Use link->exit() rather than pdev->remove() to unassign jack during card
unbind procedure so codec link initialization and exit procedures are
symmetrical.
Also, there is no need to perform search for codec dai in suspend_pre()
and resume_post() ourselves. Use snd_soc_card_get_codec_dai() instead.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221125184032.2565979-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Horatiu Vultur says:
====================
Add support for lan966x IS2 VCAP
This provides initial support for lan966x for 'tc' traffic control
userspace tool and its flower filter. For this is required to use
the VCAP library.
Currently supported flower filter keys and actions are:
- source and destination MAC address keys
- trap action
====================
Link: https://lore.kernel.org/r/20221125095010.124458-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
On lan966x the layout of the vcap memory is different than on sparx5.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Implement vcap_operations and enable default port keyset configuration
for each port. Now it is possible actually write/read/move entries in
the VCAP.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Extend matchall with action goto. This is needed to enable the lookup in
the VCAP. It is needed to connect chain 0 to a chain that is recognized
by the HW.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently the only supported action is ACTION_TRAP and the only
dissector is ETH_ADDRS. Others will be added in future patches.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add registers used to access vcap controller.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This provides the lan966x is2 model and adds it to the vcap control
instance that will be provided to the vcap API.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When lan966x driver is initialized, initialize also the VCAP module for
lan966x.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add the keysets, keys, actionsets and actions used by lan966x in IS2.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently there are 2 files that contain the keyfields, keys,
actionfields and actions. First file is used by the kunit while the
second one is used by VCAP api.
The header file that is used by kunit is just a super set of the of the
header file used by VCAP api.
Therefore not to have duplicate information in different files which is
also harder to maintain, create a single file that is used both by API
and by kunit.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Simplify a bit the code by using regmap_set_bits() and
regmap_clear_bits() instead of regmap_update_bits() when possible.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The MACH_INGENIC Kconfig option will be selected when building a kernel
targeting Ingenic SoCs, but also when compiling a generic MIPS kernel
that happens to support Ingenic SoCs.
Therefore, if MACH_INGENIC is not set, we know that we're not even
trying to build a generic kernel that supports these SoCs, and we can
hide the options to compile the SoC-specific drivers.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Ingenic SoCs all require CONFIG_OF, so there is no case where we want to
use this driver without CONFIG_OF.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add missing "reg = <0>;" property to the flash@0 node in the example.
Fixes: dd71cd4dd6 ("spi: Add Nuvoton WPCM450 Flash Interface Unit (FIU) bindings")
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221129102225.3598044-3-j.neuschaefer@gmx.net
Signed-off-by: Mark Brown <broonie@kernel.org>
The nuvoton,wpcm450-fiu binding's example includes
nuvoton,wpcm450-clk.h, which has not been merged yet,
thus causing a dt_binding_check error on -next.
Fix this error by simply hardcoding the clock index in the example,
before the breakage spreads any further.
Fixes: dd71cd4dd6 ("spi: Add Nuvoton WPCM450 Flash Interface Unit (FIU) bindings")
Reported-by: Rob Herring <robh@kernel.org>
Reported-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221129102225.3598044-2-j.neuschaefer@gmx.net
Signed-off-by: Mark Brown <broonie@kernel.org>
sc7180_lpass_dev_resume() logs an error if clk_bulk_prepare_enable()
fails. The clock framework already generates error logs if anything
goes wrong, so the logging in _resume() is redundant, drop it.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20221129001633.v2.1.I8d1993f41f0da1eac0ecba321678ac489f9c0b9b@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Update lpass sc7280 platform driver with PM ops, such as
system supend and resume callbacks.
This update is required to disable clocks during supend and
avoid XO shutdown issue.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Tested-by: Rahul Ajmeriya <quic_rajmeriy@quicinc.com>
Link: https://lore.kernel.org/r/1669703784-27589-1-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
syzbot reported use-after-free in tun_detach() [1]. This causes call
trace like below:
==================================================================
BUG: KASAN: use-after-free in notifier_call_chain+0x1ee/0x200 kernel/notifier.c:75
Read of size 8 at addr ffff88807324e2a8 by task syz-executor.0/3673
CPU: 0 PID: 3673 Comm: syz-executor.0 Not tainted 6.1.0-rc5-syzkaller-00044-gcc675d22e422 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xd1/0x138 lib/dump_stack.c:106
print_address_description mm/kasan/report.c:284 [inline]
print_report+0x15e/0x461 mm/kasan/report.c:395
kasan_report+0xbf/0x1f0 mm/kasan/report.c:495
notifier_call_chain+0x1ee/0x200 kernel/notifier.c:75
call_netdevice_notifiers_info+0x86/0x130 net/core/dev.c:1942
call_netdevice_notifiers_extack net/core/dev.c:1983 [inline]
call_netdevice_notifiers net/core/dev.c:1997 [inline]
netdev_wait_allrefs_any net/core/dev.c:10237 [inline]
netdev_run_todo+0xbc6/0x1100 net/core/dev.c:10351
tun_detach drivers/net/tun.c:704 [inline]
tun_chr_close+0xe4/0x190 drivers/net/tun.c:3467
__fput+0x27c/0xa90 fs/file_table.c:320
task_work_run+0x16f/0x270 kernel/task_work.c:179
exit_task_work include/linux/task_work.h:38 [inline]
do_exit+0xb3d/0x2a30 kernel/exit.c:820
do_group_exit+0xd4/0x2a0 kernel/exit.c:950
get_signal+0x21b1/0x2440 kernel/signal.c:2858
arch_do_signal_or_restart+0x86/0x2300 arch/x86/kernel/signal.c:869
exit_to_user_mode_loop kernel/entry/common.c:168 [inline]
exit_to_user_mode_prepare+0x15f/0x250 kernel/entry/common.c:203
__syscall_exit_to_user_mode_work kernel/entry/common.c:285 [inline]
syscall_exit_to_user_mode+0x1d/0x50 kernel/entry/common.c:296
do_syscall_64+0x46/0xb0 arch/x86/entry/common.c:86
entry_SYSCALL_64_after_hwframe+0x63/0xcd
The cause of the issue is that sock_put() from __tun_detach() drops
last reference count for struct net, and then notifier_call_chain()
from netdev_state_change() accesses that struct net.
This patch fixes the issue by calling sock_put() from tun_detach()
after all necessary accesses for the struct net has done.
Fixes: 83c1f36f98 ("tun: send netlink notification when the device is modified")
Reported-by: syzbot+106f9b687cd64ee70cd1@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=96eb7f1ce75ef933697f24eeab928c4a716edefe [1]
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Link: https://lore.kernel.org/r/20221124175134.1589053-1-syoshida@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ath12k is a new mac80211 driver for Qualcomm Wi-Fi 7 devices, first
supporting QCN9274 and WCN7850 PCI devices. QCN9274 supports both AP
and station; WCN7850 supports only station mode. Monitor mode is not
(yet) supported. Only PCI bus devices are supported.
ath12k is forked from an earlier version of ath11k. It was simpler to
have a "clean start" for the new generation and not try to share the
code with ath11k. This makes maintenance easier and avoids major
changes in ath11k, which would have significantly increased the risk
of regressions in existing setups.
ath12k uses le32 and cpu_to_le32() macros to handle endian
conversions, instead of using the firmware byte swap feature utilized
by ath11k. There is only one kernel module, named ath12k.ko.
Currently ath12k only supports HE mode (IEEE 802.11ax) or older, but
work is ongoing to add EHT mode (IEEE 802.11be) support.
The size of the driver is ~41 kLOC and 45 files. To make the review
easier, this initial version of ath12k does not support Device Tree,
debugfs or any other extra features. Those will be added later, after
ath12k is accepted to upstream.
The driver is build tested by Intel's kernel test robot with both GCC
and Clang. Sparse reports no warnings. The driver is mostly free of
checkpatch warnings, albeit few of the warnings are omitted on
purpose, list of them here:
https://github.com/qca/qca-swiss-army-knife/blob/master/tools/scripts/ath12k/ath12k-check#L52
The driver has had multiple authors who are listed in alphabetical
order below.
Co-developed-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Signed-off-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Co-developed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Co-developed-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Signed-off-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Co-developed-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Co-developed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Co-developed-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Co-developed-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Co-developed-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Co-developed-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Signed-off-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Co-developed-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Lorenzo Bianconi says:
====================
refactor mtk_wed code to introduce SER support
Refactor mtk_wed support in order to introduce proper integration for hw reset
between mtk_eth_soc/mtk_wed and mt76 drivers.
====================
Link: https://lore.kernel.org/r/cover.1669303154.git.lorenzo@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Introduce reset parameter to mtk_wed_tx_ring_setup signature.
This is a preliminary patch to add Wireless Ethernet Dispatcher reset
support.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Introduce mtk_wed_rx_reset routine in order to reset rx DMA for Wireless
Ethernet Dispatcher available on MT7986 SoC.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Update mtk_wed_stop routine and rename old mtk_wed_stop() to
mtk_wed_deinit(). This is a preliminary patch to add Wireless Ethernet
Dispatcher reset support.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Remove duplicated code. Increase poll timeout to 10ms in order to be
aligned with vendor sdk.
This is a preliminary patch to add Wireless Ethernet Dispatcher reset
support.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Move MTK_WDMA_RESET_IDX configuration in mtk_wdma_rx_reset routine.
Increase poll timeout to 10ms in order to be aligned with vendor sdk.
This is a preliminary patch to add Wireless Ethernet Dispatcher reset
support.
Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In ARM, the mapping of instruction memory is always little-endian, except
some BE-32 supported ARM architectures. Such as ARMv7-R, its instruction
endianness may be BE-32. Of course, its data endianness will also be BE-32
mode. Due to two negatives make a positive, the instruction stored in the
register after reading is in little-endian format. But for the case of
BE-8, the instruction endianness is LE, the instruction stored in the
register after reading is in big-endian format, which is inconsistent
with the disassembled one.
For example:
The content of disassembly:
c0429ee8: e3500000 cmp r0, #0
c0429eec: 159f2044 ldrne r2, [pc, #68]
c0429ef0: 108f2002 addne r2, pc, r2
c0429ef4: 1882000a stmne r2, {r1, r3}
c0429ef8: e7f000f0 udf #0
The output of undefined instruction exception:
Internal error: Oops - undefined instruction: 0 [#1] SMP ARM
... ...
Code: 000050e3 44209f15 02208f10 0a008218 (f000f0e7)
This inconveniences the checking of instructions. What's worse is that,
for somebody who don't know about this, might think the instructions are
all broken.
So, when CONFIG_CPU_ENDIAN_BE8=y, let's convert the instructions to
little-endian format before they are printed. The conversion result is
as follows:
Code: e3500000 159f2044 108f2002 1882000a (e7f000f0)
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Miquel Raynal says:
====================
Marvell nvmem mac addresses support
Now that we are aligned on how to make information available from static
storage media to drivers like Ethernet controller drivers or switch
drivers by using nvmem cells and going through the whole nvmem
infrastructure, here are two driver updates to reflect these changes.
Prior to the driver updates, I propose:
* Reverting binding changes which should have never been accepted like
that.
* A conversion of the (old) Prestera and DFX server bindings (optional,
can be dropped if not considered necessary).
* A better description of the more recent Prestera PCI switch.
Please mind that this series cannot break anything since retrieving the
MAC address Prestera driver has never worked upstream, because the (ONIE
tlv) driver supposed to export the MAC address has not been accepted in
its original form and has been updated to the nvmem-layout
infrastructure (bindings have been merged, the code remains to be
applied).
====================
Link: https://lore.kernel.org/r/20221124111556.264647-1-miquel.raynal@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ONIE standard describes the organization of tlv (type-length-value)
arrays commonly stored within NVMEM devices on common networking
hardware.
Several drivers already make use of NVMEM cells for purposes like
retrieving a default MAC address provided by the manufacturer.
What made ONIE tables unusable so far was the fact that the information
where "dynamically" located within the table depending on the
manufacturer wishes, while Linux NVMEM support only allowed statically
defined NVMEM cells. Fortunately, this limitation was eventually tackled
with the introduction of discoverable cells through the use of NVMEM
layouts, making it possible to extract and consistently use the content
of tables like ONIE's tlv arrays.
Parsing this table at runtime in order to get various information is now
possible. So, because many Marvell networking switches already follow
this standard, let's consider using NVMEM cells as a new valid source of
information when looking for a base MAC address, which is one of the
primary uses of these new fields. Indeed, manufacturers following the
ONIE standard are encouraged to provide a default MAC address there, so
let's eventually use it if no other MAC address has been found using the
existing methods.
Link: https://opencomputeproject.github.io/onie/design-spec/hw_requirements.html
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This driver fist makes an expensive DT lookup to retrieve its DT node
(this is a PCI driver) in order to later search for the
base-mac-provider property. This property has no reality upstream and
this code should not have been accepted like this in the first
place. Instead, there is a proper nvmem interface that should be
used. Let's avoid these extra lookups and rely on the nvmem internal
logic.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Export
of_get_mac_addr_nvmem()
and rename it to
of_get_mac_address_nvmem()
in order to fit the convention followed by the existing exported helpers
of the same kind.
This way, OF compatible drivers using eg. fwnode_get_mac_address() can
do a direct call to it instead of calling of_get_mac_address() just for
the nvmem step, avoiding to repeat an expensive DT lookup which has
already been done once.
Eventually, fwnode_get_mac_address() should probably be updated to
perform the nvmem lookup directly, but as of today, nvmem cells seem not
to be supported by ACPI yet which would defeat this kind of extension.
Suggested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Even though the devices have very little in common beside the name and
the main "switch" feature, Marvell Prestera switch family is also
composed of PCI-only devices which can receive additional static
properties, like nvmem cells to point at MAC addresses, for
instance. Let's describe them.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The currently described switch family is named AlleyCat3, it is a memory
mapped switch found on Armada XP boards.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Even though this description is not used anywhere upstream (no matching
driver), while on this file I decided I would try a conversion to yaml
in order to clarify the prestera family description.
I cannot keep the nodename dfx-server@xxxx so I switched to dfx-bus@xxxx
which matches simple-bus.yaml. Otherwise I took the example context from
the only user of this compatible: armada-xp-98dx3236.dtsi, which is a
rather old and not perfect DT.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This reverts commit 40acc05271.
marvell,prestera.txt is an old file describing the old Alleycat3
standalone switches. The commit mentioned above actually hacked these
bindings to add support for a device tree property for a more modern
version of the IP connected over PCI, using only the generic compatible
in order to retrieve the device node from the prestera driver to read
one static property.
The problematic property discussed here is "base-mac-provider". The
original intent was to point to a nvmem device which could produce the
relevant nvmem-cell. This property has never been acked by DT
maintainers and fails all the layering that has been brought with the nvmem
bindings by pointing at a nvmem producer, bypassing the existing nvmem
bindings, rather than a nvmem cell directly. Furthermore, the property
cannot even be used upstream because it expected the ONIE tlv driver to
produce a specific cell, driver which used nacked bindings and thus was
never merged, replaced by a more integrated concept: the nvmem-layout.
So let's forget about this temporary addition, safely avoiding the need
for any backward compatibility handling. A new (yaml) binding file will
be brought with the prestera bindings, and there we will actually
include a description of the modern IP over PCI, including the right way
to point to a nvmem cell.
Cc: Vadym Kochan <vadym.kochan@plvision.eu>
Cc: Taras Chornyi <tchornyi@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When (size != 0 || ptrs->lvds_ entries != 3), the program tries to
free() the ptrs. However, the ptrs is not created by calling kzmalloc(),
but is obtained by pointer offset operation.
This may lead to memory leaks or undefined behavior.
Fix this by replacing the arguments of kfree() with ptrs_block.
Fixes: a87d0a8476 ("drm/i915/bios: Generate LFP data table pointers if the VBT lacks them")
Signed-off-by: Xia Fukun <xiafukun@huawei.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221125063428.69486-1-xiafukun@huawei.com
Document both the restriction on VM_MTE_ALLOWED mappings and
the relaxation for shared mappings.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221104011041.290951-9-pcc@google.com
Certain VMMs such as crosvm have features (e.g. sandboxing) that depend
on being able to map guest memory as MAP_SHARED. The current restriction
on sharing MAP_SHARED pages with the guest is preventing the use of
those features with MTE. Now that the races between tasks concurrently
clearing tags on the same page have been fixed, remove this restriction.
Note that this is a relaxation of the ABI.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221104011041.290951-8-pcc@google.com
Previously we allowed creating a memslot containing a private mapping that
was not VM_MTE_ALLOWED, but would later reject KVM_RUN with -EFAULT. Now
we reject the memory region at memslot creation time.
Since this is a minor tweak to the ABI (a VMM that created one of
these memslots would fail later anyway), no VMM to my knowledge has
MTE support yet, and the hardware with the necessary features is not
generally available, we can probably make this ABI change at this point.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221104011041.290951-7-pcc@google.com
Initialising the tags and setting PG_mte_tagged flag for a page can race
between multiple set_pte_at() on shared pages or setting the stage 2 pte
via user_mem_abort(). Introduce a new PG_mte_lock flag as PG_arch_3 and
set it before attempting page initialisation. Given that PG_mte_tagged
is never cleared for a page, consider setting this flag to mean page
unlocked and wait on this bit with acquire semantics if the page is
locked:
- try_page_mte_tagging() - lock the page for tagging, return true if it
can be tagged, false if already tagged. No acquire semantics if it
returns true (PG_mte_tagged not set) as there is no serialisation with
a previous set_page_mte_tagged().
- set_page_mte_tagged() - set PG_mte_tagged with release semantics.
The two-bit locking is based on Peter Collingbourne's idea.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Peter Collingbourne <pcc@google.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221104011041.290951-6-pcc@google.com
As with PG_arch_2, this flag is only allowed on 64-bit architectures due
to the shortage of bits available. It will be used by the arm64 MTE code
in subsequent patches.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Cc: Will Deacon <will@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Steven Price <steven.price@arm.com>
[catalin.marinas@arm.com: added flag preserving in __split_huge_page_tail()]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221104011041.290951-5-pcc@google.com
Currently sanitise_mte_tags() checks if it's an online page before
attempting to sanitise the tags. Such detection should be done in the
caller via the VM_MTE_ALLOWED vma flag. Since kvm_set_spte_gfn() does
not have the vma, leave the page unmapped if not already tagged. Tag
initialisation will be done on a subsequent access fault in
user_mem_abort().
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
[pcc@google.com: fix the page initializer]
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Peter Collingbourne <pcc@google.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221104011041.290951-4-pcc@google.com
Currently the PG_mte_tagged page flag mostly means the page contains
valid tags and it should be set after the tags have been cleared or
restored. However, in mte_sync_tags() it is set before setting the tags
to avoid, in theory, a race with concurrent mprotect(PROT_MTE) for
shared pages. However, a concurrent mprotect(PROT_MTE) with a copy on
write in another thread can cause the new page to have stale tags.
Similarly, tag reading via ptrace() can read stale tags if the
PG_mte_tagged flag is set before actually clearing/restoring the tags.
Fix the PG_mte_tagged semantics so that it is only set after the tags
have been cleared or restored. This is safe for swap restoring into a
MAP_SHARED or CoW page since the core code takes the page lock. Add two
functions to test and set the PG_mte_tagged flag with acquire and
release semantics. The downside is that concurrent mprotect(PROT_MTE) on
a MAP_SHARED page may cause tag loss. This is already the case for KVM
guests if a VMM changes the page protection while the guest triggers a
user_mem_abort().
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
[pcc@google.com: fix build with CONFIG_ARM64_MTE disabled]
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Peter Collingbourne <pcc@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221104011041.290951-3-pcc@google.com
Commit 4beba9486a ("mm: Add PG_arch_2 page flag") introduced a new
page flag for all 64-bit architectures. However, even if an architecture
is 64-bit, it may still have limited spare bits in the 'flags' member of
'struct page'. This may happen if an architecture enables SPARSEMEM
without SPARSEMEM_VMEMMAP as is the case with the newly added loongarch.
This architecture port needs 19 more bits for the sparsemem section
information and, while it is currently fine with PG_arch_2, adding any
more PG_arch_* flags will trigger build-time warnings.
Add a new CONFIG_ARCH_USES_PG_ARCH_X option which can be selected by
architectures that need more PG_arch_* flags beyond PG_arch_1. Select it
on arm64.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
[pcc@google.com: fix build with CONFIG_ARM64_MTE disabled]
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Steven Price <steven.price@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221104011041.290951-2-pcc@google.com
The call netdev_{put, hold} of dev_{put, hold} will check NULL,
so there is no need to check before using dev_{put, hold}.
Fix the following coccicheck warnings:
/drivers/infiniband/hw/mlx4/main.c:1311:2-10: WARNING:
WARNING NULL check before dev_{put, hold} functions is not needed.
/drivers/infiniband/hw/mlx4/main.c:148:2-10: WARNING:
WARNING NULL check before dev_{put, hold} functions is not needed.
/drivers/infiniband/hw/mlx4/main.c:1959:3-11: WARNING:
WARNING NULL check before dev_{put, hold} functions is not needed.
/drivers/infiniband/hw/mlx4/main.c:1962:3-10: WARNING:
WARNING NULL check before dev_{put, hold} functions is not needed.
Signed-off-by: zhang songyi <zhang.songyi@zte.com.cn>
Link: https://lore.kernel.org/r/202211291554079687539@zte.com.cn
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Users of intel_gt_retire_requests_timeout() expect 0 return value on
success. However, we have no protection from passing back 0 potentially
returned by a call to dma_fence_wait_timeout() when it succedes right
after its timeout has expired.
Replace 0 with -ETIME before potentially using the timeout value as return
code, so -ETIME is returned if there are still some requests not retired
after timeout, 0 otherwise.
v3: Use conditional expression, more compact but also better reflecting
intention standing behind the change.
v2: Move the added lines down so flush_submission() is not affected.
Fixes: f33a8a5160 ("drm/i915: Merge wait_for_timelines with retire_request")
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: stable@vger.kernel.org # v5.5+
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221121145655.75141-3-janusz.krzysztofik@linux.intel.com
(cherry picked from commit f301a29f14)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Commit b97060a99b ("drm/i915/guc: Update intel_gt_wait_for_idle to work
with GuC") extended the API of intel_gt_retire_requests_timeout() with an
extra argument 'remaining_timeout', intended for passing back unconsumed
portion of requested timeout when 0 (success) is returned. However, when
request retirement happens to succeed despite an error returned by a call
to dma_fence_wait_timeout(), that error code (a negative value) is passed
back instead of remaining time. If we then pass that negative value
forward as requested timeout to intel_uc_wait_for_idle(), an explicit BUG
will be triggered.
If request retirement succeeds but an error code is passed back via
remaininig_timeout, we may have no clue on how much of the initial timeout
might have been left for spending it on waiting for GuC to become idle.
OTOH, since all pending requests have been successfully retired, that
error code has been already ignored by intel_gt_retire_requests_timeout(),
then we shouldn't fail.
Assume no more time has been left on error and pass 0 timeout value to
intel_uc_wait_for_idle() to give it a chance to return success if GuC is
already idle.
v3: Don't fail on any error passed back via remaining_timeout.
v2: Fix the issue on the caller side, not the provider.
Fixes: b97060a99b ("drm/i915/guc: Update intel_gt_wait_for_idle to work with GuC")
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Cc: stable@vger.kernel.org # v5.15+
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221121145655.75141-2-janusz.krzysztofik@linux.intel.com
(cherry picked from commit f235dbd5b7)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
