Rework atomic.h to make the low level functions avaible for use
in other headers without using atomic_t, e.g. in bitops.h.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Commit a076d41823 ("ASoC: samsung: Drop AC97 drivers") removed some
unused code and the associated Kconfig options, but left those options
referenced in the Makefile. Remove the leftover references in the
Makefile.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to have a proper topology of regulators for a platform, each
registering regulator needs to populate supply_name field for identifying
its supply's name. Add supply_name field for lp873x regulators.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver fine-tune some parameters to improve FLL performance.
Those items have description as follow.
(1)ICTRL_LATCH: FLL DSP speed capability control
When FLL running at high frequency with long decimal number, DSP needs
to operate at high speed. FLL DSP can optimize between performance and
power consumption by ICTRL_LATCH.(111 has highest power consumption.)
The default setting can be used to reduce power.
(2)CUTOFF500: loop filter cutoff frequency at 500Khz
It will give the best FLL performance but highest power consumption
to enable the cutoff frequency. FLL Loop Filter enable to reduce FLL
output noise, especially,(DCO frequency)/(FLL input reference frequency)
is not a integer.
(3)GAIN_ERR: FLL gain error correction threshold setting
The threshold is comparison between DCO and target frequency.
The value 1111 has the most sensitive threshold, that is, 1111 can have
the most accurate DCO to target frequency. However, the gain error setting
conditionally and inversely depends on FLL input reference clock rate.
Higher FLL reference input frequency can only set lower gain error, such
as 0000 for input reference from MCLK=12.288Mhz. On the other side, if FLL
reference input is from Frame Sync, 48KHz, higher error gain can apply
such as 1111.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Over Sampling Rate (OSR) is defined as CLK_ADC frequency divided by the
audio sample rate (Fs).
OSR = CLK_ADC / FS
The available OSRs are 32, 64, 128 or 256. Note that the OSR and Fs
values must be selected such that the maximum frequency of CLK_ADC
is less than 6.144 MHz. It is recommended to match the relationship
between OSR and clock SRC according to following Table.
ADC_RATE: 00(OSR=32) | CLK_ADC_SRC: 11(CODEC 1/8)
ADC_RATE: 01(OSR=64) | CLK_ADC_SRC: 10(CODEC1/4)
ADC_RATE: 10(OSR=128) | CLK_ADC_SRC: 01(CODEC 1/2)
ADC_RATE: 11(OSR=256) | CLK_ADC_SRC: 00(CODEC CLK)
The over sampling rate about DAC follows the same rule with ADCs.
The driver changes the OSR to 64 value when initiation for better FLL
performance and applies the dynamic SRC change by different OSR.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the short Frame Sync detection logic enabled, the logic will check the
short frame sync threshold. If frame sync is less than the setting;
for example, frame sync less than 252 MCLK, the short frame sync signal is
flagged, digital filter temporary mute and skip that data.
If the system was intended for sampling rate change which could create
temporary short frame sync and not enough MIPS to run the digital filter.
But the situation doesn't happen in ALSA architecure. Thus the Frame Sync
is always stable, then no require to do the detection. Therefore,
the dirver disables the function for better performance.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The maximum supported voltage for ldo_io# is 3.3V, but on cold boot
the selector comes up at 0x1f, which maps to 3.8V. This was previously
corrected by Allwinner's U-boot, which set all regulators on the PMICs
to some pre-configured voltage. With recent progress in U-boot SPL
support, this is no longer the case. In any case we should handle
this quirk in the kernel driver as well.
This invalid setting causes _regulator_get_voltage() to fail with -EINVAL
which causes regulator registration to fail when constrains are used:
[ 1.054181] vcc-pg: failed to get the current voltage(-22)
[ 1.059670] axp20x-regulator axp20x-regulator.0: Failed to register ldo_io0
[ 1.069749] axp20x-regulator: probe of axp20x-regulator.0 failed with error -22
This commits makes the axp20x regulator driver accept the 0x1f register
value, fixing this.
The datasheet does not guarantee reliable operation above 3.3V, so on
boards where this regulator is used the regulator-max-microvolt setting
must be 3.3V or less.
This is essentially the same as the commit f40d4896bf ("regulator:
axp20x: Fix axp22x ldo_io registration error on cold boot") for AXP22x
PMICs.
Fixes: a51f9f4622 ("regulator: axp20x: support AXP809 variant")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is assuming that the card related information is located on
"card" node, but graph case doesn't have it.
This patch adds node parameter to adjust for graph support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is assuming that the card related information is located on
"card" node, but graph case doesn't have it.
This patch adds node parameter to adjust for graph support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Port the GMC v6 driver over to the new SI headers.
Tested with a Tahiti SI ASIC.
(v2) Fixed a couple of typos (in commented code) and moved
defines to si_enums.h
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This only has the effect of scanning the invisible range twice
since the topdown flag is given anyway.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: JimQu <Jim.Qu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This disables the VRAM manager when a special placement is requested, otherwise
we play ping/pong with the buffers on every command submission.
v2: only check lpfn
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: JimQu <Jim.Qu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. fix uvd cg status not correct.
2. fix uvd pg can't work on tonga.
3. enable uvd mgcg.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Tom St Denis <tom.stdenis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
when uvd is idle, we gate uvd clock.
and uvd is busy, we ungate uvd clock.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for the debugfs wave reader.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This changes the gfx v6 driver to use the new AMDGPU style
SI headers. Also fixes a variety of coding style issues, white
space issues, and uses WREG32_FIELD in a few places where
appropriate.
Tested with a Tahiti 0x679A.
v2: Squash in typo fix patch
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add missing gca MMIO registers and defines necessary for the
next patch which re-works a lot of gfx v6 to use the new SI
headers.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This introduces the SI registers in the amdgpu
driver style.
v2: squash duplicates fix
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Replace direct comparisons to NULL i.e.
'x == NULL' with '!x'. As per coding standard.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Ravikant B Sharma <ravikant.s2@samsung.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
De-numberify indirect register access for gfx v8.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
De-numberify indirect register access for gfx v7.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is used for virtualization support. In virtualization case,
Tonga SMC should not be started and SMU firmware should not be loaded
if in SRIOV environment. The same operation will be applied on FIJI in
other patch.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Signed-off-by: Trigger Huang <trigger.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. partial revert commit 91db308d6e96.
not set uvd bypass mode.
2. enable uvd cg before initialize uvd.
3. set uvd clock to default value 100MHz.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Voltage Controller have been enabled (SMC message)
before ULV enablement.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is used for virtualization support. In virtualization case,
the initialization sequences are not totally the same as
non-Virtualization's. The avfs event manager should be bypassed if in
SRIOV virtualization case. At the same, this patch will also bypass
starting SMC within SRIOV in FIJI, so the SMU firmware loading will be
avoid, which is required in SRIOV.
Signed-off-by: Frank Min <Frank.Min@amd.com>
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Trigger Huang <trigger.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
KIQ is used for interaction between driver and
CP, and not exposed to outside client, as such it
doesn't need to be handled by GPU scheduler.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Trigger Huang <trigger.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a new ring type definition for KIQ. KIQ is used for interaction
between driver and CP.
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Trigger Huang <trigger.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UVD clocks are set to be disabled, when not in use.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Tom StDenis <Tom.StDenis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Only for cards that are supported by powerplay.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Powerplay hwmgr already has an implementation, all we need to do is to call it.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In fence waiting, it never return -EDEADLK yet, so drop this function
here.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
use same module parameter with powercontainment
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
External clients which import our bo's wait only
for exclusive dmabuf-fences, not on shared ones,
ditto for bo's which we import from external
providers and write to.
Therefore attach exclusive fences on prime shared buffers
if our exported buffer gets imported by an external
client, or if we import a buffer from an external
exporter.
See discussion in thread:
https://lists.freedesktop.org/archives/dri-devel/2016-October/122370.html
Prime export tested on Intel iGPU + AMD Tonga dGPU as
DRI3/Present Prime render offload, and with the Tonga
standalone as primary gpu.
v2: Add a wait for all shared fences before prime export,
as suggested by Christian Koenig.
v3: - Mark buffer prime_exported in amdgpu_gem_prime_pin,
so we only use the exclusive fence when exporting a
bo to external clients like a separate iGPU, but not
when exporting/importing from/to ourselves as part of
regular DRI3 fd passing.
- Propagate failure of reservation_object_wait_rcu back
to caller.
v4: - Switch to a prime_shared_count counter instead of a
flag, which gets in/decremented on prime_pin/unpin, so
we can switch back to shared fences if all clients
detach from our exported bo.
- Also switch to exclusive fence for prime imported bo's.
v5: - Drop lret, instead use int ret -> long ret, as proposed
by Christian.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=95472
Tested-by: Mike Lothian <mike@fireburn.co.uk> (v1)
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>.
Cc: Christian König <christian.koenig@amd.com>
Cc: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
It is assuming that the card related information is located on
"card" node, but graph case doesn't have it.
This patch adds node parameter to adjust for graph support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_get_dai_name() is used from snd_soc_of_get_dai_name(),
and it is assuming that DT is using "sound-dai" / "#sound-dai-cells".
But graph base DT is using "remote-endpoint". This patch makes
snd_soc_get_dai_name() non static for graph support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is assuming that the card related information is located on
"card" node, but graph case doesn't have it.
This patch adds node parameter to adjust for graph support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After this patch only conversion of INTEL_INFO(p)->gen to
INTEL_GEN(dev_priv) remains before the __I915__ macro can
be removed.
v2: Tidy vlv_compute_wm. (David Weinehall)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>