Currently, if one new page allocated into fscache in readpage(), however,
with no data read into due to error encountered during reading from OSDs,
the slot in fscache is not uncached. This patch fixes this.
Signed-off-by: Li Wang <liwang@ubuntukylin.com>
Reviewed-by: Milosz Tanski <milosz@adfin.com>
Adds cap check to the page fault handler. The check prevents page
fault handler from adding new page to the page cache while Fcb caps
are being revoked. This solves Fc revoking hang in multiple clients
mmap IO workload.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Currently each rbd device is allocated its own major number, which
leads to a hard limit of 230-250 images mapped at once. This commit
adds support for a new single-major device number allocation scheme,
which is hidden behind a new single_major boolean module parameter and
is disabled by default for backwards compatibility reasons. (Old
userspace cannot correctly unmap images mapped under single-major
scheme and would essentially just unmap a random image, if that.)
$ rbd showmapped
id pool image snap device
0 rbd b100 - /dev/rbd0
1 rbd b101 - /dev/rbd1
2 rbd b102 - /dev/rbd2
3 rbd b103 - /dev/rbd3
Old scheme (modprobe rbd):
$ ls -l /dev/rbd*
brw-rw---- 1 root disk 253, 0 Dec 10 12:24 /dev/rbd0
brw-rw---- 1 root disk 252, 0 Dec 10 12:28 /dev/rbd1
brw-rw---- 1 root disk 252, 1 Dec 10 12:28 /dev/rbd1p1
brw-rw---- 1 root disk 252, 2 Dec 10 12:28 /dev/rbd1p2
brw-rw---- 1 root disk 252, 3 Dec 10 12:28 /dev/rbd1p3
brw-rw---- 1 root disk 251, 0 Dec 10 12:28 /dev/rbd2
brw-rw---- 1 root disk 251, 1 Dec 10 12:28 /dev/rbd2p1
brw-rw---- 1 root disk 250, 0 Dec 10 12:24 /dev/rbd3
New scheme (modprobe rbd single_major=Y):
$ ls -l /dev/rbd*
brw-rw---- 1 root disk 253, 0 Dec 10 12:30 /dev/rbd0
brw-rw---- 1 root disk 253, 256 Dec 10 12:30 /dev/rbd1
brw-rw---- 1 root disk 253, 257 Dec 10 12:30 /dev/rbd1p1
brw-rw---- 1 root disk 253, 258 Dec 10 12:30 /dev/rbd1p2
brw-rw---- 1 root disk 253, 259 Dec 10 12:30 /dev/rbd1p3
brw-rw---- 1 root disk 253, 512 Dec 10 12:30 /dev/rbd2
brw-rw---- 1 root disk 253, 513 Dec 10 12:30 /dev/rbd2p1
brw-rw---- 1 root disk 253, 768 Dec 10 12:30 /dev/rbd3
(major 253 was assigned dynamically at module load time)
The new limit is 4096 images mapped at once, and it comes from the fact
that, as before, 256 minor numbers are reserved for each mapping.
(A follow-up commit changes the number of minors reserved and the way
we deal with partitions over that number.)
If single_major is set to true, two new sysfs interfaces show up:
/sys/bus/rbd/{add,remove}_single_major. These are to be used instead
of /sys/bus/rbd/{add,remove}, which are disabled for backwards
compatibility reasons outlined above.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
In preparation for single-major device number allocation scheme, wire
up attribute_group::is_visible() callback for rbd bus. This allows us
to make the new single-major attributes conditional.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Introduce /sys/bus/rbd/devices/<id>/minor sysfs attribute for exporting
rbd whole disk minor numbers. This is a step towards single-major
device number allocation scheme, but also a good thing on its own.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Currently rbd ids are allocated using an atomic variable that keeps
track of the highest id currently in use and each new id is simply one
more than the value of that variable. That's nice and cheap, but it
does mean that rbd ids are allowed to grow boundlessly, and, more
importantly, it's completely unpredictable. So, in preparation for
single-major device number allocation scheme, which is going to
establish and rely on a constant mapping between rbd ids and device
numbers, switch to ida for rbd id assignments.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Refactor rbd_init() a bit to make it more clear what's going on.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Tweak "loaded" message, so that it looks like
[ 30.184235] rbd: loaded
instead of
[ 38.056564] rbd: loaded rbd (rados block device)
Also move (and slightly tweak) MODULE_DESCRIPTION so that all authors
are next to each other in modinfo output.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
rbd_device::dev_id is an int, format it as such.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Zhi Yong Wu says:
====================
tun: add the RFS support
Since Tom Herbert's hash related patchset was modified and got merged,
his pachset about adding support for RFS on tun flows also need to get
adjusted accordingly. I tried to update them, and before i will start
to do some perf tests, i hope to get one correct code base, so it's time
to post them out now. Any constructive comments are welcome, thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support so that the rps_flow_tables (RFS) can be
programmed using the tun flows which are already set up to track flows
for the purposes of queue selection.
On the receive path (corresponding to select_queue and tun_net_xmit) the
rxhash is saved in the flow_entry. The original code only does flow
lookup in select_queue, so this patch adds a flow lookup in tun_net_xmit
if num_queues == 1 (select_queue is not called from
dev_queue_xmit->netdev_pick_tx in that case).
The flow is recorded (processing CPU) in tun_flow_update (TX path), and
reset when flow is deleted.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds sock_rps_record_flow_hash and sock_rps_reset_flow_hash
which take a hash value as an argument and sets the sock_flow_table
accordingly. This allows the table to be populated in cases where flow
is being tracked outside of a sock structure.
sock_rps_record_flow and sock_rps_reset_flow call this function
where the hash is taken from sk_rxhash.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document the device tree binding for Broadcom Kona architecture
clock control units and clocks. Kona device nodes are represented
with compatible strings having "bcm11351" in their name.
Kona clocks are managed by "clock control units" (CCUs). Each CCU
has a device tree node, and within that node are defined the names
of the clocks provided by the CCU.
The BCM281xx family of SoCs use Kona CCUs and clocks.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Found by klocwork analysis.
mvm could be NULL which may cause a NULL dereference
in a theoretical call flow
rs_fill_lq_cmd(mvm = NULL, ...)
rs_build_rates_table
rs_fill_rates_for_column
ucode_rate_from_rs_rate
IWL_ERR(mvm,...)
No real reason for passing NULL to rs_fill_lq_cmd so fix that.
Reported-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently, the MAC context tsf_id assignment and the master/slave
relations are determined only when a new vif is added, as part
of the MAC context resource allocation. However, at this stage, the
beacon interval is not known, and thus could not be taken into account
in the master-slave algorithm.
To fix this, recalculate the MAC context tsf_id assignment,
just before the MAC context is activated, i.e., just before
a station VMAC is configured to associated and before an AP
VMAC is started.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Change the parameters for calculating an AP TBTT to 64/36 instead of
80/20, to increase the interval between a station vif and an AP
vif TBTT events.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The access to the CSR_RESET reg should be done as a complete
DWORD and not by setting a bit. This is the right way to reset
the device.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of always calling ieee80211_beacon_loss() on every missed
beacons notification, call this function only if the number of
consecutive missed beacons from last rx is higher than a predefined
threshold.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If the channel min-width changes, we can update the PHY ctx, even if
it has multiple references.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This allows to format it at will using external tools.
Since different teams want it in different formats, dump
the raw data and everyone can play with the data the way
they want.
While at it - make this code slightly more robust by making
the required verification on the offsets / length in the
write handler.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Don't check if mvm->fw->cs is NULL since it can't be.
cs is an array member of iwl_fw, it can't be NULL.
Use memset(ptr, 0, sizeof(*ptr)); instead of
memset(ptr, 0, sizeof(struct ptr_type));
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware needs to be stopped quickly (100ms) after the
RFKILL interrupt fired. Failing to do so would allow the
firmware to access the radio registers which would lead to
a hardware error.
Before this change, we would kill the firmware only when
mac80211 stops the device which can take a fair amount of
time. Take a shortcut by stopping the device right away
in the interrupt.
This is not relevant if the current firmware is INIT
firmware since that firmware can run while in RFKILL.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Calling stop_device when start_fw wasn't called would issue:
Stopping tx queues that aren't allocated...
Also allow the op_mode to call stop_device and then to
disable the Tx queues - in that case just silently ignore
the disabling on the Tx queues, since the PRPH registers
aren't reachable any more.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This is useless and introduces a dependency between rfkill
and stop_device - the op_mode can't call stop_device from
the rfkill notification since it would lead to an endless
recursion.
Next patches will need to do so.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Under very specific circumstances, the firmware might
ignore a host command. This was debugged and we ended up
seeing that the power management hardware was faulty.
In order to workaround this issue, we keep the NIC awake
as long as we have host commands in flight. This will avoid
to put the hardware into buggy condition.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case of invalid section_id, the function returns after
it aleready allocated memory. Fixed by change the order of actions.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The AC / fifo mapping was wrong - BE packets landed in VO
FIFO. The iwl_mvm_tx_fifo enumeration isn't in the same
order as ieee80211_ac_numbers enumeration.
Since the firmware relies on fifo / ac mapping - this led
to wrong behavior. E.g. the firmware sends beacon with the
same QoS parameters as VO, and it actually took the
parameters of BK. There are probably more severe issues.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
blk_mq_free_queue() is called from release handler of
queue kobject, so it needn't be called from drivers.
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch moves synchronization on mq->delay_work
from blk_mq_free_queue() to blk_sync_queue(), so that
blk_sync_queue can work on mq.
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_mq_drain_queue() is introduced so that we can drain
mq queue inside blk_cleanup_queue().
Also don't accept new requests any more if queue is marked
as dying.
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJSwLfoAAoJEHm+PkMAQRiGi6QH/1U1B7lmHChDTw3jj1lfm9gA
189Si4QJlnxFWCKHvKEL+pcaVuACU+aMGI8+KyMYK4/JfuWVjjj5fr/SvyHH2/8m
LdSK8aHMhJ46uBS4WJ/l6v46qQa5e2vn8RKSBAyKm/h4vpt+hd6zJdoFrFai4th7
k/TAwOAEHI5uzexUChwLlUBRTvbq4U8QUvDu+DeifC8cT63CGaaJ4qVzjOZrx1an
eP6UXZrKDASZs7RU950i7xnFVDQu4PsjlZi25udsbeiKcZJgPqGgXz5ULf8ZH8RQ
YCi1JOnTJRGGjyIOyLj7pyB01h7XiSM2+eMQ0S7g54F2s7gCJ58c2UwQX45vRWU=
=/4/R
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc6' into for-3.14/core
Needed to bring blk-mq uptodate, since changes have been going in
since for-3.14/core was established.
Fixup merge issues related to the immutable biovec changes.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Conflicts:
block/blk-flush.c
fs/btrfs/check-integrity.c
fs/btrfs/extent_io.c
fs/btrfs/scrub.c
fs/logfs/dev_bdev.c
This is a quick fix for the below two issues when building spdif as modules.
1) If modprobing modules in order: (Step 1) snd-soc-fsl-spdif -> (Step 2)
snd-soc-imx-spdif -> (Step 3) snd-soc-spdif-tx/rx, we will fail to create
imx-spdif card and dai link unless we rmmod snd-soc-imx-spdif and modprobe
it again due to the execution platform_driver_unregister() in probe() when
meeting -EPROBE_DEFER at Step 2.
2) After "imx-spdif sound-spdif.17: dit-hifi <-> 2004000.spdif mapping ok",
'rmmod snd-soc-imx-spdif' would cause kernel dump with warning:
WARNING: CPU: 0 PID: 1301 at /home/rmk/git/linux-rmk/fs/sysfs/dir.c:915 sysfs_hash_and_remove+0x84/0x90()
sysfs: can not remove 'dapm_widget', no directory
This should be caused by disordered resourse releasing of the whole link.
And trying to unregister the card and then CODEC dev can't fix this issue.
Thus this patch just provides a simple fix to these two bugs by using the
snd-soc-dummy in the core instead of seperate snd-soc-spdif-tx/rx so that
there's no need to handle the registering and unregistering of CODEC or
CODEC dai any more.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
From "ASoC: make snd_soc_dai_link more symmetrical", can we see that
the name of CPU DAI maybe omitted. If the DAI name is omitted, try to
use the component name instead.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add new device / subdevice ID for 7265 series.
Fix 2 mistakes on the way.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This patch adds SRC support to Renesas sound driver.
SRC converts sampling rate between codec <-> cpu.
It needs special codec chip,
or very simple DA/AD converter to use it.
This patch was tested via ak4554 codec,
and supports Gen1 only at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas sound has SRC (= Sampling Rate Converter),
but, the HW implementation depends on its generation.
It was part of SRU on Gen1, and SCU on Gen2.
This SCU needs DMA transfer to use it.
Current rsnd driver is using it as DMA transfer buffer
(= no rate convert), and Gen1 is only supported at this point.
This patch cleanup it with focusing about SRC and Gen2 part.
ssi clock which is calculated from rsnd_ssi_master_clk_start()
should have flexibility since Renesas sound has
SRC (= Sampling Rate Converter).
But current implementation is using runtime->rate directly.
This patch tidyup rsnd_ssi_master_clk_start() parameter
as preparation of future SRC support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas sound has SRC (= Sampling Rate Converter),
but, the HW implementation depends on its generation.
It was part of SRU on Gen1, and SCU on Gen2.
This SCU needs DMA transfer to use it.
Current rsnd driver is using it as DMA transfer buffer
(= no rate convert), and Gen1 is only supported at this point.
This patch cleanup it with focusing about SRC and Gen2 part.
rsnd_scu_set_hpbif() is renamed to rsnd_scu_rate_ctrl(),
since its naming doesn't indicate the function meaning.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
INT_ENABLE is needed only Gen2.
rsnd_mod_write() do nothing on Gen1, but it is confusable.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas sound has SRC (= Sampling Rate Converter),
but, the HW implementation depends on its generation.
It was part of SRU on Gen1, and SCU on Gen2.
This SCU needs DMA transfer to use it.
Current rsnd driver is using it as DMA transfer buffer
(= no rate convert), and Gen1 is only supported at this point.
This patch cleanup it with focusing about SRC and Gen2 part.
SRC_CTRL/BUSIF_MODE are used for transfer start.
This patch adds rsnd_scu_transfer_start() and merge these
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas sound has SRC (= Sampling Rate Converter),
but, the HW implementation depends on its generation.
It was part of SRU on Gen1, and SCU on Gen2.
This SCU needs DMA transfer to use it.
Current rsnd driver is using it as DMA transfer buffer
(= no rate convert), and Gen1 is only supported at this point.
This patch cleanup it with focusing about SRC and Gen2 part.
rsnd_scu_set_route() is needed only Gen1.
This patch renames it to rsnd_scu_set_route_if_gen1()
and it adds comment to rsnd_reg member
in order to clarify it is used for Gen1.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver is assuming that
RBGA is used as source clock of 44.1kHz category, and
RBGB is used as source clock of 48kHz category.
This patch clarifies the variable name.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use correct register name which appears in the datasheet
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
we can check rsnd_ssi_init(), not, rsnd_ssi_start()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds rsnd_adg_set_ssi_clk() to access to
AUDIO_CLK_SEL0/1/2, and removes last user of
rsnd_write/read/bset which is very low level function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
