Change the inode hash/lookup VFS API functions to accept u64 parameters
instead of unsigned long for inode numbers and hash values. This is
preparation for widening i_ino itself to u64, which will allow
filesystems to store full 64-bit inode numbers on 32-bit architectures.
Since unsigned long implicitly widens to u64 on all architectures, this
change is backward-compatible with all existing callers.
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Link: https://patch.msgid.link/20260304-iino-u64-v3-1-2257ad83d372@kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christian Brauner <brauner@kernel.org>
This improves log accuracy for NTFS debugging and removes unnecessary
reliance on the VFS i_ino field ahead of the core VFS type change.
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Changes the type of ntfs_inode::mft_no from unsigned long to u64
to safely handle the full 48-bit range without truncation risk, especially
in preparation for broader VFS inode number type (i_ino:u64) and to
improve consistency with ntfs driver practices.
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Add SoC identification for the RZ/G3L SoC using the System Controller
(SYSC) block.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260203103031.247435-5-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This series enables QoS configuration for QNOC type device which
can be found on QCS8300 platform. It enables QoS configuration
for master ports with predefined priority and urgency forwarding.
This helps in prioritizing the traffic originating from different
interconnect masters at NOC (Network On Chip).
The system may function normally without this feature. However,
enabling QoS helps optimize latency and bandwidth across subsystems
like CPU, GPU, and multimedia engines, which becomes important in
high-throughput scenarios. This is a feature aimed at performance
enhancement to improve system performance under concurrent workloads.
* icc-qcs8300
dt-bindings: interconnect: qcom,qcs8300-rpmh: add clocks property to enable QoS
interconnect: qcom: qcs8300: enable QoS configuration
Link: https://msgid.link/20260127090116.1438780-1-odelu.kukatla@oss.qualcomm.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Document RZ/G3L (R9A08G046) SYSC bindings. The SYSC block found on the
RZ/G3L SoC is similar to the one found on RZ/G3S.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260203103031.247435-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Document Renesas RZ/G3L (R9A08G046) SoC variants and the Renesas RZ/G3L
SMARC Carrier-II EVK board which is based on the Renesas RZ/G3L SMARC SoM.
The RZ/G3L SMARC Carrier-II EVK consists of an RZ/G3L SoM module and a
SMARC Carrier-II carrier board. The SoM module sits on top of the carrier
board.
Reviewed-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260203103031.247435-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Mahua is a derivative of the Glymur SoC and shares a significant
portion of its interconnect topology with Glymur. As such, this
series extends the existing Glymur interconnect driver to support
Mahua, reusing common definitions where possible and adding
SoC-specific configurations where necessary.
* icc-mahua
dt-bindings: interconnect: document the RPMh Network-On-Chip interconnect in Mahua SoC
interconnect: qcom: glymur: Add Mahua SoC support
Link: https://msgid.link/20260209-mahua_icc-v3-0-c65f3dfd72c8@oss.qualcomm.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Add interconnect support for the Qualcomm Eliza SoC.
* icc-eliza
dt-bindings: interconnect: document the RPMh Network-On-Chip interconnect in Eliza SoC
interconnect: qcom: Add Eliza interconnect provider driver
dt-bindings: interconnect: OSM L3: Add Eliza EPSS L3 compatible
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The HW user manual for the Renesas RZ/V2H(P) SoC specifies
that only the WDT1 IP is supposed to be used by Linux,
while the WDT{0,2,3} IPs are supposed to be used by the CM33
and CR8 cores.
Remove the clock and reset entries for WDT{0,2,3} to prevent
interfering with the CM33 and CR8 cores.
This change is harmless as only WDT1 is used by Linux, there
are no users for the WDT{0,2,3} cores.
Fixes: 3aeccbe081 ("clk: renesas: r9a09g057: Add clock and reset entries for GTM/RIIC/SDHI/WDT")
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260203124247.7320-4-fabrizio.castro.jz@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Document the RPMh Network-On-Chip Interconnect of the Eliza platform.
Signed-off-by: Odelu Kukatla <odelu.kukatla@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://msgid.link/20260224-eliza-interconnect-v4-1-ad75855d5018@oss.qualcomm.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Add driver for the Qualcomm interconnect buses found in Eliza
based platforms. The topology consists of several NoCs that are
controlled by a remote processor that collects the aggregated
bandwidth for each master-slave pairs.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Odelu Kukatla <odelu.kukatla@oss.qualcomm.com>
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://msgid.link/20260224-eliza-interconnect-v4-2-ad75855d5018@oss.qualcomm.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The rzt2h_gpio_get_direction() function is called from
gpiod_get_direction(), which ends up being used within the __setup_irq()
call stack when requesting an interrupt.
__setup_irq() holds a raw_spinlock_t with IRQs disabled, which creates
an atomic context. spinlock_t cannot be used within atomic context
when PREEMPT_RT is enabled, since it may become a sleeping lock.
An "[ BUG: Invalid wait context ]" splat is observed when running with
CONFIG_PROVE_LOCKING enabled, describing exactly the aforementioned call
stack.
__setup_irq() needs to hold a raw_spinlock_t with IRQs disabled to
serialize access against a concurrent hard interrupt.
Switch to raw_spinlock_t to fix this.
Fixes: 829dde3369 ("pinctrl: renesas: rzt2h: Add GPIO IRQ chip to handle interrupts")
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260205103930.666051-1-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When calling of_parse_phandle_with_fixed_args(), the caller is
responsible for calling of_node_put() to release the device node
reference.
In rzt2h_gpio_register(), the driver fails to call of_node_put() to
release the reference in of_args.np, which causes a memory leak.
Add the missing of_node_put() call to fix the leak.
Fixes: 34d4d09307 ("pinctrl: renesas: Add support for RZ/T2H")
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260127-rzt2h-v1-1-86472e7421b8@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Glymur and Kaanapali are codenames of Qualcomm SoCs, not acronyms.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://msgid.link/20260217130035.281752-4-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Glymur is a codename of Qualcomm SoC, not an acronym.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Taniya Das <taniya.das@oss.qualcomm.com>
Link: https://msgid.link/20260217130035.281752-3-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Document the OSM L3 found in the Qualcomm SM8550 platform.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
Link: https://msgid.link/20260219-sm8550-ddr-bw-scaling-v3-1-75c19152e921@gmail.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
RZ/N2H (R9A09G087) has three DMA controllers that can be used by
peripherals like SPI to offload data transfers from the CPU.
Wire up the DMA channels for the SPI peripherals.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260128215132.1353381-4-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
RZ/T2H (R9A09G077) has three DMA controllers that can be used by
peripherals like SPI to offload data transfers from the CPU.
Wire up the DMA channels for the SPI peripherals.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260128215132.1353381-3-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Describe the 9FGV0841 PCIe and USB3.0 clock generator present on Ebisu
board. The clock generator supplies 100 MHz differential clock for both
PCIe slot and BT/WLAN expansion port, as well as for the USB 3.0 PHY.
This configuration is valid for SW49 in OFF position, which means the
PCIe signals are routed to the PCIe slot and U11 9FGV0841 PCIe clock
generator output 3 supplies clock to the PCIe slot.
In case the SW49 is set to ON position, which means the PCIe signals
are routed to the EX BT/WLAN expansion port, and U11 9FGV0841 PCIe
clock generator output 4 supplies clock to the port and &pciec0_rp
clocks should be changed to "clocks = <&pcie_usb_clk 4>;". Once the
BT/WLAN port is tested, this can be implemented using a DTO. Until
then, assume SW49 is set to OFF position.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260118135038.8033-10-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Describe the 9FGV0841 PCIe and USB3.0 clock generator present on ULCB
boards. The clock generator supplies 100 MHz differential clock for
both PCIe ports, the USB 3.0 PHY and SATA.
SATA is not yet described in the ULCB DT, therefore the connection to
this clock generator is not described here either.
The H3 ULCB schematic does describe connection from output DIF7 to
USB3S1_CLK_*, but these signals do not exist on the SoC, therefore
this connection is also not described.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260118135038.8033-9-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Describe the 9FGV0841 PCIe and USB3.0 clock generator present on both
Salvator-X and Salvator-XS boards. The clock generator supplies 100 MHz
differential clock for both PCIe ports, as well as for the USB 3.0 PHY.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260118135038.8033-8-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add USB 3.0 PHY and PHY clock node for R-Car E3. The PHY node is
different in that it does not have control registers and extal clock,
which are not routed to the SoC pads on R-Car E3, therefore describe the
PHY as usb-nop-xceiv simple PHY. Add USB3S0 clock pad fixed-clock node,
the frequency has to be overridden at board level.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260118135038.8033-7-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add node which describes the root port in the PCIe controller DT node.
This can be used together with the pwrctrl driver to control clock and
power supply to a PCIe slot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260118135038.8033-6-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add nodes which describe the root ports in the PCIe controller DT nodes.
This can be used together with the pwrctrl driver to control clock and
power supply to a PCIe slot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260118135038.8033-5-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add nodes which describe the root ports in the PCIe controller DT nodes.
This can be used together with the pwrctrl driver to control clock and
power supply to a PCIe slot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260118135038.8033-4-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add nodes which describe the root ports in the PCIe controller DT nodes.
This can be used together with the pwrctrl driver to control clock and
power supply to a PCIe slot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260118135038.8033-3-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add nodes which describe the root ports in the PCIe controller DT nodes.
This can be used together with the pwrctrl driver to control clock and
power supply to a PCIe slot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260118135038.8033-2-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
In RZ/N1 SoCs, CPUs are allowed to work at 125, 250 or 500 MHz when the
'ref' clock frequency value is set to 500 MHz which is the default 'ref'
clock frequency value.
Add support for CPU frequency scaling defining those 3 frequencies in
the opp-table with the assumption that the 'ref' clock is set to its
default value.
Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260115164905.1203453-1-herve.codina@bootlin.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The U-Boot SPL is responsible for initializing the hardware and it does
also initialize HSCIF0 and its pinmux, mark the HSCIF0 pinmux as needed
in all bootloader stages. The SPL also uses OTP to determine the exact
V4H SoC variant during DRAM initialization, to determine which is the
maximum allowed DRAM rate, mark OTP as required in all bootloader stages
as well.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260112234642.225993-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The default settings for the Versa3 device on the Renesas RZ/G3S SMARC
SoM board have PLL2 disabled. PLL2 was later enabled together with audio
support, as it is required to support both 44.1 kHz and 48 kHz audio.
With PLL2 enabled, it was observed that Linux occasionally either hangs
during boot (the last log message being related to the I2C probe) or
randomly crashes. This was mainly reproducible on cold boots. During
debugging, it was also noticed that the Unicode replacement character (�)
sometimes appears on the serial console. Further investigation traced this
to the configuration applied through the Versa3 register at offset 0x1c,
which controls PLL enablement.
The appearance of the Unicode replacement character suggested an issue
with the SoC reference clock. The RZ/G3S reference clock is provided by
the Versa3 clock generator (REF output).
After checking with the Renesas Versa3 hardware team, it was found that
this is related to the PLL2 lock bit being set through the
renesas,settings DT property.
The PLL lock bit must be set to avoid unstable clock output from the PLL.
However, due to the Versa3 hardware design, when a PLL lock bit is set,
all outputs (including the REF clock) are temporarily disabled until the
configured PLLs become stable.
As an alternative, the bypass bit can be used. This does not interrupt the
PLL2 output or any other Versa3 outputs, but it may result in temporary
instability on PLL2 output while the configuration is applied. Since PLL2
feeds only the audio path and audio is not used during early boot, this is
acceptable and does not affect system boot.
Drop the PLL2 lock bit and set the bypass bit instead.
This has been tested with more than 1000 cold boots.
Fixes: a94253232b ("arm64: dts: renesas: rzg3s-smarc-som: Add versa3 clock generator node")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260302135703.162601-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The CPG register regions were incorrectly sized. Update them to match
the actual hardware specification:
- First region (0x80280000): 0x1000 -> 0x10000 (64kiB)
- Second region (0x81280000): 0x9000 -> 0x10000 (64kiB)
Fixes: 4b3d31f0b8 ("arm64: dts: renesas: Add initial SoC DTSI for the RZ/N2H SoC")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260213131742.3606334-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The CPG register regions were incorrectly sized. Update them to match
the actual hardware specification:
- First region (0x80280000): 0x1000 -> 0x10000 (64kiB)
- Second region (0x81280000): 0x9000 -> 0x10000 (64kiB)
Fixes: d17b34744f ("arm64: dts: renesas: Add initial support for the Renesas RZ/T2H SoC")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260213131742.3606334-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The HW user manual for the Renesas RZ/V2H(P) SoC (a.k.a r9a09g057)
states that only WDT1 is supposed to be accessed by the CA55 cores.
WDT0 is supposed to be used by the CM33 core, WDT2 is supposed
to be used by the CR8 core 0, and WDT3 is supposed to be used
by the CR8 core 1.
Remove wdt{0,2,3} from the SoC specific device tree to make it
compliant with the specification from the HW manual.
This change is harmless as there are currently no users of the
wdt{0,2,3} device tree nodes, only the wdt1 node is actually used.
Fixes: 095105496e ("arm64: dts: renesas: r9a09g057: Add WDT0-WDT3 nodes")
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260203124247.7320-3-fabrizio.castro.jz@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Set an appropriate ramp delay for the SD0 I/O voltage regulator in the
CN15 SD overlay to make UHS-I voltage switching reliable during card
initialization.
This issue was observed on the RZ/V2H EVK, while the same UHS-I cards
worked on the RZ/V2N EVK without problems. Adding the ramp delay makes
the behavior consistent and avoids SD init timeouts.
Before this change SD0 could fail with:
mmc0: error -110 whilst initialising SD card
With the delay in place UHS-I cards enumerate correctly:
mmc0: new UHS-I speed SDR104 SDXC card at address aaaa
mmcblk0: mmc0:aaaa SR64G 59.5 GiB
mmcblk0: p1
Fixes: 3d6c2bc762 ("arm64: dts: renesas: Add CN15 eMMC and SD overlays for RZ/V2H and RZ/V2N EVKs")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260123225957.1007089-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a ramp delay of 60 uV/us to the vqmmc_sdhi0 voltage regulator to
fix UHS-I SD card detection failures.
Measurements on CN78 pin 4 showed the actual voltage ramp time to be
21.86ms when switching between 3.3V and 1.8V. A 25ms ramp delay has
been configured to provide adequate margin. The calculation is based
on the voltage delta of 1.5V (3.3V - 1.8V):
1500000 uV / 60 uV/us = 25000 us (25ms)
Prior to this patch, UHS-I cards failed to initialize with:
mmc0: error -110 whilst initialising SD card
After this patch, UHS-I cards are properly detected on SD0:
mmc0: new UHS-I speed SDR104 SDXC card at address aaaa
mmcblk0: mmc0:aaaa SR64G 59.5 GiB
Fixes: d065453e5e ("arm64: dts: renesas: rzt2h-rzn2h-evk: Enable SD card slot")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260123225957.1007089-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Some QCS8300 interconnect nodes have QoS registers located inside
a block whose interface is clock-gated. For those nodes, driver
must enable the corresponding clock(s) before accessing the
registers. Add the 'clocks' property so the driver can obtain
and enable the required clock(s).
Only interconnects that have clock‑gated QoS register interface
use this property; it is not applicable to all interconnect nodes.
Signed-off-by: Odelu Kukatla <odelu.kukatla@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://msgid.link/20260127090116.1438780-2-odelu.kukatla@oss.qualcomm.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Mahua is a derivative of the Glymur SoC. Extend the
Glymur driver to support Mahua by:
1. Adding new node definitions for interconnects that differ from Glymur
(Config NoC, High-Speed Coherent NoC, PCIe West ANOC/Slave NoC).
2. Reusing existing Glymur definitions for identical NoCs.
3. Overriding the channel and buswidth, with Mahua specific values for
the differing NoCs
Co-developed-by: Odelu Kukatla <odelu.kukatla@oss.qualcomm.com>
Signed-off-by: Odelu Kukatla <odelu.kukatla@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Raviteja Laggyshetty <raviteja.laggyshetty@oss.qualcomm.com>
Link: https://msgid.link/20260209-mahua_icc-v3-2-c65f3dfd72c8@oss.qualcomm.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Document the RPMh Network-on-Chip (NoC) interconnect for the Qualcomm
Mahua platform.
Mahua is a derivative of the Glymur SoC. Many interconnect nodes are
identical and continue to use Glymur fallback compatibles. Mahua
introduces SoC-specific configurations and topologies for several
NoC blocks, including CNOC, HSCNOC, PCIe West ANoC/Slave NoCs.
This updates the existing Glymur yaml schema to include Mahua-specific
compatible strings, using two-cell "fallback" compatibles wherever
the hardware is identical with Glymur.
Co-developed-by: Odelu Kukatla <odelu.kukatla@oss.qualcomm.com>
Signed-off-by: Odelu Kukatla <odelu.kukatla@oss.qualcomm.com>
Acked-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Raviteja Laggyshetty <raviteja.laggyshetty@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://msgid.link/20260209-mahua_icc-v3-1-c65f3dfd72c8@oss.qualcomm.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The FEAT_SVE2p1 is indicated by ID_AA64ZFR0_EL1.SVEver. However,
the BFADD requires the FEAT_SVE_B16B16, which is indicated by
ID_AA64ZFR0_EL1.B16B16. This could cause the test to incorrectly
fail on a CPU that supports FEAT_SVE2.1 but not FEAT_SVE_B16B16.
LD1Q Gather load quadwords which is decoded from SVE encodings and
implied by FEAT_SVE2p1.
Fixes: c5195b027d ("kselftest/arm64: Add SVE 2.1 to hwcap test")
Signed-off-by: Yifan Wu <wuyifan50@huawei.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
When a scatterlists table of a GEM shmem object of size 4 GB or more is
populated with pages allocated from a folio, unsigned int .length
attribute of a scatterlist may get overflowed if total byte length of
pages allocated to that single scatterlist happens to reach or cross the
4GB limit. As a consequence, users of the object may suffer from hitting
unexpected, premature end of the object's backing pages.
[278.780187] ------------[ cut here ]------------
[278.780377] WARNING: CPU: 1 PID: 2326 at drivers/gpu/drm/i915/i915_mm.c:55 remap_sg+0x199/0x1d0 [i915]
...
[278.780654] CPU: 1 UID: 0 PID: 2326 Comm: gem_mmap_offset Tainted: G S U 6.17.0-rc1-CI_DRM_16981-ged823aaa0607+ #1 PREEMPT(voluntary)
[278.780656] Tainted: [S]=CPU_OUT_OF_SPEC, [U]=USER
[278.780658] Hardware name: Intel Corporation Meteor Lake Client Platform/MTL-P LP5x T3 RVP, BIOS MTLPFWI1.R00.3471.D91.2401310918 01/31/2024
[278.780659] RIP: 0010:remap_sg+0x199/0x1d0 [i915]
...
[278.780786] Call Trace:
[278.780787] <TASK>
[278.780788] ? __apply_to_page_range+0x3e6/0x910
[278.780795] ? __pfx_remap_sg+0x10/0x10 [i915]
[278.780906] apply_to_page_range+0x14/0x30
[278.780908] remap_io_sg+0x14d/0x260 [i915]
[278.781013] vm_fault_cpu+0xd2/0x330 [i915]
[278.781137] __do_fault+0x3a/0x1b0
[278.781140] do_fault+0x322/0x640
[278.781143] __handle_mm_fault+0x938/0xfd0
[278.781150] handle_mm_fault+0x12c/0x300
[278.781152] ? lock_mm_and_find_vma+0x4b/0x760
[278.781155] do_user_addr_fault+0x2d6/0x8e0
[278.781160] exc_page_fault+0x96/0x2c0
[278.781165] asm_exc_page_fault+0x27/0x30
...
That issue was apprehended by the author of a change that introduced it,
and potential risk even annotated with a comment, but then never addressed.
When adding folio pages to a scatterlist table, take care of byte length
of any single scatterlist not exceeding max_segment.
Fixes: 0b62af28f2 ("i915: convert shmem_sg_free_table() to use a folio_batch")
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/14809
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@vger.kernel.org # v6.5+
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://lore.kernel.org/r/20260224094944.2447913-2-janusz.krzysztofik@linux.intel.com
When the nl80211 socket that originated a PMSR request is
closed, cfg80211_release_pmsr() sets the request's nl_portid
to zero and schedules pmsr_free_wk to process the abort
asynchronously. If the interface is concurrently torn down
before that work runs, cfg80211_pmsr_wdev_down() calls
cfg80211_pmsr_process_abort() directly. However, the already-
scheduled pmsr_free_wk work item remains pending and may run
after the interface has been removed from the driver. This
could cause the driver's abort_pmsr callback to operate on a
torn-down interface, leading to undefined behavior and
potential crashes.
Cancel pmsr_free_wk synchronously in cfg80211_pmsr_wdev_down()
before calling cfg80211_pmsr_process_abort(). This ensures any
pending or in-progress work is drained before interface teardown
proceeds, preventing the work from invoking the driver abort
callback after the interface is gone.
Fixes: 9bb7e0f24e ("cfg80211: add peer measurement with FTM initiator API")
Signed-off-by: Peddolla Harshavardhan Reddy <peddolla.reddy@oss.qualcomm.com>
Link: https://patch.msgid.link/20260305160712.1263829-3-peddolla.reddy@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
