This patch adds basic support for the PF. With this it is possible to
bring up the interface, but without being able to configure any of the
filters on the interface itself.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for the mailbox that connects the PF to the Switch
Management entity. This mailbox will pass TLV formatted messages between
the two entities by using a pair of shared ring buffers.
The primary use of the mailbox is to configure L2 forwarding addresses,
VLANs, and general resource allocation from the switch.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds generic mailbox support. The general idea of the mailboxes
is to use a pair of ring buffers, one for request, one for response to send
data between the local driver and some remote entity be it the PF of the
Switch Manager.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the basic read/write operations for accessing the hardware.
In addition to read read functionality the read functions also provide
surprise remove detection in the event that the device either loses power
or is removed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for the TVL message formats supported by the PF,
VF, and Switch Management entity.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the basic defines and structures needed by the PF for
operation.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the beginning framework onto which I am going to add the
fm10k driver which supports the Intel(R) FM10000 Ethernet Switch Host
Interface.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add device tree binding support for the QCOM ADM DMA driver.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The pinctrl driver initialized the register offsets for the pins
with 0. On Vybrid an offset of 0 is a valid offset for the pinctrl
mux register. So far, this was solved using the ZERO_OFFSET_VALID
flag which allowed offsets of 0. However, this does not allow to
verify whether a pins struct imx_pmx_func was initialized or not.
Use signed offset values for register offsets and initialize those
with -1 in order to detect uninitialized offset values reliable.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This gets rid of the ugly scan structure building
and uses a saner way to do it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make all wmi event functions match the same naming
style, i.e. ath10k_wmi_event_<name>.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make the phyerr structures more compact and easier
to understand. Also add constness.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The logic responsible for processing the event is
no different across different firmware binaries.
The difference that needs to be dealt with is the
ABI of data structures.
The intermediate structure uses __le32 to avoid
extra memory allocations to byteswap
variable-length substructures (i.e. host mem
chunks).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Init functions should be placed at the end of
files in most cases to avoid forward declarations
for static functions.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Simplify the code by deduplicating structure
definitions and code.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The structure is being set up in 2 places.
Deduplicate the code by creating a helper.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This command is not used anymore and most firmware
revisions do not seem to handle it well. Channel
switching is done via vdev restarting.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware reports the number of RF chains so use
that for initialization of supp_{tx,rx}_chainmask
instead of using a macro for 3x3 chips.
This should make tx/rx chainmask reports correct
for chips other than 3x3.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
SCO connection cannot be setup to devices that do not support retransmission.
Patch based on http://permalink.gmane.org/gmane.linux.bluez.kernel/7779 and
adapted for this kernel version.
Code changed to check SCO/eSCO type before setting retransmission effort
and max. latency. The purpose of the patch is to support older devices not
capable of eSCO.
Tested on Blackberry 655+ headset which does not support retransmission.
Credits go to Alexander Sommerhuber.
Signed-off-by: Bernhard Thaler <bernhard.thaler@r-it.at>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some firmware revisions don't wait for beacon tx
completion before sending another SWBA event. This
could lead to hardware using old (freed) beacon
data in some cases, e.g. tx credit starvation
combined with missed TBTT. This is very very rare.
On non-IOMMU-enabled hosts this could be a
possible security issue because hw could beacon
some random data on the air. On IOMMU-enabled
hosts DMAR faults would occur in most cases and
target device would crash.
Since there are no beacon tx completions (implicit
nor explicit) propagated to host the only
workaround for this is to allocate a DMA-coherent
buffer for a lifetime of a vif and use it for all
beacon tx commands. Worst case for this approach
is some beacons may become corrupted, e.g. garbled
IEs or out-of-date TIM bitmap.
Keep the original beacon-related code as-is in
case future firmware revisions solve this problem
so that the old path can be easily re-enabled with
a fw_feature flag.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently, calling intel_fbc_enabled() will trigger a register read.
And we call it a lot of times, even when FBC is disabled, so saving a
few cycles would be a good thing.
Another reason for this patch is because we currently call
intel_fbc_enabled() while the HW is runtime suspended, so the read
makes no sense and triggers a WARN. This happens even if FBC is
disabled by default. Of course one could argue that we just shouldn't
be calling intel_fbc_enabled() while the driver is runtime suspended,
and I agree that's a good argument, but I still think that the reason
explained in the first paragraph already justifies the patch.
This problem can easily be reproduced with many subtests of
igt/pm_rpm, and it is a regression introduced by:
commit c5ad011d7d
Author: Rodrigo Vivi <rodrigo.vivi@intel.com>
Date: Mon Aug 4 03:51:38 2014 -0700
drm/i915: FBC flush nuke for BDW
Testcase: igt/pm_rpm/cursor (and others)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because I plan to expand it a little bit.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since every caller of snd_hda_jack_detect_enable_callback needs to
use the macros from err.h, it makes sense to include it directly
from hda_jack.h.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The same tuning block exists in the dw_mmc h.c and sdhci-msm.c
files. Move these into mmc.c so that they can be shared across
drivers.
Reported-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we're tuning on a big-endian CPU we'll never determine we properly
tuned the device because we compare the data we received from the
controller with a table that assumes the CPU is little-endian.
Change the table to be an array of bytes instead of 32-bit words
so we can use memcmp() without needing to byte-swap every word
depending on the endianess of the CPU.
Cc: Asutosh Das <asutoshd@codeaurora.org>
Cc: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Reviewed-by: Georgi Djakov <gdjakov@mm-sol.com>
Fixes: 415b5a75da "mmc: sdhci-msm: Add platform_execute_tuning implementation"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As soon as the CD IRQ is requested, it can trigger, since it's an
externally controlled event. If it does, delayed_work host->detect will
be scheduled.
Many host controller probe()s are roughly structured as:
*_probe() {
host = sdhci_pltfm_init();
mmc_of_parse(host->mmc);
rc = sdhci_add_host(host);
if (rc) {
sdhci_pltfm_free();
return rc;
}
In 3.17, CD IRQs can are enabled quite early via *_probe() ->
mmc_of_parse() -> mmc_gpio_request_cd() -> mmc_gpiod_request_cd_irq().
Note that in linux-next, mmc_of_parse() calls mmc_gpio*d*_request_cd()
rather than mmc_gpio_request_cd(), and mmc_gpio*d*_request_cd() doesn't
call mmc_gpiod_request_cd_irq(). However, this issue still exists if
mmc_gpio_request_cd() is called directly before mmc_start_host().
sdhci_add_host() may fail part way through (e.g. due to deferred
probe for a vmmc regulator), and sdhci_pltfm_free() does nothing to
unrequest the CD IRQ nor cancel the delayed_work. sdhci_pltfm_free() is
coded to assume that if sdhci_add_host() failed, then the delayed_work
cannot (or should not) have been triggered.
This can lead to the following with CONFIG_DEBUG_OBJECTS_* enabled, when
kfree(host) is eventually called inside sdhci_pltfm_free():
WARNING: CPU: 2 PID: 6 at lib/debugobjects.c:263 debug_print_object+0x8c/0xb4()
ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x18
The object being complained about is host->detect.
There's no need to request the CD IRQ so early; mmc_start_host() already
requests it. For most SDHCI hosts at least, the typical call path that
does this is: *_probe() -> sdhci_add_host() -> mmc_add_host() ->
mmc_start_host(). Therefore, remove the call to mmc_gpiod_request_cd_irq()
from mmc_gpio_request_cd(). This also matches mmc_gpio*d*_request_cd(),
which already doesn't call mmc_gpiod_request_cd_irq().
However, some host controller drivers call mmc_gpio_request_cd() after
mmc_start_host() has already been called, and assume that this will also
call mmc_gpiod_request_cd_irq(). Update those drivers to explicitly call
mmc_gpiod_request_cd_irq() themselves. Ideally, these drivers should be
modified to move their call to mmc_gpio_request_cd() before their call
to mmc_add_host(). However that's too large a change for stable.
This solves the problem (eliminates the kernel error message above),
since it guarantees that the IRQ can't trigger before mmc_start_host()
is called.
The critical point here is that once sdhci_add_host() calls
mmc_add_host() -> mmc_start_host(), sdhci_add_host() is coded not to
fail. In other words, if there's a chance that mmc_start_host() may have
been called, and CD IRQs triggered, and the delayed_work scheduled,
sdhci_add_host() won't fail, and so cleanup is no longer via
sdhci_pltfm_free() (which doesn't free the IRQ or cancel the work queue)
but instead must be via sdhci_remove_host(), which calls mmc_remove_host()
-> mmc_stop_host(), which does free the IRQ and cancel the work queue.
CC: Russell King <linux@arm.linux.org.uk>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix sparse warning introduced by commit 4ef897a ("xfs: flush both
inodes in xfs_swap_extents").
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
xfs_quota.h was included twice.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
This reverts commit 9cb0e39423.
It causes my Sony Vaio Pro 11 to immediately reboot at startup.
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
xfs_dir3_data_get_ftype() gets the file type off disk, but ASSERTs
if it's invalid:
ASSERT(type < XFS_DIR3_FT_MAX);
We shouldn't ASSERT on bad values read from disk. V3 dirs are
CRC-protected, but V2 dirs + ftype are not.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
When running a tight mount/unmount loop on an older kernel, RedHat
QE found that unmount would occasionally hang in
xfs_buf_unpin_wait() on the superblock buffer. Tracing and other
debug work by Eric Sandeen indicated that it was hanging on the
writing of the superblock during unmount immediately after logging
the superblock counters in a synchronous transaction. Further debug
indicated that the synchronous transaction was not waiting for
completion correctly, and we narrowed it down to
xlog_cil_force_lsn() returning NULLCOMMITLSN and hence not pushing
the transaction in the iclog buffer to disk correctly.
While this unmount superblock write code is now very different in
mainline kernels, the xlog_cil_force_lsn() code is identical, and it
was bisected to the backport of commit f876e44 ("xfs: always do log
forces via the workqueue"). This commit made the CIL push
asynchronous for log forces and hence exposed a race condition that
couldn't occur on a synchronous push.
Essentially, the xlog_cil_force_lsn() relied implicitly on the fact
that the sequence push would be complete by the time
xlog_cil_push_now() returned, resulting in the context being pushed
being in the committing list. When it was made asynchronous, it was
recognised that there was a race condition in detecting whether an
asynchronous push has started or not and code was added to handle
it.
Unfortunately, the fix was not quite right and left a race condition
where it it would detect an empty CIL while a push was in progress
before the context had been added to the committing list. This was
incorrectly seen as a "nothing to do" condition and so would tell
xfs_log_force_lsn() that there is nothing to wait for, and hence it
would push the iclogbufs in memory.
The fix is simple, but explaining the logic and the race condition
is a lot more complex. The fix is to add the context to the
committing list before we start emptying the CIL. This allows us to
detect the difference between an empty "do nothing" push and a push
that has not started by adding a discrete "emptying the CIL" state
to avoid the transient, incorrect "empty" condition that the
(unchanged) waiting code was seeing.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
xfs_free_file_space() only affects the range of the file for which space
is being freed. It currently writes and truncates the page cache from
the start offset of the free to EOF.
Modify xfs_free_file_space() to write back and truncate page cache of
just the range being freed.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The collapse range operation currently writes the entire file before
starting the collapse to avoid changes in the in-core extent list due to
writeback causing the extent count to change. Now that collapse range is
fsb based rather than extent index based it can sustain changes in the
extent list during the shift sequence without disruption.
Modify xfs_collapse_file_space() to writeback and invalidate pages
associated with the range of the file to be shifted.
xfs_free_file_space() currently has similar behavior, but the space free
need only affect the region of the file that is freed and this could
change in the future.
Also update the comments to reflect the current implementation. We
retain the eofblocks trim permanently as a best option for dealing with
delalloc extents. We don't shift delalloc extents because this scenario
only occurs with post-eof preallocation (since data must be flushed such
that the cache can be invalidated and data can be shifted). That means
said space must also be initialized before being shifted into the
accessible region of the file only to be immediately truncated off as
the last part of the collapse. In other words, the eofblocks trim will
happen anyways, we just run it first to ensure the file remains in a
consistent state throughout the collapse.
Finally, detect and fail explicitly in the event of a delalloc extent
during the extent shift. The implementation does not support delalloc
extents and the caller is expected to prevent this scenario in advance
as is done by collapse.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
xfs_bmap_shift_extents() has a variety of conditions and error checks
that make the logic difficult to follow and indent heavy. Refactor the
loop body of this function into a new xfs_bmse_shift_one() helper. This
simplifies the error checks, eliminates index decrement on merge hack by
pushing the index increment down into the helper, and makes the code
more readable by reducing multiple levels of indentation.
This is a code refactor only. The behavior of extent shift and collapse
range is not modified.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The extent shift mechanism in xfs_bmap_shift_extents() is complicated
and handles several different, non-deterministic scenarios. These
include extent shifts, extent merges and potential btree updates in
either of the former scenarios.
Refactor the code to be more linear and readable. The loop logic in
xfs_bmap_shift_extents() and some initial error checking is adjusted
slightly. The associated btree lookup and update/delete operations are
condensed into single blocks of code. This reduces the number of
btree-specific blocks and facilitates the separation of the merge
operation into a new xfs_bmse_merge() and xfs_bmse_can_merge() helpers.
This is a code refactor only. The behavior of extent shift and collapse
range is not modified.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The collapse range implementation uses a transaction per extent shift.
The progress of the overall operation is tracked via the current extent
index of the in-core extent list. This is racy because the ilock must be
dropped and reacquired for each transaction according to locking and log
reservation rules. Therefore, writeback to prior regions of the file is
possible and can change the extent count. This changes the extent to
which the current index refers and causes the collapse to fail mid
operation. To avoid this problem, the entire file is currently written
back before the collapse operation starts.
To eliminate the need to flush the entire file, use the file offset
(fsb) to track the progress of the overall extent shift operation rather
than the extent index. Modify xfs_bmap_shift_extents() to
unconditionally convert the start_fsb parameter to an extent index and
return the file offset of the extent where the shift left off, if
further extents exist. The bulk of ths function can remain based on
extent index as ilock is held by the caller. xfs_collapse_file_space()
now uses the fsb output as the starting point for the subsequent shift.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
XFS has been having trouble with stray delayed allocation extents
beyond EOF for a long time. Recent changes to the collapse range
code has triggered erroneous EBUSY errors on page invalidtion for
block size smaller than page size filesystems. These
have been caused by dirty buffers beyond EOF on a partial page which
do not get written to disk during a sync.
The issue is that write-ahead in xfs_cluster_write() finds such a
partial page and handles it by leaving the page dirty but pushing it
into a writeback state. This used to work just fine, as the
write_cache_pages() code would then find the dirty partial page in
the next mapping tree lookup as the dirty tag is still set.
Unfortunately, when we moved to a mark and sweep approach to
writeback to fix other writeback sync issues, we broken this. THe
act of marking the page as under writeback now clears the TOWRITE
tag in the radix tree, even though the page is still dirty. This
causes the TOWRITE tag to be cleared, and hence the next lookup on
the mapping tree does not find the dirty partial page and so doesn't
try to write it again.
This same writeback bug was found recently in ext4 and fixed in
commit 1c8349a ("ext4: fix data integrity sync in ordered mode")
without communication to the wider filesystem community. We can use
exactly the same fix here so the TOWRITE flag is not cleared on
partial page writes.
cc: stable@vger.kernel.org # dependent on 1c8349a171
Root-cause-found-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Today, most callers of ttm_io_prot() check TTM_PL_FLAG_CACHED before
calling it since on some archs it will unconditionally create non-cached
mappings.
But not all callers do which is incorrect as far as I can tell.
Instead, move that check inside ttm_io_port() itself for all archs
and make powerpc use the same implementation as ia64 and arm
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
too some time to narrow down. Although a bit intrusive, this would
be good to get into the -rc cycle as there are quite a few boards
out there with omap3 es2.1 and es3.0, and we have those in at least
three boot test systems too that show errors without this patch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3MaO
-----END PGP SIGNATURE-----
Merge tag 'fix-v3.17-io-chain-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Regression fix for early omap3 revisions for wake-up events that
too some time to narrow down. Although a bit intrusive, this would
be good to get into the -rc cycle as there are quite a few boards
out there with omap3 es2.1 and es3.0, and we have those in at least
three boot test systems too that show errors without this patch.
* tag 'fix-v3.17-io-chain-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: Fix I/O chain clock line assertion timed out error
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix for omap_l3_noc bus code
- Serial console fix for cm-t53
- NAND timings fix for dra7-evm
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NJhf
-----END PGP SIGNATURE-----
Merge tag 'fixes-v3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Few regression fixes for omaps for the -rc cycle:
- Fix for omap_l3_noc bus code
- Serial console fix for cm-t53
- NAND timings fix for dra7-evm
* tag 'fixes-v3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: omap_l3_noc: Fix connID for OMAP4
ARM: dts: cm-t54: fix serial console power supply.
ARM: dts: dra7-evm: Fix NAND GPMC timings
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=s3j+
-----END PGP SIGNATURE-----
Merge tag 'fixes-v3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into fixes
Keystone Edision dts fix for -rc cycle. Fix the PCIE and USB nodes.
* tag 'fixes-v3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: keystone: dts: fix bindings for pcie and usb clock nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 63288b721a ("ARM: imx: fix shared gate clock") attempted to fix
an issue with particular enable/disable sequence from two shared gate
clocks. But unfortunately, while it partially fixed the issue, it also
did something wrong in .is_enabled() function hook. In case of shared
gate, the function shouldn't really query the hardware state via
share_count, because the function is trying to query the enabling state
of the clock in question, not the hardware state which is shared by
multiple clocks.
Fix the issue by returning the enable_count of the clock itself which is
maintained by clock core, in case it's a clock sharing hardware gate
with others. As the result, the initialization of share_count per
hardware state is not needed now. So remove it.
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Fixes: 63288b721a ("ARM: imx: fix shared gate clock")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
What the code does is equivalent to the x86 code, so let's use
it as well
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
pcie_poll_cmd() take msecs instead of jiffies, so convert timeout to msecs.
Fixes: 40b960831c ("PCI: pciehp: Compute timeout from hotplug command start time")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
