- Allow multiple functions with INTA.
- Removed the condition to allow only one vpath with INTA
- Ensure that the alarm bit in titan_mask_all_int register is cleared when
driver exits.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Added a function to check if FCS stripping is disabled by the firmware, if
it is not disabled fail driver load.
- By default FCS stripping is disabled by the firmware. With this assumption
driver decrements the indicated packet length by 4 bytes(FCS length).
- This patch ensures that FCS stripping is disabled during driver load time.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Removed the wrr_rebalance function
- This feature is not supported by the ASIC, hence removing the related code.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix a crash in PAE system due to wrong typecasting.
- On PAE system size_t is unsigned int which is 32bit. Avoid casting
64 bit address to 32 bit
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Removed accessing GENDMA_INT register
- This allowed the firmware to perform a generic DMA write to host memory.
This feature is not supported by the ASIC, this patch removes access to
GENDMA_INT register.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Update driver_config->vpath_per_dev for each function in probe.
- vpath_per_device specifies number of vpaths supported for each function/device. The
current code was updating vpath_per_device only for physical device, however this has
to be updated for each function also in case of a MF(Multi function) device.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- vxge driver was assuming function-0 is always the privilaged function. Now that
restriction has been removed any function can act as a privilaged function.
- This patch modifies the __vxge_hw_device_is_privilaged routine to not assume
function-0 as the privileged function.
- Recreated the patch by incorporating review comments from Dave Miller to
remove double slash in path names.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some switches that will do write combining when they see two
sequential regions written. In order to avoid any possible write combining
issues it is necessary to add a flush after writing each piece of a rar
register.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This update adds additional exception handling to the phy code to handle
situations where it may be called incorrectly. In addition it adds some
bounds checking to the cable length checks to prevent an array overrun in
the event that the hardware returned a different value than expected.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a retry to phy reads in the event of failure. The original
code broke out of the loop on failure and this is a mistake as we should be
trying to do the read twice.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the generic portion of the copper link setup into a
seperate function in e1000_phy.c. This helps to reduce the size of
copper_link_setup_82575 and make it a bit more readable.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
igb doesn't have any devices that use a microwire interface for NVM. As
such the code related to this can be removed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows us to treat the alternate mac address as though it is the
physical address on the adapter. This is accomplished by letting the
alt_mac_address function to only fail on an NVM error. If no errors occur
and the alternate mac address is not present then RAR0 is read as the
default mac address.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mailbox timeout routines need to be updated as they were not correctly
handling the case of a mailbox timeout and could cause issues with long
delays when used.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both the read and write mailbox functions need to acquire the mailbox lock.
Since that is the case we might as well combine both of the procedures into
one function so it is easier to maintain.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the device ID necessary to support the 82576NS SerDes
adapter.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support functions such as vlan tag stripping when SR-IOV is
enabled any given packet must match at least one filter. However in the
case of promiscous mode being enabled on the PF the traffic routed to it
may not match any filters and is just sent to the PF by default. In order
to make certain that this traffic is processed we can set all bits in the
UTA registers to create a pseudo promiscous mode filter that accepts all
packets.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds igb_rar_qsel which sets the mac address and pool bits for a
given mac address in the receive address register table.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation of sgmii support isn't correctly locking the
interfaces for reads/writes. This change pulls the read/write
functionality out of 82575.c and moves it to phy.c. In addition it
replaces the implementation in 82575.c with one that uses locking around
the relocated i2c interface calls.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current approach is just using a ?: type mechanism to set the phy
locking bit. This if fine for now but limits us to only 2. Switch to a
nested if statement for future compatiblity with more than 2 phys.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This update corrects the driver so that it handles duplex for serdes links
correctly instead of just forcing full duplex always.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a temp variable in the stats clearing path that isn't needed since
the results from the stats read can be immediately discared. Since it
isn't needed we might as well just drop it from the function call.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a typo which causes try_location() to use the wrong length argument
when calling nfs_parse_server_name(). This again, causes the initialisation
of the mount's sockaddr structure to fail.
Also ensure that if nfs4_pathname_string() returns an error, then we pass
that error back up the stack instead of ENOENT.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
As seen in <http://bugs.debian.org/549002>, nfs4_init_client() can
overrun the source string when copying the client IP address from
nfs_parsed_mount_data::client_address to nfs_client::cl_ipaddr. Since
these are both treated as null-terminated strings elsewhere, the copy
should be done with strlcpy() not memcpy().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The recent changeset 53a0b9c4c9 (NFS: Replace
nfs_parse_ip_address() with rpc_pton()) broke nfs_remount, since the call
to rpc_pton() will zero out the port number in data->nfs_server.address.
This is actually due to a bug in nfs_remount: it should be looking at the
port number in nfs_server.port instead...
This fixes bug
http://bugzilla.kernel.org/show_bug.cgi?id=14276
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Currently, the port and mount port will both display as 65535 if you do not
specify a port number. That would be wrong...
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
With the recent spate of changes, the nfs protocol version will now default
to 2 instead of 3, while the mount protocol version defaults to 3.
The following patch should ensure the defaults are consistent with the
previous defaults of vers=3,proto=tcp,mountvers=3,mountproto=tcp.
This fixes the bug
http://bugzilla.kernel.org/show_bug.cgi?id=14259
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We should subtract the slice residual from the rb tree key, since
a negative residual count indicates that the cfqq overran its slice
the last time. Hence we want to add the overrun time, to position
it a bit further away in the service tree.
Reported-by: Corrado Zoccolo <czoccolo@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Basic state information is available via /sys/kernel/debug/ceph,
including instances of the client, fsids, current monitor, mds and osd
maps, outstanding server requests, and hooks to adjust debug levels.
Signed-off-by: Sage Weil <sage@newdream.net>
A few Ceph ioctls for getting and setting file layout (striping)
parameters, and learning the identity and network address of the OSD a
given region of a file is stored on.
Signed-off-by: Sage Weil <sage@newdream.net>
Basic NFS re-export support is included. This mostly works. However,
Ceph's MDS design precludes the ability to generate a (small)
filehandle that will be valid forever, so this is of limited utility.
Signed-off-by: Sage Weil <sage@newdream.net>
The msgpool is a basic mempool_t-like structure to preallocate
messages we expect to receive over the wire. This ensures we have the
necessary memory preallocated to process replies to requests, or to
process unsolicited messages from various servers.
Signed-off-by: Sage Weil <sage@newdream.net>
A generic message passing library is used to communicate with all
other components in the Ceph file system. The messenger library
provides ordered, reliable delivery of messages between two nodes in
the system.
This implementation is based on TCP.
Signed-off-by: Sage Weil <sage@newdream.net>
Ceph snapshots rely on client cooperation in determining which
operations apply to which snapshots, and appropriately flushing
snapshotted data and metadata back to the OSD and MDS clusters.
Because snapshots apply to subtrees of the file hierarchy and can be
created at any time, there is a fair bit of bookkeeping required to
make this work.
Portions of the hierarchy that belong to the same set of snapshots
are described by a single 'snap realm.' A 'snap context' describes
the set of snapshots that exist for a given file or directory.
Signed-off-by: Sage Weil <sage@newdream.net>
The Ceph metadata servers control client access to inode metadata and
file data by issuing capabilities, granting clients permission to read
and/or write both inode field and file data to OSDs (storage nodes).
Each capability consists of a set of bits indicating which operations
are allowed.
If the client holds a *_SHARED cap, the client has a coherent value
that can be safely read from the cached inode.
In the case of a *_EXCL (exclusive) or FILE_WR capabilities, the client
is allowed to change inode attributes (e.g., file size, mtime), note
its dirty state in the ceph_cap, and asynchronously flush that
metadata change to the MDS.
In the event of a conflicting operation (perhaps by another client),
the MDS will revoke the conflicting client capabilities.
In order for a client to cache an inode, it must hold a capability
with at least one MDS server. When inodes are released, release
notifications are batched and periodically sent en masse to the MDS
cluster to release server state.
Signed-off-by: Sage Weil <sage@newdream.net>
The monitor cluster is responsible for managing cluster membership
and state. The monitor client handles what minimal interaction
the Ceph client has with it: checking for updated versions of the
MDS and OSD maps, getting statfs() information, and unmounting.
Signed-off-by: Sage Weil <sage@newdream.net>
CRUSH is a pseudorandom data distribution function designed to map
inputs onto a dynamic hierarchy of devices, while minimizing the
extent to which inputs are remapped when the devices are added or
removed. It includes some features that are specifically useful for
storage, most notably the ability to map each input onto a set of N
devices that are separated across administrator-defined failure
domains. CRUSH is used to distribute data across the cluster of Ceph
storage nodes.
More information about CRUSH can be found in this paper:
http://www.ssrc.ucsc.edu/Papers/weil-sc06.pdf
Signed-off-by: Sage Weil <sage@newdream.net>
The OSD client is responsible for reading and writing data from/to the
object storage pool. This includes determining where objects are
stored in the cluster, and ensuring that requests are retried or
redirected in the event of a node failure or data migration.
If an OSD does not respond before a timeout expires, keepalive
messages are sent across the lossless, ordered communications channel
to ensure that any break in the TCP is discovered. If the session
does reset, a reconnection is attempted and affected requests are
resent (by the message transport layer).
Signed-off-by: Sage Weil <sage@newdream.net>
The MDS (metadata server) client is responsible for submitting
requests to the MDS cluster and parsing the response. We decide which
MDS to submit each request to based on cached information about the
current partition of the directory hierarchy across the cluster. A
stateful session is opened with each MDS before we submit requests to
it, and a mutex is used to control the ordering of messages within
each session.
An MDS request may generate two responses. The first indicates the
operation was a success and returns any result. A second reply is
sent when the operation commits to disk. Note that locking on the MDS
ensures that the results of updates are visible only to the updating
client before the operation commits. Requests are linked to the
containing directory so that an fsync will wait for them to commit.
If an MDS fails and/or recovers, we resubmit requests as needed. We
also reconnect existing capabilities to a recovering MDS to
reestablish that shared session state. Old dentry leases are
invalidated.
Signed-off-by: Sage Weil <sage@newdream.net>
The ceph address space methods are concerned primarily with managing
the dirty page accounting in the inode, which (among other things)
must keep track of which snapshot context each page was dirtied in,
and ensure that dirty data is written out to the OSDs in snapshort
order.
A writepage() on a page that is not currently writeable due to
snapshot writeback ordering constraints is ignored (it was presumably
called from kswapd).
Signed-off-by: Sage Weil <sage@newdream.net>
File open and close operations, and read and write methods that ensure
we have obtained the proper capabilities from the MDS cluster before
performing IO on a file. We take references on held capabilities for
the duration of the read/write to avoid prematurely releasing them
back to the MDS.
We implement two main paths for read and write: one that is buffered
(and uses generic_aio_{read,write}), and one that is fully synchronous
and blocking (operating either on a __user pointer or, if O_DIRECT,
directly on user pages).
Signed-off-by: Sage Weil <sage@newdream.net>
Directory operations, including lookup, are defined here. We take
advantage of lookup intents when possible. For the most part, we just
need to build the proper requests for the metadata server(s) and
pass things off to the mds_client.
The results of most operations are normally incorporated into the
client's cache when the reply is parsed by ceph_fill_trace().
However, if the MDS replies without a trace (e.g., when retrying an
update after an MDS failure recovery), some operation-specific cleanup
may be needed.
We can validate cached dentries in two ways. A per-dentry lease may
be issued by the MDS, or a per-directory cap may be issued that acts
as a lease on the entire directory. In the latter case, a 'gen' value
is used to determine which dentries belong to the currently leased
directory contents.
We normally prepopulate the dcache and icache with readdir results.
This makes subsequent lookups and getattrs avoid any server
interaction. It also lets us satisfy readdir operation by peeking at
the dcache IFF we hold the per-directory cap/lease, previously
performed a readdir, and haven't dropped any of the resulting
dentries.
Signed-off-by: Sage Weil <sage@newdream.net>
Inode cache and inode operations. We also include routines to
incorporate metadata structures returned by the MDS into the client
cache, and some helpers to deal with file capabilities and metadata
leases. The bulk of that work is done by fill_inode() and
fill_trace().
Signed-off-by: Sage Weil <sage@newdream.net>
struct ceph_buffer is a simple ref-counted buffer. We transparently
choose between kmalloc for small buffers and vmalloc for large ones.
This is currently used only for allocating memory for xattr data.
Signed-off-by: Sage Weil <sage@newdream.net>
We first define constants, types, and prototypes for the kernel client
proper.
A few subsystems are defined separately later: the MDS, OSD, and
monitor clients, and the messaging layer.
Signed-off-by: Sage Weil <sage@newdream.net>
