The double `the' is duplicated in the comment, remove one.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The double `is' is duplicated in the comment, remove one.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The double `for' is duplicated in the comment, remove one.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace 'the the' with 'the' in the comment.
[hverkuil: the the -> that the]
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace 'the the' with 'the' in the comment.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace 'the the' with 'the' in the comment.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace 'the the' with 'the' in the comment.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace 'the the' with 'the' in the comment.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace 'the the' with 'the' in the comment.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace 'the the' with 'the' in the comment.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace 'the the' with 'the' in the comment.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The double `the' is duplicated in the comment, remove one.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The double `this' is duplicated in line 3215, remove one.
[hverkuil: while we're at it, fix the 'succedeed' typo as well]
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Remove the repeated ',' from string
Signed-off-by: Li zeming <zeming@nfschina.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a V4L2 mem-to-mem driver for the Vivante DW100 Dewarp Processor IP
core found on i.MX8MP SoC.
The processor core applies a programmable geometrical transformation on
input images to correct distorsion introduced by lenses.
The transformation function is exposed as a grid map with 16x16 pixel
macroblocks indexed using X, Y vertex coordinates.
The dewarping map can be set from application through a dedicated v4l2
control. If not set or invalid, the driver computes an identity map
prior to starting the processing engine.
The driver supports scaling, cropping and pixel format conversion.
Signed-off-by: Xavier Roumegue <xavier.roumegue@oss.nxp.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The DW100 driver gets the dewarping mapping as a binary blob from the
userspace application through a custom control.
The blob format is hardware specific so create a dedicated control for
this purpose.
Signed-off-by: Xavier Roumegue <xavier.roumegue@oss.nxp.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a control base for DW100 driver controls, and reserve 16 controls.
Signed-off-by: Xavier Roumegue <xavier.roumegue@oss.nxp.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add user documentation for the DW100 driver.
while at it, replace spaces with tab on drivers list.
Signed-off-by: Xavier Roumegue <xavier.roumegue@oss.nxp.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Export the callback functions of the default v4l2 control type operations
such as a driver defining its own operations could reuse some of them.
Signed-off-by: Xavier Roumegue <xavier.roumegue@oss.nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Initializing arrays and validating or checking for equality of arrays
is suboptimal since it does this per element.
Change the ops to operate on the whole payload to speed up array
operations.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
works perfectly with:
modprobe ftdi_sio
echo "0590 00b2" | tee
/sys/module/ftdi_sio/drivers/usb-serial\:ftdi_sio/new_id > /dev/null
but doing this every reboot is a pain in the ass.
Signed-off-by: Niek Nooijens <niek.nooijens@omron.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Return value from devm_snd_soc_register_component() directly
instead of taking this in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Jinpeng Cui <cui.jinpeng2@zte.com.cn>
Link: https://lore.kernel.org/r/20220829091319.266068-1-cui.jinpeng2@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
The RTCCTRL reg of LS1C is obselete.
Writing this reg will cause system hang.
Fixes: 60219c563c ("MIPS: Add RTC support for Loongson1C board")
Signed-off-by: Yang Ling <gnaygnil@gmail.com>
Tested-by: Keguang Zhang <keguang.zhang@gmail.com>
Acked-by: Keguang Zhang <keguang.zhang@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Sync drm-intel-next with v6.0-rc as well as recent drm-intel-gt-next.
Since drm-next does not have commit f0c70d41e4 ("drm/i915/guc: remove
runtime info printing from time stamp logging") yet, only
drm-intel-gt-next, will need to do that as part of the merge here to
build.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Remove the module parameters for configuring GuC log size.
We should instead rely on tuning the defaults to be usable for
reporting bugs.
v2:
- Use correct 1M unit
Fixes: 8ad0152afb ("drm/i915/guc: Make GuC log sizes runtime configurable")
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Alan Previn <alan.previn.teres.alexis@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220826092343.184568-1-joonas.lahtinen@linux.intel.com
Sebastian Andrzej Siewior says:
====================
net: u64_stats fixups for 32bit.
while looking at the u64-stats patch
https://lore.kernel.org/all/20220817162703.728679-10-bigeasy@linutronix.de
I noticed that u64_stats_fetch_begin() is used. That suspicious thing
about it is that network processing, including stats update, is
performed in NAPI and so I would expect to see
u64_stats_fetch_begin_irq() in order to avoid updates from NAPI during
the read. This is only needed on 32bit-UP where the seqcount is not
used. This is address in 2/2. The remaining user take some kind of
precaution and may use u64_stats_fetch_begin().
I updated the previously mentioned patch to get rid of
u64_stats_fetch_begin_irq(). If this is not considered stable patch
worthy then it can be ignored and considred fixed by the other series
which removes the special 32bit cases.
The xrs700x driver reads and writes the counter from preemptible context
so the only missing piece here is at least disable preemption on the
writer side to avoid preemption while the writer is in progress. The
possible reader would spin then until the writer completes its write
critical section which is considered bad. This is addressed in 1/2 by
using u64_stats_update_begin_irqsave() and so disable interrupts during
the write critical section.
The other closet resemblance I found is mdio_bus.c::mdiobus_stats_acct()
where preemtion is disabled unconditionally. This is something I want to
avoid since it also affects 64bit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On 32bit-UP u64_stats_fetch_begin() disables only preemption. If the
reader is in preemptible context and the writer side
(u64_stats_update_begin*()) runs in an interrupt context (IRQ or
softirq) then the writer can update the stats during the read operation.
This update remains undetected.
Use u64_stats_fetch_begin_irq() to ensure the stats fetch on 32bit-UP
are not interrupted by a writer. 32bit-SMP remains unaffected by this
change.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Catherine Sullivan <csully@google.com>
Cc: David Awogbemila <awogbemila@google.com>
Cc: Dimitris Michailidis <dmichail@fungible.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jeroen de Borst <jeroendb@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Simon Horman <simon.horman@corigine.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: oss-drivers@corigine.com
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xrs700x_read_port_counters() updates the stats from a worker using the
u64_stats_update_begin() version. This is okay on 32-UP since on the
reader side preemption is disabled.
On 32bit-SMP the writer can be preempted by the reader at which point
the reader will spin on the seqcount until writer continues and
completes the update.
Assigning the mib_mutex mutex to the underlying seqcount would ensure
proper synchronisation. The API for that on the u64_stats_init() side
isn't available. Since it is the only user, just use disable interrupts
during the update.
Use u64_stats_update_begin_irqsave() on the writer side to ensure an
uninterrupted update.
Fixes: ee00b24f32 ("net: dsa: add Arrow SpeedChips XRS700x driver")
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Casper Andersson says:
====================
net: sparx5: add mrouter support
This series adds support for multicast router ports to SparX5. To manage
mrouter ports the driver must keep track of mdb entries. When adding an
mrouter port the driver has to iterate over all mdb entries and modify
them accordingly.
v2:
- add bailout in free_mdb
- re-arrange mdb struct to avoid holes
- change devm_kzalloc -> kzalloc
- change GFP_ATOMIC -> GFP_KERNEL
- fix spelling
====================
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All multicast should be forwarded to mrouter ports. Mrouter ports must
therefore be part of all active multicast groups, and override flooding
from being disabled.
Signed-off-by: Casper Andersson <casper.casan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep track of all mdb entries in software for easy access.
Signed-off-by: Casper Andersson <casper.casan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP multicast must sometimes be discriminated from non-IP multicast,
e.g. when determining the forwarding behavior of a given group in the
presence of multicast router ports on an offloaded bridge. Therefore,
provide helpers to identify these groups.
Signed-off-by: Casper Andersson <casper.casan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had historically not checked that genlmsghdr.reserved
is 0 on input which prevents us from using those precious
bytes in the future.
One use case would be to extend the cmd field, which is
currently just 8 bits wide and 256 is not a lot of commands
for some core families.
To make sure that new families do the right thing by default
put the onus of opting out of validation on existing families.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Paul Moore <paul@paul-moore.com> (NetLabel)
Signed-off-by: David S. Miller <davem@davemloft.net>
Despite the name, R-Car V3U is the first member of the R-Car Gen4
family. Hence move its compatible value to the R-Car Gen4 section.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220824094327.33685-4-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We have a cross dependency between KVM and VFIO when using
s390 vfio_pci_zdev extensions for PCI passthrough
To be able to keep both subsystem modular we add a registering
hook inside the S390 core code.
This fixes a build problem when VFIO is built-in and KVM is built
as a module.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Fixes: 09340b2fca ("KVM: s390: pci: add routines to start/stop interpretive execution")
Cc: <stable@vger.kernel.org>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/20220819122945.9309-1-pmorel@linux.ibm.com
Message-Id: <20220819122945.9309-1-pmorel@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Keep regulators as individual devices. There is no need to have them
under simple bus. This will throw compilation warnings like:
- unnecessary #address-cells/#size-cells without "ranges" or child "reg"
property.
- node has a unit name, but no reg or ranges property.
While at it move it down a bit in the file to keep entries sorted
alphabetically.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-10-claudiu.beznea@microchip.com
Add basic support for pcb8290. It has 2 lan8814 phys(each phy is a
quad-port) on the external MDIO bus and no SFP ports.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220825065135.1075049-1-horatiu.vultur@microchip.com
On the Radxa ROCK3 Model A the I2C adapters related to the MIPI DSI
connector and the M.2/NGFF connector use the non-default pins.
Specify the correct pinctrl but leave the adapters disabled (as
they are supposed to be activated by overlays that describe the
external hardware).
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20220712133204.2524942-3-michael.riesch@wolfvision.net
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Radxa ROCK3 Model A features a voltage regulator that provides
a 3V3 supply to the MIPI DSI connector. Add this regulator to the
device tree of the board.
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20220712133204.2524942-2-michael.riesch@wolfvision.net
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Radxa ROCK3 Model A features a voltage regulator that provides
a 3V3 supply to the MIPI CSI connector. Add this regulator to the
device tree of the board.
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20220712133204.2524942-1-michael.riesch@wolfvision.net
Signed-off-by: Heiko Stuebner <heiko@sntech.de>