Adjust rx_buf->page_offset when we eat the RX hash prefix. Remove
efx_rx_buf_offset(), which is now redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Currently we prefetch from the Ethernet header, but we will also read
the hash prefix. In practice they should be in the same cache line
and this won't hurt, but it is still pointless to add on the hash
prefix size.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
efx_rx_buf_va() returns the virtual address of the current start of
the buffer. The callers must add the hash prefix size themselves.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The pipeline mechanism will need to change a bit for scattered
packets. Add a wrapper to insulate efx_process_channel() from this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The Linux side of EEH is triggered by MMIO reads, but this
driver's data path does not issue any MMIO reads (except in
legacy interrupt mode). Therefore add a monitor function
to poll EEH periodically.
When preparing to reset the device based on our own error
detection, also poll EEH and defer to its recovery mechanism
if appropriate.
[bwh: Use a separate condition for the initial link poll; fix some
style errors]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
On Siena, VFs share RSS configuration with the PF. We attempted to
support configurations where the PF only uses 1 RX queue and VFs use
multiple RX queues, by (1) setting up RSS for the number of RX queues
per VF (2) disabling RSS in the PF's RX default filters.
Unfortunately commit cd2d5b529c ('sfc: Add SR-IOV back-end support
for SFC9000 family') only included (1). This is (2).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
efx_filter_insert_filter() uses the first table entry in the hash chain
that either has the same match values or is empty. This means that
replacement doesn't always work correctly:
1. Insert filter F1 with match values M1, hashing to H1, at first
possible entry E1.
2. Insert filter F2 with match values M2, hashing to H1, at second
possible entry E2.
3. Remove filter F1.
4. Insert filter F3 with match values M2, hashing to H1, at first
possible entry E1.
F3 should have either replaced F2 or been rejected (depending on
priority and the replace_equal parameter).
Instead, search for both a matching filter that the inserted filter
would replace, and an available insertion point, up to the applicable
maximum search depths. If we insert at lower depth than a replaced
filter, clear the replaced filter.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
efx_filter_search() is only called from efx_filter_insert(), and
neither function is very long. The following bug fix requires a more
sophisticated search with a third result, which is going to be easier
to implement as part of the same function.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
These functions happen to work for default MAC filters: they generate
an initial index of 1/0 for unicast/multicast respectively and an
increment of 1 for either, so a search succeeds at depth 2. But this
is a matter of luck rather than design, and it really won't work well
with the bug fix we're about to do.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The 'for_insert' parameter is redundant since there are no longer
any other operations that need to search based on a filter spec.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The 'replace' flag to efx_filter_insert_filter() controls whether the
new filter may replace *any* filter, and is checked even before
priority comparison. But lower-priority filters should never
block insertion of higher-priority filters.
Change the priority checking so that lower-priority filters are
replaced regardless of the value of the flag, and rename the
flag to 'replace_equal'.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
[bwh: Remove more dead code, and make efx_ptp_rx() pull the data it
needs into the header area.]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
There is a long-standing problem with the packet-timestamp matching in
the driver. When a PTP packet is received by the MC, the FPGA
timestamps the packet and the MC sends the timestamp and 6 bytes of
the UUID to the driver. The driver then matches the timestamp against
received packets using the same 6 bytes of UUID.
The problem comes from the choice of which 6 bytes to use. The PTP
spec is slightly contradictory and misleading in one of the two places
where the UUIDs are discussed. From section 7.2.2.2 of the spec, a
PTPD2 UUID can be either a EUI-64 or a EUI-64 constructed from a
EUI-48. The typical ethernet based implementation uses a EUI-64
constructed from a EUI-48. This works by taking the first 3 bytes of
the MAC address of the NIC being used for PTP (the OUI), then
inserting 0xFF, 0xFE, then taking the last 3 bytes of the MAC address
giving
MAC[0], MAC[1], MAC[2], 0xFF, 0xFE, MAC[3], MAC[4], MAC[5]
The current MC firmware and driver discard the first two bytes of this
UUID and packets are matched against timestamps using bytes 2 to 7 so
there is a small risk that in a deployment of Solarflare PTP NICs used
with other vendors NICs, that a PTP packet could be matched against
the wrong timestamp. This applies to all other organisations whose
third byte of the OUI is 0x53. It's a long list but I notice that it
includes Cisco.
The necessary modifications to use bytes 0-2 and 5-7 of the UUID to
match against are quite small but introduce incompatibility between
older version of the firmware and driver.
When PTP is enabled via SO_TIMESTAMPING specifying PTP V2, the driver
will try to enable PTP in the firmware using the enhanced mode
(above). If the firmware returns an error, the driver will enable PTP
in the firmware using the old mode.
[bwh: Fix some style errors; remove private ioctl bits]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Instead of having efx_ptp_rx() call netif_receive_skb() for an invalid
PTP packet, make it return false for rejected packets and have
efx_rx_deliver() pass them up.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Pablo Neira Ayuso says:
====================
The following patchset contains Netfilter fixes for your net tree,
they are:
* Don't generate audit log message if audit is not enabled, from Gao Feng.
* Fix logging formatting for packets dropped by helpers, by Joe Perches.
* Fix a compilation warning in nfnetlink if CONFIG_PROVE_RCU is not set,
from Paul Bolle.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to e1000e only.
All three patches come from Konstantin Khlebnikov to resolve power
management issues. The first patch removes redundant and unbalanced
pci_disable_device() from the shutdown function. The second patch
removes redundant actions from the driver and fixes the interaction
with actions in pci-bus runtime power management code. The third
and last patch fixes some messages like 'Error reading PHY register'
and 'Hardware Erorr' and saves several seconds on reboot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing address space annotations to all put_guest()/get_guest() callers.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The code can be significantly shortened. There is no functional change,
except that for large (> PAGE_SIZE) copies the guest translation would
be done more frequently.
However, there is not a single user which does this currently. If one
gets added later on this functionality can be added easily again.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The put_guest_u*/get_guest_u* are nothing but wrappers for the regular
put_user/get_user uaccess functions. The only difference is that before
accessing user space the guest address must be translated to a user space
address.
Change the order of arguments for the guest access functions so they
match their uaccess parts. Also remove the u* suffix, so we simply
have put_guest/get_guest which will automatically use the right size
dependent on pointer type of the destination/source that now must be
correct.
In result the same behaviour as put_user/get_user except that accesses
must be aligned.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Let's change to the paradigm that every return code from guest memory
access functions that is not zero translates to -EFAULT and do not
explictly compare.
Explictly comparing the return value with -EFAULT has already shown to
be a bit fragile. In addition this is closer to the handling of
copy_to/from_user functions, which imho is in general a good idea.
Also shorten the return code handling in interrupt.c a bit.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
When out-of-memory the tprot code incorrectly injected a program check
for the guest which reported an addressing exception even if the guest
address was valid.
Let's use the new gmap_translate() which translates a guest address to
a user space address whithout the chance of running into an out-of-memory
situation.
Also make it more explicit that for -EFAULT we won't find a vma.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Implement gmap_translate() function which translates a guest absolute address
to a user space process address without establishing the guest page table
entries.
This is useful for kvm guest address translations where no memory access
is expected to happen soon (e.g. tprot exception handler).
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Guest access functions like copy_to/from_guest() call __guestaddr_to_user()
which in turn call gmap_fault() in order to translate a guest address to a
user space address.
In error case __guest_addr_to_user() returns either -EFAULT or -ENOMEM.
The copy_to/from_guest functions just pass these return values down to the
callers.
The -ENOMEM case however is problematic since there are several places
which access guest memory like:
rc = copy_to_guest(...);
if (rc == -EFAULT)
error_handling();
So in case of -ENOMEM the code assumes that the guest memory access
succeeded even though it failed.
This can cause guest data or state corruption.
If __guestaddr_to_user() returns -ENOMEM the meaning is that a valid user
space mapping exists, but there was not enough memory available when trying
to build the guest mapping. In other words an out-of-memory situation
occured.
For normal user space accesses an out-of-memory situation causes the page
fault handler to map -ENOMEM to -EFAULT (see fixup code in do_no_context()).
We need to do exactly the same for the kvm gaccess functions.
So __guestaddr_to_user() should just map all error codes to -EFAULT.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The logic for calculating the value with which we call kvm_set_cr0/4 was
broken (will definitely be visible with nested unrestricted guest mode
support). Also, we performed the check regarding CR0_ALWAYSON too early
when in guest mode.
What really needs to be done on both CR0 and CR4 is to mask out L1-owned
bits and merge them in from L1's guest_cr0/4. In contrast, arch.cr0/4
and arch.cr0/4_guest_owned_bits contain the mangled L0+L1 state and,
thus, are not suited as input.
For both CRs, we can then apply the check against VMXON_CRx_ALWAYSON and
refuse the update if it fails. To be fully consistent, we implement this
check now also for CR4. For CR4, we move the check into vmx_set_cr4
while we keep it in handle_set_cr0. This is because the CR0 checks for
vmxon vs. guest mode will diverge soon when adding unrestricted guest
mode support.
Finally, we have to set the shadow to the value L2 wanted to write
originally.
Reviewed-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Properly set those bits to 1 that the spec demands in case bit 55 of
VMX_BASIC is 0 - like in our case.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
xfs_bmap.c is a big file, and some of the related code is spread all
throughout the file requiring function prototypes for static
function and jumping all through the file to follow a single call
path. Rearrange the code so that:
a) related functionality is grouped together; and
b) functions are grouped in call dependency order
While the diffstat is large, there are no code changes in the patch;
it is just moving the functionality around and removing the function
prototypes at the top of the file. The resulting layout of the code
is as follows (top of file to bottom):
- miscellaneous helper functions
- extent tree block counting routines
- debug/sanity checking code
- bmap free list manipulation functions
- inode fork format manipulation functions
- internal/external extent tree seach functions
- extent tree manipulation functions used during allocation
- functions used during extent read/allocate/removal
operations (i.e. xfs_bmapi_write, xfs_bmapi_read,
xfs_bunmapi and xfs_getbmap)
This means that following logic paths through the bmapi code is much
simpler - most of the code relevant to a specific operation is now
clustered together rather than spread all over the file....
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Use more preferable function name which implies using a pseudo-random
number generator.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: <bpm@sgi.com>
Cc: Ben Myers <bpm@sgi.com>
Cc: Alex Elder <elder@kernel.org>
Cc: xfs@oss.sgi.com
Signed-off-by: Ben Myers <bpm@sgi.com>
When we read a buffer, we might get an error from the underlying
block device and not the real data. Hence if we get an IO error, we
shouldn't run the verifier but instead just pass the IO error
straight through.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Fix the return type of xfs_iomap_eof_prealloc_initial_size() to
xfs_fsblock_t to reflect the fact that the return value may be an
unsigned 64 bits if XFS_BIG_BLKNOS is defined.
Signed-off-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
The updated speculative preallocation algorithm for handling sparse
files can becomes less effective in situations with a high number of
concurrent, sequential writers. The number of writers and amount of
available RAM affect the writeback bandwidth slicing algorithm,
which in turn affects the block allocation pattern of XFS. For
example, running 32 sequential writers on a system with 32GB RAM,
preallocs become fixed at a value of around 128MB (instead of
steadily increasing to the 8GB maximum as sequential writes
proceed).
Update the speculative prealloc heuristic to base the size of the
next prealloc on double the size of the preceding extent. This
preserves the original aggressive speculative preallocation
behavior and continues to accomodate sparse files at a slight cost
of increasing the size of preallocated data regions following holes
of sparse files.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
If freesp == 0, we could end up in an infinite loop while squashing
the preallocation. Break the loop when we've killed the prealloc
entirely.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
The MIP_ADDRESS state has 2 meanings. If the texture has one sample
per pixel, it's a pointer to the mipmap chain. If the texture has
multiple samples per pixel, it's a pointer to FMASK, a metadata buffer
needed for reading compressed MSAA textures. The mipmap
alignment rules do not apply to FMASK.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The MC is mostly likely busy (e.g., display requests), not hung
so no need to reset it. Doing an MC reset is tricky and not
particularly reliable. Fixes hangs in certain cases.
Reported-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
vbios values are wrong leading to colors that are
too bright. Use the default values instead.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Avoids splatter if the interrupt handler is not registered due
to acceleration being disabled.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable@vger.kernel.org
When the headphone mic jack enum control is created (via explicitly
specification by user), it doesn't make much sense to change the I/O
direction dynamically per capture source change, since the I/O
direction is rather controlled over the enum ctl.
This also reduces the implicit dependency between the capture source
and the hp mic jack enum ctls, which might confuse a program accessing
the whole control elements at once like alsactl.
In addition, this patch introduces update_hp_automute_hook() function
to call the proper hook function. It's just to remove the open codes
in multiple places in hda_generic.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no big merit to distinguish these two hints. Instead, just
have a single flag, add_jack_modes, for creating the jack mode enum
ctls for both I/O directions.
The hint string parser code is left and translated as add_jack_modes
just for keeping compatibility.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The previous commits added the capability to change the pin control of
hp/mic shared jack, but it actually didn't work as expected when the
value is changed from the output to the input, since I forgot to reset
the pin I/O bit in that case. This patch fixes the problem.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In order to let user test the known workaround more easily, give a few
known fixups for ALC260 to the model strings so that it can be passed
via the module option.
Also, move the unusual setups found in FSC S7020 fixup into a special
model, fujitsu-jwse, Jonathan Woithe Special Edition.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a headphone jack is configured as a shared hp/mic jack, the jack
mode enum needs to handle both input and output directions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch improves the generic parser code to allow to set up the
headphone jack as a mic input. User can enable this feature by giving
hp_mic hint string.
The former shared hp/mic feature for the single built-in mic is still
retained. This detection can be disabled now via hp_mic_detect hint
string, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently tick_check_broadcast_device doesn't reject clock_event_devices
with CLOCK_EVT_FEAT_DUMMY, and may select them in preference to real
hardware if they have a higher rating value. In this situation, the
dummy timer is responsible for broadcasting to itself, and the core
clockevents code may attempt to call non-existent callbacks for
programming the dummy, eventually leading to a panic.
This patch makes tick_check_broadcast_device always reject dummy timers,
preventing this problem.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Jon Medhurst (Tixy) <tixy@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Recent GCC versions (e.g. GCC-4.7.2) perform optimizations based on
assumptions about the implementation of memset and similar functions.
The current ARM optimized memset code does not return the value of
its first argument, as is usually expected from standard implementations.
For instance in the following function:
void debug_mutex_lock_common(struct mutex *lock, struct mutex_waiter *waiter)
{
memset(waiter, MUTEX_DEBUG_INIT, sizeof(*waiter));
waiter->magic = waiter;
INIT_LIST_HEAD(&waiter->list);
}
compiled as:
800554d0 <debug_mutex_lock_common>:
800554d0: e92d4008 push {r3, lr}
800554d4: e1a00001 mov r0, r1
800554d8: e3a02010 mov r2, #16 ; 0x10
800554dc: e3a01011 mov r1, #17 ; 0x11
800554e0: eb04426e bl 80165ea0 <memset>
800554e4: e1a03000 mov r3, r0
800554e8: e583000c str r0, [r3, #12]
800554ec: e5830000 str r0, [r3]
800554f0: e5830004 str r0, [r3, #4]
800554f4: e8bd8008 pop {r3, pc}
GCC assumes memset returns the value of pointer 'waiter' in register r0; causing
register/memory corruptions.
This patch fixes the return value of the assembly version of memset.
It adds a 'mov' instruction and merges an additional load+store into
existing load/store instructions.
For ease of review, here is a breakdown of the patch into 4 simple steps:
Step 1
======
Perform the following substitutions:
ip -> r8, then
r0 -> ip,
and insert 'mov ip, r0' as the first statement of the function.
At this point, we have a memset() implementation returning the proper result,
but corrupting r8 on some paths (the ones that were using ip).
Step 2
======
Make sure r8 is saved and restored when (! CALGN(1)+0) == 1:
save r8:
- str lr, [sp, #-4]!
+ stmfd sp!, {r8, lr}
and restore r8 on both exit paths:
- ldmeqfd sp!, {pc} @ Now <64 bytes to go.
+ ldmeqfd sp!, {r8, pc} @ Now <64 bytes to go.
(...)
tst r2, #16
stmneia ip!, {r1, r3, r8, lr}
- ldr lr, [sp], #4
+ ldmfd sp!, {r8, lr}
Step 3
======
Make sure r8 is saved and restored when (! CALGN(1)+0) == 0:
save r8:
- stmfd sp!, {r4-r7, lr}
+ stmfd sp!, {r4-r8, lr}
and restore r8 on both exit paths:
bgt 3b
- ldmeqfd sp!, {r4-r7, pc}
+ ldmeqfd sp!, {r4-r8, pc}
(...)
tst r2, #16
stmneia ip!, {r4-r7}
- ldmfd sp!, {r4-r7, lr}
+ ldmfd sp!, {r4-r8, lr}
Step 4
======
Rewrite register list "r4-r7, r8" as "r4-r8".
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Until we provide the nohz_mask boot parameter, keeping
the context tracking probes disabled by default is pointless
since what we want is to runtime test this code anyway.
It's furthermore confusing for the users which don't expect
the probes to be off when they select RCU user mode or full
dynticks cputime accounting.
Let's enable these probes selftests by default for now.
Suggested: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Mats Liljegren <mats.liljegren@enea.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>