Linus pointed out that other people have spent large amounts of time
and effort to optimize the layout of frequently used structures. Often
these have embedded locks, and the assumption is that a lock takes
4 bytes. Linus also pointed out how to work with the limited options
for atomic instructions on Itanium.
Signed-off-by: Tony Luck <tony.luck@intel.com>
CFQ enables idle only for processes that think less than the allowed
idle time. Since idle time is lower for seeky queues, we should use the
correct value in the comparison.
Signed-off-by: Corrado Zoccolo <czoccolo@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
drbd_int.h uses __ratelimit(), so it needs to #include ratelimit.h:
drivers/block/drbd/drbd_int.h:1765: error: implicit declaration of function '__ratelimit'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: drbd-dev@lists.linbit.com
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
A bug was seen on boards using a PLX 8518 switch device which advertises
AER on each of it's transparent bridges. The AER driver was loaded for
each bridge and this driver tried to access the AER source ID register
whenever an interrupt occured on the shared PCI INTX lines. The source
ID register does not exist on non root port PCIE device's which
advertise AER and trying to access this register causes a unsupported
request error on the bridge. Thus, when the next interrupt occurs,
another error is found and the non existent source ID register is
accessed again, and so it goes on.
The result is a spammed dmesg with unsupported request PCI express
errors on the bridge device that the AER driver is loaded against.
Reported-by: Malcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Malcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Found one system:
[ 71.120590] pci 0000:40:05.0: scanning behind bridge, config 4f4a40, pass 0
[ 71.138283] PCI: Scanning bus 0000:4a
[ 71.140341] pci 0000:4a:00.0: found [15b3:6278] class 000c06 header type 00
[ 71.157173] pci 0000:4a:00.0: reg 10 64bit mmio: [0x000000-0x0fffff]
[ 71.161697] pci 0000:4a:00.0: reg 18 64bit mmio pref: [0x000000-0x7fffff]
[ 71.179403] pci 0000:4a:00.0: reg 20 64bit mmio pref: [0x000000-0xfffffff]
[ 71.185366] pci 0000:4a:00.0: calling quirk_resource_alignment+0x0/0x1dd
[ 71.200846] pci 0000:4a:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 71.219623] PCI: Fixups for bus 0000:4a
[ 71.222194] pci 0000:40:05.0: bridge 32bit mmio: [0xcf000000-0xcf0fffff]
[ 71.238662] pci 0000:40:05.0: bridge 64bit mmio pref: [0xcd800000-0xcdffffff]
[ 71.255793] PCI: Bus scan for 0000:4a returning with max=4a
Device needs a big pref mmio, but BIOS doesn't allocate mmio to it aside
from a small MMIO range. Later, the kernel will not allocate resources to
that to the device:
[ 99.574030] pci 0000:4a:00.0: BAR 4: can't allocate mem resource [0xd0000000-0xcdffffff]
[ 99.580102] pci 0000:4a:00.0: BAR 2: got res [0xcd800000-0xcdffffff] bus [0xcd800000-0xcdffffff] flags 0x12120c
[ 99.602307] pci 0000:4a:00.0: BAR 2: moved to bus [0xcd800000-0xcdffffff] flags 0x12120c
[ 99.615991] pci 0000:4a:00.0: BAR 0: got res [0xcf000000-0xcf0fffff] bus [0xcf000000-0xcf0fffff] flags 0x120204
[ 99.634499] pci 0000:4a:00.0: BAR 0: moved to bus [0xcf000000-0xcf0fffff] flags 0x120204
[ 99.654318] pci 0000:40:05.0: PCI bridge, secondary bus 0000:4a
[ 99.658766] pci 0000:40:05.0: IO window: disabled
[ 99.675478] pci 0000:40:05.0: MEM window: 0xcf000000-0xcf0fffff
[ 99.681663] pci 0000:40:05.0: PREFETCH window: 0x000000cd800000-0x000000cdffffff
So try to get a big range in the pci bridge if there is no child using
that range. With the patch we get:
[ 99.104525] pci 0000:4a:00.0: BAR 4: got res [0xfc080000000-0xfc08fffffff] bus [0xfc080000000-0xfc08fffffff] flags 0x12120c
[ 99.123624] pci 0000:4a:00.0: BAR 4: moved to bus [0xfc080000000-0xfc08fffffff] flags 0x12120c
[ 99.131977] pci 0000:4a:00.0: BAR 2: got res [0xfc090000000-0xfc0907fffff] bus [0xfc090000000-0xfc0907fffff] flags 0x12120c
[ 99.149788] pci 0000:4a:00.0: BAR 2: moved to bus [0xfc090000000-0xfc0907fffff] flags 0x12120c
[ 99.169248] pci 0000:4a:00.0: BAR 0: got res [0xc0200000-0xc02fffff] bus [0xc0200000-0xc02fffff] flags 0x120204
[ 99.189508] pci 0000:4a:00.0: BAR 0: moved to bus [0xc0200000-0xc02fffff] flags 0x120204
[ 99.206402] pci 0000:40:05.0: PCI bridge, secondary bus 0000:4a
[ 99.210637] pci 0000:40:05.0: IO window: disabled
[ 99.224856] pci 0000:40:05.0: MEM window: 0xc0200000-0xc03fffff
[ 99.230019] pci 0000:40:05.0: PREFETCH window: 0x000fc080000000-0x000fc097ffffff
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This quirk will disable fast back to back transfer on the secondary bus
segment of the TI Bridge.
Signed-off-by: Gabe Black <gabe.black@ni.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
I've rewritten the extract-ikconfig script to extract the kernel
configuration from a kernel compiled with CONFIG_IKCONFIG. The main
motivation for the rewrite was to remove the dependency on the
external C program binoffset.c, which is compiled on the initial run.
The binoffset executable is invoked with a relative path, which means
that the old script can only be run from the top of the kernel tree,
and only when you have write permission in the scripts directory.
The new script uses tr/grep/tail/zcat only, and can be invoked from
anywhere. The binoffset.c program has been removed. This script
requires GNU grep 2.5 (released 2002-03-13) or higher, because the -o
option was introduced in that version.
Signed-off-by: Dick Streefland <dick@streefland.net>
LKML-Reference: <20091006203540.GA14634@streefland.net>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When injecting DRAM ECC errors (F3xBC_x8), EccVector[15:0] is a bitmask
of which bits should be error injected when written to and holds the
payload of 16-bit DRAM word when read, respectively.
Add /sysfs members to show the DRAM ECC section/word/vector.
Fail wrong injection values entered over /sysfs instead of truncating
them.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
On Fam10h and above, F1x[1, 0][7C:40] are DRAM Base/Limit registers
which specify the destination node of a DRAM address. Those address
boundaries are being extracted into ->dram_base[] and ->dram_limit[].
Correct the extraction masks to match the respective address bits.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Different processor families support a different number of chip selects.
Handle this in a family-dependent way with the proper values assigned at
init time (see amd64_set_dct_base_and_mask).
Remove _DCSM_COUNT defines since they're used at one place and originate
from public documentation.
CC: Keith Mannthey <kmannth@us.ibm.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This allows the errors to be further decoded and mapped to csrows.
Tested with ECC debug dimms and an Rev F cpu based system.
Signed-off-by: Keith Mannthey <kmannth@us.ibm.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The check when DRAM interleaving is enabled should be done against the
pvt->dram_IntlvSel field and not against the ->dram_limit.
Simplify first loop and fixup printk formatting while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The pvt->dram_IntlvEn saves the 3 "Interleave Enable" bits already
right-shifted by 8 so the check in find_mc_by_sys_addr() by shifting the
values to the left 8 bits is wrong.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
K8 DRAM base and limit addresses from F1x40 +8*i and F1x44 + 8*i, where
i in (0..7) are both bits 39-24 and therefore the shifting should be
done by 24 and not by 8.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Allocate memory statically for 8-node machines max for simplicity
instead of relying on MAX_NUMNODES which is 0 on !CONFIG_NUMA builds.
Spotted by Jan Beulich.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Since patch_alc268() doesn't call set_capture_mixer() (due to its h/w
design different from other siblings), it needs to call fixup_automic_adc()
explicitly to set up the auto-mic routing. Otherwise the indices for
int/ext mics aren't set properly.
Reference: Novell bnc#544899
http://bugzilla.novell.com/show_bug.cgi?id=544899
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change the #define's for the EP93XX_*_PHYS_BASE addresses to use
macros for easier readability.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add Contec Micro9-Slim support
Cc: Ryan Mallon <ryan@bluewatersys.com>
Requires: 5750/1
Signed-off-by: Hubert Feurstein <hubert.feurstein@contec.at>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Both iPaqs h3100 and h3600 currently share the same source
file - h3600.c But Makefile builds it only if CONFIG_SA1100_H3600
selected, so selecting just CONFIG_SA1100_H3100 results in
"no machine record defined" message and aborted compilation.
Fix it.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the warning messages during kernel build for bcmring.
Signed-off-by: Leo Hao Chen <leochen@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If sparsemem is enabled, the start_pfn passed to the free_memmap()
function corresponds to an area of memory not known to the kernel and
pfn_to_page returns a wrong value. The (start_pfn - 1), however, is
known to the kernel.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is needed because applications using the sys_cacheflush system call
can pass a memory range which isn't mapped yet even though the
corresponding vma is valid. The patch also adds unwinding annotations
for correct backtraces from the coherent_user_range() functions.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Ryan Mallon <ryan@bluewatersys.com>
Change the gpio_to_irq and irq_to_gpio static inline functions to
macros so that they can be used in variable initialisers.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds the missing Kconfig options for the first SDRAM bank address
on ep93xx boards.
Cc: Hubert Feurstein <(address hidden)>
Signed-off-by: H Hartley Sweeten <(address hidden)>
Acked-by: Ryan Mallon <(address hidden)>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 24df31acaf.
The root cause of reported system hangs was (now fixed) sis5513 bug
and not "ide: try to use PIO Mode 0 during probe if possible" change
(commit 6029336426) so the revert was
incorrect (it simply replaced one regression with the other one).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear prefetch setting before potentially (re-)enabling it in
config_drive_art_rwp() so the transition of the device type on
the port from ATA to ATAPI (i.e. during warm-plug operation)
is handled correctly.
This is a really old bug (it probably goes back to very early
days of the driver) but it was only affecting warm-plug operation
until the recent "ide: try to use PIO Mode 0 during probe if
possible" change (commit 6029336426).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tested-by: David Fries <david@fries.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f2e21c9610 had unfortunate side
effects with cpufreq governors on some systems.
If the system did not switch into NOHZ mode ts->inidle is not set when
tick_nohz_stop_sched_tick() is called from the idle routine. Therefor
all subsequent calls from irq_exit() to tick_nohz_stop_sched_tick()
fail to call tick_nohz_start_idle(). This results in bogus idle
accounting information which is passed to cpufreq governors.
Set the inidle flag unconditionally of the NOHZ active state to keep
the idle time accounting correct in any case.
[ tglx: Added comment and tweaked the changelog ]
Reported-by: Steven Noonan <steven@uplinklabs.net>
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Greg KH <greg@kroah.com>
Cc: Steven Noonan <steven@uplinklabs.net>
Cc: stable@kernel.org
LKML-Reference: <1254907901.30157.93.camel@eenurkka-desktop>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Drop remapping of netlink classes and bypass of permission checking
based on netlink message type for policy version < 18. This removes
compatibility code introduced when the original single netlink
security class used for all netlink sockets was split into
finer-grained netlink classes based on netlink protocol and when
permission checking was added based on netlink message type in Linux
2.6.8. The only known distribution that shipped with SELinux and
policy < 18 was Fedora Core 2, which was EOL'd on 2005-04-11.
Given that the remapping code was never updated to address the
addition of newer netlink classes, that the corresponding userland
support was dropped in 2005, and that the assumptions made by the
remapping code about the fixed ordering among netlink classes in the
policy may be violated in the future due to the dynamic class/perm
discovery support, we should drop this compatibility code now.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
Add a simple utility (scripts/selinux/genheaders) and invoke it to
generate the kernel-private class and permission indices in flask.h
and av_permissions.h automatically during the kernel build from the
security class mapping definitions in classmap.h. Adding new kernel
classes and permissions can then be done just by adding them to classmap.h.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
Modify SELinux to dynamically discover class and permission values
upon policy load, based on the dynamic object class/perm discovery
logic from libselinux. A mapping is created between kernel-private
class and permission indices used outside the security server and the
policy values used within the security server.
The mappings are only applied upon kernel-internal computations;
similar mappings for the private indices of userspace object managers
is handled on a per-object manager basis by the userspace AVC. The
interfaces for compute_av and transition_sid are split for kernel
vs. userspace; the userspace functions are distinguished by a _user
suffix.
The kernel-private class indices are no longer tied to the policy
values and thus do not need to skip indices for userspace classes;
thus the kernel class index values are compressed. The flask.h
definitions were regenerated by deleting the userspace classes from
refpolicy's definitions and then regenerating the headers. Going
forward, we can just maintain the flask.h, av_permissions.h, and
classmap.h definitions separately from policy as they are no longer
tied to the policy values. The next patch introduces a utility to
automate generation of flask.h and av_permissions.h from the
classmap.h definitions.
The older kernel class and permission string tables are removed and
replaced by a single security class mapping table that is walked at
policy load to generate the mapping. The old kernel class validation
logic is completely replaced by the mapping logic.
The handle unknown logic is reworked. reject_unknown=1 is handled
when the mappings are computed at policy load time, similar to the old
handling by the class validation logic. allow_unknown=1 is handled
when computing and mapping decisions - if the permission was not able
to be mapped (i.e. undefined, mapped to zero), then it is
automatically added to the allowed vector. If the class was not able
to be mapped (i.e. undefined, mapped to zero), then all permissions
are allowed for it if allow_unknown=1.
avc_audit leverages the new security class mapping table to lookup the
class and permission names from the kernel-private indices.
The mdp program is updated to use the new table when generating the
class definitions and allow rules for a minimal boot policy for the
kernel. It should be noted that this policy will not include any
userspace classes, nor will its policy index values for the kernel
classes correspond with the ones in refpolicy (they will instead match
the kernel-private indices).
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
Only 128 buffer descriptors are supported in the core. Limit the
number in case we have more memory.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enabled the ethoc to allocate system memory as buffer
when there is no dedicated buffer memory.
Some hardware designs may not have dedicated buffer memory such as
on chip or off chip SRAM. In this case, only one memory resource is
supplied in the platform data instead of two. Then a DMA buffer can
be allocated from system memory and used for the transfer.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet buffer is allocated at 4 bytes boundary, but the IP header
length and version bits is located at byte 14. These bit fields access
as 32 bits word and caused exception on processors that do not support
unaligned access.
The patch adds 2 bytes offset to make the bit fields word aligned.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer address in buffer descriptors is physical address. The
pointer that processor used to access packet is virtual address.
Though the higher bits of pointer address used by the MAC may be
truncated to zero in special case, it is not always true in larger
designs.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should be max() instead of min(). Use 1/4 of available
descriptors for tx, and there should be at least 2 tx
descriptors.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
in update_rx_stats() the RX_OVERLEN bit is set twice, replace it by RX_RUNT.
in au1000_rx() the RX_MISSED_FRAME bit was tested a few lines earlier already
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The closing parenthesis was not on the right location.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all pasemi mac interfaces can have a phy attached.
For example, XAUI has no phy and phydev is NULL for it.
In this case ethtool get settings causes kernel crash.
Fix it by returning -EOPNOTSUPP if there's no PHY attached.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I was getting ribbed about this earlier, so I figured I'd make it
official. Add myself as the maintainer of the drop monitor bits, so
people don't just gripe at Dave when it breaks (I'm sure it will never
break, but just in case :) ).
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Radensky noted that chip resets were generating stack trace dumps.
This is because the driver is attempting to acquire the mdio bus mutex
while holding the tp->lock spinlock. The fix is to change the code such
that every phy access takes the tp->lock spinlock instead.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like a typo, FUTEX_WAKE_BITS should be FUTEX_WAIT_BITSET.
Signed-off-by: Anton Blanchard <anton@samba.org>
LKML-Reference: <20091007001358.GE16073@kryten>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This fixes a bug with arp_notify.
If arp_notify is enabled, kernel will crash if address is changed
and no IP address is assigned.
http://bugzilla.kernel.org/show_bug.cgi?id=14330
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
adapter doesnot need to maintain a copy of net_device_stats.
Use the one already available in net_device. This patch takes care of the same.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like the big Kconfig cache split/rename missed one spot in the SMP
cache lock headers.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The cplbinfo was using d_path() to figure out which cpu/cplb was being
parsed. As Al pointed out, this isn't exactly reliable as it assumes the
static VFS path to be unchanged, and it's just poor form. So use the
proc_create_data() to properly (and internally) pass the exact cpu/cplb
requested to the parser function.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
