commit 9d739bccf2 upstream.
There is chip (ls1028a) errata:
The SoC may hang on 16 byte unaligned read transactions by QDMA.
Unaligned read transactions initiated by QDMA may stall in the NOC
(Network On-Chip), causing a deadlock condition. Stalled transactions will
trigger completion timeouts in PCIe controller.
Workaround:
Enable prefetch by setting the source descriptor prefetchable bit
( SD[PF] = 1 ).
Implement this workaround.
Cc: stable@vger.kernel.org
Fixes: b092529e0a ("dmaengine: fsl-qdma: Add qDMA controller driver for Layerscape SoCs")
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240201215007.439503-1-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f41900e4a6 upstream.
There is a corner case here where start/end is after/before the block
range we are currently checking. If so we need to be sure that splitting
the block will eventually give use the block size we need. To do that we
should adjust the block range to account for the start/end, and only
continue with the split if the size/alignment will fit the requested
size. Not doing so can result in leaving split blocks unmerged when it
eventually fails.
Fixes: afea229fe1 ("drm: improve drm_buddy_alloc function")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: <stable@vger.kernel.org> # v5.18+
Reviewed-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240219121851.25774-4-matthew.auld@intel.com
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5897710b28 upstream.
If we have a sparse file with a trailing hole (from the last extent's end
to i_size) and then create an extent in the file that ends before the
file's i_size, then when doing an incremental send we will issue a write
full of zeroes for the range that starts immediately after the new extent
ends up to i_size. While this isn't incorrect because the file ends up
with exactly the same data, it unnecessarily results in using extra space
at the destination with one or more extents full of zeroes instead of
having a hole. In same cases this results in using megabytes or even
gigabytes of unnecessary space.
Example, reproducer:
$ cat test.sh
#!/bin/bash
DEV=/dev/sdh
MNT=/mnt/sdh
mkfs.btrfs -f $DEV
mount $DEV $MNT
# Create 1G sparse file.
xfs_io -f -c "truncate 1G" $MNT/foobar
# Create base snapshot.
btrfs subvolume snapshot -r $MNT $MNT/mysnap1
# Create send stream (full send) for the base snapshot.
btrfs send -f /tmp/1.snap $MNT/mysnap1
# Now write one extent at the beginning of the file and one somewhere
# in the middle, leaving a gap between the end of this second extent
# and the file's size.
xfs_io -c "pwrite -S 0xab 0 128K" \
-c "pwrite -S 0xcd 512M 128K" \
$MNT/foobar
# Now create a second snapshot which is going to be used for an
# incremental send operation.
btrfs subvolume snapshot -r $MNT $MNT/mysnap2
# Create send stream (incremental send) for the second snapshot.
btrfs send -p $MNT/mysnap1 -f /tmp/2.snap $MNT/mysnap2
# Now recreate the filesystem by receiving both send streams and
# verify we get the same content that the original filesystem had
# and file foobar has only two extents with a size of 128K each.
umount $MNT
mkfs.btrfs -f $DEV
mount $DEV $MNT
btrfs receive -f /tmp/1.snap $MNT
btrfs receive -f /tmp/2.snap $MNT
echo -e "\nFile fiemap in the second snapshot:"
# Should have:
#
# 128K extent at file range [0, 128K[
# hole at file range [128K, 512M[
# 128K extent file range [512M, 512M + 128K[
# hole at file range [512M + 128K, 1G[
xfs_io -r -c "fiemap -v" $MNT/mysnap2/foobar
# File should be using 256K of data (two 128K extents).
echo -e "\nSpace used by the file: $(du -h $MNT/mysnap2/foobar | cut -f 1)"
umount $MNT
Running the test, we can see with fiemap that we get an extent for the
range [512M, 1G[, while in the source filesystem we have an extent for
the range [512M, 512M + 128K[ and a hole for the rest of the file (the
range [512M + 128K, 1G[):
$ ./test.sh
(...)
File fiemap in the second snapshot:
/mnt/sdh/mysnap2/foobar:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..255]: 26624..26879 256 0x0
1: [256..1048575]: hole 1048320
2: [1048576..2097151]: 2156544..3205119 1048576 0x1
Space used by the file: 513M
This happens because once we finish processing an inode, at
finish_inode_if_needed(), we always issue a hole (write operations full
of zeros) if there's a gap between the end of the last processed extent
and the file's size, even if that range is already a hole in the parent
snapshot. Fix this by issuing the hole only if the range is not already
a hole.
After this change, running the test above, we get the expected layout:
$ ./test.sh
(...)
File fiemap in the second snapshot:
/mnt/sdh/mysnap2/foobar:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..255]: 26624..26879 256 0x0
1: [256..1048575]: hole 1048320
2: [1048576..1048831]: 26880..27135 256 0x1
3: [1048832..2097151]: hole 1048320
Space used by the file: 256K
A test case for fstests will follow soon.
CC: stable@vger.kernel.org # 6.1+
Reported-by: Dorai Ashok S A <dash.btrfs@inix.me>
Link: https://lore.kernel.org/linux-btrfs/c0bf7818-9c45-46a8-b3d3-513230d0c86e@inix.me/
Reviewed-by: Sweet Tea Dorminy <sweettea-kernel@dorminy.me>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2b54eaf28 upstream.
When creating a snapshot we may do a double free of an anonymous device
in case there's an error committing the transaction. The second free may
result in freeing an anonymous device number that was allocated by some
other subsystem in the kernel or another btrfs filesystem.
The steps that lead to this:
1) At ioctl.c:create_snapshot() we allocate an anonymous device number
and assign it to pending_snapshot->anon_dev;
2) Then we call btrfs_commit_transaction() and end up at
transaction.c:create_pending_snapshot();
3) There we call btrfs_get_new_fs_root() and pass it the anonymous device
number stored in pending_snapshot->anon_dev;
4) btrfs_get_new_fs_root() frees that anonymous device number because
btrfs_lookup_fs_root() returned a root - someone else did a lookup
of the new root already, which could some task doing backref walking;
5) After that some error happens in the transaction commit path, and at
ioctl.c:create_snapshot() we jump to the 'fail' label, and after
that we free again the same anonymous device number, which in the
meanwhile may have been reallocated somewhere else, because
pending_snapshot->anon_dev still has the same value as in step 1.
Recently syzbot ran into this and reported the following trace:
------------[ cut here ]------------
ida_free called for id=51 which is not allocated.
WARNING: CPU: 1 PID: 31038 at lib/idr.c:525 ida_free+0x370/0x420 lib/idr.c:525
Modules linked in:
CPU: 1 PID: 31038 Comm: syz-executor.2 Not tainted 6.8.0-rc4-syzkaller-00410-gc02197fc9076 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/25/2024
RIP: 0010:ida_free+0x370/0x420 lib/idr.c:525
Code: 10 42 80 3c 28 (...)
RSP: 0018:ffffc90015a67300 EFLAGS: 00010246
RAX: be5130472f5dd000 RBX: 0000000000000033 RCX: 0000000000040000
RDX: ffffc90009a7a000 RSI: 000000000003ffff RDI: 0000000000040000
RBP: ffffc90015a673f0 R08: ffffffff81577992 R09: 1ffff92002b4cdb4
R10: dffffc0000000000 R11: fffff52002b4cdb5 R12: 0000000000000246
R13: dffffc0000000000 R14: ffffffff8e256b80 R15: 0000000000000246
FS: 00007fca3f4b46c0(0000) GS:ffff8880b9500000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f167a17b978 CR3: 000000001ed26000 CR4: 0000000000350ef0
Call Trace:
<TASK>
btrfs_get_root_ref+0xa48/0xaf0 fs/btrfs/disk-io.c:1346
create_pending_snapshot+0xff2/0x2bc0 fs/btrfs/transaction.c:1837
create_pending_snapshots+0x195/0x1d0 fs/btrfs/transaction.c:1931
btrfs_commit_transaction+0xf1c/0x3740 fs/btrfs/transaction.c:2404
create_snapshot+0x507/0x880 fs/btrfs/ioctl.c:848
btrfs_mksubvol+0x5d0/0x750 fs/btrfs/ioctl.c:998
btrfs_mksnapshot+0xb5/0xf0 fs/btrfs/ioctl.c:1044
__btrfs_ioctl_snap_create+0x387/0x4b0 fs/btrfs/ioctl.c:1306
btrfs_ioctl_snap_create_v2+0x1ca/0x400 fs/btrfs/ioctl.c:1393
btrfs_ioctl+0xa74/0xd40
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:871 [inline]
__se_sys_ioctl+0xfe/0x170 fs/ioctl.c:857
do_syscall_64+0xfb/0x240
entry_SYSCALL_64_after_hwframe+0x6f/0x77
RIP: 0033:0x7fca3e67dda9
Code: 28 00 00 00 (...)
RSP: 002b:00007fca3f4b40c8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007fca3e7abf80 RCX: 00007fca3e67dda9
RDX: 00000000200005c0 RSI: 0000000050009417 RDI: 0000000000000003
RBP: 00007fca3e6ca47a R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 000000000000000b R14: 00007fca3e7abf80 R15: 00007fff6bf95658
</TASK>
Where we get an explicit message where we attempt to free an anonymous
device number that is not currently allocated. It happens in a different
code path from the example below, at btrfs_get_root_ref(), so this change
may not fix the case triggered by syzbot.
To fix at least the code path from the example above, change
btrfs_get_root_ref() and its callers to receive a dev_t pointer argument
for the anonymous device number, so that in case it frees the number, it
also resets it to 0, so that up in the call chain we don't attempt to do
the double free.
CC: stable@vger.kernel.org # 5.10+
Link: https://lore.kernel.org/linux-btrfs/000000000000f673a1061202f630@google.com/
Fixes: e03ee2fe87 ("btrfs: do not ASSERT() if the newly created subvolume already got read")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f78c137533 upstream.
It's currently possible to change the mesh ID when the
interface isn't yet in mesh mode, at the same time as
changing it into mesh mode. This leads to an overwrite
of data in the wdev->u union for the interface type it
currently has, causing cfg80211_change_iface() to do
wrong things when switching.
We could probably allow setting an interface to mesh
while setting the mesh ID at the same time by doing a
different order of operations here, but realistically
there's no userspace that's going to do this, so just
disallow changes in iftype when setting mesh ID.
Cc: stable@vger.kernel.org
Fixes: 29cbe68c51 ("cfg80211/mac80211: add mesh join/leave commands")
Reported-by: syzbot+dd4779978217b1973180@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9818b3e90 upstream.
When linking or renaming a file, if only one of the source or
destination directory is backed by an S_PRIVATE inode, then the related
set of layer masks would be used as uninitialized by
is_access_to_paths_allowed(). This would result to indeterministic
access for one side instead of always being allowed.
This bug could only be triggered with a mounted filesystem containing
both S_PRIVATE and !S_PRIVATE inodes, which doesn't seem possible.
The collect_domain_accesses() calls return early if
is_nouser_or_private() returns false, which means that the directory's
superblock has SB_NOUSER or its inode has S_PRIVATE. Because rename or
link actions are only allowed on the same mounted filesystem, the
superblock is always the same for both source and destination
directories. However, it might be possible in theory to have an
S_PRIVATE parent source inode with an !S_PRIVATE parent destination
inode, or vice versa.
To make sure this case is not an issue, explicitly initialized both set
of layer masks to 0, which means to allow all actions on the related
side. If at least on side has !S_PRIVATE, then
collect_domain_accesses() and is_access_to_paths_allowed() check for the
required access rights.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Günther Noack <gnoack@google.com>
Cc: Jann Horn <jannh@google.com>
Cc: Shervin Oloumi <enlightened@chromium.org>
Cc: stable@vger.kernel.org
Fixes: b91c3e4ea7 ("landlock: Add support for file reparenting with LANDLOCK_ACCESS_FS_REFER")
Link: https://lore.kernel.org/r/20240219190345.2928627-1-mic@digikod.net
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67c3d7717e upstream.
The HP mt440 Thin Client uses an ALC236 codec and needs the
ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF quirk to make the mute and
micmute LEDs work.
There are two variants of the USB-C PD chip on this device. Each uses
a different BIOS and board ID, hence the two entries.
Signed-off-by: Eniac Zhang <eniac-xw.zhang@hp.com>
Signed-off-by: Alexandru Gagniuc <alexandru.gagniuc@hp.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240220175812.782687-1-alexandru.gagniuc@hp.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1fdf4e8be7 upstream.
On my EliteBook 840 G8 Notebook PC (ProdId 5S7R6EC#ABD; built 2022 for
german market) the Mute LED is always on. The mute button itself works
as expected. alsa-info.sh shows a different subsystem-id 0x8ab9 for
Realtek ALC285 Codec, thus the existing quirks for HP 840 G8 don't work.
Therefore, add a new quirk for this type of EliteBook.
Signed-off-by: Hans Peter <flurry123@gmx.ch>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240219164518.4099-1-flurry123@gmx.ch
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77ce96543b upstream.
The local helper function to compare the given pair of cycle count
evaluates them. If the left value is less than the right value, the
function returns negative value.
If the safe cycle is less than the current cycle, it is the case of
cycle lost. However, it is not currently handled properly.
This commit fixes the bug.
Cc: <stable@vger.kernel.org>
Fixes: 705794c53b ("ALSA: firewire-lib: check cycle continuity")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20240218033026.72577-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f03fc340c upstream.
Since tomoyo_write_control() updates head->write_buf when write()
of long lines is requested, we need to fetch head->write_buf after
head->io_sem is held. Otherwise, concurrent write() requests can
cause use-after-free-write and double-free problems.
Reported-by: Sam Sun <samsun1006219@gmail.com>
Closes: https://lkml.kernel.org/r/CAEkJfYNDspuGxYx5kym8Lvp--D36CMDUErg4rxfWFJuPbbji8g@mail.gmail.com
Fixes: bd03a3e4c9 ("TOMOYO: Add policy namespace support.")
Cc: <stable@vger.kernel.org> # Linux 3.1+
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7cb50f6c9f ]
Introduced a stupid bug in commit 782bfd03c3 ("of: property: Improve
finding the supplier of a remote-endpoint property") due to a last minute
incorrect edit of "index !=0" into "!index". This patch fixes it to be
"index > 0" to match the comment right next to it.
Reported-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://lore.kernel.org/lkml/20240223171849.10f9901d@booty/
Fixes: 782bfd03c3 ("of: property: Improve finding the supplier of a remote-endpoint property")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://lore.kernel.org/r/20240224052436.3552333-1-saravanak@google.com
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a11dd49dcb ]
Offset vmemmap so that the first page of vmemmap will be mapped
to the first page of physical memory in order to ensure that
vmemmap’s bounds will be respected during
pfn_to_page()/page_to_pfn() operations.
The conversion macros will produce correct SV39/48/57 addresses
for every possible/valid DRAM_BASE inside the physical memory limits.
v2:Address Alex's comments
Suggested-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Signed-off-by: Dimitris Vlachos <dvlachos@ics.forth.gr>
Reported-by: Dimitris Vlachos <dvlachos@ics.forth.gr>
Closes: https://lore.kernel.org/linux-riscv/20240202135030.42265-1-csd4492@csd.uoc.gr
Fixes: d95f1a542c ("RISC-V: Implement sparsemem")
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20240229191723.32779-1-dvlachos@ics.forth.gr
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f7a076466 ]
If a directory has a block with only ".__afsXXXX" files in it (from
uncompleted silly-rename), these .__afsXXXX files are skipped but without
advancing the file position in the dir_context. This leads to
afs_dir_iterate() repeating the block again and again.
Fix this by making the code that skips the .__afsXXXX file also manually
advance the file position.
The symptoms are a soft lookup:
watchdog: BUG: soft lockup - CPU#3 stuck for 52s! [check:5737]
...
RIP: 0010:afs_dir_iterate_block+0x39/0x1fd
...
? watchdog_timer_fn+0x1a6/0x213
...
? asm_sysvec_apic_timer_interrupt+0x16/0x20
? afs_dir_iterate_block+0x39/0x1fd
afs_dir_iterate+0x10a/0x148
afs_readdir+0x30/0x4a
iterate_dir+0x93/0xd3
__do_sys_getdents64+0x6b/0xd4
This is almost certainly the actual fix for:
https://bugzilla.kernel.org/show_bug.cgi?id=218496
Fixes: 57e9d49c54 ("afs: Hide silly-rename files from userspace")
Signed-off-by: David Howells <dhowells@redhat.com>
Link: https://lore.kernel.org/r/786185.1708694102@warthog.procyon.org.uk
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Markus Suvanto <markus.suvanto@gmail.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00d6a284fc ]
Commit a5a923038d (fbdev: fbcon: Properly revert changes when
vc_resize() failed) started restoring old font data upon failure (of
vc_resize()). But it performs so only for user fonts. It means that the
"system"/internal fonts are not restored at all. So in result, the very
first call to fbcon_do_set_font() performs no restore at all upon
failing vc_resize().
This can be reproduced by Syzkaller to crash the system on the next
invocation of font_get(). It's rather hard to hit the allocation failure
in vc_resize() on the first font_set(), but not impossible. Esp. if
fault injection is used to aid the execution/failure. It was
demonstrated by Sirius:
BUG: unable to handle page fault for address: fffffffffffffff8
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD cb7b067 P4D cb7b067 PUD cb7d067 PMD 0
Oops: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 8007 Comm: poc Not tainted 6.7.0-g9d1694dc91ce #20
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
RIP: 0010:fbcon_get_font+0x229/0x800 drivers/video/fbdev/core/fbcon.c:2286
Call Trace:
<TASK>
con_font_get drivers/tty/vt/vt.c:4558 [inline]
con_font_op+0x1fc/0xf20 drivers/tty/vt/vt.c:4673
vt_k_ioctl drivers/tty/vt/vt_ioctl.c:474 [inline]
vt_ioctl+0x632/0x2ec0 drivers/tty/vt/vt_ioctl.c:752
tty_ioctl+0x6f8/0x1570 drivers/tty/tty_io.c:2803
vfs_ioctl fs/ioctl.c:51 [inline]
...
So restore the font data in any case, not only for user fonts. Note the
later 'if' is now protected by 'old_userfont' and not 'old_data' as the
latter is always set now. (And it is supposed to be non-NULL. Otherwise
we would see the bug above again.)
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Fixes: a5a923038d ("fbdev: fbcon: Properly revert changes when vc_resize() failed")
Reported-and-tested-by: Ubisectech Sirius <bugreport@ubisectech.com>
Cc: Ubisectech Sirius <bugreport@ubisectech.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20240208114411.14604-1-jirislaby@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86bf8cfda6 ]
Tegra DRM doesn't support display on Tegra234 and later, so make sure
not to remove any existing framebuffers in that case.
v2: - add comments explaining how this situation can come about
- clear DRIVER_MODESET and DRIVER_ATOMIC feature bits
Fixes: 6848c291a5 ("drm/aperture: Convert drivers to aperture interfaces")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240223150333.1401582-1-thierry.reding@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4df49712eb ]
We forgot to remove the line for snd-rtctimer from Makefile while
dropping the functionality. Get rid of the stale line.
Fixes: 34ce71a96d ("ALSA: timer: remove legacy rtctimer")
Link: https://lore.kernel.org/r/20240221092156.28695-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2df70149e7 ]
The bq27xxx i2c-client may not have an IRQ, in which case
client->irq will be 0. bq27xxx_battery_i2c_probe() already has
an if (client->irq) check wrapping the request_threaded_irq().
But bq27xxx_battery_i2c_remove() unconditionally calls
free_irq(client->irq) leading to:
[ 190.310742] ------------[ cut here ]------------
[ 190.310843] Trying to free already-free IRQ 0
[ 190.310861] WARNING: CPU: 2 PID: 1304 at kernel/irq/manage.c:1893 free_irq+0x1b8/0x310
Followed by a backtrace when unbinding the driver. Add
an if (client->irq) to bq27xxx_battery_i2c_remove() mirroring
probe() to fix this.
Fixes: 444ff00734 ("power: supply: bq27xxx: Fix I2C IRQ race on remove")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240215155133.70537-1-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fccfa646ef ]
gcc-14 notices that the allocation with sizeof(void) on 32-bit architectures
is not enough for a 64-bit phys_addr_t:
drivers/firmware/efi/capsule-loader.c: In function 'efi_capsule_open':
drivers/firmware/efi/capsule-loader.c:295:24: error: allocation of insufficient size '4' for type 'phys_addr_t' {aka 'long long unsigned int'} with size '8' [-Werror=alloc-size]
295 | cap_info->phys = kzalloc(sizeof(void *), GFP_KERNEL);
| ^
Use the correct type instead here.
Fixes: f24c4d4780 ("efi/capsule-loader: Reinstate virtual capsule mapping")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6caaf10442 ]
If we peek from 2 records with a currently empty rx_list, and the
first record is decrypted synchronously but the second record is
decrypted async, the following happens:
1. decrypt record 1 (sync)
2. copy from record 1 to the userspace's msg
3. queue the decrypted record to rx_list for future read(!PEEK)
4. decrypt record 2 (async)
5. queue record 2 to rx_list
6. call process_rx_list to copy data from the 2nd record
We currently pass copied=0 as skip offset to process_rx_list, so we
end up copying once again from the first record. We should skip over
the data we've already copied.
Seen with selftest tls.12_aes_gcm.recv_peek_large_buf_mult_recs
Fixes: 692d7b5d1f ("tls: Fix recvmsg() to be able to peek across multiple records")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/1b132d2b2b99296bfde54e8a67672d90d6d16e71.1709132643.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7fa16d498 ]
With mixed sync/async decryption, or failures of crypto_aead_decrypt,
we increment decrypt_pending but we never do the corresponding
decrement since tls_decrypt_done will not be called. In this case, we
should decrement decrypt_pending immediately to avoid getting stuck.
For example, the prequeue prequeue test gets stuck with mixed
modes (one async decrypt + one sync decrypt).
Fixes: 94524d8fc9 ("net/tls: Add support for async decryption of tls records")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/c56d5fc35543891d5319f834f25622360e1bfbec.1709132643.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51dd4ee037 ]
Current HSR implementation uses following supervisory frame (even for
HSRv1 the HSR tag is not is not present):
00000000: 01 15 4e 00 01 2d XX YY ZZ 94 77 10 88 fb 00 01
00000010: 7e 1c 17 06 XX YY ZZ 94 77 10 1e 06 XX YY ZZ 94
00000020: 77 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000030: 00 00 00 00 00 00 00 00 00 00 00 00
The current code adds extra two bytes (i.e. sizeof(struct hsr_sup_tlv))
when offset for skb_pull() is calculated.
This is wrong, as both 'struct hsrv1_ethhdr_sp' and 'hsrv0_ethhdr_sp'
already have 'struct hsr_sup_tag' defined in them, so there is no need
for adding extra two bytes.
This code was working correctly as with no RedBox support, the check for
HSR_TLV_EOT (0x00) was off by two bytes, which were corresponding to
zeroed padded bytes for minimal packet size.
Fixes: eafaa88b3e ("net: hsr: Add support for redbox supervision frames")
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240228085644.3618044-1-lukma@denx.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0bb7b09392 ]
The i211 requires the same PTP timestamp adjustments as the i210,
according to its datasheet. To ensure consistent timestamping across
different platforms, this change extends the existing adjustments to
include the i211.
The adjustment result are tested and comparable for i210 and i211 based
systems.
Fixes: 3f544d2a4d ("igb: adjust PTP timestamps for Tx/Rx latency")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240227184942.362710-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 743ad091fb ]
In the commit d73ef2d69c ("rtnetlink: let rtnl_bridge_setlink checks
IFLA_BRIDGE_MODE length"), an adjustment was made to the old loop logic
in the function `rtnl_bridge_setlink` to enable the loop to also check
the length of the IFLA_BRIDGE_MODE attribute. However, this adjustment
removed the `break` statement and led to an error logic of the flags
writing back at the end of this function.
if (have_flags)
memcpy(nla_data(attr), &flags, sizeof(flags));
// attr should point to IFLA_BRIDGE_FLAGS NLA !!!
Before the mentioned commit, the `attr` is granted to be IFLA_BRIDGE_FLAGS.
However, this is not necessarily true fow now as the updated loop will let
the attr point to the last NLA, even an invalid NLA which could cause
overflow writes.
This patch introduces a new variable `br_flag` to save the NLA pointer
that points to IFLA_BRIDGE_FLAGS and uses it to resolve the mentioned
error logic.
Fixes: d73ef2d69c ("rtnetlink: let rtnl_bridge_setlink checks IFLA_BRIDGE_MODE length")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20240227121128.608110-1-linma@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62e7151ae3 ]
conntrack nf_confirm logic cannot handle cloned skbs referencing
the same nf_conn entry, which will happen for multicast (broadcast)
frames on bridges.
Example:
macvlan0
|
br0
/ \
ethX ethY
ethX (or Y) receives a L2 multicast or broadcast packet containing
an IP packet, flow is not yet in conntrack table.
1. skb passes through bridge and fake-ip (br_netfilter)Prerouting.
-> skb->_nfct now references a unconfirmed entry
2. skb is broad/mcast packet. bridge now passes clones out on each bridge
interface.
3. skb gets passed up the stack.
4. In macvlan case, macvlan driver retains clone(s) of the mcast skb
and schedules a work queue to send them out on the lower devices.
The clone skb->_nfct is not a copy, it is the same entry as the
original skb. The macvlan rx handler then returns RX_HANDLER_PASS.
5. Normal conntrack hooks (in NF_INET_LOCAL_IN) confirm the orig skb.
The Macvlan broadcast worker and normal confirm path will race.
This race will not happen if step 2 already confirmed a clone. In that
case later steps perform skb_clone() with skb->_nfct already confirmed (in
hash table). This works fine.
But such confirmation won't happen when eb/ip/nftables rules dropped the
packets before they reached the nf_confirm step in postrouting.
Pablo points out that nf_conntrack_bridge doesn't allow use of stateful
nat, so we can safely discard the nf_conn entry and let inet call
conntrack again.
This doesn't work for bridge netfilter: skb could have a nat
transformation. Also bridge nf prevents re-invocation of inet prerouting
via 'sabotage_in' hook.
Work around this problem by explicit confirmation of the entry at LOCAL_IN
time, before upper layer has a chance to clone the unconfirmed entry.
The downside is that this disables NAT and conntrack helpers.
Alternative fix would be to add locking to all code parts that deal with
unconfirmed packets, but even if that could be done in a sane way this
opens up other problems, for example:
-m physdev --physdev-out eth0 -j SNAT --snat-to 1.2.3.4
-m physdev --physdev-out eth1 -j SNAT --snat-to 1.2.3.5
For multicast case, only one of such conflicting mappings will be
created, conntrack only handles 1:1 NAT mappings.
Users should set create a setup that explicitly marks such traffic
NOTRACK (conntrack bypass) to avoid this, but we cannot auto-bypass
them, ruleset might have accept rules for untracked traffic already,
so user-visible behaviour would change.
Suggested-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217777
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2954fe60e3 ]
iptables/nftables support responding to tcp packets with tcp resets.
The generated tcp reset packet passes through both output and postrouting
netfilter hooks, but conntrack will never see them because the generated
skb has its ->nfct pointer copied over from the packet that triggered the
reset rule.
If the reset rule is used for established connections, this
may result in the conntrack entry to be around for a very long
time (default timeout is 5 days).
One way to avoid this would be to not copy the nf_conn pointer
so that the rest packet passes through conntrack too.
Problem is that output rules might not have the same conntrack
zone setup as the prerouting ones, so its possible that the
reset skb won't find the correct entry. Generating a template
entry for the skb seems error prone as well.
Add an explicit "closing" function that switches a confirmed
conntrack entry to closed state and wire this up for tcp.
If the entry isn't confirmed, no action is needed because
the conntrack entry will never be committed to the table.
Reported-by: Russel King <linux@armlinux.org.uk>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Stable-dep-of: 62e7151ae3 ("netfilter: bridge: confirm multicast packets before passing them up the stack")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e0f122c65 ]
Commit d0009effa8 ("netfilter: nf_tables: validate NFPROTO_* family") added
some validation of NFPROTO_* families in the nft_compat module, but it broke
the ability to use legacy iptables modules in dual-stack nftables.
While with legacy iptables one had to independently manage IPv4 and IPv6
tables, with nftables it is possible to have dual-stack tables sharing the
rules. Moreover, it was possible to use rules based on legacy iptables
match/target modules in dual-stack nftables.
As an example, the program from [2] creates an INET dual-stack family table
using an xt_bpf based rule, which looks like the following (the actual output
was generated with a patched nft tool as the current nft tool does not parse
dual stack tables with legacy match rules, so consider it for illustrative
purposes only):
table inet testfw {
chain input {
type filter hook prerouting priority filter; policy accept;
bytecode counter packets 0 bytes 0 accept
}
}
After d0009effa8 ("netfilter: nf_tables: validate NFPROTO_* family") we get
EOPNOTSUPP for the above program.
Fix this by allowing NFPROTO_INET for nft_(match/target)_validate(), but also
restrict the functions to classic iptables hooks.
Changes in v3:
* clarify that upstream nft will not display such configuration properly and
that the output was generated with a patched nft tool
* remove example program from commit description and link to it instead
* no code changes otherwise
Changes in v2:
* restrict nft_(match/target)_validate() to classic iptables hooks
* rewrite example program to use unmodified libnftnl
Fixes: d0009effa8 ("netfilter: nf_tables: validate NFPROTO_* family")
Link: https://lore.kernel.org/all/Zc1PfoWN38UuFJRI@calendula/T/#mc947262582c90fec044c7a3398cc92fac7afea72 [1]
Link: https://lore.kernel.org/all/20240220145509.53357-1-ignat@cloudflare.com/ [2]
Reported-by: Jordan Griege <jgriege@cloudflare.com>
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7dcd3e014a ]
BT adapter going into UNCONFIGURED state during BT turn ON when
devicetree has no local-bd-address node.
Bluetooth will not work out of the box on such devices, to avoid this
problem, added check to set HCI_QUIRK_USE_BDADDR_PROPERTY based on
local-bd-address node entry.
When this quirk is not set, the public Bluetooth address read by host
from controller though HCI Read BD Address command is
considered as valid.
Fixes: e668eb1e15 ("Bluetooth: hci_core: Don't stop BT if the BD address missing in dts")
Signed-off-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0c1278ac8 ]
Add support for the WCN7850 Bluetooth chipset.
Tested on the SM8550 QRD platform.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 7dcd3e014a ("Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 691d54d0f7 ]
Use switch/case to handle soc type specific behaviour,
the permit dropping the qca_is_xxx() inline functions
and make the code clearer and easier to update for new
SoCs.
Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Suggested-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 7dcd3e014a ("Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f904feefe6 ]
Add support for the Bluetooth chip codenamed APACHE which is part of
WCN3988.
The firmware for this chip has a slightly different naming scheme
compared to most others. For ROM Version 0x0200 we need to use
apbtfw10.tlv + apnv10.bin and for ROM version 0x201 apbtfw11.tlv +
apnv11.bin
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 7dcd3e014a ("Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8153b738bc ]
Use le32_to_cpu for ver.soc_id to fix the following
sparse warning.
drivers/bluetooth/btqca.c:640:24: sparse: warning: restricted
__le32 degrades to integer
Signed-off-by: Min-Hua Chen <minhuadotchen@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 7dcd3e014a ("Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 095327fede ]
Add regulators, GPIOs and changes required to power on/off wcn6855.
Add support for firmware download for wcn6855 which is in the
linux-firmware repository as hpbtfw21.tlv and hpnv21.bin.
Based on the assumption that this is similar to the wcn6750
Tested-on: BTFW.HSP.2.1.0-00538-VER_PATCHZ-1
Signed-off-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Tested-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 7dcd3e014a ("Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44fac8a2fd ]
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/bluetooth/hci_qca.c:1869:37: error: ‘qca_soc_data_wcn6750’
defined but not used [-Werror=unused-const-variable=]
drivers/bluetooth/hci_qca.c:1853:37: error: ‘qca_soc_data_wcn3998’
defined but not used [-Werror=unused-const-variable=]
drivers/bluetooth/hci_qca.c:1841:37: error: ‘qca_soc_data_wcn3991’
defined but not used [-Werror=unused-const-variable=]
drivers/bluetooth/hci_qca.c:1830:37: error: ‘qca_soc_data_wcn3990’
defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 7dcd3e014a ("Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4b019515f ]
Right now Linux BT stack cannot pass test case "GAP/CONN/CPUP/BV-05-C
'Connection Parameter Update Procedure Invalid Parameters Central
Responder'" in Bluetooth Test Suite revision GAP.TS.p44. [0]
That was revoled by commit c49a8682fc ("Bluetooth: validate BLE
connection interval updates"), but later got reverted due to devices
like keyboards and mice may require low connection interval.
So only validate the max value connection interval to pass the Test
Suite, and let devices to request low connection interval if needed.
[0] https://www.bluetooth.org/docman/handlers/DownloadDoc.ashx?doc_id=229869
Fixes: 68d19d7d99 ("Revert "Bluetooth: validate BLE connection interval updates"")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61a5ab72ed ]
hci_store_wake_reason() wrongly parses event HCI_Connection_Request
as HCI_Connection_Complete and HCI_Connection_Complete as
HCI_Connection_Request, so causes recording wakeup BD_ADDR error and
potential stability issue, fix it by using the correct field.
Fixes: 2f20216c1d ("Bluetooth: Emit controller suspend and resume events")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5469adb2a ]
During suspend, only wakeable devices can be in acceptlist, so if the
device was previously added it needs to be removed otherwise the device
can end up waking up the system prematurely.
Fixes: 3b42055388 ("Bluetooth: hci_sync: Fix attempting to suspend with unfiltered passive scan")
Signed-off-by: Clancy Shang <clancy.shang@quectel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2449007d3f ]
While handling the HCI_EV_HARDWARE_ERROR event, if the underlying
BT controller is not responding, the GPIO reset mechanism would
free the hci_dev and lead to a use-after-free in hci_error_reset.
Here's the call trace observed on a ChromeOS device with Intel AX201:
queue_work_on+0x3e/0x6c
__hci_cmd_sync_sk+0x2ee/0x4c0 [bluetooth <HASH:3b4a6>]
? init_wait_entry+0x31/0x31
__hci_cmd_sync+0x16/0x20 [bluetooth <HASH:3b4a 6>]
hci_error_reset+0x4f/0xa4 [bluetooth <HASH:3b4a 6>]
process_one_work+0x1d8/0x33f
worker_thread+0x21b/0x373
kthread+0x13a/0x152
? pr_cont_work+0x54/0x54
? kthread_blkcg+0x31/0x31
ret_from_fork+0x1f/0x30
This patch holds the reference count on the hci_dev while processing
a HCI_EV_HARDWARE_ERROR event to avoid potential crash.
Fixes: c7741d16a5 ("Bluetooth: Perform a power cycle when receiving hardware error event")
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b3899be24 ]
There's a very confusing mistake in the code starting a HCI inquiry: We're
calling hci_dev_test_flag() to test for HCI_INQUIRY, but hci_dev_test_flag()
checks hdev->dev_flags instead of hdev->flags. HCI_INQUIRY is a bit that's
set on hdev->flags, not on hdev->dev_flags though.
HCI_INQUIRY equals the integer 7, and in hdev->dev_flags, 7 means
HCI_BONDABLE, so we were actually checking for HCI_BONDABLE here.
The mistake is only present in the synchronous code for starting an inquiry,
not in the async one. Also devices are typically bondable while doing an
inquiry, so that might be the reason why nobody noticed it so far.
Fixes: abfeea476c ("Bluetooth: hci_sync: Convert MGMT_OP_START_DISCOVERY")
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8af411bbba ]
Currently when suspending driver and stopping workqueue it is checked whether
workqueue is not NULL and if so, it is destroyed.
Function destroy_workqueue() does drain queue and does clear variable, but
it does not set workqueue variable to NULL. This can cause kernel/module
panic if code attempts to clear workqueue that was not initialized.
This scenario is possible when resuming suspended driver in stmmac_resume(),
because there is no handling for failed stmmac_hw_setup(),
which can fail and return if DMA engine has failed to initialize,
and workqueue is initialized after DMA engine.
Should DMA engine fail to initialize, resume will proceed normally,
but interface won't work and TX queue will eventually timeout,
causing 'Reset adapter' error.
This then does destroy workqueue during reset process.
And since workqueue is initialized after DMA engine and can be skipped,
it will cause kernel/module panic.
To secure against this possible crash, set workqueue variable to NULL when
destroying workqueue.
Log/backtrace from crash goes as follows:
[88.031977]------------[ cut here ]------------
[88.031985]NETDEV WATCHDOG: eth0 (sxgmac): transmit queue 1 timed out
[88.032017]WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:477 dev_watchdog+0x390/0x398
<Skipping backtrace for watchdog timeout>
[88.032251]---[ end trace e70de432e4d5c2c0 ]---
[88.032282]sxgmac 16d88000.ethernet eth0: Reset adapter.
[88.036359]------------[ cut here ]------------
[88.036519]Call trace:
[88.036523] flush_workqueue+0x3e4/0x430
[88.036528] drain_workqueue+0xc4/0x160
[88.036533] destroy_workqueue+0x40/0x270
[88.036537] stmmac_fpe_stop_wq+0x4c/0x70
[88.036541] stmmac_release+0x278/0x280
[88.036546] __dev_close_many+0xcc/0x158
[88.036551] dev_close_many+0xbc/0x190
[88.036555] dev_close.part.0+0x70/0xc0
[88.036560] dev_close+0x24/0x30
[88.036564] stmmac_service_task+0x110/0x140
[88.036569] process_one_work+0x1d8/0x4a0
[88.036573] worker_thread+0x54/0x408
[88.036578] kthread+0x164/0x170
[88.036583] ret_from_fork+0x10/0x20
[88.036588]---[ end trace e70de432e4d5c2c1 ]---
[88.036597]Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004
Fixes: 5a5586112b ("net: stmmac: support FPE link partner hand-shaking procedure")
Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a20086419 ]
Not really a fix per se, but IPV6_TLV_IOAM is still tagged as "TEMPORARY
IANA allocation for IOAM", while RFC 9486 is available for some time
now. Just update the reference.
Fixes: 9ee11f0fff ("ipv6: ioam: Data plane support for Pre-allocated Trace")
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240226124921.9097-1-justin.iurman@uliege.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3d5d70cb4 ]
Disable BH around the call to napi_schedule() to avoid following
error:
NOHZ tick-stop error: local softirq work is pending, handler #08!!!
Fixes: ec4c7e1239 ("lan78xx: Introduce NAPI polling support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240226110820.2113584-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c68b2c9eba ]
The MII code does not check the return value of mdio_read (among
others), and therefore no error code should be sent. A previous fix to
the use of an uninitialized variable propagates negative error codes,
that might lead to wrong operations by the MII library.
An example of such issues is the use of mii_nway_restart by the dm9601
driver. The mii_nway_restart function does not check the value returned
by mdio_read, which in this case might be a negative number which could
contain the exact bit the function checks (BMCR_ANENABLE = 0x1000).
Return zero in case of error, as it is common practice in users of
mdio_read to avoid wrong uses of the return value.
Fixes: 8f8abb863f ("net: usb: dm9601: fix uninitialized variable use in dm9601_mdio_read")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20240225-dm9601_ret_err-v1-1-02c1d959ea59@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ce7d306ea ]
struct veth_rq is pretty large, 832B total without debug
options enabled. Since commit under Fixes we try to pre-allocate
enough queues for every possible CPU. Miao Wang reports that
this may lead to order-5 allocations which will fail in production.
Let the allocation fallback to vmalloc() and try harder.
These are the same flags we pass to netdev queue allocation.
Reported-and-tested-by: Miao Wang <shankerwangmiao@gmail.com>
Fixes: 9d3684c24a ("veth: create by default nr_possible_cpus queues")
Link: https://lore.kernel.org/all/5F52CAE2-2FB7-4712-95F1-3312FBBFA8DD@gmail.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240223235908.693010-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e67899abf ]
Same as LAN7800, LAN7850 can be used without EEPROM. If EEPROM is not
present or not flashed, LAN7850 will fail to sync the speed detected by the PHY
with the MAC. In case link speed is 100Mbit, it will accidentally work,
otherwise no data can be transferred.
Better way would be to implement link_up callback, or set auto speed
configuration unconditionally. But this changes would be more intrusive.
So, for now, set it only if no EEPROM is found.
Fixes: e69647a19c ("lan78xx: Set ASD in MAC_CR when EEE is enabled.")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240222123839.2816561-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10bfd453da ]
It seems that if userspace provides a correct IFA_TARGET_NETNSID value
but no IFA_ADDRESS and IFA_LOCAL attributes, inet6_rtm_getaddr()
returns -EINVAL with an elevated "struct net" refcount.
Fixes: 6ecf4c37eb ("ipv6: enable IFA_TARGET_NETNSID for RTM_GETADDR")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
