORBELL_DISABLE_SUCCESS as the
final step of pci_epf_test_disable_doorbell(). A missing SUCCESS bit
therefore unambiguously means that the operation did not complete, whereas
the FAIL bit is only set on an explicit failure path.
The host side test in pci_endpoint_test_doorbell() currently keys off
the FAIL bit. That covers explicit failures but misses two cases.
The first case is when the wait for the completion IRQ times out. No IRQ
arrives, the Endpoint never updates STATUS, and neither SUCCESS nor FAIL
is set. The enable path already handles this correctly because it also
fails when the wait times out without an IRQ. The disable path does not
have that extra guard and would wrongly treat the timeout as success.
The second is a buggy EPC that raises two IRQs in response to a single
DOORBELL_ENABLE command. The second wait_for_completion_timeout()
returns immediately with 'left' non zero, but the endpoint has not yet
written STATUS, so SUCCESS is clear and FAIL is also clear. The current
FAIL only check treats this as success.
So check the SUCCESS bit instead. That matches the Endpoint's contract
because SUCCESS is the last write on the success path, and it correctly
reports failure for both timeouts and the spurious IRQ case without
relying on the FAIL bit being set.
Fixes: eefb83790a ("misc: pci_endpoint_test: Add doorbell test case")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[mani: commit log]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Link: https://patch.msgid.link/20260730122045.1382749-5-cassel@kernel.org
The Yoga Book 9 14IAH10 (DMI product name "83KJ") has a dedicated
yb9-kbdock WMI driver that registers an input device reporting
SW_TABLET_MODE to track the detachable Bluetooth keyboard.
lenovo-ymc also loads on this machine and creates an input node with the
SW_TABLET_MODE capability bit set. For input switches, the presence of
the capability bit has semantic meaning: userspace (e.g. GNOME) reads
the switch state at startup from every node advertising the capability
and does not expect more than one such node.
Add a DMI match for the Yoga Book 9 14IAH10 to probe() so that
lenovo-ymc returns -ENODEV on this hardware, leaving yb9-kbdock as the
sole SW_TABLET_MODE source. The ymc_ec_trigger EC write, the only
other action taken in response to a YMC event, is guarded by a separate
DMI table that excludes this machine; no other functionality is affected.
Signed-off-by: Dave Carey <carvsdriver@gmail.com>
Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Link: https://patch.msgid.link/20260728225545.1333610-2-carvsdriver@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
- More lifecycle fixes for the new sub-scheduler support: a failed enable
could tear down a never-linked sub-scheduler in a way that races the root
scheduler's disable and leads to a use-after-free, tasks that were not on
the ext class could still get the enable callback, and a policy-rejection
path silently rewrote a running task's scheduling policy instead of
aborting the scheduler.
- Scheduler enable/disable could deadlock with cgroup removal and a
concurrent cgroup weight write through kernfs. Fixed by reordering lock
acquisition.
- Sync wakeups could leave the waker CPU incorrectly marked idle in the
built-in idle-CPU tracking.
- A selftest fix for sleeping tasks whose CPU affinity changes before
wakeup.
-----BEGIN PGP SIGNATURE-----
iIQEABYKACwWIQTfIjM1kS57o3GsC/uxYfJx3gVYGQUCam/mog4cdGpAa2VybmVs
Lm9yZwAKCRCxYfJx3gVYGe0NAQC2UrrXeSm97RTCv+5HBfom/8sjPdB2tiAwGiUt
fUUQ+AD9FP30urJaoiALUiL+EGWpLFejwUCXNXlT+0kN2TiFxQM=
=EuWf
-----END PGP SIGNATURE-----
Merge tag 'sched_ext-for-7.2-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext
Pull sched_ext fixes from Tejun Heo:
- More lifecycle fixes for the new sub-scheduler support: a failed
enable could tear down a never-linked sub-scheduler in a way that
races the root scheduler's disable and leads to a use-after-free,
tasks that were not on the ext class could still get the enable
callback, and a policy-rejection path silently rewrote a running
task's scheduling policy instead of aborting the scheduler.
- Scheduler enable/disable could deadlock with cgroup removal and a
concurrent cgroup weight write through kernfs. Fixed by reordering
lock acquisition.
- Sync wakeups could leave the waker CPU incorrectly marked idle in the
built-in idle-CPU tracking.
- A selftest fix for sleeping tasks whose CPU affinity changes before
wakeup.
* tag 'sched_ext-for-7.2-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext:
selftests/sched_ext: Handle sleeping task affinity changes in numa test
sched_ext: Mark waker CPU busy when selected in WAKE_SYNC case
sched_ext: Don't enable non-ext tasks in the sub-sched task loops
sched_ext: Skip sub-disable teardown for never-linked sub-schedulers
sched_ext: Take cgroup_lock() first in scx_cgroup_lock()
sched_ext: Reject setting disallow from init_task outside the enable path
The discard-block check in dm_integrity_rw_tag() treats a stored tag
of all 0xf6 bytes (DISCARD_FILLER) as proof a block was discarded and
skips HMAC verification. allow_discards is only accepted in
dm-integrity's standalone mode. An attacker with raw write access to
the backing device, but without the integrity key, can stamp any block
with an all-0xf6 tag and have it served as authentic.
Add a new "allow_discards_keyed" target argument that marks discarded
blocks with a keyed checksum of (salt || sector) instead, computed by
integrity_discard_checksum().
Fixes: 84597a44a9 ("dm integrity: add optional discard support")
Co-developed-by: Jo Van Bulck <jo.vanbulck@cs.kuleuven.be>
Signed-off-by: Jo Van Bulck <jo.vanbulck@cs.kuleuven.be>
Signed-off-by: Shukai Ni <shukai.ni@kuleuven.be>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Commit aeee55b76b ("regulator: ab8500: Remove unused embedded struct
expand_register") deleted the expand_register member from struct
ab8500_regulator_info and, in the same hunk, added an empty
"@expand_register:" line to the kernel-doc block. That traded one W=1
warning for another:
drivers/regulator/ab8500.c:196 Excess struct member 'expand_register'
description in 'ab8500_regulator_info'
Drop the leftover line; the remaining @member entries all match the
struct.
No functional changes.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/r/202605160857.ZIE3nO9J-lkp@intel.com/
Assisted-by: Claude:claude-opus-5 [kernel-doc]
Signed-off-by: Babanpreet Singh <bbnpreetsingh@gmail.com>
Link: https://patch.msgid.link/20260802013304.7-1-bbnpreetsingh@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct a few white-space issues, like missing space before bracket '{'
character or spurious space, which will be flagged by dt-check-style
("redundant-whitespace" warning). No functional changes.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260801210450.384087-4-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
Correct a few white-space issues, like double before bracket '{'
character, which will be flagged by dt-check-style
("redundant-whitespace" warning). No functional changes.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260801210450.384087-3-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
- A pressure trigger's poll timer could be re-armed while the last trigger
was being torn down and then fire after the cgroup was freed. Tie the
timer to the cgroup's lifetime and shut it down when the cgroup is freed.
- Writing to a pressure file forked a worker kthread while holding the
cgroup mutex, creating lock dependencies from the mutex to the whole fork
path. A pressure write racing a sched_ext scheduler enable, which blocks
forks before grabbing the mutex, deadlocked. Fork the worker with the
mutex dropped.
- Documentation fix for io.latency behavior on non-rotational devices.
-----BEGIN PGP SIGNATURE-----
iIQEABYKACwWIQTfIjM1kS57o3GsC/uxYfJx3gVYGQUCam/mlw4cdGpAa2VybmVs
Lm9yZwAKCRCxYfJx3gVYGVhRAQCyNBHCHpaY9erKTezenGDK6D+LqbfLWiWuIntB
swiwLQEA6h6Rgob2GDDRHOey7+XwF6PHh6xoh4FhSYboeEZd1wc=
=Re+7
-----END PGP SIGNATURE-----
Merge tag 'cgroup-for-7.2-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
- A pressure trigger's poll timer could be re-armed while the last
trigger was being torn down and then fire after the cgroup was freed.
Tie the timer to the cgroup's lifetime and shut it down when the
cgroup is freed.
- Writing to a pressure file forked a worker kthread while holding the
cgroup mutex, creating lock dependencies from the mutex to the whole
fork path. A pressure write racing a sched_ext scheduler enable,
which blocks forks before grabbing the mutex, deadlocked.
Fork the worker with the mutex dropped.
- Documentation fix for io.latency behavior on non-rotational devices.
* tag 'cgroup-for-7.2-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
Docs/admin-guide/cgroup-v2: document io.latency rotational vs non-rotational behavior
sched/psi: Shut down rtpoll_timer in psi_cgroup_free()
sched/psi: Create the psimon kthread outside of cgroup_mutex
The ShanWan Wireless Gamepad (dongle ID 2563:0575) crashes with a -71
EPROTO error during standard enumeration because it expects a 255-byte
initial configuration request. Add this device to the quirk list to
use the USB_QUIRK_WINDOWS_CONFIG_REQ_SIZE flag.
Signed-off-by: Ishaan Dandekar <ishaan.dandekar@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20260802120128.38302-1-ishaan.dandekar@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
announce_device() currently logs the device VID:PID and string
descriptors only after successful enumeration. This means that if
enumeration fails, no identifying information about the device appears
in the kernel log, making it difficult to diagnose failures.
Split announce_device() into announce_device_ids(), which logs the
VID:PID and bcdDevice immediately after the device descriptor is read,
and announce_device_strings(), which logs the product, manufacturer,
and serial number strings after successful enumeration. This ensures
that a device's identity is always visible in the log regardless of
whether enumeration succeeds or fails.
Suggested-by: Michal Pecio <michal.pecio@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Nikhil Solanke <nikhilsolanke5@gmail.com>
Link: https://patch.msgid.link/20260728195158.65162-3-nikhilsolanke5@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Certain third-party USB game controllers exposing (or spoofing) an Xbox
360-compatible interface (VID:PID 045e:028e) fail to enumerate under Linux.
The device disconnects from the bus without responding to the initial
GET_DESCRIPTOR(CONFIGURATION) request, and the kernel logs 'unable to read
config index 0 descriptor/start: -71'.
The device then falls back to a secondary Android HID mode (with a
different VID:PID), losing XInput functionality including rumble support.
The failure reproduces across multiple machines, host controller types, and
kernel versions including current mainline and LTS. The device enumerates
correctly and remains in XInput mode under Windows. Notably, the device
enumerates correctly in Android mode when the same 9-byte request
is issued for that mode's configuration descriptor, confirming the firmware
bug is specific to the XInput mode.
usbmon traces from Linux and Wireshark/USBPcap traces from Windows are
identical up to the point of failure, with no visible protocol-level
difference explaining the divergence. The root cause was identified when
Michal Pecio discovered via a QEMU bus-level capture that Windows does not
use wLength=9 for the initial config descriptor request; it uses
wLength=255. Alan Stern subsequently confirmed this with a bus
analyzer on a different USB 2.0 device, and Michal verified the behavior
goes back to Windows 95 OSR2.1.
So, add a new quirk flag USB_QUIRK_WINDOWS_CONFIG_REQ_SIZE which causes
usb_get_configuration() to issue a 255 byte sized configuration request
instead of USB_DT_CONFIG_SIZE (9) for the initial
GET_DESCRIPTOR(CONFIGURATION) request, mimicking long-standing Windows
behavior.
This patch intentionally does not add any new VID:PID entries using this
quirk. Some affected Xbox 360-compatible controllers spoof Microsoft's
VID:PID, while genuine Microsoft controllers already enumerate correctly
and do not require this quirk. Other affected clone devices use their own
VID:PID pairs and can be added individually as they are identified.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Michal Pecio <michal.pecio@gmail.com>
Closes: https://lore.kernel.org/linux-usb/CAFgddh+JWdT4LLwMc5qjM8q_pBu-fRo2qADR5ovAKoGHWMQrRw@mail.gmail.com/
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Nikhil Solanke <nikhilsolanke5@gmail.com>
Link: https://patch.msgid.link/20260728195158.65162-2-nikhilsolanke5@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If cxacru_cm() encounters an error while submitting or waiting for snd_urb,
it aborts and returns the error without killing the already submitted
rcv_urb. This leaves the rcv_urb active.
When this happens during initialization (e.g., in cxacru_atm_start()), the
driver may ignore the error and proceed to call cxacru_poll_status(), which
invokes cxacru_cm() again. Attempting to submit the still-active rcv_urb
triggers a warning in usb_submit_urb():
cxacru 1-1:1.0: send of cm 0x84 failed (-104)
ATM dev 0: cxacru_atm_start: CHIP_ADSL_LINE_START returned -104
------------[ cut here ]------------
URB ffff88812658d200 submitted while active
WARNING: drivers/usb/core/urb.c:379 at usb_submit_urb+0x79/0x18b0
drivers/usb/core/urb.c:379
...
Call Trace:
<TASK>
cxacru_cm+0x21a/0xf10 drivers/usb/atm/cxacru.c:631
cxacru_cm_get_array drivers/usb/atm/cxacru.c:722 [inline]
cxacru_poll_status+0x178/0x1110 drivers/usb/atm/cxacru.c:828
cxacru_atm_start+0x185/0x360 drivers/usb/atm/cxacru.c:814
usbatm_atm_init+0x144/0x3a0 drivers/usb/atm/usbatm.c:927
usbatm_usb_probe+0x15cb/0x1db0 drivers/usb/atm/usbatm.c:1178
cxacru_usb_probe+0x17f/0x220 drivers/usb/atm/cxacru.c:1370
...
To fix this, ensure that rcv_urb is properly killed if cxacru_cm() aborts
early. We can safely call usb_kill_urb() on rcv_urb in the error path, as
it is safe to call even if the URB is not active (e.g., if it failed to
submit in the first place, or if it already completed).
Fixes: 1b0e614652 ("[PATCH] USB ATM: driver for the Conexant AccessRunner chipset cxacru")
Cc: stable <stable@kernel.org>
Assisted-by: Gemini:gemini-3.5-flash Gemini:gemini-3.1-pro-preview syzbot
Reported-by: syzbot+c9dff578c3a41775176a@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=c9dff578c3a41775176a
Link: https://syzkaller.appspot.com/ai_job?id=75fec6f2-c8a6-43b1-b184-4d26baba86cc
Signed-off-by: Aleksandr Nogikh <nogikh@google.com>
Link: https://patch.msgid.link/91edfa4c-a63d-400c-9f00-31f3e1f98c00@mail.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ibuf_len is the bulk IN (receive) buffer size, but the EMSGSIZE check
in usbio_bulk_msg() compares it against txbuf_len — the bulk OUT
endpoint size. Both are taken independently from different endpoints
in usbio_probe(), so the check is wrong when they differ.
Use rxbuf_len for the IN direction. This matches the buffer that
actually holds the response data.
Fixes: 121a0f839d ("usb: misc: Add Intel USBIO bridge driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Jiangshan Yi <yijiangshan@kylinos.cn>
Tested-by: Antti Laakso <antti.laakso@linux.intel.com>
Link: https://patch.msgid.link/20260722101810.458634-1-yijiangshan@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable ndp_index is declared as a signed integer, but it stores
the return value of get_ncm(), which is unsigned.
A malicious host can supply a large offset that overflows the signed
ndp_index, making it negative. Because ndp_index is compared against
unsigned bounds, this negative value bypasses sanity checks and leads
to an out-of-bounds read when calculating the address of the NDP
block (ntb_ptr + ndp_index).
Fix this by changing ndp_index to unsigned int to ensure consistent
unsigned comparisons throughout the function.
Fixes: 370af734df ("usb: gadget: NCM: RX function support multiple NDPs")
Cc: stable <stable@kernel.org>
Signed-off-by: Sonali Pradhan <sonalipradhan@google.com>
Link: https://patch.msgid.link/20260720165654.2224591-1-sonalipradhan@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
readl() already returns a CPU-endian value. Passing its return value to
le32_to_cpu() is therefore redundant and causes an incorrect double byte
swap on big-endian systems.
Similarly, writel() expects a CPU-endian value, so passing the result of
cpu_to_le32() is incorrect.
Remove the unnecessary conversions and operate on the MMIO register value
as a CPU-endian u32.
Fixes: 241e2ce88e ("usb: cdnsp: Fix issue with resuming from L1")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20260720-endian-fix-v1-v1-1-b5681fa1ea9f@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If creating a protected vCPU in kvm_s390_pv_create_cpu() fails,
kvm_s390_pv_destroy_cpu() was called, which checks whether the vCPU has
a PV handle and exits doing nothing otherwise. At that point, due to
not having created the protected vCPU, the PV handle will not be set,
and kvm_s390_pv_destroy_cpu() will do nothing, thus leaking the
allocated memory.
Fix by factoring out the code to free and reset a PV vCPU; call it from
kvm_s390_pv_destroy_cpu() and kvm_s390_pv_create_cpu().
Opportunistically fix the return value of kvm_s390_pv_destroy_cpu() in
case of errors: return -EIO instead if EIO.
Fixes: d4074324b0 ("KVM: s390: pv: avoid double free of sida page")
Reviewed-by: Steffen Eiden <seiden@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Message-ID: <20260803124040.126471-14-imbrenda@linux.ibm.com>
imx_uart_probe() publishes its devm-allocated port in imx_uart_ports[]
before uart_add_one_port() because console setup uses the table. The entry
is not cleared when adding the port fails or after removal, leaving a
dangling pointer.
A sibling probe can register the shared console through that stale entry.
This was reproduced under KASAN on QEMU mcimx6ul-evk by unbinding a
sibling UART, unbinding the console UART and rebinding the sibling.
Keep the entry valid through uart_remove_one_port(), then clear it. Protect
port addition and removal together with their table updates so sibling
operations cannot interleave. Reject an occupied slot rather than
clobbering an active port during a duplicate-line probe.
Fixes: dbff4e9ea2 ("IMX UART: remove statically initialized tables")
Fixes: 9f322ad064 ("imx: serial: handle initialisation failure correctly")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Link: https://lore.kernel.org/all/20260719162850.043B41F000E9@smtp.kernel.org
Link: https://lore.kernel.org/all/20260719222501.CB4CB1F000E9@smtp.kernel.org
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-fable-5
Signed-off-by: Karl Mehltretter <kmehltretter@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260731181844.11330-6-kmehltretter@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_cdev_add() drops the cdev reference when cdev_add() fails, but
leaves driver->cdevs[index] pointing to freed memory.
tty_unregister_device() later passes that stale pointer to cdev_del(),
causing a use-after-free.
Clear the slot after dropping the reference.
Fixes: c1a752ba2d ("tty: don't leak cdev in tty_cdev_add()")
Assisted-by: Claude:claude-fable-5
Signed-off-by: Karl Mehltretter <kmehltretter@gmail.com>
Link: https://patch.msgid.link/20260731181844.11330-5-kmehltretter@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TTY device registration can fail before a cdev is allocated.
Serial core keeps the port so setserial can still use it, and later
removal passes the NULL cdev slot to cdev_del(), causing a NULL-pointer
dereference.
Only delete the cdev when the slot is not NULL.
Fixes: a3a10ce342 ("Avoid usb reset crashes by making tty_io cdevs truly dynamic")
Fixes: da4c279942 ("serial: enable serdev support")
Assisted-by: Claude:claude-fable-5
Signed-off-by: Karl Mehltretter <kmehltretter@gmail.com>
Link: https://patch.msgid.link/20260731181844.11330-4-kmehltretter@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_register_driver() leaves drv->state pointing to freed memory when
tty_alloc_driver() fails. If tty_register_driver() fails, drv->tty_driver
also retains a pointer after its reference is dropped.
Drivers that use drv->state as an "already registered" flag can then skip
registration on the next probe and pass the freed state to
uart_add_one_port().
This issue was found with failslab on QEMU's raspi1ap board by
failing registration and binding the PL011 port again.
Clear both pointers on their failure paths, as uart_unregister_driver()
already does.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Fixes: 9e845abfc8 ("serial: fix NULL pointer dereference")
Assisted-by: Claude:claude-fable-5
Signed-off-by: Karl Mehltretter <kmehltretter@gmail.com>
Link: https://patch.msgid.link/20260731181844.11330-3-kmehltretter@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial_core_add_one_port() allocates uport->tty_groups after
uart_configure_port(), which may register the console. If the allocation
fails, the driver unwinds the port while its console remains registered.
The earlier uport->name allocation has a related failure path that leaves
state->uart_port linked to a port being freed.
Failslab reproduced a NULL dereference in PL011 console output and a KASAN
use-after-free in i.MX console output after failed binds.
Allocate the name and tty_groups before linking the port and configuring
it. Reserve space for the optional driver attribute group because
config_port() may populate uport->attr_group during configuration.
Fixes: 266dcff03e ("Serial: allow port drivers to have a default attribute group")
Fixes: f7048b1590 ("tty: serial_core: Add name field to uart_port struct")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/all/20260719070454.D6FA21F000E9@smtp.kernel.org/
Assisted-by: Claude:claude-fable-5
Signed-off-by: Karl Mehltretter <kmehltretter@gmail.com>
Link: https://patch.msgid.link/20260731181844.11330-2-kmehltretter@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MUEx50 UART exposes a programmable RX trigger level via the RTL
register.
Implement uart_port RX trigger set/get callbacks for the mxpcie driver
and wire them up to the generic rx_trig_bytes sysfs interface. Store the
configured trigger level in the per-port private data.
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-15-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a private per-port data structure for the mxpcie driver and
replace the shared flexible array of registered lines with an array of
per-port objects.
This prepares the driver for storing per-port state needed by subsequent
features.
No functional change intended.
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-14-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rx_trig_bytes sysfs attribute currently relies on 8250-internal
helper functions and assumes a fixed mapping between trigger levels and
FIFO behavior.
Some UARTs provide hardware-specific RX trigger mechanisms that do not
fit this model. Add optional uart_port callbacks for setting and getting
the RX trigger level, and use them when provided, while preserving the
existing 8250 helpers as the default fallback.
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-13-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On MUEx50, break signaling under RS485 requires a driver-specific
sequence and cannot be handled correctly by the generic 8250 break
implementation alone.
Implement a mxpcie break_ctl callback that performs MUEx50-specific
break handling when RS485 is enabled and fall back to the default 8250
break handling for other modes.
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-12-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some UARTs require driver-specific handling for break signaling, which
cannot be expressed by the generic 8250 break implementation alone.
Add an optional uart_port break_ctl callback and route
serial8250_break_ctl() through it when provided. Rename the existing
8250 implementation to serial8250_do_break_ctl() and export it so
low-level drivers can reuse the default 8250 behavior when appropriate.
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-11-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moxa PCIe multiport serial boards support switching the serial interface
mode between RS232, RS422, RS485-2W, and RS485-4W via on-board control
registers.
Implement an rs485_config() callback and map TIOCSRS485 requests to the
corresponding hardware modes using serial_rs485 flags:
- RS232 = (no flags set)
- RS422 = SER_RS485_ENABLED | SER_RS485_MODE_RS422
- RS485_2W (half-duplex) = SER_RS485_ENABLED
- RS485_4W (full-duplex) = SER_RS485_ENABLED | SER_RS485_RX_DURING_TX
This allows users to reconfigure the serial mode at runtime via ioctl().
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-10-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MUEx50 UART provides a memory-mapped TX FIFO data window along with
a TX FIFO level counter.
Fill the TX FIFO in bulk via the MMIO FIFO window based on available
FIFO space, using uart_port_tx_limited() for the common serial-core TX
handling.
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-9-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MUEx50 UART provides a memory-mapped RX FIFO data window along with
an RX FIFO byte counter.
When no break or error conditions are present, read received data in
bulk via the MMIO FIFO window and push it to the tty layer in one
operation. Fall back to the generic 8250 RX path for break and error
handling.
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-8-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a mxpcie-specific handle_irq() implementation for Moxa PCIe serial
ports.
This keeps the interrupt handling self-contained in the driver and
provides a hook point for MUEx50-specific RX/TX paths added in subsequent
patches. The handler processes RX, updates modem status, and handles TX
when THRE is asserted.
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-7-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MUEx50 UART can handle in-band software flow control (XON/XOFF)
directly in hardware.
Program the on-chip XON/XOFF characters from termios settings and enable
the corresponding MUEx50 flow control modes when IXON or IXOFF is
requested. Provide throttle and unthrottle callbacks so RX can be
stopped and resumed cleanly.
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-6-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MUEx50 UART supports automatic RTS/CTS flow control via the enhanced
feature register.
Implement a mxpcie-specific set_termios() callback that enables MUEx50
auto-RTS/auto-CTS when CRTSCTS is requested and disables it otherwise.
Keep the 8250 port status flags in sync with the hardware configuration.
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-5-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MUEx50 UART provides an enhanced register set and programmable FIFO
trigger levels for RX, TX, and flow control.
Enable enhanced mode during port startup and program the MUEx50 FIFO
trigger registers according to the configured port settings. Clear the
programmed state again during shutdown to restore the default UART
configuration.
The TX FIFO write pointer and read pointer are driven by different
clocks. Clear the FIFOs repeatedly during startup so both pointers are
reset before programming the trigger levels.
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-4-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new 8250 port type for the Moxa MUEx50 UART and describe its basic
FIFO size and trigger characteristics in the 8250 port configuration
table.
The 8250_mxpcie driver sets UPF_FIXED_TYPE and uses PORT_MUEX50 so that
the generic 8250 core applies the correct defaults.
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-3-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Moxa PCIe multiport serial boards are currently handled as part of
8250_pci.c. In preparation for adding Moxa-specific UART features and
optimizations, move the Moxa PCIe implementation into a dedicated
driver.
This introduces drivers/tty/serial/8250/8250_mxpcie.c and wires it up
via Kconfig and Makefile, while preserving the existing probe flow and
device IDs.
This change was suggested during earlier reviews by Andy Shevchenko [1][2].
No functional change intended.
Link: https://lore.kernel.org/all/ZmQovC6TbDpTb3c8@surfacebook.localdomain/ [1]
Link: https://lore.kernel.org/all/CAHp75VeDsVt0GQYUFxLM+obfmqXBPa3hM3YMsFbc26uzWZG-SQ@mail.gmail.com/ [2]
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://patch.msgid.link/20260731074820.735619-2-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When adding a new vCPU to the SCA area, the validity bit in the MCN was
set before the pointer to the state description, potentially allowing
for a race.
Fix by setting the pointer before setting the bit.
Fixes: 14542a0a54 ("KVM: S390: Remove sca_lock")
Reviewed-by: Steffen Eiden <seiden@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Message-ID: <20260803124040.126471-13-imbrenda@linux.ibm.com>
If a fatal signal is pending while trying to fault-in a page, return
-EINTR instead of -EAGAIN.
Also fix unpack_one() to handle -EINTR properly.
Fixes: e907ae5301 ("KVM: s390: Add helper functions for fault handling")
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Message-ID: <20260803124040.126471-12-imbrenda@linux.ibm.com>
The mmu cache is the first thing that is allocated in
kvm_arch_vcpu_create(), but in case of failure it was not freed.
Fix by freeing the mmu cache in case of failure.
Refactor kvm_arch_vcpu_create() to use scope-based cleanup instead of
gotos.
Fixes: e38c884df9 ("KVM: s390: Switch to new gmap")
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Message-ID: <20260803124040.126471-11-imbrenda@linux.ibm.com>
gmap_remove_child() needs to be called while holding the children_lock
of the parent gmap. This was not the case in the error handling path of
kvm_arch_vcpu_create() for UCONTROL guests.
Fix by adding the missing lock.
Fixes: e38c884df9 ("KVM: s390: Switch to new gmap")
Reviewed-by: Steffen Eiden <seiden@linux.ibm.com>
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Message-ID: <20260803124040.126471-10-imbrenda@linux.ibm.com>
When a memslot is removed, all ptes that mapped the slot are cleared or
even deallocated. If this happens while the system is in migration
mode, and if cmma-dirty pages are removed, the cmma-dirty counter will
not reflect reality.
Fix by appropriately decrementing the cmma-dirty counter when removing
a memslot.
Opportunistically improve kvm_arch_commit_memory_region() to use
__free() for the struct kvm_s390_mmu_cache.
Fixes: e38c884df9 ("KVM: s390: Switch to new gmap")
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Message-ID: <20260803124040.126471-9-imbrenda@linux.ibm.com>
