Fix issue with Odroid HC4 (and all meson-sm1-odroid) DTS that causes
regulator power to momentarily glitch OFF-ON during boot. Add
regulator-boot-on to all regulator-fixed and regulator-gpio entries
that (1) define a gpio AND (2) define regulator-always-on.
U-boot powers on devices necessary for boot then hands off the DTB to
the kernel. During probe, linux drivers/regulator/fixed.c and
gpio-regulator.c both first set the regulator control gpio (that U-boot
already turned ON) to default OFF before then setting it to the defined
(ON) state. This glitches the power to the affected devices, unless
regulator-boot-on is specified with it. In fact, U-boot has the same
behavior. So, during reboot, a power glitch can actually happen twice:
once when U-boot reads the DTB and probes the gpio and again when the
kernel reads the DTB and probes the gpio.
Problem this fixes: On the Odroid HC4, power to the SATA ports glitches
during boot and causes some HDDs to do emergency head retract, which
should be avoided. On the HC4, power glitches to the SD card, USB,
SATA, and HDMI interfaces during boot. These are all boot devices.
A power glitch can potentially cause a problem for any sensitive devices
during boot.
NOTE: This is not limited to just the HC4, likely an issue with ALL DTS
with regulator-fixed or regulator-gpio entries that (1) define a gpio
AND (2) define regulator-always-on. All such entries should also
include regulator-boot-on in order to avoid potential power glitches.
At worst, adding regulator-boot-on in such cases is harmless because of
regulator-always-on, and, at best, it eliminates detrimental power
glitches during boot. So, this is best-practice.
Fixes: 164147f094 ("arm64: dts: meson-sm1-odroid-hc4: add regulators controlled by GPIOH_8")
Fixes: 45d736ab17 ("arm64: dts: meson-sm1-odroid: add 5v regulator gpio")
Fixes: 1f80a5cf74 ("arm64: dts: meson-sm1-odroid: add missing enable gpio and supply for tf_io regulator")
Fixes: 88d537bc92 ("arm64: dts: meson: convert meson-sm1-odroid-c4 to dtsi")
Signed-off-by: Eric Neulight <Eric.Neulight@linuxdev.slmail.me>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Viacheslav Bocharov <v@baodeep.com>
Tested-by: Ricardo Pardini <ricardo@pardini.net> # on Odroid-HC4 5V HDD
Link: https://patch.msgid.link/20260116-odroid-hc4-dts-v1-1-459b601cd5cf@linuxdev.slmail.me
[narmstrong: fixed subject prefix]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Enable the on-board eMMC storage for Khadas VIM1S.
The VIM1S features a 16GB eMMC 5.1 module. This patch adds the
necessary regulators and the eMMC controller node.
Signed-off-by: Nick Xie <nick@khadas.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://patch.msgid.link/20260116023611.2033078-1-nick@khadas.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
authencesn assumes an ESP/ESN-formatted AAD. When assoclen is shorter than
the minimum expected length, crypto_authenc_esn_decrypt() can advance past
the end of the destination scatterlist and trigger a NULL pointer dereference
in scatterwalk_map_and_copy(), leading to a kernel panic (DoS).
Add a minimum AAD length check to fail fast on invalid inputs.
Fixes: 104880a6b4 ("crypto: authencesn - Convert to new AEAD interface")
Reported-By: Taeyang Lee <0wn@theori.io>
Signed-off-by: Taeyang Lee <0wn@theori.io>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
During initialization of DRM buddy memory manager at drm_buddy_init,
mm->free_trees array is allocated for both clear and dirty RB trees.
During cleanup happening at drm_buddy_fini it is never freed, leading to
following memory leaks observed on xe module load & unload cycles:
kmemleak_alloc+0x4a/0x90
__kmalloc_cache_noprof+0x488/0x800
drm_buddy_init+0xc2/0x330 [drm_buddy]
__xe_ttm_vram_mgr_init+0xc3/0x190 [xe]
xe_ttm_stolen_mgr_init+0xf5/0x9d0 [xe]
xe_device_probe+0x326/0x9e0 [xe]
xe_pci_probe+0x39a/0x610 [xe]
local_pci_probe+0x47/0xb0
pci_device_probe+0xf3/0x260
really_probe+0xf1/0x3c0
__driver_probe_device+0x8c/0x180
driver_probe_device+0x24/0xd0
__driver_attach+0x10f/0x220
bus_for_each_dev+0x7f/0xe0
driver_attach+0x1e/0x30
bus_add_driver+0x151/0x290
Deallocate array for free trees when cleaning up buddy memory manager
in the same way as if going through out_free_tree label.
Fixes: d4cd665c98 ("drm/buddy: Separate clear and dirty free block trees")
Signed-off-by: Michał Grzelak <michal.grzelak@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Link: https://patch.msgid.link/20251208102714.4008260-2-michal.grzelak@intel.com
Currently we don't used mballoc optimized scanning (using max free
extent order and avg free extent order group lists) for inodes with
indirect block based format. This is confusing for users and I don't see
a good reason for that. Even with indirect block based inode format we
can spend big amount of time searching for free blocks for large
filesystems with fragmented free space. To add to the confusion before
commit 077d0c2c78 ("ext4: make mb_optimize_scan performance mount
option work with extents") optimized scanning was applied *only* to
indirect block based inodes so that commit appears as a performance
regression to some users. Just use optimized scanning whenever it is
enabled by mount options.
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: stable@kernel.org
Link: https://patch.msgid.link/20260114182836.14120-4-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
For filesystems with more than 2^32 blocks inodes using indirect block
based format cannot use blocks beyond the 32-bit limit.
ext4_mb_scan_groups_linear() takes care to not select these unsupported
groups for such inodes however other functions selecting groups for
allocation don't. So far this is harmless because the other selection
functions are used only with mb_optimize_scan and this is currently
disabled for inodes with indirect blocks however in the following patch
we want to enable mb_optimize_scan regardless of inode format.
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Pedro Falcato <pfalcato@suse.de>
Cc: stable@kernel.org
Link: https://patch.msgid.link/20260114182836.14120-3-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
fstests test generic/388 occasionally reproduces a warning in
ext4_put_super() associated with the dirty clusters count:
WARNING: CPU: 7 PID: 76064 at fs/ext4/super.c:1324 ext4_put_super+0x48c/0x590 [ext4]
Tracing the failure shows that the warning fires due to an
s_dirtyclusters_counter value of -1. IOW, this appears to be a
spurious decrement as opposed to some sort of leak. Further tracing
of the dirty cluster count deltas and an LLM scan of the resulting
output identified the cause as a double decrement in the error path
between ext4_mb_mark_diskspace_used() and the caller
ext4_mb_new_blocks().
First, note that generic/388 is a shutdown vs. fsstress test and so
produces a random set of operations and shutdown injections. In the
problematic case, the shutdown triggers an error return from the
ext4_handle_dirty_metadata() call(s) made from
ext4_mb_mark_context(). The changed value is non-zero at this point,
so ext4_mb_mark_diskspace_used() does not exit after the error
bubbles up from ext4_mb_mark_context(). Instead, the former
decrements both cluster counters and returns the error up to
ext4_mb_new_blocks(). The latter falls into the !ar->len out path
which decrements the dirty clusters counter a second time, creating
the inconsistency.
To avoid this problem and simplify ownership of the cluster
reservation in this codepath, lift the counter reduction to a single
place in the caller. This makes it more clear that
ext4_mb_new_blocks() is responsible for acquiring cluster
reservation (via ext4_claim_free_clusters()) in the !delalloc case
as well as releasing it, regardless of whether it ends up consumed
or returned due to failure.
Fixes: 0087d9fb3f ("ext4: Fix s_dirty_blocks_counter if block allocation failed with nodelalloc")
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Link: https://patch.msgid.link/20260113171905.118284-1-bfoster@redhat.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
The xfstests' test-case generic/037 fails to execute
correctly:
FSTYP -- hfsplus
PLATFORM -- Linux/x86_64 hfsplus-testing-0001 6.15.0-rc4+ #8 SMP PREEMPT_DYNAMIC Thu May 1 16:43:22 PDT 2025
MKFS_OPTIONS -- /dev/loop51
MOUNT_OPTIONS -- /dev/loop51 /mnt/scratch
generic/037 - output mismatch (see xfstests-dev/results//generic/037.out.bad)
The goal of generic/037 test-case is to "verify that replacing
a xattr's value is an atomic operation". The test "consists of
removing the old value and then inserting the new value in a btree.
This made readers (getxattr and listxattrs) not getting neither
the old nor the new value during a short time window".
The HFS+ has the issue of executing the xattr replace operation
because __hfsplus_setxattr() method [1] implemented it as not
atomic operation [2]:
if (hfsplus_attr_exists(inode, name)) {
if (flags & XATTR_CREATE) {
pr_err("xattr exists yet\n");
err = -EOPNOTSUPP;
goto end_setxattr;
}
err = hfsplus_delete_attr(inode, name);
if (err)
goto end_setxattr;
err = hfsplus_create_attr(inode, name, value, size);
if (err)
goto end_setxattr;
}
The main issue of the logic that it implements delete and
create of xattr as independent atomic operations, but the replace
operation at whole is not atomic operation. This patch implements
a new hfsplus_replace_attr() method that makes the xattr replace
operation by atomic one. Also, it reworks hfsplus_create_attr() and
hfsplus_delete_attr() with the goal of reusing the common logic
in hfsplus_replace_attr() method.
sudo ./check generic/037
FSTYP -- hfsplus
PLATFORM -- Linux/x86_64 hfsplus-testing-0001 6.19.0-rc1+ #47 SMP PREEMPT_DYNAMIC Thu Jan 8 15:37:20 PST 2026
MKFS_OPTIONS -- /dev/loop51
MOUNT_OPTIONS -- /dev/loop51 /mnt/scratch
generic/037 37s ... 37s
Ran: generic/037
Passed all 1 tests
[1] https://elixir.bootlin.com/linux/v6.19-rc4/source/fs/hfsplus/xattr.c#L261
[2] https://elixir.bootlin.com/linux/v6.19-rc4/source/fs/hfsplus/xattr.c#L338
Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
cc: Yangtao Li <frank.li@vivo.com>
cc: linux-fsdevel@vger.kernel.org
Link: https://lore.kernel.org/r/20260109234213.2805400-1-slava@dubeyko.com
Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
s_fc_lock can be acquired from inode eviction and thus is
reclaim unsafe. Since the fast commit path holds s_fc_lock while writing
the commit log, allocations under the lock can enter reclaim and invert
the lock order with fs_reclaim. Add ext4_fc_lock()/ext4_fc_unlock()
helpers which acquire s_fc_lock under memalloc_nofs_save()/restore()
context and use them everywhere so allocations under the lock cannot
recurse into filesystem reclaim.
Fixes: 6593714d67 ("ext4: hold s_fc_lock while during fast commit")
Signed-off-by: Li Chen <me@linux.beauty>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20260106120621.440126-1-me@linux.beauty
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
A bitmap inconsistency issue was observed during stress tests under
mixed huge-page workloads. Ext4 reported multiple e4b bitmap check
failures like:
ext4_mb_complex_scan_group:2508: group 350, 8179 free clusters as
per group info. But got 8192 blocks
Analysis and experimentation confirmed that the issue is caused by a
race condition between page migration and bitmap modification. Although
this timing window is extremely narrow, it is still hit in practice:
folio_lock ext4_mb_load_buddy
__migrate_folio
check ref count
folio_mc_copy __filemap_get_folio
folio_try_get(folio)
......
mb_mark_used
ext4_mb_unload_buddy
__folio_migrate_mapping
folio_ref_freeze
folio_unlock
The root cause of this issue is that the fast path of load_buddy only
increments the folio's reference count, which is insufficient to prevent
concurrent folio migration. We observed that the folio migration process
acquires the folio lock. Therefore, we can determine whether to take the
fast path in load_buddy by checking the lock status. If the folio is
locked, we opt for the slow path (which acquires the lock) to close this
concurrency window.
Additionally, this change addresses the following issues:
When the DOUBLE_CHECK macro is enabled to inspect bitmap-related
issues, the following error may be triggered:
corruption in group 324 at byte 784(6272): f in copy != ff on
disk/prealloc
Analysis reveals that this is a false positive. There is a specific race
window where the bitmap and the group descriptor become momentarily
inconsistent, leading to this error report:
ext4_mb_load_buddy ext4_mb_load_buddy
__filemap_get_folio(create|lock)
folio_lock
ext4_mb_init_cache
folio_mark_uptodate
__filemap_get_folio(no lock)
......
mb_mark_used
mb_mark_used_double
mb_cmp_bitmaps
mb_set_bits(e4b->bd_bitmap)
folio_unlock
The original logic assumed that since mb_cmp_bitmaps is called when the
bitmap is newly loaded from disk, the folio lock would be sufficient to
prevent concurrent access. However, this overlooks a specific race
condition: if another process attempts to load buddy and finds the folio
is already in an uptodate state, it will immediately begin using it without
holding folio lock.
Signed-off-by: Yongjian Sun <sunyongjian1@huawei.com>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20260106090820.836242-1-sunyongjian@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
We do not use EXT4_GET_BLOCKS_IO_CREATE_EXT or split extents before
submitting I/O; therefore, remove the related code.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://patch.msgid.link/20260105014522.1937690-8-yi.zhang@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
In the write path mapping check of ext4_iomap_begin(), the return value
'ret' should never greater than orig_mlen. If 'ret' equals 'orig_mlen',
it can be returned directly without checking IOMAP_ATOMIC.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://patch.msgid.link/20260105014522.1937690-7-yi.zhang@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The parameter unwritten in ext4_dio_write_iter() is no longer needed,
simply remove it.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://patch.msgid.link/20260105014522.1937690-6-yi.zhang@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
ext4_iomap_overwrite_ops was introduced in commit 8cd115bdda ("ext4:
Optimize ext4 DIO overwrites"), which can optimize pure overwrite
performance by dropping the IOMAP_WRITE flag to only query the mapped
mapping information. This avoids starting a new journal handle, thereby
improving speed. Later, commit 9faac62d40 ("ext4: optimize file
overwrites") also optimized similar scenarios, but it performs the check
later, examining the mappings status only when the actual block mapping
is needed. Thus, it can handle the previous commit scenario. That means
in the case of an overwrite scenario, the condition
"offset + length <= i_size_read(inode)" in the write path must always be
true.
Therefore, it is acceptable to remove the ext4_iomap_overwrite_ops,
which will also clarify the write and read paths of ext4_iomap_begin.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://patch.msgid.link/20260105014522.1937690-5-yi.zhang@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Since we have deferred the split of the unwritten extent until after I/O
completion, it is not necessary to initiate the journal handle when
submitting the I/O.
This can improve the write performance of concurrent DIO for multiple
files. The fio tests below show a ~25% performance improvement when
wirting to unwritten files on my VM with a mem disk.
[unwritten]
direct=1
ioengine=psync
numjobs=16
rw=write # write/randwrite
bs=4K
iodepth=1
directory=/mnt
size=5G
runtime=30s
overwrite=0
norandommap=1
fallocate=native
ramp_time=5s
group_reporting=1
[w/o]
w: IOPS=62.5k, BW=244MiB/s
rw: IOPS=56.7k, BW=221MiB/s
[w]
w: IOPS=79.6k, BW=311MiB/s
rw: IOPS=70.2k, BW=274MiB/s
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://patch.msgid.link/20260105014522.1937690-4-yi.zhang@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Currently, when writing back dirty pages to the filesystem with the
dioread_nolock feature enabled and when doing DIO, if the area to be
written back is part of an unwritten extent, the
EXT4_GET_BLOCKS_IO_CREATE_EXT flag is set during block allocation before
submitting I/O. The function ext4_split_convert_extents() then attempts
to split this extent in advance. This approach is designed to prevents
extent splitting and conversion to the written type from failing due to
insufficient disk space at the time of I/O completion, which could
otherwise result in data loss.
However, we already have two mechanisms to ensure successful extent
conversion. The first is the EXT4_GET_BLOCKS_METADATA_NOFAIL flag, which
is a best effort, it permits the use of 2% of the reserved space or
4,096 blocks in the file system when splitting extents. This flag covers
most scenarios where extent splitting might fail. The second is the
EXT4_EXT_MAY_ZEROOUT flag, which is also set during extent splitting. If
the reserved space is insufficient and splitting fails, it does not
retry the allocation. Instead, it directly zeros out the extra part of
the extent, thereby avoiding splitting and directly converting the
entire extent to the written type.
These two mechanisms also exist when I/Os are completed because there is
a concurrency window between write-back and fallocate, which may still
require us to split extents upon I/O completion. There is no much
difference between splitting extents before submitting I/O. Therefore,
It seems possible to defer the splitting until I/O completion, it won't
increase the risk of I/O failure and data loss. On the contrary, if some
I/Os can be merged when I/O completion, it can also reduce unnecessary
splitting operations, thereby alleviating the pressure on reserved
space.
In addition, deferring extent splitting until I/O completion can
also simplify the IO submission process and avoid initiating unnecessary
journal handles when writing unwritten extents.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://patch.msgid.link/20260105014522.1937690-3-yi.zhang@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
When performing buffered writes, we may need to split and convert an
unwritten extent into a written one during the end I/O process. However,
we do not reserve space specifically for these metadata changes, we only
reserve 2% of space or 4096 blocks. To address this, we use
EXT4_GET_BLOCKS_PRE_IO to potentially split extents in advance and
EXT4_GET_BLOCKS_METADATA_NOFAIL to utilize reserved space if necessary.
These two approaches can reduce the likelihood of running out of space
and losing data. However, these methods are merely best efforts, we
could still run out of space, and there is not much difference between
converting an extent during the writeback process and the end I/O
process, it won't increase the risk of losing data if we postpone the
conversion.
Therefore, also use EXT4_GET_BLOCKS_METADATA_NOFAIL in
ext4_convert_unwritten_extents_endio() to prepare for the buffered I/O
iomap conversion, which may perform extent conversion during the end I/O
process.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://patch.msgid.link/20260105014522.1937690-2-yi.zhang@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
In ext4_ext_shift_extents(), if the extent is NULL in the while loop, the
function returns immediately without releasing the path obtained via
ext4_find_extent(), leading to a memory leak.
Fix this by jumping to the out label to ensure the path is properly
released.
Fixes: a18ed359bd ("ext4: always check ext4_ext_find_extent result")
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Link: https://patch.msgid.link/20251225084800.905701-1-zilin@seu.edu.cn
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
When zeroing out a written partial block, it is necessary to order the
data to prevent exposing stale data on disk. However, if the buffer is
unwritten or delayed, it is not allocated as written, so ordering the
data is not required. This can prevent strange and unnecessary ordered
writes when appending data across a region within a block.
Assume we have a 2K unwritten file on a filesystem with 4K blocksize,
and buffered write from 3K to 4K. Before this patch,
__ext4_block_zero_page_range() would add the range [2k,3k) to the
ordered range, and then the JBD2 commit process would write back this
block. However, it does nothing since the block is not mapped as
written, this folio will be redirtied and written back agian through the
normal write back process.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Link: https://patch.msgid.link/20251223011927.34042-1-yi.zhang@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Storing of the iw->head entry inside the wait_queue callback, or when
removing a waitid item, really should use proper load/store
acquire/release semantics, and KCSAN correctly warns of that. Ensure
that they do so.
Reported-by: syzbot+eb441775f4f948a0902f@syzkaller.appspotmail.com
Fixes: a48c0cbf28 ("io_uring/waitid: have io_waitid_complete() remove wait queue entry")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The d_path function does not require the caller to pre-zero the
buffer.
Signed-off-by: pengdonglin <pengdonglin@xiaomi.com>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Link: https://patch.msgid.link/20251211123829.2777009-1-dolinux.peng@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
"b" is ratified (Apr/2024) much later than its components zba/zbb/zbs
(Jun/2021). With "b" added into riscv/extensions.yaml, a dependency
checking rule is now enforced, which requires that when zba, zbb, and zbs
are all specified, "b" must be added as well. Failing to do this will
cause dtbs_check schema check warnings.
According to uabi.rst, as a single-letter extension, "b" should be added
after "c" in canonical order.
Update sg2044-cpus.dtsi to conform to this rule.
Signed-off-by: Guodong Xu <guodong@riscstar.com>
Reviewed-by: Inochi Amaoto <inochiama@gmail.com>
Link: https://lore.kernel.org/r/20260115-adding-b-dtsi-v2-3-254dd61cf947@riscstar.com
Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
Signed-off-by: Chen Wang <wangchen20@iscas.ac.cn>
In sg2042.dtsi, some peripheral device node does not follow the
address order. Reorder them in ascending order by address.
Reviewed-by: Chen Wang <unicorn_wang@outlook.com>
Link: https://lore.kernel.org/r/20260113023828.790136-2-inochiama@gmail.com
Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
Signed-off-by: Chen Wang <wangchen20@iscas.ac.cn>
As we have a separate CPU dtsi file, move the PLIC and CLINT
node to the CPU dtsi file. This will make the sg2042.dtsi focus
on peripheral devices, and make the CPU dtsi force CPU related
devices.
Reviewed-by: Chen Wang <unicorn_wang@outlook.com>
Link: https://lore.kernel.org/r/20260113023828.790136-1-inochiama@gmail.com
Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
Signed-off-by: Chen Wang <wangchen20@iscas.ac.cn>
Warning was found when compiling using loongarch64-gcc 12.3.1:
$ make CFLAGS_tree-log.o=-Wmaybe-uninitialized
In file included from fs/btrfs/ctree.h:21,
from fs/btrfs/tree-log.c:12:
fs/btrfs/accessors.h: In function 'replay_one_buffer':
fs/btrfs/accessors.h:66:16: warning: 'inode_item' may be used uninitialized [-Wmaybe-uninitialized]
66 | return btrfs_get_##bits(eb, s, offsetof(type, member)); \
| ^~~~~~~~~~
fs/btrfs/tree-log.c:2803:42: note: 'inode_item' declared here
2803 | struct btrfs_inode_item *inode_item;
| ^~~~~~~~~~
Initialize the inode_item to NULL, the compiler does not seem to see the
relation between the first 'wc->log_key.type == BTRFS_INODE_ITEM_KEY'
check and the other one that also checks the replay phase.
Signed-off-by: Qiang Ma <maqianga@uniontech.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Fast commits only log operations that have dedicated replay support.
EXT4_IOC_GROUP_EXTEND grows the filesystem to the end of the last
block group and updates the same on-disk metadata without going
through the fast commit tracking paths.
In practice these operations are rare and usually followed by further
updates, but mixing them into a fast commit makes the overall
semantics harder to reason about and risks replay gaps if new call
sites appear.
Teach ext4 to mark the filesystem fast-commit ineligible when
EXT4_IOC_GROUP_EXTEND grows the filesystem.
This forces those transactions to fall back to a full commit,
ensuring that the group extension changes are captured by the normal
journal rather than partially encoded in fast commit TLVs.
This change should not affect common workloads but makes online
resize via GROUP_EXTEND safer and easier to reason about under fast
commit.
Testing:
1. prepare:
dd if=/dev/zero of=/root/fc_resize.img bs=1M count=0 seek=256
mkfs.ext4 -O fast_commit -F /root/fc_resize.img
mkdir -p /mnt/fc_resize && mount -t ext4 -o loop /root/fc_resize.img /mnt/fc_resize
2. Extended the filesystem to the end of the last block group using a
helper that calls EXT4_IOC_GROUP_EXTEND on the mounted filesystem
and checked fc_info:
./group_extend_helper /mnt/fc_resize
cat /proc/fs/ext4/loop0/fc_info
shows the "Resize" ineligible reason increased.
3. Fsynced a file on the resized filesystem and confirmed that the fast
commit ineligible counter incremented for the resize transaction:
touch /mnt/fc_resize/file
/root/fsync_file /mnt/fc_resize/file
sync
cat /proc/fs/ext4/loop0/fc_info
Signed-off-by: Li Chen <me@linux.beauty>
Link: https://patch.msgid.link/20251211115146.897420-6-me@linux.beauty
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Fast commits only log operations that have dedicated replay support.
Online resize via EXT4_IOC_GROUP_ADD updates the superblock and group
descriptor metadata without going through the fast commit tracking
paths.
In practice these operations are rare and usually followed by further
updates, but mixing them into a fast commit makes the overall
semantics harder to reason about and risks replay gaps if new call
sites appear.
Teach ext4 to mark the filesystem fast-commit ineligible when
ext4_ioctl_group_add() adds new block groups.
This forces those transactions to fall back to a full commit,
ensuring that the filesystem geometry updates are captured by the
normal journal rather than partially encoded in fast commit TLVs.
This change should not affect common workloads but makes online
resize via GROUP_ADD safer and easier to reason about under fast
commit.
Testing:
1. prepare:
dd if=/dev/zero of=/root/fc_resize.img bs=1M count=0 seek=256
mkfs.ext4 -O fast_commit -F /root/fc_resize.img
mkdir -p /mnt/fc_resize && mount -t ext4 -o loop /root/fc_resize.img /mnt/fc_resize
2. Ran a helper that issues EXT4_IOC_GROUP_ADD on the mounted
filesystem and checked the resize ineligible reason:
./group_add_helper /mnt/fc_resize
cat /proc/fs/ext4/loop0/fc_info
shows "Resize": > 0.
3. Fsynced a file on the resized filesystem and verified that the fast
commit stats report at least one ineligible commit:
touch /mnt/fc_resize/file
/root/fsync_file /mnt/fc_resize/file
sync
cat /proc/fs/ext4/loop0/fc_info
shows fc stats ineligible > 0.
Signed-off-by: Li Chen <me@linux.beauty>
Link: https://patch.msgid.link/20251211115146.897420-5-me@linux.beauty
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Fast commits only log operations that have dedicated replay support.
EXT4_IOC_MOVE_EXT swaps extents between regular files and may copy
data, rewriting the affected inodes' block mapping layout without
going through the fast commit tracking paths.
In practice these operations are rare and usually followed by further
updates, but mixing them into a fast commit makes the overall
semantics harder to reason about and risks replay gaps if new call
sites appear.
Teach ext4 to mark the filesystem fast-commit ineligible for the
journal transactions used by move_extent_per_page() when
EXT4_IOC_MOVE_EXT runs.
This forces those transactions to fall back to a full commit,
ensuring that these multi-inode extent swaps are captured by the
normal journal rather than partially encoded in fast commit TLVs.
This change should not affect common workloads but makes online
defragmentation safer and easier to reason about under fast commit.
Testing:
1. prepare:
dd if=/dev/zero of=/root/fc_move.img bs=1M count=0 seek=256
mkfs.ext4 -O fast_commit -F /root/fc_move.img
mkdir -p /mnt/fc_move && mount -t ext4 -o loop \
/root/fc_move.img /mnt/fc_move
2. Created two files, ran EXT4_IOC_MOVE_EXT via e4defrag, and checked
the ineligible reason statistics:
fallocate -l 64M /mnt/fc_move/file1
cp /mnt/fc_move/file1 /mnt/fc_move/file2
e4defrag /mnt/fc_move/file1
cat /proc/fs/ext4/loop0/fc_info
shows "Move extents": > 0 and fc stats ineligible > 0.
Signed-off-by: Li Chen <me@linux.beauty>
Link: https://patch.msgid.link/20251211115146.897420-4-me@linux.beauty
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Fast commits only log operations that have dedicated replay support.
Enabling fs-verity builds a Merkle tree and updates inode and orphan
state in ways that are not described by the fast commit replay tags.
In practice these operations are rare and usually followed by further
updates, but mixing them into a fast commit makes the overall
semantics harder to reason about and risks replay gaps if new call
sites appear.
Teach ext4 to mark the filesystem fast-commit ineligible when
ext4_end_enable_verity() starts its journal transaction.
This forces that transaction to fall back to a full commit, ensuring
that the fs-verity enable changes are captured by the normal journal
rather than partially encoded in fast commit TLVs.
This change should not affect common workloads but makes fs-verity
enable safer and easier to reason about under fast commit.
Testing:
1. prepare:
dd if=/dev/zero of=/root/fc_verity.img bs=1M count=0 seek=128
mkfs.ext4 -O fast_commit,verity -F /root/fc_verity.img
mkdir -p /mnt/fc_verity && mount -t ext4 -o loop /root/fc_verity.img /mnt/fc_verity
2. Enabled fs-verity on a file and verified reason accounting:
echo "data" > /mnt/fc_verity/verityfile
/root/enable_verity /mnt/fc_verity/verityfile
sync
tail -n 1 /proc/fs/ext4/loop0/fc_info
"fs-verity enable": 1
3. Enabled fs-verity on a second file, fsynced it, and checked that the
ineligible commit counter is updated too:
echo "data2" > /mnt/fc_verity/verityfile2
/root/enable_verity /mnt/fc_verity/verityfile2
/root/fsync_file /mnt/fc_verity/verityfile2
sync
/proc/fs/ext4/loop0/fc_info shows "fs-verity enable" incremented and
fc stats ineligible increased accordingly.
Signed-off-by: Li Chen <me@linux.beauty>
Link: https://patch.msgid.link/20251211115146.897420-3-me@linux.beauty
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Fast commits only log operations that have dedicated replay support.
Inode format migration (indirect<->extent layout changes via
EXT4_IOC_MIGRATE or toggling EXT4_EXTENTS_FL) rewrites the block mapping
representation without going through the fast commit tracking paths.
In practice these migrations are rare and usually followed by further
updates, but mixing them into a fast commit makes the overall semantics
harder to reason about and risks replay gaps if new call sites appear.
Teach ext4 to mark the filesystem fast-commit ineligible when
ext4_ext_migrate() or ext4_ind_migrate() start their journal transactions.
This forces those transactions to fall back to a full commit, ensuring
that the entire inode layout change is captured by the normal journal
rather than partially encoded in fast commit TLVs. This change should
not affect common workloads but makes format migrations safer and easier
to reason about under fast commit.
Testing:
1. prepare:
dd if=/dev/zero of=/root/fc.img bs=1M count=0 seek=128
mkfs.ext4 -O fast_commit -F /root/fc.img
mkdir -p /mnt/fc && mount -t ext4 -o loop /root/fc.img /mnt/fc
2. Created a test file and toggled the extents flag to exercise both
ext4_ind_migrate() and ext4_ext_migrate():
touch /mnt/fc/migtest
chattr -e /mnt/fc/migtest
chattr +e /mnt/fc/migtest
3. Verified fast-commit ineligible statistics:
tail -n 1 /proc/fs/ext4/loop0/fc_info
"Inode format migration": 2
Signed-off-by: Li Chen <me@linux.beauty>
Link: https://patch.msgid.link/20251211115146.897420-2-me@linux.beauty
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Add a new sysfs attribute "err_report_sec" to control the s_err_report
timer in ext4_sb_info. Writing '0' disables the timer, while writing
a non-zero value enables the timer and sets the timeout in seconds.
Signed-off-by: Baolin Liu <liubaolin@kylinos.cn>
Link: https://patch.msgid.link/20251211030256.28613-1-liubaolin12138@163.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
When running `kvm-xfstests -c ext4/1k -C 1 generic/383` with the
`DOUBLE_CHECK` macro defined, the following panic is triggered:
==================================================================
EXT4-fs error (device vdc): ext4_validate_block_bitmap:423:
comm mount: bg 0: bad block bitmap checksum
BUG: unable to handle page fault for address: ff110000fa2cc000
PGD 3e01067 P4D 3e02067 PUD 0
Oops: Oops: 0000 [#1] SMP NOPTI
CPU: 0 UID: 0 PID: 2386 Comm: mount Tainted: G W
6.18.0-gba65a4e7120a-dirty #1152 PREEMPT(none)
RIP: 0010:percpu_counter_add_batch+0x13/0xa0
Call Trace:
<TASK>
ext4_mark_group_bitmap_corrupted+0xcb/0xe0
ext4_validate_block_bitmap+0x2a1/0x2f0
ext4_read_block_bitmap+0x33/0x50
mb_group_bb_bitmap_alloc+0x33/0x80
ext4_mb_add_groupinfo+0x190/0x250
ext4_mb_init_backend+0x87/0x290
ext4_mb_init+0x456/0x640
__ext4_fill_super+0x1072/0x1680
ext4_fill_super+0xd3/0x280
get_tree_bdev_flags+0x132/0x1d0
vfs_get_tree+0x29/0xd0
vfs_cmd_create+0x59/0xe0
__do_sys_fsconfig+0x4f6/0x6b0
do_syscall_64+0x50/0x1f0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
==================================================================
This issue can be reproduced using the following commands:
mkfs.ext4 -F -q -b 1024 /dev/sda 5G
tune2fs -O quota,project /dev/sda
mount /dev/sda /tmp/test
With DOUBLE_CHECK defined, mb_group_bb_bitmap_alloc() reads
and validates the block bitmap. When the validation fails,
ext4_mark_group_bitmap_corrupted() attempts to update
sbi->s_freeclusters_counter. However, this percpu_counter has not been
initialized yet at this point, which leads to the panic described above.
Fix this by moving the execution of ext4_percpu_param_init() to occur
before ext4_mb_init(), ensuring the per-CPU counters are initialized
before they are used.
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20251209133116.731350-1-libaokun@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Dual-voltage GPIO banks default to 3.3V operation. Even when a bank is
externally supplied with 1.8V, the internal logic remains in the 3.3V
domain, leading to functional failures.
Add support for programming the IO domain power control registers to
allow explicit configuration for 1.8V operation.
These registers are secure due to hardware safety constraints.
Specifically, configuring the domain for 1.8V while externally supplying
3.3V causes back-powering and potential pin damage. Consequently, access
requires unlocking the AIB Secure Access Register (ASAR) in the APBC
block before any read or write operation.
Signed-off-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
In order to access the protected IO power domain registers, a valid
unlock sequence must be performed by writing the required keys to the
AIB Secure Access Register (ASAR).
The ASAR register resides within the APBC register address space.
A corresponding syscon property is added to allow the pinctrl driver
to access this register.
Signed-off-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Both the hardware and driver already support polling mode. By removing
the mandatory IRQ requirement during probe, the driver can now fall
back to polling when an interrupt is unavailable, ensuring
compatibility with a wider range of systems.
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Link: https://patch.msgid.link/20260119-spi-xilinx-v3-2-4566c33bac0d@nexthop.ai
Signed-off-by: Mark Brown <broonie@kernel.org>
Both the hardware and driver already support polling mode. By removing
the mandatory IRQ requirement during probe, the driver can now fall
back to polling when an interrupt is unavailable, ensuring
compatibility with a wider range of systems.
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Link: https://patch.msgid.link/20260119-spi-xilinx-v3-1-4566c33bac0d@nexthop.ai
Signed-off-by: Mark Brown <broonie@kernel.org>
When switching to regmap, the i2c_client pointer was removed from struct
pcf8563 so this function switched to using the RTC device instead. But
the RTC device is a child of the original I2C device and does not have
an associated of_node.
Reference the correct device's of_node to ensure that the output clock
can be found when referenced by other devices and so that the override
clock name is read correctly.
Cc: stable@vger.kernel.org
Fixes: 00f1bb9b84 ("rtc: pcf8563: Switch to regmap")
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Link: https://patch.msgid.link/20260108184749.3413348-1-jkeeping@inmusicbrands.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
IS_REACHABLE() is meant to be used with full symbol names from a kernel
.config file, not the shortened symbols used in Kconfig files, so
change HWMON to CONFIG_HWMON in 3 places.
Fixes: dedaf03b99 ("rtc: max31335: add driver support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20260108045432.2705691-1-rdunlap@infradead.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The NV VRS RTC driver currently is only supported on the
Tegra platform so add a dep for ARCH_TEGRA and compile test
so it doesn't show up universally across all arches/platforms.
Fixes: 9d6d6b0693 ("rtc: nvvrs: add NVIDIA VRS RTC device driver")
Cc: Shubhi Garg <shgarg@nvidia.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20251222035651.433603-1-pbrobinson@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
strcpy() is deprecated [1] and using strcat() is discouraged. In
orangefs_debugfs_init() and orangefs_client_debug_init(), replace them
with memcpy() since the string lengths are already known. Replace all
other uses of strcpy() with the safer strscpy().
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strcpy [1]
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
strcpy() has been deprecated [1] because it performs no bounds checking
on the destination buffer, which can lead to buffer overflows. Replace
it with the safer strscpy(). No functional changes.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strcpy [1]
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
For native, the choice of PTE is fine. There's real memory backing the
non-present PTE. However, for XenPV, Xen complains:
(XEN) d1 L1TF-vulnerable L1e 8010000018200066 - Shadowing
To explain, some background on XenPV pagetables:
Xen PV guests are control their own pagetables; they choose the new
PTE value, and use hypercalls to make changes so Xen can audit for
safety.
In addition to a regular reference count, Xen also maintains a type
reference count. e.g. SegDesc (referenced by vGDT/vLDT), Writable
(referenced with _PAGE_RW) or L{1..4} (referenced by vCR3 or a lower
pagetable level). This is in order to prevent e.g. a page being
inserted into the pagetables for which the guest has a writable mapping.
For non-present mappings, all other bits become software accessible,
and typically contain metadata rather a real frame address. There is
nothing that a reference count could sensibly be tied to. As such, even
if Xen could recognise the address as currently safe, nothing would
prevent that frame from changing owner to another VM in the future.
When Xen detects a PV guest writing a L1TF-PTE, it responds by
activating shadow paging. This is normally only used for the live phase
of migration, and comes with a reasonable overhead.
KFENCE only cares about getting #PF to catch wild accesses; it doesn't
care about the value for non-present mappings. Use a fully inverted PTE,
to avoid hitting the slow path when running under Xen.
While adjusting the logic, take the opportunity to skip all actions if the
PTE is already in the right state, half the number PVOps callouts, and
skip TLB maintenance on a !P -> P transition which benefits non-Xen cases
too.
Link: https://lkml.kernel.org/r/20260106180426.710013-1-andrew.cooper3@citrix.com
Fixes: 1dc0da6e9e ("x86, kfence: enable KFENCE for x86")
Signed-off-by: Andrew Cooper <andrew.cooper3@citrix.com>
Tested-by: Marco Elver <elver@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Marco Elver <elver@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Jann Horn <jannh@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The current implementation of mmap() is set up such that a struct file
object is obtained for the input fd in ksys_mmap_pgoff() via fget(), and
its reference count decremented at the end of the function via. fput().
If a merge can be achieved, we are fine to simply decrement the refcount
on the file. Otherwise, in __mmap_new_file_vma(), we increment the
reference count on the file via get_file() such that the fput() in
ksys_mmap_pgoff() does not free the now-referenced file object.
The introduction of the f_op->mmap_prepare hook changes things, as it
becomes possible for a driver to replace the file object right at the
beginning of the mmap operation.
The current implementation is buggy if this happens because it
unconditionally calls get_file() on the mapping's file whether or not it
was replaced (and thus whether or not its reference count will be
decremented at the end of ksys_mmap_pgoff()).
This results in a memory leak, and was exposed in commit ab04945f91
("mm: update mem char driver to use mmap_prepare").
This patch solves the problem by explicitly tracking whether we actually
need to call get_file() on the file or not, and only doing so if required.
Link: https://lkml.kernel.org/r/20260112155143.661284-1-lorenzo.stoakes@oracle.com
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Fixes: ab04945f91 ("mm: update mem char driver to use mmap_prepare")
Reported-by: syzbot+bf5de69ebb4bdf86f59f@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/6964a92b.050a0220.eaf7.008a.GAE@google.com/
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Jann Horn <jannh@google.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Pedro Falcato <pfalcato@suse.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Syzbot has found a deadlock (analyzed by Lance Yang):
1) Task (5749): Holds folio_lock, then tries to acquire i_mmap_rwsem(read lock).
2) Task (5754): Holds i_mmap_rwsem(write lock), then tries to acquire
folio_lock.
migrate_pages()
-> migrate_hugetlbs()
-> unmap_and_move_huge_page() <- Takes folio_lock!
-> remove_migration_ptes()
-> __rmap_walk_file()
-> i_mmap_lock_read() <- Waits for i_mmap_rwsem(read lock)!
hugetlbfs_fallocate()
-> hugetlbfs_punch_hole() <- Takes i_mmap_rwsem(write lock)!
-> hugetlbfs_zero_partial_page()
-> filemap_lock_hugetlb_folio()
-> filemap_lock_folio()
-> __filemap_get_folio <- Waits for folio_lock!
The migration path is the one taking locks in the wrong order according to
the documentation at the top of mm/rmap.c. So expand the scope of the
existing i_mmap_lock to cover the calls to remove_migration_ptes() too.
This is (mostly) how it used to be after commit c0d0381ade. That was
removed by 336bf30eb7 for both file & anon hugetlb pages when it should
only have been removed for anon hugetlb pages.
Link: https://lkml.kernel.org/r/20260109041345.3863089-2-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Fixes: 336bf30eb7 ("hugetlbfs: fix anon huge page migration race")
Reported-by: syzbot+2d9c96466c978346b55f@syzkaller.appspotmail.com
Link: https://lore.kernel.org/all/68e9715a.050a0220.1186a4.000d.GAE@google.com
Debugged-by: Lance Yang <lance.yang@linux.dev>
Acked-by: David Hildenbrand (Red Hat) <david@kernel.org>
Acked-by: Zi Yan <ziy@nvidia.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Byungchul Park <byungchul@sk.com>
Cc: Gregory Price <gourry@gourry.net>
Cc: Jann Horn <jannh@google.com>
Cc: Joshua Hahn <joshua.hahnjy@gmail.com>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Rakie Kim <rakie.kim@sk.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Ying Huang <ying.huang@linux.alibaba.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The panic_print_deprecated() warning is being triggered on both read and
write operations to the panic_print parameter.
This causes spurious warnings when users run 'sysctl -a' to list all
sysctl values, since that command reads /proc/sys/kernel/panic_print and
triggers the deprecation notice.
Modify the handlers to only emit the deprecation warning when the
parameter is actually being set:
- sysctl_panic_print_handler(): check 'write' flag before warning.
- panic_print_get(): remove the deprecation call entirely.
This way, users are only warned when they actively try to use the
deprecated parameter, not when passively querying system state.
Link: https://lkml.kernel.org/r/20260106163321.83586-1-gal@nvidia.com
Fixes: ee13240cd7 ("panic: add note that panic_print sysctl interface is deprecated")
Fixes: 2683df6539 ("panic: add note that 'panic_print' parameter is deprecated")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Nimrod Oren <noren@nvidia.com>
Cc: Feng Tang <feng.tang@linux.alibaba.com>
Cc: Joel Granados <joel.granados@kernel.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Above the while() loop in wait_sb_inodes(), we document that we must wait
for all pages under writeback for data integrity. Consequently, if a
mapping, like fuse, traditionally does not have data integrity semantics,
there is no need to wait at all; we can simply skip these inodes.
This restores fuse back to prior behavior where syncs are no-ops. This
fixes a user regression where if a system is running a faulty fuse server
that does not reply to issued write requests, this causes wait_sb_inodes()
to wait forever.
Link: https://lkml.kernel.org/r/20260105211737.4105620-2-joannelkoong@gmail.com
Fixes: 0c58a97f91 ("fuse: remove tmp folio for writebacks and internal rb tree")
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Reported-by: Athul Krishna <athul.krishna.kr@protonmail.com>
Reported-by: J. Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Bernd Schubert <bschubert@ddn.com>
Tested-by: J. Neuschäfer <j.neuschaefer@gmx.net>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Bernd Schubert <bschubert@ddn.com>
Cc: Bonaccorso Salvatore <carnil@debian.org>
Cc: Christian Brauner <brauner@kernel.org>
Cc: David Hildenbrand <david@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: "Liam R. Howlett" <Liam.Howlett@oracle.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Both init_mm and efi_mm static definitions need to make room for the 2
mm_cid cpumasks.
This fixes possible out-of-bounds accesses to init_mm and efi_mm.
Add a space between # and define for the mm_alloc_cid() definition to make
it consistent with the coding style used in the rest of this header file.
Link: https://lkml.kernel.org/r/20251224173358.647691-4-mathieu.desnoyers@efficios.com
Fixes: af7f588d8f ("sched: Introduce per-memory-map concurrency ID")
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Reviewed-by: Thomas Gleixner <tglx@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Aboorva Devarajan <aboorvad@linux.ibm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Baolin Wang <baolin.wang@linux.alibaba.com>
Cc: Christan König <christian.koenig@amd.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: "Liam R . Howlett" <liam.howlett@oracle.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Martin Liu <liumartin@google.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mateusz Guzik <mjguzik@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: SeongJae Park <sj@kernel.org>
Cc: Shakeel Butt <shakeel.butt@linux.dev>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Sweet Tea Dorminy <sweettea-kernel@dorminy.me>
Cc: Tejun Heo <tj@kernel.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Wei Yang <richard.weiyang@gmail.com>
Cc: Yu Zhao <yuzhao@google.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The cpu_bitmap flexible array now contains more than just the cpu_bitmap.
In preparation for changing the static mm_struct definitions to cover for
the additional space required, change the cpu_bitmap type from "unsigned
long" to "char", require an unsigned long alignment of the flexible array,
and rename the field from "cpu_bitmap" to "flexible_array".
Introduce the MM_STRUCT_FLEXIBLE_ARRAY_INIT macro to statically initialize
the flexible array. This covers the init_mm and efi_mm static
definitions.
This is a preparation step for fixing the missing mm_cid size for static
mm_struct definitions.
Link: https://lkml.kernel.org/r/20251224173358.647691-3-mathieu.desnoyers@efficios.com
Fixes: af7f588d8f ("sched: Introduce per-memory-map concurrency ID")
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Reviewed-by: Thomas Gleixner <tglx@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Aboorva Devarajan <aboorvad@linux.ibm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Baolin Wang <baolin.wang@linux.alibaba.com>
Cc: Christan König <christian.koenig@amd.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: "Liam R . Howlett" <liam.howlett@oracle.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Martin Liu <liumartin@google.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mateusz Guzik <mjguzik@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: SeongJae Park <sj@kernel.org>
Cc: Shakeel Butt <shakeel.butt@linux.dev>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Sweet Tea Dorminy <sweettea-kernel@dorminy.me>
Cc: Tejun Heo <tj@kernel.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Wei Yang <richard.weiyang@gmail.com>
Cc: Yu Zhao <yuzhao@google.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
