At probe time, falcon_reset_hw() performs a hard reset of the PHY
along with Falcon. There is no need to perform a soft reset later,
and any access to standard MDIO registers before the PHY firmware has
booted can interrupt the boot process, making the port unusable.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs will report that the link is up even though there is a fault
condition. Therefore, check the fault flag too. We must also read
STAT2 to reset this flag.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
falcon_reset_xaui() waits for XGXS reset to complete, but the XAUI
serdes reset may take longer. It needs to check both reset active
bits.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must call netif_carrier_off() after the device is registered, not
before, to set the operational state and user-space IFF_RUNNING flag
correctly.
Since we don't want observers to see an intermediate state, open-code
register_netdev() and add efx_update_name() and netif_carrier_off()
into the locked region.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If nothing has been written into the qeth sysfs-attribute layer2,
its value is "-1" meaning "not yet defined". But the value is
displayed as "1" meaning "layer2 selected". The patch changes the
reading of this "-1"-value to "-1" to make clear the layer2-attribute
has not yet been defined.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth displayed an entry in /proc/service_level even when no valid
MCL-string was available (the MCL info is blank). The change is to
create an entry in /proc/service_level only when MCL-string is
non-zero.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear separation of cast-type determination (send path) for layer-2
resp. layer-3. Allowing to have inline functions for qeth layer-
discipline.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the IP address list contains entries (not removed when the device was set
offline) this entries should be registered next time the device is brought online.
In the past this was done implicitly with the device open call but since we wait
in the set IPv4 IPA and the device open common code holds various locks this
does not work any longer.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Qeth HiperSockets support now retries sending of packets when the
IBM System z signals a temporary resource shortage (e.g. target
buffer full). The packet is enqueued into the device queue.
After 3 times of unsuccessful send the packet is dropped.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kprobes can enter into a probing recursion, ie: a kprobe that does an
endless loop because one of its core mechanism function used during
probing is also probed itself.
This patch helps pinpointing the kprobe that raised such recursion
by dumping it and raising a BUG instead of a warning (we also disarm
the kprobe to try avoiding recursion in BUG itself). Having a BUG
instead of a warning stops the stacktrace in the right place and
doesn't pollute the logs with hundreds of traces that eventually end
up in a stack overflow.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Change trace_arg_string() and parse_trace_arg() to probe_arg_string()
and parse_probe_arg(), since those are kprobe-tracer local functions.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Frank Ch. Eigler <fche@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jason Baron <jbaron@redhat.com>
Cc: K.Prasad <prasad@linux.vnet.ibm.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Przemysław Pawełczyk <przemyslaw@pawelczyk.it>
Cc: Roland McGrath <roland@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
LKML-Reference: <20090821194351.12478.15247.stgit@localhost.localdomain>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Fix x86 instruction decoder selftest to check only .text because other
sections (e.g. .notes) will have random bytes which don't need to be
checked.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Frank Ch. Eigler <fche@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jason Baron <jbaron@redhat.com>
Cc: K.Prasad <prasad@linux.vnet.ibm.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Przemysław Pawełczyk <przemyslaw@pawelczyk.it>
Cc: Roland McGrath <roland@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
LKML-Reference: <20090821194307.12478.76938.stgit@localhost.localdomain>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Add profiling interfaces for each kprobes event. This interface provides
how many times each probe hit or missed.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Frank Ch. Eigler <fche@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: K.Prasad <prasad@linux.vnet.ibm.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Przemysław Pawełczyk <przemyslaw@pawelczyk.it>
Cc: Roland McGrath <roland@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
LKML-Reference: <20090813203541.31965.8452.stgit@localhost.localdomain>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Assign new event ids for each kprobes event. This doesn't clear
ring_buffer when unregistering each kprobe event. Thus, if you mind
'Unknown event' messages, clear the buffer manually after changing
kprobe events.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Frank Ch. Eigler <fche@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: K.Prasad <prasad@linux.vnet.ibm.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Przemysław Pawełczyk <przemyslaw@pawelczyk.it>
Cc: Roland McGrath <roland@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
LKML-Reference: <20090813203534.31965.49105.stgit@localhost.localdomain>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Generate names for each kprobe event based on the probe point.
(SYMBOL+offs or MEMADDR).
Also remove generic k*probe event types because there is no user
of those types.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Frank Ch. Eigler <fche@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: K.Prasad <prasad@linux.vnet.ibm.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Przemysław Pawełczyk <przemyslaw@pawelczyk.it>
Cc: Roland McGrath <roland@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
LKML-Reference: <20090813203526.31965.56672.stgit@localhost.localdomain>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Support up to 128 arguments to fetch for each kprobes event.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Frank Ch. Eigler <fche@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: K.Prasad <prasad@linux.vnet.ibm.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Przemysław Pawełczyk <przemyslaw@pawelczyk.it>
Cc: Roland McGrath <roland@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
LKML-Reference: <20090813203518.31965.96979.stgit@localhost.localdomain>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Add the documentation to use the kprobe based event tracer.
[fweisbec@gmail.com: Split tracer and its Documentation in two patchs]
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Frank Ch. Eigler <fche@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: K.Prasad <prasad@linux.vnet.ibm.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Przemysław Pawełczyk <przemyslaw@pawelczyk.it>
Cc: Roland McGrath <roland@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
LKML-Reference: <20090813203510.31965.29123.stgit@localhost.localdomain>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Add kprobes-based event tracer on ftrace.
This tracer is similar to the events tracer which is based on Tracepoint
infrastructure. Instead of Tracepoint, this tracer is based on kprobes
(kprobe and kretprobe). It probes anywhere where kprobes can probe(this
means, all functions body except for __kprobes functions).
Similar to the events tracer, this tracer doesn't need to be activated
via current_tracer, instead of that, just set probe points via
/sys/kernel/debug/tracing/kprobe_events. And you can set filters on each
probe events via /sys/kernel/debug/tracing/events/kprobes/<EVENT>/filter.
This tracer supports following probe arguments for each probe.
%REG : Fetch register REG
sN : Fetch Nth entry of stack (N >= 0)
sa : Fetch stack address.
@ADDR : Fetch memory at ADDR (ADDR should be in kernel)
@SYM[+|-offs] : Fetch memory at SYM +|- offs (SYM should be a data symbol)
aN : Fetch function argument. (N >= 0)
rv : Fetch return value.
ra : Fetch return address.
+|-offs(FETCHARG) : fetch memory at FETCHARG +|- offs address.
See Documentation/trace/kprobetrace.txt in the next patch for details.
Changes from v13:
- Support 'sa' for stack address.
- Use call->data instead of container_of() macro.
[fweisbec@gmail.com: Fixed conflict against latest tracing/core]
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Frank Ch. Eigler <fche@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: K.Prasad <prasad@linux.vnet.ibm.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Przemysław Pawełczyk <przemyslaw@pawelczyk.it>
Cc: Roland McGrath <roland@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
LKML-Reference: <20090813203510.31965.29123.stgit@localhost.localdomain>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Reason: Change to is_new_memtype_allowed() in x86/urgent
Resolved semantic conflicts in:
arch/x86/mm/pat.c
arch/x86/mm/ioremap.c
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Steven Rostedt has suggested that Neil work with the tracing
folks, trying to use TRACE_EVENT as the mechanism for
implementation. And if that doesn't workout we can investigate
other solutions such as that one which was tried here.
This reverts the following 2 commits:
5a165657be
("net: skb ftracer - Add config option to enable new ftracer (v3)")
9ec04da748
("net: skb ftracer - Add actual ftrace code to kernel (v3)")
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.100.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This brings the 57780's phy into IEEE compliance by suppressing the
common mode oscillation.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the AC131 fast ethernet transceiver.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the BCM50610M phy ID.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the code to use the PHY_IS_FET flag rather than the
ASIC revision to decide whether or not to use FET paths.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom's phys come in two distinctly different register layouts. For
the lack of an official term to distinguish between the two formats, we
can loosely categorize them by their fast ethernet or gigabit ethernet
transceiver description. This patch creates the (driver-internal) Fast
Ethernet Transceiver (FET) namespace and converts the 5906 EPHY
definitions over.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tunes the timeouts the CPMU uses to decide when to switch
from the clocks output by the PHY to internal clock sources.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the 57788 and removes support for the 57720
which was never released.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most older tg3 devices only supported a PCIe maximum payload size of
128 bytes. More recent devices bump this limit up to 256 bytes
though. This patch modifies the code so that the MPS limit is only
enforced on those devices that only allow the 128 byte setting.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall discovered that the TG3_FLG2_TSO_CAPABLE flag was being
compared against the wrong flags device member. This patch implements
the fix.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prevents a tx BD corruption bug by preventing the device from
powering down the PLL from L1 if the link speed is 10Mbps or 100Mbps.
The same bits are also used to prevent a system hang during chip reset
resulting from a complicated set of events that ultimately leads to
PCIe block register corruption.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes some PCIe link receiver errors by decreasing the internal
electrical idle timeout.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use TRACE_FIELD_ZERO(type, item) instead of TRACE_FIELD_ZERO_CHAR(item).
This also includes a typo fix of TRACE_ZERO_CHAR() macro.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Frank Ch. Eigler <fche@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: K.Prasad <prasad@linux.vnet.ibm.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Przemysław Pawełczyk <przemyslaw@pawelczyk.it>
Cc: Roland McGrath <roland@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
LKML-Reference: <20090813203501.31965.30172.stgit@localhost.localdomain>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Add dynamic ftrace_event_call support to ftrace. Trace engines can add
new ftrace_event_call to ftrace on the fly. Each operator function of
the call takes an ftrace_event_call data structure as an argument,
because these functions may be shared among several ftrace_event_calls.
Changes from v13:
- Define remove_subsystem_dir() always (revirt a2ca5e03), because
trace_remove_event_call() uses it.
- Modify syscall tracer because of ftrace_event_call change.
[fweisbec@gmail.com: Fixed conflict against latest tracing/core]
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Frank Ch. Eigler <fche@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: K.Prasad <prasad@linux.vnet.ibm.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Przemysław Pawełczyk <przemyslaw@pawelczyk.it>
Cc: Roland McGrath <roland@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
LKML-Reference: <20090813203453.31965.71901.stgit@localhost.localdomain>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Add sanity check for remap_pfn_range of RAM regions using
lookup_memtype(). Previously, we did not have anyway to get the type of
RAM memory regions as they were tracked using a single bit in
page_struct (WB, nonWB). Now we can get the actual type from page struct
(WB, WC, UC_MINUS) and make sure the requester gets that type.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Lookup the reserved memtype during vm_insert_pfn and use that memtype
for the new mapping. This takes care or handling of vm_insert_pfn()
interface in track_pfn_vma*/untrack_pfn_vma.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add a new routine lookup_memtype() to get the current memtype based on
the PAT reserves and frees.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Change reserve_ram_pages_type and free_ram_pages_type to use 2 page
flags to track UC_MINUS, WC, WB and default types. Previous RAM tracking
just tracked WB or NonWB, which was not complete and did not allow
tracking of RAM fully and there was no way to get the actual type
reserved by looking at the page flags.
We use the memtype_lock spinlock for atomicity in dealing with
memtype tracking in struct page.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Only IA64 was using PG_uncached as of now. We now intend to use this bit
in x86 as well, to keep track of memory type of those addresses that
have page struct for them. So, generalize the use of that bit across
ia64 and x86.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
PAT memtype tracking uses a linear link list to keep track of IO
(non-RAM) regions and their memtypes. The code used a last_accessed
pointer as a cache to speedup the lookup. As per discussions with
H. Peter Anvin a while back, having a rbtree here will avoid bad
performances in pathological cases where we may end up with huge
linked list. This may not add any noticable performance speedup
in normal case as the number of entires in PAT memtype list tend
to be ~20-30 range. The patch removes the "cached_entry" logic
as with rbtree we have more generic way of speeding up the lookup.
With this patch, we use rbtree to do the quick lookup. We still use
linked list as the memtype range tracked can be of different sizes
and can overlap in different ways. We also keep track of usage counts
with linked list.
Example:
Multiple ioremaps with different sizes
uncached-minus @ 0xfffff00000-0xfffff04000
uncached-minus @ 0xfffff02000-0xfffff03000
And one userlevel mmap and the thread forks a new process
uncached-minus @ 0xbf453000-0xbf454000
uncached-minus @ 0xbf453000-0xbf454000
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
io_mapping_* interfaces were added, mainly for graphics drivers.
Make this interface go through the PAT reserve/free, instead of
hardcoding WC mapping. This makes sure that there are no
aliases due to unconditional WC setting.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add new routines to request memtype for IO regions. This will currently
be a backend for io_mapping_* routines. But, it can also be made available
to drivers directly in future, in case it is needed.
reserve interface reserves the memory, makes sure we have a compatible
memory type available and keeps the identity map in sync when needed.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
ioremap has this hard-coded check for new type and requested type. That
check differs from other PAT users like /dev/mem mmap, remap_pfn_range
in only one condition where requested type is UC_MINUS and new type
is WC. Under that condition, ioremap fails. But other PAT interfaces succeed
with a WC mapping.
Change to make ioremap be in sync with other PAT APIs and use the same
macro as others. Also changes the error print to KERN_ERR instead of
pr_debug.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Make reserve_memtype internally take care of pat disabled case and fallback
to default return values.
Remove the specific pat_disabled checks in track_* routines.
Change kernel_map_sync_memtype to sync identity map even when
pat_disabled.
This change ensures that, even for pat_disabled case, we take care of
keeping identity map in sync. Before this patch, in pat disabled case,
ioremap() keeps the identity maps in sync and other APIs like pci and
/dev/mem mmap don't, which is not a very consistent behavior.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Remove function e1000_mta_set, as it is no longer called
Signed-off-by: Dave Graham <david.graham@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were already exporting TSO6 to the vlan, but we weren't exporting the
checksum support for IPV6 which was causing warning messages to be
displayed when doing IPv6 TSO over a vlan.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have some ~40 functions that were being called out with 'make
namespacecheck'. This patch changes these functions to be static.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>