rtl8723be hw_init() calls local_save_flags(flags) followed by
local_irq_enable(). Later, local_irq_restore(flags) is called.
This causes warnings from Lockdep on boot and modprobe,
as local_irq_restore(flags) should only be called while irqs are disabled.
The warning was introduced to detect this class of bug in [1].
With testing I found that all paths which call hw_init() have irqs
already enabled for rtl8723be.
Furthermore, the calls were originally added for the rtl8192ce
in commit f78bccd79b ("rtlwifi: rtl8192ce: Fix too long disable of IRQs")
before later being added to most other rtlwifi drivers.
Commit d3feae41a3 ("rtlwifi: Update power-save routines for 062814 driver")
then replaces the call to spin_lock_irqsave() before hw_init(),
and thus the codepath which caused irqs to be disabled in hw_init and
prompted the original commit has been removed.
The same irq save/restore pattern is also present in the hw_init() of
rtl8192ce, rtl8723ae, rtl8188ee, rtl8192se and rtl8192cu,
however I don't have the hardware to test them,
so I did not include them in my changes.
Tested on a Razer Blade 14 2017.
Example of output from Lockdep prior to fix:
raw_local_irq_restore() called with IRQs enabled
...
Call Trace:
<TASK>
rtl8723be_hw_init+0x5992/0x7220 [rtl8723be]
? static_obj+0x61/0xa0
rtl_pci_start+0x222/0x5c0 [rtl_pci]
rtl_op_start+0x128/0x1a0 [rtlwifi]
? __kasan_check_read+0x11/0x20
drv_start+0x16c/0x550 [mac80211]
...
irq event stamp: 887679
hardirqs last enabled at (887689): [<ffffffff96511170>] __up_console_sem+0x90/0xa0
hardirqs last disabled at (887698): [<ffffffff96511155>] __up_console_sem+0x75/0xa0
softirqs last enabled at (887670): [<ffffffff962f4675>] __irq_exit_rcu+0x175/0x2f0
softirqs last disabled at (887649): [<ffffffff962f4675>] __irq_exit_rcu+0x175/0x2f0
---[ end trace 0000000000000000 ]---
[1] https://lore.kernel.org/all/20210111153707.10071-1-mark.rutland@arm.com/
Signed-off-by: William Hansen-Baird <william.hansen.baird@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260609095359.2964193-1-william.hansen.baird@gmail.com
This > comparison should be >= to avoid an out of bounds access.
Fixes: 419ed7f4a0 ("wifi: rtw89: debug: extend bb_info with TX status and PER")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/aia25i0ds3B6QF6c@stanley.mountain
The format of scan offload v2 is to extend fields to consider channel
noise as a factor to adjust dwell time of certain channels. Leave empty
for now to ignore this factor.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260525070735.27659-3-pkshih@realtek.com
The firmware features including version of command/event format are
maintained by this table, which enables features by firmware version.
Define the first feature set accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260525070735.27659-2-pkshih@realtek.com
This module is now orphaned code, superseded by a kernel-global
implementation, so remove it.
Reviewed-by: Eliot Courtney <ecourtney@nvidia.com>
Acked-by: Danilo Krummrich <dakr@kernel.org>
Link: https://patch.msgid.link/20260701-nova-bitfield-v2-2-2e949bf1836c@nvidia.com
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
- Fix racy bitfield updates in vfio-pci-core and the mlx5 vfio-pci
variant driver with a binary split between setup/release and
runtime modified flags. These were noted across several Sashiko
reviews as pre-existing issues. (Alex Williamson)
- Fix runtime PM inconsistency where the vfio-pci driver module_init
could modify the idle PM policy of existing devices through globals
managed in vfio-pci-core, leading to unbalanced runtime PM
operations. (Alex Williamson)
- Restore mutability of writable vfio-pci module options by further
pulling policy globals out of vfio-pci-core, to instead be latched
per device at device init. Provide visibility of the per device
latched values through debugfs. (Alex Williamson)
- Fix missing VGA arbiter uninit callback in unwind path.
(Alex Williamson)
- Reorder device debugfs removal before device_del() to avoid gap
where debugfs is available with stale devres pointers.
(Alex Williamson)
- Move UUID library linking flag from vfio selftest Makefile into
libvfio.mk to avoid exposing such dependencies when linking with
KVM selftests. (Sean Christopherson)
-----BEGIN PGP SIGNATURE-----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=V/L3
-----END PGP SIGNATURE-----
Merge tag 'vfio-v7.2-rc2' of https://github.com/awilliam/linux-vfio
Pull VFIO fixes from Alex Williamson:
"Mostly straightforward fixes here, inconsistent runtime PM handling
due to global device policies, bitfield races, unwind path gaps,
teardown ordering, and a misplaced library flag.
- Fix racy bitfield updates in vfio-pci-core and the mlx5 vfio-pci
variant driver with a binary split between setup/release and
runtime modified flags. These were noted across several Sashiko
reviews as pre-existing issues (Alex Williamson)
- Fix runtime PM inconsistency where the vfio-pci driver module_init
could modify the idle PM policy of existing devices through globals
managed in vfio-pci-core, leading to unbalanced runtime PM
operations (Alex Williamson)
- Restore mutability of writable vfio-pci module options by further
pulling policy globals out of vfio-pci-core, to instead be latched
per device at device init. Provide visibility of the per device
latched values through debugfs (Alex Williamson)
- Fix missing VGA arbiter uninit callback in unwind path (Alex
Williamson)
- Reorder device debugfs removal before device_del() to avoid gap
where debugfs is available with stale devres pointers (Alex
Williamson)
- Move UUID library linking flag from vfio selftest Makefile into
libvfio.mk to avoid exposing such dependencies when linking with
KVM selftests (Sean Christopherson)"
* tag 'vfio-v7.2-rc2' of https://github.com/awilliam/linux-vfio:
vfio: selftests: Add luuid to libvfio.mk's list of libraries, not to the Makefile
vfio/pci: Expose latched module parameter policy in debugfs
vfio: Remove device debugfs before releasing devres
vfio/pci: Latch all module parameters per device
vfio/mlx5: Fix racy bitfields and tighten struct layout
vfio/pci: Fix racy bitfields and tighten struct layout
vfio/pci: Release the VGA arbiter client on register_device() failure
vfio/pci: Latch disable_idle_d3 per device
Syzbot reported list corruption caused by a double list_add_tail() call on
bh->b_assoc_buffers within nilfs_lookup_dirty_data_buffers().
Analysis revealed that the root cause was the insertion of a page/folio
with a page index of ULONG_MAX into the page cache via the GC ioctl.
filemap_get_folios_tag(), called by nilfs_lookup_dirty_data_buffers(),
repeatedly detects a dirty folio with a page index of ULONG_MAX due to
index wrap-around, leading to duplicate processing of dirty buffers.
As a preparatory step, the GC ioctl loads the page/folio of the block to
be moved during GC and inserts it into the page cache based on information
in the nilfs_vdesc structure passed as an argument. Normally, this does
not cause issues because the user-space GC library configures the
nilfs_vdesc structure properly. However, since there is no range check on
the parameters determining the page index, a request with artificially
crafted parameters -- such as those generated by Syzbot -- can result in a
page/folio being inserted with a page index of ULONG_MAX, triggering the
above problem.
This resolves the issue by checking the ranges of 'vd_offset' and
'vd_vblocknr' in the nilfs_vdesc structure that determine the page index,
thereby preventing the invalid page/folio insertions.
Reported-by: syzbot+c37bed40868932d790e9@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=c37bed40868932d790e9
Fixes: 7942b919f7 ("nilfs2: ioctl operations")
Cc: wuyankun <wuyankun@uniontech.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
- Fix potential null pointer dereference in dma-buf.
- Handle 0 in dma_fence_dedup_array.
- Use the correct callback in dma_fence_timeline_name.
- Fix device removal handling in amdxdna.
- kernel-doc fixes.
- Include header fix for drm_ras.h
- Handle edids better in virtio.
- Use the clk_bulk api for error handling in malidp.
- More clk handling fixes for komeda.
- panthor scheduler block fallout fixes.
- panthor unplug fixes.
- other panthor fixes.
- Fix unnecessary WARN_ON in topology probe after teardown.
- Add refcount to amdxdna job to fix use-after free.
- Fix increasing args->size in ioctl's of drm/imagination.
- Handle stride correctly in pvr_set_uobj_array.
- Only call imagination's drm_sched_entity_fini once.
-----BEGIN PGP SIGNATURE-----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=heUt
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2026-07-02' of https://gitlab.freedesktop.org/drm/misc/kernel into drm-fixes
drm-misc-fixes for v7.2-rc2:
- Fix potential null pointer dereference in dma-buf.
- Handle 0 in dma_fence_dedup_array.
- Use the correct callback in dma_fence_timeline_name.
- Fix device removal handling in amdxdna.
- kernel-doc fixes.
- Include header fix for drm_ras.h
- Handle edids better in virtio.
- Use the clk_bulk api for error handling in malidp.
- More clk handling fixes for komeda.
- panthor scheduler block fallout fixes.
- panthor unplug fixes.
- other panthor fixes.
- Fix unnecessary WARN_ON in topology probe after teardown.
- Add refcount to amdxdna job to fix use-after free.
- Fix increasing args->size in ioctl's of drm/imagination.
- Handle stride correctly in pvr_set_uobj_array.
- Only call imagination's drm_sched_entity_fini once.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patch.msgid.link/786bdc92-0ce3-4c0f-9668-b0fa8a0047ea@linux.intel.com
- Wedge from the timeout handler only after releasing the queue (Rodrigo)
- Fix a NULL pointer dereference (Francois)
- Remove redundant exec_queue_suspended (Lu)
- RTP / OA whitelist fixes (Ashutosh, Gustavo, Thomas)
- Return error on non-migratable faults requiring devmem (Matt Brost)
- Skip FORCE_WC and vm_bound check for external dma-bufs (Matt Auld)
- Hold notifier lock for write on inject test path (Shuicheng)
- Drop bogus static from finish in force_invalidate (Shuicheng)
- Fix double-free of managed BO in error path (Shuicheng)
- Don't attempt to process FAST_REQ or EVENT relays (Michal)
- Fix NPD in bo_meminfo (Matthew Auld)
- Prevent invalid cursor access for purged BOs (Matthew Auld)
- Fix offset alignment for MERT WHITELST_OA_MERT_MMIO_TRG (Ashutosh)
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRskUM7w1oG5rx2IZO4FpNVCsYGvwUCakZ+rgAKCRC4FpNVCsYG
v4rdAQDvkckFMQCZ04RHhJk3SDR4hkPU3rjSHRkaujMCIBdBVAD7BfNkWzeNE+ht
xn5jI7MPDtdyLu7MQtWoqzA7rTwAdgM=
=soS7
-----END PGP SIGNATURE-----
Merge tag 'drm-xe-fixes-2026-07-02' of https://gitlab.freedesktop.org/drm/xe/kernel into drm-fixes
Driver Changes:
- Wedge from the timeout handler only after releasing the queue (Rodrigo)
- Fix a NULL pointer dereference (Francois)
- Remove redundant exec_queue_suspended (Lu)
- RTP / OA whitelist fixes (Ashutosh, Gustavo, Thomas)
- Return error on non-migratable faults requiring devmem (Matt Brost)
- Skip FORCE_WC and vm_bound check for external dma-bufs (Matt Auld)
- Hold notifier lock for write on inject test path (Shuicheng)
- Drop bogus static from finish in force_invalidate (Shuicheng)
- Fix double-free of managed BO in error path (Shuicheng)
- Don't attempt to process FAST_REQ or EVENT relays (Michal)
- Fix NPD in bo_meminfo (Matthew Auld)
- Prevent invalid cursor access for purged BOs (Matthew Auld)
- Fix offset alignment for MERT WHITELST_OA_MERT_MMIO_TRG (Ashutosh)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Hellstrom <thomas.hellstrom@linux.intel.com>
Link: https://patch.msgid.link/akZ_UbrL94G4F2iA@fedora
Building the rseq selftests against musl libc fails because musl's
<features.h> does not provide the glibc-specific __GNUC_PREREQ macro:
error: missing binary operator before token '('
Replace __GNUC_PREREQ(11, 1) with an equivalent check using __GNUC__
and __GNUC_MINOR__ directly. This pattern is portable across all C
library implementations and is already used elsewhere in the tools/
tree (e.g., tools/include/linux/string.h).
This also allows removing the #include <features.h>, which was only
needed for __GNUC_PREREQ.
Fixes: 886ddfba93 ("selftests/rseq: Introduce thread pointer getters")
Signed-off-by: Hisam Mehboob <hisamshar@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20260618193724.589113-2-hisamshar@gmail.com
On multi-tile platforms, we need to probe the hardware for the number
of tiles that are present in the platform. That means that we should
do that as part of xe_probe_info() instead of xe_info_init(). Do
that.
Reviewed-by: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com>
Reviewed-by: Violet Monti <violet.monti@intel.com>
Link: https://patch.msgid.link/20260609-xe-probe-info-v1-9-21e83e188e60@intel.com
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
The value of xe->info.tile_count is only really valid after
xe_info_probe_tile_count(). Any use of tile_count before that point
is invalid and, consequently, initializing it in xe_info_init_early()
is pointless.
Move the initialization to xe_info_probe_tile_count().
Reviewed-by: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com>
Reviewed-by: Violet Monti <violet.monti@intel.com>
Link: https://patch.msgid.link/20260609-xe-probe-info-v1-8-21e83e188e60@intel.com
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
On GMDID-based platforms, the driver needs to probe the hardware by
reading GMDID registers in order to identify the
graphics/media/display IPs that are present in the platform as well as
their stepping values.
Currently, xe_info_init() has such a probing logic, but that task
should be rather responsibility of xe_probe_info(). As such, move it
to the latter.
For pre-GMDID platforms, the IPs are identified via PCI devid and
revid fields, which is arguably also hardware dependent. So do the
same for those platforms.
Reviewed-by: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com>
Reviewed-by: Violet Monti <violet.monti@intel.com>
Link: https://patch.msgid.link/20260609-xe-probe-info-v1-7-21e83e188e60@intel.com
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Currently the logic to set the graphics step for non-GMDID-based
platforms in kunit testing is defined in xe_wa_test_init(). That
logic should rather belong to the helper xe_pci_fake_device_init(), so
move it there.
Reviewed-by: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com>
Reviewed-by: Violet Monti <violet.monti@intel.com>
Link: https://patch.msgid.link/20260609-xe-probe-info-v1-6-21e83e188e60@intel.com
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
The platform-level step information depends on the PCI revid and, as
such, should be probed in xe_probe_info_early() instead of
xe_info_init_early(). Move the code accordingly.
Note that we currently only update probed_info->step.platform as part
of this change. We will deal with the other fields of
probed_info->step as a follow-up change, which will be tied to the
probing of graphics and media IPs.
Reviewed-by: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com>
Reviewed-by: Violet Monti <violet.monti@intel.com>
Link: https://patch.msgid.link/20260609-xe-probe-info-v1-5-21e83e188e60@intel.com
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Currently xe_step_platform_get() uses info fields from xe->info to
define the platform-level stepping value.
Because the platform-level stepping info depends on the PCI revid, it
should be defined as part of xe_probe_info_early() instead of being
directly probed inside xe_info_init_early().
Let's make sure that xe_step_platform_get() receives the necessary
data as parameters and does not depend on xe->info. That will allow
us to move the call up to xe_probe_info_early() in an upcoming change.
Reviewed-by: Violet Monti <violet.monti@intel.com>
Link: https://patch.msgid.link/20260609-xe-probe-info-v1-4-21e83e188e60@intel.com
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
The PCI devid and revid fields are info that we probe from the
hardware (indirectly via the PCI subsystem). Add them to
xe_probed_info and set them via xe_probe_info_early(), since the
respective fields in xe->info are updated in xe_info_init_early().
Reviewed-by: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com>
Reviewed-by: Violet Monti <violet.monti@intel.com>
Link: https://patch.msgid.link/20260609-xe-probe-info-v1-3-21e83e188e60@intel.com
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
The xe_step_*_get() functions update the step directly in
xe->info.step and are called by functions xe_info_init_early() and
xe_info_init().
As the stepping info is something probed from the hardware (via PCI
revid and/or GMDID) and we want to move away from probing inside
xe_info_init*() functions, let's make xe_step_*_get() functions modify
a pointer to the step structure instead of modifying xe->info.step
directly: this will allow an upcoming change that will move those
function calls out of the info init functions and will pass a member
of struct xe_probed_info instead of xe->info.step.
Reviewed-by: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com>
Reviewed-by: Violet Monti <violet.monti@intel.com>
Link: https://patch.msgid.link/20260609-xe-probe-info-v1-2-21e83e188e60@intel.com
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Functions xe_info_init_early() and xe_info_init() currently probe some
information from the hardware while doing initialization of info
fields. Besides mixing responsibilities, another issue from this
approach is that kunit tests need to implement static stubs for the
probing part.
Let's prepare the ground to ensuring that those functions stop probing
the information from the hardware by creating the necessary framework
for extracting the probing bits out of them. Do that by creating a
new struct type called xe_probed_info and the functions responsible
for populating it.
In upcoming changes, we will gradually refactor the code so that all
info needed by xe_info_init_early() and xe_info_init() that is probed
from the hardware is passed to them via struct xe_probed_info.
Reviewed-by: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com>
Reviewed-by: Violet Monti <violet.monti@intel.com>
Link: https://patch.msgid.link/20260609-xe-probe-info-v1-1-21e83e188e60@intel.com
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
The syscall trace path reloads syscall arguments from pt_regs before
calling the syscall handler. On C-SKY ABIv2, the 5th and 6th syscall
arguments are prepared as stack arguments before invoking syscallid.
The current code adjusts sp before loading LSAVE_A4 and LSAVE_A5. Since
those offsets are relative to the original pt_regs base, loading them
after changing sp fetches the wrong slots. As a result, traced syscalls
that use the 5th or 6th argument may receive corrupted arguments.
This is visible with mmap2(), which takes six arguments. A small
PTRACE_SYSCALL reproducer opens a file and maps one page with:
mmap(NULL, 4096, PROT_READ | PROT_EXEC, MAP_PRIVATE, fd, 0)
Before the fix, the traced child fails the mmap and exits with 12.
After the fix, the mapping succeeds and the child exits with 0.
Fix the trace path by loading a4/a5 from pt_regs before changing sp.
Tested on: ck860f, linux-4.19.15, C-SKY abiv2
Fixes: e0bbb53843 ("csky: Fixup abiv2 syscall_trace break a4 & a5")
Suggested-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Hanlin Song <pgeorge8929@gmail.com>
Signed-off-by: Guo Ren (Alibaba DAMO Academy) <guoren@kernel.org>
In ATH11K_QMI_EVENT_FW_READY, ATH11K_FLAG_REGISTERED is set
unconditionally even when ath11k_core_qmi_firmware_ready() fails.
This leaves the driver in an inconsistent state where
initialization is considered complete although the firmware ready
handling did not finish successfully. During the subsequent SSR,
the driver enters the restart path based on this incorrect state
and dereferences uninitialized srng members, resulting in a NULL
pointer dereference.
Call trace:
ath11k_hal_srng_access_begin+0xc/0x60 [ath11k] (P)
ath11k_ce_cleanup_pipes+0x17c/0x180 [ath11k]
ath11k_core_restart+0x40/0x168 [ath11k]
Fix this by:
- skipping firmware_ready if ATH11K_FLAG_REGISTERED is already set
- setting ATH11K_FLAG_REGISTERED only when firmware_ready succeeds
- setting ATH11K_FLAG_QMI_FAIL and aborting the FW_READY handling
on error
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.2.0.c2-00204-QCAMSLSWPLZ-1
Fixes: 6fe62a8cec ("wifi: ath11k: Add cold boot calibration support on WCN6750")
Signed-off-by: Gaole Zhang <gaole.zhang@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260609090609.4041009-1-gaole.zhang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The aggr_reset_state() function uses timer_delete() (non-synchronous)
for the aggregation timer before proceeding to delete TID state and
before the structure is freed by callers like aggr_module_destroy().
If the timer callback (aggr_timeout) is executing when aggr_reset_state()
is called, the callback will continue to access aggr_conn fields like
rx_tid[] and stat[] which may be freed immediately after by
kfree(aggr_info->aggr_conn) in aggr_module_destroy().
Additionally, the timer callback can re-arm itself via mod_timer() while
aggr_reset_state() is running, creating a more complex race condition.
Use timer_delete_sync() instead to ensure any running timer callback
has completed before returning.
Fixes: bdcd817079 ("Add ath6kl cleaned up driver")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Hodges <git@danielhodges.dev>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20260206185207.30098-1-git@danielhodges.dev
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath9k_hif_request_firmware() re-arms an asynchronous firmware load via
request_firmware_nowait(), passing hif_dev as the completion context, and
then still dereferences hif_dev:
dev_info(&hif_dev->udev->dev, "ath9k_htc: Firmware %s requested\n",
hif_dev->fw_name);
The re-armed callback ath9k_hif_usb_firmware_cb() runs on the "events"
workqueue and, when the firmware is missing, walks the retry chain into
ath9k_hif_usb_firmware_fail() -> complete_all(&hif_dev->fw_done). That
releases the wait_for_completion(&hif_dev->fw_done) in a concurrent
ath9k_hif_usb_disconnect(), which then kfree()s hif_dev. The trailing
dev_info() in the frame that re-armed the request can therefore read freed
memory (hif_dev->udev, the first field of struct hif_device_usb):
BUG: KASAN: slab-use-after-free in ath9k_hif_request_firmware
Read of size 8 ... by task kworker/...
ath9k_hif_request_firmware
ath9k_hif_usb_firmware_cb drivers/net/wireless/ath/ath9k/hif_usb.c:1247
request_firmware_work_func
Allocated by ...:
ath9k_hif_usb_probe drivers/net/wireless/ath/ath9k/hif_usb.c
Freed by ...:
ath9k_hif_usb_disconnect -> kfree drivers/net/wireless/ath/ath9k/hif_usb.c
The fw_done barrier only makes disconnect wait for the firmware chain to
*terminate*; it does not protect the outer ath9k_hif_request_firmware()
frame that re-armed the request and keeps touching hif_dev afterwards.
Drop the post-request dev_info(): it is the only use of hif_dev after the
async request is armed, and it is purely informational (the dev_err() on the
failure path runs only when request_firmware_nowait() did not arm a callback,
so hif_dev is still alive there).
This was first reported by syzbot as a single, non-reproduced crash that was
later auto-obsoleted, and was independently rediscovered by the reFuzz fuzzer,
which produced a C reproducer (USB-gadget connect/disconnect of an ath9k_htc
device whose firmware download fails). The vulnerable code is unchanged and
still present in v7.1-rc6, where the slab-use-after-free reproduces under KASAN
once the (sub-microsecond) race window is widened.
Fixes: e904cf6fe2 ("ath9k_htc: introduce support for different fw versions")
Reported-by: syzbot+50122cbc2874b1eb25b0@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=50122cbc2874b1eb25b0
Signed-off-by: Cheng Yongkang <teel4res@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20260605153210.20471-1-1020691186@qq.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Fix "concelable" -> "cancelable" in the comment above
io_uring_cmd_mark_cancelable(), and fix the memory ordering comment
in __io_uring_cmd_done() to reference io_do_iopoll() and
->iopoll_completed.
Signed-off-by: Yang Xiuwei <yangxiuwei@kylinos.cn>
Link: https://patch.msgid.link/20260702082937.3707134-3-yangxiuwei@kylinos.cn
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The commit cited below should not have been merged. It attemted to fix an
existing problem ansd thereby introduced new problems by keeping the
pi_state in state Q_REQUEUE_PI_IN_PROGRESS and leaking it.
Based on the commit description the intention was to handle the case
when task_blocks_on_rt_mutex() returns -EDEADLK and the following
remove_waiter() dereferences the NULL pointer in waiter->task.
That is already handled by Davidlohr in commit 40a25d59e8
("locking/rtmutex: Skip remove_waiter() when waiter is not enqueued") and
requires no further acting.
Revert the commit breaking the "waiter == owner" case again.
Fixes: 74e144274a ("futex/requeue: Prevent NULL pointer dereference in remove_waiter() on self-deadlock")
Reported-by: Michael Bommarito <michael.bommarito@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260701131150.0Ijhq4Dw@linutronix.de
Closes: https://lore.kernel.org/all/20260629020049.2082397-1-michael.bommarito@gmail.com
inv_icm45600_buffer_fifo_read() uses the FIFO_COUNT the device reports,
unclamped, as the length of a regmap_noinc_read() into the fixed
INV_ICM45600_FIFO_SIZE_MAX (8 KiB) st->fifo.data buffer. The only bound is
the caller's "max", which the interrupt path skips (it passes 0). A device,
or an attacker on the bus, reporting up to 65535 makes the read as large as
~1 MiB: a heap out-of-bounds write of device-controlled data.
Clamp st->fifo.count to the buffer capacity before the read, and allocate
the buffer with the same INV_ICM45600_FIFO_SIZE_MAX define, so the bound
and the allocation reference one constant. The clamp is a no-op for
conforming hardware.
Signed-off-by: Bryam Vargas <hexlabsecurity@proton.me>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver currently exposes the IIO device to userspace before
completing sensor hub callback registration, and similarly removes
callbacks while the device can still be accessed during teardown.
This creates a timing window where userspace may enable the buffer
before callbacks are available. In such cases:
- samples can be dropped,
- buffered reads may observe stale or no data.
Reorder probe and remove paths to ensure callbacks are active before
device exposure and are removed after device is no longer accessible.
This avoids a race window leading to data loss.
Signed-off-by: Sanjay Chitroda <sanjayembeddedse@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver currently exposes the IIO device to userspace before
completing sensor hub callback registration, and similarly removes
callbacks while the device can still be accessed during teardown.
This creates a timing window where userspace may enable the buffer
before callbacks are available. In such cases:
- samples can be dropped,
- buffered reads may observe stale or no data.
Reorder probe and remove paths to ensure callbacks are active before
device exposure and are removed after device is no longer accessible.
This avoids a race window leading to data loss.
Signed-off-by: Sanjay Chitroda <sanjayembeddedse@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver currently exposes the IIO device to userspace before
completing sensor hub callback registration, and similarly removes
callbacks while the device can still be accessed during teardown.
This creates a timing window where userspace may enable the buffer
before callbacks are available. In such cases:
- samples can be dropped,
- buffered reads may observe stale or no data.
Reorder probe and remove paths to ensure callbacks are active before
device exposure and are removed after device is no longer accessible.
This avoids a race window leading to data loss.
Signed-off-by: Sanjay Chitroda <sanjayembeddedse@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver currently exposes the IIO device to userspace before
completing sensor hub callback registration, and similarly removes
callbacks while the device can still be accessed during teardown.
This creates a timing window where userspace may enable the buffer
before callbacks are available. In such cases:
- samples can be dropped,
- buffered reads may observe stale or no data.
Reorder probe and remove paths to ensure callbacks are active before
device exposure and are removed after device is no longer accessible.
This avoids a race window leading to data loss.
Signed-off-by: Sanjay Chitroda <sanjayembeddedse@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver currently exposes the IIO device to userspace before
completing sensor hub callback registration, and similarly removes
callbacks while the device can still be accessed during teardown.
This creates a timing window where userspace may enable the buffer
before callbacks are available. In such cases:
- samples can be dropped,
- buffered reads may observe stale or no data.
Reorder probe and remove paths to ensure callbacks are active before
device exposure and are removed after device is no longer accessible.
This avoids a race window leading to data loss.
Signed-off-by: Sanjay Chitroda <sanjayembeddedse@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver currently exposes the IIO device to userspace before
completing sensor hub callback registration, and similarly removes
callbacks while the device can still be accessed during teardown.
This creates a timing window where userspace may enable the buffer
before callbacks are available. In such cases:
- samples can be dropped,
- buffered reads may observe stale or no data.
Reorder probe and remove paths to ensure callbacks are active before
device exposure and are removed after device is no longer accessible.
This avoids a race window leading to data loss.
Signed-off-by: Sanjay Chitroda <sanjayembeddedse@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver currently exposes the IIO device to userspace before
completing sensor hub callback registration, and similarly removes
callbacks while the device can still be accessed during teardown.
This creates a timing window where userspace may enable the buffer
before callbacks are available. In such cases:
- samples can be dropped,
- buffered reads may observe stale or no data.
Reorder probe and remove paths to ensure callbacks are active before
device exposure and are removed after device is no longer accessible.
This avoids a race window leading to data loss.
Signed-off-by: Sanjay Chitroda <sanjayembeddedse@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver currently exposes the IIO device to userspace before
completing sensor hub callback registration, and similarly removes
callbacks while the device can still be accessed during teardown.
This creates a timing window where userspace may enable the buffer
before callbacks are available. In such cases:
- samples can be dropped,
- buffered reads may observe stale or no data.
Reorder probe and remove paths to ensure callbacks are active before
device exposure and are removed after device is no longer accessible.
This avoids a race window leading to data loss.
Signed-off-by: Sanjay Chitroda <sanjayembeddedse@gmail.com>
Fixes: fc18dddc06 ("iio: hid-sensors: Added device rotation support")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The RB5gen2 is an embedded development platform for the
QCS8550, based on the Snapdragon 8 Gen 2 SoC (SM8550).
This change implements the main board, the vision mezzanine
will be supported in a follow up patch.
The main board has the following features:
- Qualcomm Dragonwing QCS8550 SoC
- Adreno GPU 740
- Spectra ISP
- Adreno VPU 8550
- Adreno DPU 1295
- 1 x 1GbE Ethernet (USB Ethernet)
- WIFI 7 + Bluetooth 5.4
- 1 x USB 2.0 Micro B (Debug)
- 1 x USB 3.0 Type C (ADB, DP out)
- 2 x USB 3.0 Type A
- 1 x HDMI 1.4 Type A
- 1 x DP 1.4 Type C
- 2 x WSA8845 Speaker amplifiers
- 2 x Speaker connectors
- 1 x On Board PDM MIC
- Accelerometer + Gyro Sensor
- 96Boards compatible low-speed and high-speed connectors [1]
- 7 x LED indicators (4 user, 2 radio, 1 power)
- Buttons for power, volume up/down, force USB boot
- 3 x Dip switches
On-Board PMICs:
- PMK8550 2.1
- PM8550 2.0
- PM8550VS 2.0 x4
- PM8550VE 2.0
- PM8550B 2.0
- PMR735D 2.0
- PM8010 1.1 x2
Product Page: [2]
[1] https://www.96boards.org/specifications/
[2] https://www.thundercomm.com/product/qualcomm-rb5-gen-2-development-kit
The default msi-map from sm8550.dtsi is deleted for both pcie0 and
pcie1. The QPS615 PCIe switch on each port exposes more than two
devices (1 USP + 3 DSPs), but Gunyah currently limits ITS device
mappings to two per root complex to save memory. With msi-map
present, the ITS MAPD command times out.
Deleting msi-map causes the DWC controller to fall back to its
internal iMSI-RX module, which handles MSIs without this limitation.
Signed-off-by: Joe Sandom <jsandom@axon.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260420-rb5gen2-dts-v4-5-b461909c2de8@axon.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Move qcom,gsi-loader and memory-region properties from individual board
DTS files into the SoC DTSI, since these are common to all SM8550-based
boards.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Joe Sandom <jsandom@axon.com>
Link: https://lore.kernel.org/r/20260420-rb5gen2-dts-v4-3-b461909c2de8@axon.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add labels to the root port nodes (pcie0_port0, pcie1_port0) to
allow board DTS files to reference them for adding endpoint devices
to each pcie root port.
Update the pcieport0 reference to pcie0_port0 in sm8550-hdk.dts and
sm8550-qrd.dts to match the label rename in sm8550.dtsi.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Joe Sandom <jsandom@axon.com>
Link: https://lore.kernel.org/r/20260420-rb5gen2-dts-v4-2-b461909c2de8@axon.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the MHI register regions to the pcie0 and pcie1 controller nodes
to expose link power state transition counters (L0s/L1/L1.1/L1.2/L2)
via debugfs. The PCIe host driver uses this region to read the
link_transition_count from the MHI registers.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Joe Sandom <jsandom@axon.com>
Link: https://lore.kernel.org/r/20260420-rb5gen2-dts-v4-1-b461909c2de8@axon.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add an IMEM on glymur which falls back to mmio-sram and define the
PIL relocation info region as its child, for post mortem tools to
locate the loaded remoteprocs.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Ananthu C V <ananthu.cv@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260424-glymur-imem-v5-2-18ede63cf063@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add compatible for Qualcomm's glymur IMEM, a block of sram which
can fall back to mmio-sram.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Ananthu C V <ananthu.cv@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260424-glymur-imem-v5-1-18ede63cf063@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the mode-switch property to the QMP combo PHY so that mode-switch
events are routed to it, allowing the PHY to enter DisplayPort Alternate
Mode. Expand the DP data-lanes assignment from two to four lanes to make
use of the full link bandwidth available in this configuration.
Signed-off-by: Mahadevan P <mahadevan.p@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260420-kodiak_4k-v1-1-83dfc66b8f06@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable secondary USB controller in host mode on lemans EVK Platform.
Secondary USB controller is connected to a Genesys Logic USB HUB GL3590
having 4 ports. The ports of hub that are present on lemans EVK standalone
board are used as follows:-
1) port-1 is connected to HD3SS3220 Type-C port controller.
2) port-4 is used for the M.2 E key on corekit. Standard core kit uses UART
for Bluetooth. This port is to be used only if user optionally replaces the
WiFi card with the NFA765 chip which uses USB for Bluetooth.
Remaining 2 ports will become functional when the interface plus mezzanine
board is stacked on top of corekit:
3) port-2 is connected to another hub which is present on the mezz through
which 4 type-A ports are connected.
4) port-3 is used for the M.2 B key for a 5G card when the mezz is
connected.
Secondary USB Controller
↓
GL3590 USB Hub (4 ports)
|
|-- Port 1 → HD3SS3220 Type‑C Port Controller → USB‑C Connector
|
|-- Port 2 → Mezzanine USB Hub (when mezz attached)
|
|-- Port 3 → M.2 B‑Key Slot (when mezz attached)
|
|-- Port 4 → M.2 E‑Key Slot
(Default: BT via UART;
USB only if NFA765 module is installed)
Mark the second USB controller as host only capable and add the HD3SS3220
Type-C port controller along with Type-C connector for controlling vbus
supply.
Signed-off-by: Swati Agarwal <swati.agarwal@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260406110113.1709886-3-swati.agarwal@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Rename the hd3ss3220_ instance to improve clarity and simplify usage when
adding a secondary port controller.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Swati Agarwal <swati.agarwal@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260406110113.1709886-2-swati.agarwal@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the Cypress USB Type-C controller and associated connector.
The controller is connected over I2C12 and wired to the USB1 DWC3.
The USB-C connector routes both high-speed and super-speed signals.
Enable dual-role data and power over the USB-C connector.
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260421101606.411335-1-loic.poulain@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
