commit c776cd89fc upstream.
The attached change significantly improves the performance of the LWS-CAS code
in syscall.S.
This allows a number of packages to build (e.g., zeromq3, gtest and libxs)
that previously failed because slow LWS-CAS performance under contention. In
particular, interrupts taken while the lock was taken degraded performance
significantly.
The change does the following:
1) Disables interrupts around the CAS operation, and
2) Changes the loads and stores to use the ordered completer, "o", on
PA 2.0. "o" and "ma" with a zero offset are equivalent. The latter is
accepted on both PA 1.X and 2.0.
The use of ordered loads and stores probably makes no difference on all
existing hardware, but it seemed pedantically correct. In particular, the CAS
operation must complete before LDCW lock is released. As written before, a
processor could reorder the operations.
I don't believe the period interrupts are disabled is long enough to
significantly increase interrupt latency. For example, the TLB insert code is
longer. Worst case is a memory fault in the CAS operation.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fef47e2a2e upstream.
Ratelimit printing of userspace segfaults and make it runtime
configurable via the /proc/sys/debug/exception-trace variable. This
should resolve syslog from growing way too fast and thus prevents
possible system service attacks.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44330ab516 upstream.
The register CLASS_D_CONTROL_1 is marked as volatile because it contains
a bit, DAC_MUTE, which is also mirrored in the ADC_DAC_CONTROL_1
register. This causes problems for the "Speaker Switch" control, which
will report an error if the CODEC is suspended because it relies on a
volatile register.
To resolve this issue mark CLASS_D_CONTROL_1 as non-volatile and
manually keep the register cache in sync by updating both bits when
changing the mute status.
Reported-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca5106ae3d upstream.
For CODEC to CODEC DAI links the paths are created in snd_soc_dapm_new_pcm().
Also for CODEC to CODEC links the widgets are connected cross-over via a DAI
link widget, meaning that the capture widget of one CODEC will be connected to
the playback widget of the other and vice versa. Whereas
snd_soc_dapm_connect_dai_link_widgets() directly connects the playback widget of
the CPU DAI to the playback widget of the CODEC DAI and the capture widget of
the CPU DAI to the capture widget of the CODEC DAI. So not skipping
CODEC<->CODEC links in snd_soc_dapm_connect_dai_link_widgets() will create
incorrect connections between the two CODECs which will cause DAPM to detect
active paths where there are none and unnecessarily power up widgets.
Fixes: b893ea5 ("ASoC: sapm: Automatically connect DAI link widgets in DAPM graph.")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83f7a85f11 upstream.
In case RFKILL is in KILL position, the NIC will issue an
interrupt straight away. This interrupt won't be sent
because it is masked in the hardware.
But if our interrupt service routine is called for another
reason (SHARED_IRQ), then we'll look at the interrupt cause
and service it. This can cause bad things if we are not
ready yet.
Explicitly clean the interrupt cause register to make sure
we won't service anything before we are ready to.
Reported-and-tested-by: Alexander Monakov <amonakov@gmail.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a838c3b60 upstream.
pcpu_chunk_struct_size = sizeof(struct pcpu_chunk) +
BITS_TO_LONGS(pcpu_unit_pages) * sizeof(unsigned long)
It hardly could be ever bigger than PAGE_SIZE even for large-scale machine,
but for consistency with its couterpart pcpu_mem_zalloc(),
use pcpu_mem_free() instead.
Commit b4916cb17c ("percpu: make pcpu_free_chunk() use
pcpu_mem_free() instead of kfree()") addressed this problem, but
missed this one.
tj: commit message updated
Signed-off-by: Jianyu Zhan <nasa4836@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 099a19d91c ("percpu: allow limited allocation before slab is online)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b25bcf1bca upstream.
Since the mvebu-soc-id code in mach-mvebu/ was introduced, several
users have noticed a regression: the PCIe card connected in the first
PCIe interface is not detected properly.
This is due to the fact that the mvebu-soc-id code enables the PCIe
clock of the first PCIe interface, reads the SoC device ID and
revision number (yes this information is made available as part of
PCIe registers), and then disables the clock. However, by doing this,
we gate the clock and therefore loose the complex PCIe configuration
that was done by the bootloader.
Unfortunately, as of today, the kernel is not capable of doing this
complex configuration by itself, so we really need to keep the PCIe
clock enabled. However, we don't want to keep it enabled
unconditionally: if the PCIe interface is not enabled or PCI support
is not compiled into the kernel, there is no reason to keep the PCIe
clock running.
This issue was discussed with Kevin Hilman, and the suggested solution
was to make the mvebu-soc-id code keep the clock enabled in case it
will be needed for PCIe. This is therefore the solution implemented in
this patch.
Long term, we hope to make the kernel more capable in terms of PCIe
configuration for this platform, which will anyway be needed to
support the compilation of the PCIe host controller driver as a
module. In the mean time however, we don't have much other choice than
to implement the currently proposed solution.
Reported-by: Neil Greatorex <neil@fatboyfat.co.uk>
Cc: Neil Greatorex <neil@fatboyfat.co.uk>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1399903900-29977-3-git-send-email-thomas.petazzoni@free-electrons.com
Fixes: af8d1c63af ("ARM: mvebu: Add support to get the ID and the revision of a SoC")
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42a18d1cf4 upstream.
The mvebu-soc-id code in mach-mvebu/ needs to enable a clock to read
the SoC device ID and revision number. To do so, it does a clk_get(),
then a clk_prepare_enable(), reads the value, and disables the clock
with clk_disable_unprepare(). However, it forgets to clk_put() the
clock. This commit fixes this issue.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1399903900-29977-2-git-send-email-thomas.petazzoni@free-electrons.com
Fixes: af8d1c63af ("ARM: mvebu: Add support to get the ID and the revision of a SoC")
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 398f5d5e10 upstream.
MBus windows are used on Marvell platforms to map certain peripherals
in the physical address space. In the PCIe context, MBus windows are
needed to map PCIe I/O and memory regions in the physical address.
However, those MBus windows can only have power of two sizes, while
PCIe BAR do not necessarily guarantee this. For this reason, the
current pci-mvebu breaks on platforms where PCIe devices have BARs
that don't sum up to a power of two size at the emulated bridge level.
This commit fixes this by allowing the pci-mvebu driver to create
multiple contiguous MBus windows (each having a power of two size) to
cover a given PCIe BAR.
To achieve this, two functions are added: mvebu_pcie_add_windows() and
mvebu_pcie_del_windows() to respectively add and remove all the MBus
windows that are needed to map the provided PCIe region base and
size. The emulated PCI bridge code now calls those functions, instead
of directly calling the mvebu-mbus driver functions.
Fixes: 45361a4fe4 ('pci: PCIe driver for Marvell Armada 370/XP systems')
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1397823593-1932-8-git-send-email-thomas.petazzoni@free-electrons.com
Tested-by: Neil Greatorex <neil@fatboyfat.co.uk>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b566e782be upstream.
Having multiple windows with the same target and attribute is actually
legal, and can be useful for PCIe windows, when PCIe BARs have a size
that isn't a power of two, and we therefore need to create several
MBus windows to cover the PCIe BAR for a given PCIe interface.
Fixes: fddddb52a6 ('bus: introduce an Marvell EBU MBus driver')
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1397823593-1932-7-git-send-email-thomas.petazzoni@free-electrons.com
Tested-by: Neil Greatorex <neil@fatboyfat.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6d07e0273 upstream.
mvebu_pcie_handle_membase_change() and
mvebu_pcie_handle_iobase_change() do not correctly compute the window
size. PCI uses an inclusive start/end address pair, which requires a
+1 when converting to size.
This only worked because a bug in the mbus driver allowed it to
silently accept and round up bogus sizes.
Fix this by adding one to the computed size.
Fixes: 45361a4fe4 ('PCIe driver for Marvell Armada 370/XP systems')
Signed-off-by: Willy Tarreau <w@1wt.eu>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1397823593-1932-5-git-send-email-thomas.petazzoni@free-electrons.com
Tested-by: Neil Greatorex <neil@fatboyfat.co.uk>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce965c3d2e upstream.
According to the Armada 370 and Armada XP datasheets, the part of the
Device Bus register that configure the bus width should contain 0 for
a 8 bits bus width, and 1 for a 16 bits bus width (other values are
unsupported/reserved).
However, the current conversion done in the driver to convert from a
bus width in bits to the value expected by the register leads to
setting the register to 1 for a 8 bits bus, and 2 for a 16 bits bus.
This mistake was compensated by a mistake in the existing Device Tree
files for Armada 370/XP platforms: they were declaring a 8 bits bus
width, while the hardware in fact uses a 16 bits bus width.
This commit fixes that by adjusting the conversion logic.
This patch fixes a bug that was introduced in
3edad321b1 ('drivers: memory: Introduce
Marvell EBU Device Bus driver'), which was merged in v3.11.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1397489361-5833-2-git-send-email-thomas.petazzoni@free-electrons.com
Fixes: 3edad321b1 ('drivers: memory: Introduce Marvell EBU Device Bus driver')
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d595b866d upstream.
After a @pwq is scheduled for emergency execution, other workers may
consume the affectd work items before the rescuer gets to them. This
means that a workqueue many have pwqs queued on @wq->maydays list
while not having any work item pending or in-flight. If
destroy_workqueue() executes in such condition, the rescuer may exit
without emptying @wq->maydays.
This currently doesn't cause any actual harm. destroy_workqueue() can
safely destroy all the involved data structures whether @wq->maydays
is populated or not as nobody access the list once the rescuer exits.
However, this is nasty and makes future development difficult. Let's
update rescuer_thread() so that it empties @wq->maydays after seeing
should_stop to guarantee that the list is empty on rescuer exit.
tj: Updated comment and patch description.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77668c8b55 upstream.
There is a race condition between rescuer_thread() and
pwq_unbound_release_workfn().
Even after a pwq is scheduled for rescue, the associated work items
may be consumed by any worker. If all of them are consumed before the
rescuer gets to them and the pwq's base ref was put due to attribute
change, the pwq may be released while still being linked on
@wq->maydays list making the rescuer dereference already freed pwq
later.
Make send_mayday() pin the target pwq until the rescuer is done with
it.
tj: Updated comment and patch description.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77f300b198 upstream.
wq_update_unbound_numa() failure path has the following two bugs.
- alloc_unbound_pwq() is called without holding wq->mutex; however, if
the allocation fails, it jumps to out_unlock which tries to unlock
wq->mutex.
- The function should switch to dfl_pwq on failure but didn't do so
after alloc_unbound_pwq() failure.
Fix it by regrabbing wq->mutex and jumping to use_dfl_pwq on
alloc_unbound_pwq() failure.
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Acked-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 4c16bd327c ("workqueue: implement NUMA affinity for unbound workqueues")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1b8ff4c97 upstream.
The nfsv4 state code has always assumed a one-to-one correspondance
between lock stateid's and lockowners even if it appears not to in some
places.
We may actually change that, but for now when FREE_STATEID releases a
lock stateid it also needs to release the parent lockowner.
Symptoms were a subsequent LOCK crashing in find_lockowner_str when it
calls same_lockowner_ino on a lockowner that unexpectedly has an empty
so_stateids list.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27b11428b7 upstream.
The current code assumes a one-to-one lockowner<->lock stateid
correspondance.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4cb57e3032 upstream.
Mainly to ensure that we don't leave any hanging timers.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5694c93e6c upstream.
Aside from making it clearer what is non-trivial in create_client(), it
also fixes a bug whereby we can call free_client() before idr_init()
has been called.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77f07800cb upstream.
The recent Intel H97/Z97 chipsets need the similar setups like other
Intel chipsets for snooping, etc. Especially without snooping, the
audio playback stutters or gets corrupted. This fix patch just adds
the corresponding PCI ID entry with the proper flags.
Reported-and-tested-by: Arthur Borsboom <arthurborsboom@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f06ab794af upstream.
Since commit 1df5a06a ("ALSA: hda - hdmi: Fix programmed active channel
count") channel count is no longer being set if monitor_present is 0.
This is because setting the count was moved after the CA value is
determined, which is only after the monitor_present check in
hdmi_setup_audio_infoframe().
Unfortunately, in some cases, such as with a non-spec-compliant codec or
with a problematic video driver, monitor_present is always 0. As a
specific example, this seems to happen with gen1 ATV (SiI1390 codec),
causing left-channel-only stereo playback (multi-channel playback has
apparently never worked with this codec despite it reporting 8 channels,
reason unknown).
Simply setting converter channel count without setting the pin infoframe
and channel mapping as well does not theoretically make much sense as
this will just mean they are out-of-sync and multichannel playback will
have a wrong channel mapping.
However, adding back just setting the converter channel count even in
no-monitor case is the safest change which at least fixes the stereo
playback regression on SiI1390 codec. Do that.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Reported-by: Stephan Raue <stephan@openelec.tv>
Tested-by: Stephan Raue <stephan@openelec.tv>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f68f39c39 upstream.
Most of the affected models share pnp-ids for the touchpad. So switching
to pnp-ids give us 2 advantages:
1) It shrinks the quirk list
2) It will lower the new quirk addition frequency, ie the recently added W540
quirk would not have been necessary since it uses the same LEN0034 pnp ids
as other models already added before it
As an added bonus it actually puts the quirk on the actual psmouse, rather
then on the machine, which is technically more correct.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2f611029b upstream.
This is a preparation patch for simplifying the min/max quirk table.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d396ede22 upstream.
The T540p has a touchpad with pnp-id LEN0034, all the models with this
pnp-id have the same min/max values, except the T540p where the values are
slightly off. Fix them to be identical.
This is a preparation patch for simplifying the quirk table.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36189cc3cd upstream.
The hw_version 3 Elantech touchpad on the Gigabyte U2442 does not accept
0x0b as initialization value for r10, this stand-alone version of the
driver: http://planet76.com/drivers/elantech/psmouse-elantech-v6.tar.bz2
Uses 0x03 which does work, so this means not setting bit 3 of r10 which
sets: "Enable Real H/W Resolution In Absolute mode"
Which will result in half the x and y resolution we get with that bit set,
so simply not setting it everywhere is not a solution. We've been unable to
find a way to identify touchpads where setting the bit will fail, so this
patch uses a dmi based blacklist for this.
https://bugzilla.kernel.org/show_bug.cgi?id=61151
Reported-by: Philipp Wolfer <ph.wolfer@gmail.com>
Tested-by: Philipp Wolfer <ph.wolfer@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d725caa9d upstream.
After issuing ATKBD_CMD_RESET_DIS, keyboard on some LG laptops stops
working. The workaround is to stop issuing ATKBD_CMD_RESET_DIS commands.
In order to keep changes in atkbd driver to the minimum we check DMI
signature and only skip ATKBD_CMD_RESET_DIS if we are running on LG
LW25-B7HV or P1-J273B.
Signed-off-by: Sheng-Liang Song <ssl@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 098507ae3e upstream.
The replacement of the 'count' variable by two variables 'incs' and
'decs' to resolve some race conditions during module unloading was done
in parallel with some cleanup in the trace subsystem, and was integrated
as a merge.
Unfortunately, the formula for this replacement was wrong in the tracing
code, and the refcount in the traces was not usable as a result.
Use 'count = incs - decs' to compute the user count.
Link: http://lkml.kernel.org/p/1393924179-9147-1-git-send-email-romain.izard.pro@gmail.com
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Fixes: c1ab9cab75 "merge conflict resolution"
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22213318af upstream.
in non-lazy walk we need to be careful about dentry switching from
negative to positive - both ->d_flags and ->d_inode are updated,
and in some places we might see only one store. The cases where
dentry has been obtained by dcache lookup with ->i_mutex held on
parent are safe - ->d_lock and ->i_mutex provide all the barriers
we need. However, there are several places where we run into
trouble:
* do_last() fetches ->d_inode, then checks ->d_flags and
assumes that inode won't be NULL unless d_is_negative() is true.
Race with e.g. creat() - we might have fetched the old value of
->d_inode (still NULL) and new value of ->d_flags (already not
DCACHE_MISS_TYPE). Lin Ming has observed and reported the resulting
oops.
* a bunch of places checks ->d_inode for being non-NULL,
then checks ->d_flags for "is it a symlink". Race with symlink(2)
in case if our CPU sees ->d_inode update first - we see non-NULL
there, but ->d_flags still contains DCACHE_MISS_TYPE instead of
DCACHE_SYMLINK_TYPE. Result: false negative on "should we follow
link here?", with subsequent unpleasantness.
Reported-and-tested-by: Lin Ming <minggr@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b6751f7fe upstream.
autofs needs to be able to see private data dentry flags for its dentrys
that are being created but not yet hashed and for its dentrys that have
been rmdir()ed but not yet freed. It needs to do this so it can block
processes in these states until a status has been returned to indicate
the given operation is complete.
It does this by keeping two lists, active and expring, of dentrys in
this state and uses ->d_release() to keep them stable while it checks
the reference count to determine if they should be used.
But with the recent lockref changes dentrys being freed sometimes don't
transition to a reference count of 0 before being freed so autofs can
occassionally use a dentry that is invalid which can lead to a panic.
Signed-off-by: Ian Kent <raven@themaw.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a8a70f96f upstream.
When creating a file, ceph_set_dentry_offset() puts the new dentry
at the end of directory's d_subdirs, then set the dentry's offset
based on directory's max offset. The offset does not reflect the
real postion of the dentry in directory. Later readdir reply from
MDS may change the dentry's position/offset. This inconsistency
can cause missing/duplicate entries in readdir result if readdir
is partly satisfied by dcache_readdir().
The fix is clear directory's completeness after creating/renaming
file. It prevents later readdir from using dcache_readdir().
Fixes: http://tracker.ceph.com/issues/8025
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b20a774495 upstream.
In commit da1e2046e5, the flow for enabling/disabling an Si errata
workaround (e1000_lv_jumbo_workaround_ich8lan) was changed to fix a problem
with iAMT connections dropping on interface down with jumbo frames set.
Part of this change was to move the function call disabling the workaround
to e1000e_down() from the e1000_setup_rctl() function. The mechanic for
disabling of this workaround involves writing several MAC and PHY registers
back to hardware defaults.
After this commit, when the driver is loaded with the cable out, the PHY
registers are not programmed with the correct default values. This causes
the device to be capable of transmitting packets, but is unable to recieve
them until this workaround is called.
The flow of e1000e's open code relies upon calling the above workaround to
expicitly program these registers either with jumbo frame appropriate settings
or h/w defaults on 82579 and newer hardware.
Fix this issue by adding logic to e1000_setup_rctl() that not only calls
e1000_lv_jumbo_workaround_ich8lan() when jumbo frames are set, to enable the
workaround, but also calls this function to explicitly disable the workaround
in the case that jumbo frames are not set.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43e19888b1 upstream.
Check PNP ID of the PS/2 AUX port and report INPUT_PROP_TOPBUTTONPAD
property for for touchpads with top button areas.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f37c013409 upstream.
On some newer laptops with a trackpoint the physical buttons for the
trackpoint have been removed to allow for a larger touchpad. On these
laptops the buttonpad has clearly marked areas on the top which are to be
used as trackpad buttons.
Users of the event device-node need to know about this, so that they can
properly interpret BTN_LEFT events as being a left / right / middle click
depending on where on the button pad the clicking finger is.
This commits adds a INPUT_PROP_TOPBUTTONPAD device property which drivers
for such buttonpads will use to signal to the user that this buttonpad not
only has the normal bottom button area, but also a top button area.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7c5868c34 upstream.
Fill in the new serio firmware_id sysfs attribute for pnp instantiated
8042 serio ports.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0456c66f4e upstream.
serio devices exposed via platform firmware interfaces such as ACPI may
provide additional identifying information of use to userspace.
We don't associate the serio devices with the firmware device (we don't
set it as parent), so there's no way for userspace to make use of this
information.
We cannot change the parent for serio devices instantiated though a
firmware interface as that would break suspend / resume ordering.
Therefore this patch adds a new firmware_id sysfs attribute so that
userspace can get a string from there with any additional identifying
information the firmware interface may provide.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b4ed8b00e upstream.
If the allocation fails then we dereference the NULL in the error path.
Just return directly.
Fixes: ed27ff1db8 ('clk: Versatile Express clock generators ("osc") driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 130fa5bc81 upstream.
The crypto algorithm modules utilizing the crypto daemon could
be used early when the system start up. Using module_init
does not guarantee that the daemon's work queue is initialized
when the cypto alorithm depending on crypto_wq starts. It is necessary
to initialize the crypto work queue earlier at the subsystem
init time to make sure that it is initialized
when used.
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2c2b11cfa upstream.
[PATCH v3 1/2] device_cgroup: check if exception removal is allowed
When the device cgroup hierarchy was introduced in
bd2953ebbb - devcg: propagate local changes down the hierarchy
a specific case was overlooked. Consider the hierarchy bellow:
A default policy: ALLOW, exceptions will deny access
\
B default policy: ALLOW, exceptions will deny access
There's no need to verify when an new exception is added to B because
in this case exceptions will deny access to further devices, which is
always fine. Hierarchy in device cgroup only makes sure B won't have
more access than A.
But when an exception is removed (by writing devices.allow), it isn't
checked if the user is in fact removing an inherited exception from A,
thus giving more access to B.
Example:
# echo 'a' >A/devices.allow
# echo 'c 1:3 rw' >A/devices.deny
# echo $$ >A/B/tasks
# echo >/dev/null
-bash: /dev/null: Operation not permitted
# echo 'c 1:3 w' >A/B/devices.allow
# echo >/dev/null
#
This shouldn't be allowed and this patch fixes it by making sure to never allow
exceptions in this case to be removed if the exception is partially or fully
present on the parent.
v3: missing '*' in function description
v2: improved log message and formatting fixes
Cc: cgroups@vger.kernel.org
Cc: Li Zefan <lizefan@huawei.com>
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79d719749d upstream.
Whenever a device file is opened and checked against current device
cgroup rules, it uses the same function (may_access()) as when a new
exception rule is added by writing devices.{allow,deny}. And in both
cases, the algorithm is the same, doesn't matter the behavior.
First problem is having device access to be considered the same as rule
checking. Consider the following structure:
A (default behavior: allow, exceptions disallow access)
\
B (default behavior: allow, exceptions disallow access)
A new exception is added to B by writing devices.deny:
c 12:34 rw
When checking if that exception is allowed in may_access():
if (dev_cgroup->behavior == DEVCG_DEFAULT_ALLOW) {
if (behavior == DEVCG_DEFAULT_ALLOW) {
/* the exception will deny access to certain devices */
return true;
Which is ok, since B is not getting more privileges than A, it doesn't
matter and the rule is accepted
Now, consider it's a device file open check and the process belongs to
cgroup B. The access will be generated as:
behavior: allow
exception: c 12:34 rw
The very same chunk of code will allow it, even if there's an explicit
exception telling to do otherwise.
A simple test case:
# mkdir new_group
# cd new_group
# echo $$ >tasks
# echo "c 1:3 w" >devices.deny
# echo >/dev/null
# echo $?
0
This is a serious bug and was introduced on
c39a2a3018 devcg: prepare may_access() for hierarchy support
To solve this problem, the device file open function was split from the
new exception check.
Second problem is how exceptions are processed by may_access(). The
first part of the said function tries to match fully with an existing
exception:
list_for_each_entry_rcu(ex, &dev_cgroup->exceptions, list) {
if ((refex->type & DEV_BLOCK) && !(ex->type & DEV_BLOCK))
continue;
if ((refex->type & DEV_CHAR) && !(ex->type & DEV_CHAR))
continue;
if (ex->major != ~0 && ex->major != refex->major)
continue;
if (ex->minor != ~0 && ex->minor != refex->minor)
continue;
if (refex->access & (~ex->access))
continue;
match = true;
break;
}
That means the new exception should be contained into an existing one to
be considered a match:
New exception Existing match? notes
b 12:34 rwm b 12:34 rwm yes
b 12:34 r b *:34 rw yes
b 12:34 rw b 12:34 w no extra "r"
b *:34 rw b 12:34 rw no too broad "*"
b *:34 rw b *:34 rwm yes
Which is fine in some cases. Consider:
A (default behavior: deny, exceptions allow access)
\
B (default behavior: deny, exceptions allow access)
In this case the full match makes sense, the new exception cannot add
more access than the parent allows
But this doesn't always work, consider:
A (default behavior: allow, exceptions disallow access)
\
B (default behavior: deny, exceptions allow access)
In this case, a new exception in B shouldn't match any of the exceptions
in A, after all you can't allow something that was forbidden by A. But
consider this scenario:
New exception Existing in A match? outcome
b 12:34 rw b 12:34 r no exception is accepted
Because the new exception has "w" as extra, it doesn't match, so it'll
be added to B's exception list.
The same problem can happen during a file access check. Consider a
cgroup with allow as default behavior:
Access Exception match?
b 12:34 rw b 12:34 r no
In this case, the access didn't match any of the exceptions in the
cgroup, which is required since exceptions will disallow access.
To solve this problem, two new functions were created to match an
exception either fully or partially. In the example above, a partial
check will be performed and it'll produce a match since at least
"b 12:34 r" from "b 12:34 rw" access matches.
Cc: cgroups@vger.kernel.org
Cc: Tejun Heo <tj@kernel.org>
Cc: Serge Hallyn <serge.hallyn@canonical.com>
Cc: Li Zefan <lizefan@huawei.com>
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98b0f811aa upstream.
The English and Korean translations were updated, the Chinese and Japanese
weren't.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8fc1e8c240 upstream.
When brcm80211 firmware is not installed networking hangs.
A deadlock happens because we call ieee80211_unregister_hw()
from the .start callback of struct ieee80211_ops. When .start
is called we are under rtnl lock and ieee80211_unregister_hw()
tries to take it again.
Function call stack:
dev_change_flags()
__dev_change_flags()
__dev_open()
ASSERT_RTNL() <-- Assert rtnl lock
ops->ndo_open()
.ndo_open = ieee80211_open,
ieee80211_open()
ieee80211_do_open()
drv_start()
local->ops->start()
.start = brcms_ops_start,
brcms_ops_start()
brcms_remove()
ieee80211_unregister_hw()
rtnl_lock() <-- Here we deadlock
Introduced by:
commit 25b5632fb3
("brcmsmac: request firmware in .start() callback")
This patch fixes the bug by removing the call to brcms_remove()
and moves the brcms_request_fw() call to the top of the .start
callback to not initiate anything unless firmware is installed.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 392369019e upstream.
When probing with DT, we add each LED one at a time. If we find a LED
without a PWM device (because it is not available yet) we fail the
initialisation, unregister previous LEDs, and then by way of managed
resources, we free the structure.
The problem with this is we may have a scheduled and active work_struct
in this structure, and this results in a nasty kernel oops.
We need to cancel this work_struct properly upon cleanup - and the
cleanup we require is the same cleanup as we do when the LED platform
device is removed. Rather than writing this same code three times,
move it into a separate function and use it in all three places.
Fixes: c971ff185f ("leds: leds-pwm: Defer led_pwm_set() if PWM can sleep")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61679fe153 upstream.
This should fix a deadlock that has been reported to us where fan_update()
would hold the fan lock and try to grab the alarm_program_lock to reschedule
an update. On an other CPU, the alarm_program_lock would have been taken
before calling fan_update(), leading to a deadlock.
We should Cc: <stable@vger.kernel.org> # 3.9+
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Tested-by: Timothée Ravier <tim@siosm.fr>
Tested-by: Boris Fersing (IRC nick fersingb, no public email address)
Signed-off-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb06d10232 upstream.
When igb_set_interrupt_capability() calls
igb_reset_interrupt_capability() (e.g., because CONFIG_PCI_MSI is unset),
num_q_vectors has been set but no vector has yet been allocated.
igb_reset_interrupt_capability() will then call igb_reset_q_vector,
which assumes that the vector is allocated. As this is not the case, we
are accessing a NULL-pointer.
This patch fixes it by checking that q_vector is indeed different from
NULL.
Fixes: 02ef6e1d0b (igb: Fix queue allocation method to accommodate changing during runtime)
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
