Allow to configure port split options using the devlink port split
interface. Support port splitting only for port 0, as the FW has
a predefined set of available port split options for the whole device.
Add ice_devlink_port_options_print() function to print the table with
all available FW port split options. It will be printed after each port
split and unsplit command.
Add documentation for devlink port split interface usage for the ice
driver.
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_nvm_write_activate function is used to issue AdminQ command
0x0707 which sends a request to firmware to activate a flash bank. For
basic operations, this command takes an 8bit flag value which defines
the flags to control the activation process. There are some additional
flags that are stored in a second 8bit flag field.
We can simplify the interface by using a u16 cmd_flags variable. Split
this over the two bytes of flag storage in the structure.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement support for Get/Set Port Options admin queue commands
(0x06EA/0x06EB). These firmware commands allow the driver to change port
specific options and will be used in the next patch.
Co-developed-by: Lev Faerman <lev.faerman@intel.com>
Signed-off-by: Lev Faerman <lev.faerman@intel.com>
Co-developed-by: Damian Milosek <damian.milosek@intel.com>
Signed-off-by: Damian Milosek <damian.milosek@intel.com>
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support for parsing TTL and ToS (Hop Limit and Traffic Class) tc fields
and matching on those fields in filters. Incomplete part of implementation
was already in place (getting enc_ip and enc_tos from flow_match_ip and
writing them to filter header).
Note: matching on ipv6 ip_ttl, enc_ttl and enc_tos is currently not
supported by the DDP package.
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
cpumask related files are listed under the BITMAP API section, so the
file with tests for cpumask should be added to that list.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Reviewed-by: David Gow <davidgow@google.com>
Acked-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
The cpumask test suite doesn't follow the KUnit style guidelines, as
laid out in Documentation/dev-tools/kunit/style.rst. The file is
renamed to lib/cpumask_kunit.c to clearly distinguish it from other,
non-KUnit, tests.
Link: https://lore.kernel.org/lkml/346cb279-8e75-24b0-7d12-9803f2b41c73@riseup.net/
Suggested-by: Maíra Canal <mairacanal@riseup.net>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Reviewed-by: David Gow <davidgow@google.com>
Acked-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Since cpumask_first() on the cpu_possible_mask must return at most
nr_cpu_ids - 1 for a valid result, cpumask_last() cannot return anything
larger than this value. As test_cpumask_weight() also verifies that the
total weight of cpu_possible_mask must equal nr_cpu_ids, the last bit
set in this mask must be at nr_cpu_ids - 1.
Fixes: c41e8866c2 ("lib/test: introduce cpumask KUnit test suite")
Link: https://lore.kernel.org/lkml/346cb279-8e75-24b0-7d12-9803f2b41c73@riseup.net/
Reported-by: Maíra Canal <mairacanal@riseup.net>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Maíra Canal <mairacanal@riseup.net>
Reviewed-by: David Gow <davidgow@google.com>
Acked-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
When the number of CPUs that can possibly be brought online is known at
boot time, e.g. when HOTPLUG is disabled, nr_cpu_ids may be smaller than
NR_CPUS. In that case, cpu_possible_mask would not be completely filled,
and cpumask_full(cpu_possible_mask) can return false for valid system
configurations.
Without this test, cpu_possible_mask contents are still constrained by
a check on cpumask_weight(), as well as tests in test_cpumask_first(),
test_cpumask_last(), test_cpumask_next(), and test_cpumask_iterators().
Fixes: c41e8866c2 ("lib/test: introduce cpumask KUnit test suite")
Link: https://lore.kernel.org/lkml/346cb279-8e75-24b0-7d12-9803f2b41c73@riseup.net/
Reported-by: Maíra Canal <mairacanal@riseup.net>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Maíra Canal <mairacanal@riseup.net>
Reviewed-by: David Gow <davidgow@google.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
There are opcodes that need ->async_data only in some cases and
allocation it unconditionally may hurt performance. Add an option to
opdef to make move the allocation part from the core io_uring to opcode
specific code.
Note, we can't just set opdef->async_size to zero because there are
other helpers that rely on it, e.g. io_alloc_async_data().
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/9dc62be9e88dd0ed63c48365340e8922d2498293.1661342812.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently, there is no ordering between notification CQEs and
completions of the send flushing it, this quite complicates the
userspace, especially since we don't flush notification when the
send(+flush) request fails, i.e. there will be only one CQE. What we
can do is to make sure that notification completions come only after
sends.
The easiest way to achieve this is to not try to complete a notification
inline from io_sendzc() but defer it to task_work, considering that
io-wq sendzc is disallowed CQEs will be naturally ordered because
task_works will only be executed after we're done with submission and so
inline completion.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/cddfd1c2bf91f22b9fe08e13b7dffdd8f858a151.1661342812.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Failed requests should be marked with req_set_fail(), so links and cqe
skipping work correctly, which is missing in io_sendzc(). Note,
io_sendzc() return IOU_OK on failure, so the core code won't do the
cleanup for us.
Fixes: 06a5464be8 ("io_uring: wire send zc request type")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/e47d46fda9db30154ce66a549bb0d3380b780520.1661342812.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Return the value from rtrs_clt_rdma_cq_direct() directly instead of
storing it in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Link: https://lore.kernel.org/r/20220824075213.221397-1-ye.xingchen@zte.com.cn
Signed-off-by: Jens Axboe <axboe@kernel.dk>
To unify kmalloc functions in later patch, introduce common alloc/free
functions that does not have tracepoint.
Signed-off-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
There is not much benefit for serving large objects in kmalloc().
Let's pass large requests to page allocator like SLUB for better
maintenance of common code.
Signed-off-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Now that kmalloc_large() and kmalloc_large_node() do mostly same job,
make kmalloc_large() wrapper of kmalloc_large_node_notrace().
In the meantime, add missing flag fix code in
kmalloc_large_node_notrace().
Signed-off-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Now that kmalloc_large_node() is in common code, pass large requests
to page allocator in kmalloc_node() using kmalloc_large_node().
One problem is that currently there is no tracepoint in
kmalloc_large_node(). Instead of simply putting tracepoint in it,
use kmalloc_large_node{,_notrace} depending on its caller to show
useful address for both inlined kmalloc_node() and
__kmalloc_node_track_caller() when large objects are allocated.
Signed-off-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
In later patch SLAB will also pass requests larger than order-1 page
to page allocator. Move kmalloc_large_node() to slab_common.c.
Fold kmalloc_large_node_hook() into kmalloc_large_node() as there is
no other caller.
Signed-off-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
There is no caller of kmalloc_order_trace() except kmalloc_large().
Fold it into kmalloc_large() and remove kmalloc_order{,_trace}().
Also add tracepoint in kmalloc_large() that was previously
in kmalloc_order_trace().
Signed-off-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
__kmalloc(), __kmalloc_node(), __kmalloc_node_track_caller()
mostly do same job. Factor out common code into __do_kmalloc_node().
Note that this patch also fixes missing kasan_kmalloc() in SLUB's
__kmalloc_node_track_caller().
Signed-off-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Now that slab_alloc_node() is available for SLAB when CONFIG_NUMA=n,
remove CONFIG_NUMA ifdefs for common kmalloc functions.
Signed-off-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Make slab_alloc_node() available even when CONFIG_NUMA=n and
make slab_alloc() wrapper of slab_alloc_node().
This is necessary for further cleanup.
Signed-off-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
To implement slab_alloc_node() independent of NUMA configuration,
move NUMA fallback/alternate allocation code into __do_cache_alloc().
One functional change here is not to check availability of node
when allocating from local node.
Signed-off-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Host Turbo operates at efficient frequency when GT is not idle unless
the user or workload has forced it to a higher level. Replicate the same
behavior in SLPC by allowing the algorithm to use efficient frequency.
We had disabled it during boot due to concerns that it might break
kernel ABI for min frequency. However, this is not the case since
SLPC will still abide by the (min,max) range limits.
With this change, min freq will be at efficient frequency level at init
instead of fused min (RPn). If user chooses to reduce min freq below the
efficient freq, we will turn off usage of efficient frequency and honor
the user request. When a higher value is written, it will get toggled
back again.
The patch also corrects the register which needs to be read for obtaining
the correct efficient frequency for Gen9+.
We see much better perf numbers with benchmarks like glmark2 with
efficient frequency usage enabled as expected.
v2: Address review comments (Rodrigo)
v3: with efficient frequency being dynamic, it is possible that the req
frequency may go beyond max freq. This will cause SLPC selftests to fail.
Add a FIXME there to start the test with [RPn, RP0] instead and restore
it afterwards.
BugLink: https://gitlab.freedesktop.org/drm/intel/-/issues/5468
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220820010832.15350-1-vinay.belgaumkar@intel.com
container_of is never null, so this null check is
unnecessary.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220824080350.221614-1-chi.minghao@zte.com.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adhere to Linux kernel coding style.
Reported by checkpatch:
CHECK: multiple assignments should be avoided
Signed-off-by: Christopher Carbone <chris.m.carbone@gmail.com>
Link: https://lore.kernel.org/r/YwVBHM3z0QExtuXr@valhalla
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SOF related field.
1. Add a property "mediatek,adsp", Only when adsp phandle could be
retrieved, from DTS, the SOF related part of machine driver is executed.
2. Add a property "mediatek,dai-link" to support dai-links could be
specified from DTS
Signed-off-by: chunxu.li <chunxu.li@mediatek.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220824122319.23918-3-chunxu.li@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add SOF related field.
1. Add a property "mediatek,adsp", Only when adsp phandle could be
retrieved, from DTS, the SOF related part of machine driver is executed.
2. Add a property "mediatek,dai-link" to support dai-links could be
specified from DTS
Signed-off-by: chunxu.li <chunxu.li@mediatek.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220824122319.23918-2-chunxu.li@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The userspace can configure a loop using an ioctl call, wherein
a configuration of type loop_config is passed (see lo_ioctl()'s
case on line 1550 of drivers/block/loop.c). This proceeds to call
loop_configure() which in turn calls loop_set_status_from_info()
(see line 1050 of loop.c), passing &config->info which is of type
loop_info64*. This function then sets the appropriate values, like
the offset.
loop_device has lo_offset of type loff_t (see line 52 of loop.c),
which is typdef-chained to long long, whereas loop_info64 has
lo_offset of type __u64 (see line 56 of include/uapi/linux/loop.h).
The function directly copies offset from info to the device as
follows (See line 980 of loop.c):
lo->lo_offset = info->lo_offset;
This results in an overflow, which triggers a warning in iomap_iter()
due to a call to iomap_iter_done() which has:
WARN_ON_ONCE(iter->iomap.offset > iter->pos);
Thus, check for negative value during loop_set_status_from_info().
Bug report: https://syzkaller.appspot.com/bug?id=c620fe14aac810396d3c3edc9ad73848bf69a29e
Reported-and-tested-by: syzbot+a8e049cd3abd342936b6@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Siddh Raman Pant <code@siddh.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220823160810.181275-1-code@siddh.me
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Kuniyuki Iwashima says:
====================
net: sysctl: Fix data-races around net.core.XXX
This series fixes data-races around all knobs in net_core_table and
netns_core_table except for bpf stuff.
These knobs are skipped:
- 4 bpf knobs
- netdev_rss_key: Written only once by net_get_random_once() and
read-only knob
- rps_sock_flow_entries: Protected with sock_flow_mutex
- flow_limit_cpu_bitmap: Protected with flow_limit_update_mutex
- flow_limit_table_len: Protected with flow_limit_update_mutex
- default_qdisc: Protected with qdisc_mod_lock
- warnings: Unused
- high_order_alloc_disable: Protected with static_key_mutex
- skb_defer_max: Already using READ_ONCE()
- sysctl_txrehash: Already using READ_ONCE()
Note 5th patch fixes net.core.message_cost and net.core.message_burst,
and lib/ratelimit.c does not have an explicit maintainer.
Changes:
v3:
* Fix build failures of CONFIG_SYSCTL=n case in 13th & 14th patches
v2: https://lore.kernel.org/netdev/20220818035227.81567-1-kuniyu@amazon.com/
* Remove 4 bpf knobs and added 6 knobs
v1: https://lore.kernel.org/netdev/20220816052347.70042-1-kuniyu@amazon.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_somaxconn, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading netdev_unregister_timeout_secs, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes: 5aa3afe107 ("net: make unregister netdev warning timeout configurable")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading gro_normal_batch, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 323ebb61e3 ("net: use listified RX for handling GRO_NORMAL skbs")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_devconf_inherit_init_net, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: 856c395cfa ("net: introduce a knob to control whether to inherit devconf config")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_fb_tunnels_only_for_init_net, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: 79134e6ce2 ("net: do not create fallback tunnels for non-default namespaces")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading netdev_budget_usecs, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 7acf8a1e8a ("Replace 2 jiffies with sysctl netdev_budget_usecs to enable softirq tuning")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_max_skb_frags, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 5f74f82ea3 ("net:Add sysctl_max_skb_frags")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading netdev_budget, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 51b0bdedb8 ("[NET]: Separate two usages of netdev_max_backlog.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_net_busy_read, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 2d48d67fa8 ("net: poll/select low latency socket support")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_net_busy_poll, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 0602129286 ("net: add low latency socket poll")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tstamp_allow_data, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes: b245be1f4d ("net-timestamp: no-payload only sysctl")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_optmem_max, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading rs->interval and rs->burst, they can be changed
concurrently via sysctl (e.g. net_ratelimit_state). Thus, we
need to add READ_ONCE() to their readers.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading netdev_tstamp_prequeue, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 3b098e2d7c ("net: Consistent skb timestamping")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading netdev_max_backlog, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
While at it, we remove the unnecessary spaces in the doc.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading weight_p, it can be changed concurrently. Thus, we need
to add READ_ONCE() to its reader.
Also, dev_[rt]x_weight can be read/written at the same time. So, we
need to use READ_ONCE() and WRITE_ONCE() for its access. Moreover, to
use the same weight_p while changing dev_[rt]x_weight, we add a mutex
in proc_do_dev_weight().
Fixes: 3d48b53fb2 ("net: dev_weight: TX/RX orthogonality")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>