Enable sound and modem for the Longcheer L8910 (BQ Aquaris X5).
The setup is similar to most MSM8916 devices, i.e.:
- QDSP6 audio
- Earpiece/headphones/microphones via digital/analog codec in
MSM8916/PM8916
- Audio jack detection via analog codec in PM8916
- WWAN Internet via BAM-DMUX
except:
- Awinic AW8738 connected to HPH_R (headphones) output of the analog
codec. Note that unlike for wingtech-wt88047 there is no analog
switch that would allow disabling output via the headphone jack
when the speaker is enabled.
Signed-off-by: Jonathan Albrieux <jonathan.albrieux@gmail.com>
Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231003-msm8916-modem-v2-11-61b684be55c0@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable sound and modem for the Longcheer L8150 (e.g. Wileyfox Swift).
The setup is similar to most MSM8916 devices, i.e.:
- QDSP6 audio
- Speaker/earpiece/headphones/microphones via digital/analog codec
in MSM8916/PM8916
- Audio jack detection via analog codec in PM8916
- WWAN Internet via BAM-DMUX
except:
- The mpss firmware region must be relocated to a different address.
This is because the wcnss firmware is not relocatable for some
reason. The mpss firmware is too large to avoid overlap with wcnss
when placed at the default address (0x86800000).
Surprisingly the vendor kernel does not handle this. The firmware
regions end up overlapping there and somehow this does not explode.
We try to handle this more safely by relocating the mpss region to
the first higher address that is working correctly: 0x8e800000.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20231003-msm8916-modem-v2-10-61b684be55c0@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable sound and modem for the ASUS Zenfone 2 Laser. The setup is
similar to most MSM8916 devices, i.e.:
- QDSP6 audio
- Speakear/earpiece/headphones/microphones via digital/analog codec
in MSM8916/PM8916
- Audio jack detection via analog codec in PM8916
- WWAN Internet via BAM-DMUX
Signed-off-by: "J.R. Divya Antony" <d.antony.jr@gmail.com>
[Stephan: rebase and simplify, add consistent commit message]
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20231003-msm8916-modem-v2-9-61b684be55c0@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable sound and modem for the Alcatel Idol 3 (4.7"). The setup is
similar to most MSM8916 devices, i.e.:
- QDSP6 audio
- Microphones via digital/analog codec in MSM8916/PM8916
- WWAN Internet via BAM-DMUX
except:
- Stereo NXP TFA9890 codecs for speakers on Quaternary MI2S
- These are also used as earpieces at the top/bottom.
- Asahi Kasei AK4375 headphone codec on Secondary MI2S
-> Primary MI2S is not used for playback
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
[Stephan: Minor refactoring, add consistent commit message]
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20231003-msm8916-modem-v2-8-61b684be55c0@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable sound and modem for the Xiaomi Redmi 2. The setup
is similar to most MSM8916 devices, i.e.:
- QDSP6 audio
- Earpiece/headphones/microphones via digital/analog codec in
MSM8916/PM8916
- Audio jack detection via analog codec in PM8916
- WWAN Internet via BAM-DMUX
except:
- Speaker amplifier is connected to HPH_R (headphones) output of the
analog codec. There is a separate analog switch that allows disabling
playback via the headphone jack.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20231003-msm8916-modem-v2-7-61b684be55c0@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable sound and modem for the Samsung S4 Mini Value Edition. The setup
is similar to most MSM8916 devices, i.e.:
- QDSP6 audio
- Speaker/earpiece/headphones/microphones via digital/analog codec in
MSM8916/PM8916
- WWAN Internet via BAM-DMUX
except:
- Samsung-specific audio jack detection (not supported yet)
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20231003-msm8916-modem-v2-6-61b684be55c0@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable sound and modem for the Samsung A2015 based devices (A3, A5, E5,
E7, Grand Max). The setup is similar to most MSM8916 devices, i.e.:
- QDSP6 audio
- Earpiece/headphones/microphones via digital/analog codec in
MSM8916/PM8916
- WWAN Internet via BAM-DMUX
except:
- NXP TFA9895 codec for speaker on Quaternary MI2S
- Samsung-specific audio jack detection (not supported yet)
[Lin: Add e2015 and grandmax]
Co-developed-by: "Lin, Meng-Bo" <linmengbo0689@protonmail.com>
Signed-off-by: "Lin, Meng-Bo" <linmengbo0689@protonmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20231003-msm8916-modem-v2-5-61b684be55c0@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Most MSM8916/MSM8939 devices use very similar setups for the modem,
because most of the device-specific details are abstracted by the modem
firmware. There are several definitions (status switches, DAI links
etc) that will be exactly the same for every board.
Introduce a common msm8916-modem-qdsp6.dtsi include that can be used to
simplify enabling the modem for such devices. By default the
digital/analog codec in the SoC/PMIC is used, but boards can define
additional codecs by adding additional backend DAI links.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20231003-msm8916-modem-v2-4-61b684be55c0@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
MSM8939 does not have a dedicated ADSP. Instead, the audio services via
APR are also implemented by the modem DSP. Audio can be either routed
via the modem DSP (necessary for voice call audio etc) or directly sent
to the LPASS hardware (currently used by DB410c). Bypassing QDSP6 audio
is only possible with special firmware (on DB410c) or when the modem
DSP is completely disabled.
Add the typical nodes for QDSP6 audio to msm8939.dtsi. The apr node is
disabled by default to avoid changing behavior for devices like
apq8039-t2 that use the bypassed audio path.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20231003-msm8916-modem-v2-3-61b684be55c0@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
MSM8916 does not have a dedicated ADSP. Instead, the audio services via
APR are also implemented by the modem DSP. Audio can be either routed
via the modem DSP (necessary for voice call audio etc) or directly sent
to the LPASS hardware (currently used by DB410c). Bypassing QDSP6 audio
is only possible with special firmware (on DB410c) or when the modem
DSP is completely disabled.
Add the typical nodes for QDSP6 audio to msm8916.dtsi. The apr node is
disabled by default to avoid changing behavior for devices like DB410c
that use the bypassed audio path.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20231003-msm8916-modem-v2-2-61b684be55c0@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
BAM DMUX is used as the network interface to the modem. This is copied
as-is from msm8916.dtsi.
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20231003-msm8916-modem-v2-1-61b684be55c0@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use gpio@ instead of pinctrl@ as that's the name expected by the
qcom,spmi-pmic.yaml schema. Update it to fix dt validation.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231002-pm7250b-gpio-fixup-v2-2-debb8b599989@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the CCI busses found on sc7280 and their pinctrl states.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20231002-sc7280-cci-v2-2-9333fda4612a@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Configure and enable the dual-tone on the PocoPhone F1
Signed-off-by: Joel Selvaraj <joelselvaraj.oss@gmail.com>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231001-b4-sdm845-flash-dts-v1-2-275a3abb0b10@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The DP PHY needs different settings when an eDP display is used.
Make sure these apply on the X13s.
FWIW
I could not notice any user-facing change stemming from this commit.
Fixes: f48c70b111 ("arm64: dts: qcom: sc8280xp-x13s: enable eDP display")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230929-topic-x13s_edpphy-v1-1-ce59f9eb4226@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Fix a couple of instances of incorrectly sorted nodes in the MSM8916
boards. They should be ordered alphabetically for consistency.
No functional change.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20230921-msm8916-rmem-fixups-v1-3-34d2b6e721cf@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable &wcnss_mem for msm8939-longcheer-l9100. This is needed now to
have WCNSS working. It was missed when &wcnss_mem was disabled by
default because the patch with the msm8939-longcheer-l9100 device tree
was not applied yet.
Fixes: 0ece6438a8 ("arm64: dts: qcom: msm8916/39: Disable unneeded firmware reservations")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: André Apitzsch <git@apitzsch.eu>
Tested-by: André Apitzsch <git@apitzsch.eu>
Link: https://lore.kernel.org/r/20230921-msm8916-rmem-fixups-v1-2-34d2b6e721cf@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable the GPU for the msm8916-samsung-gt58 and gt510 tablets now that
they have display panels enabled in the device tree. This was missed
when the GPU was disabled by default because the change was not applied
yet.
Fixes: 0ce5bb825d ("arm64: dts: qcom: msm8916/39: Disable GPU by default")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20230921-msm8916-rmem-fixups-v1-1-34d2b6e721cf@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
While the kernel is booting up, APSS clock / CPU clock will be running
at 800MHz with GPLL0 as source. Once the cpufreq driver is available,
APSS PLL will be configured to the rate based on the opp table and the
source also will be changed to APSS_PLL_EARLY. So allow the mailbox to
consume the GPLL0, with this inclusion, CPU Freq correctly reports that
CPU is running at 800MHz rather than 24MHz.
Signed-off-by: Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230913-gpll_cleanup-v2-11-c8ceb1a37680@quicinc.com
[bjorn: Updated commit message, as requested by Kathiravan]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
While the kernel is booting up, APSS clock / CPU clock will be running
at 800MHz with GPLL0 as source. Once the cpufreq driver is available,
APSS PLL will be configured to the rate based on the opp table and the
source also will be changed to APSS_PLL_EARLY. So allow the mailbox to
consume the GPLL0, with this inclusion, CPU Freq correctly reports that
CPU is running at 800MHz rather than 24MHz.
Signed-off-by: Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230913-gpll_cleanup-v2-10-c8ceb1a37680@quicinc.com
[bjorn: Updated commit message, as requested by Kathiravan]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
While the kernel is booting up, APSS clock / CPU clock will be running
at 800MHz with GPLL0 as source. Once the cpufreq driver is available,
APSS PLL will be configured to the rate based on the opp table and the
source also will be changed to APSS_PLL_EARLY. So allow the mailbox to
consume the GPLL0, with this inclusion, CPU Freq correctly reports that
CPU is running at 800MHz rather than 24MHz.
Signed-off-by: Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230913-gpll_cleanup-v2-9-c8ceb1a37680@quicinc.com
[bjorn: Updated commit message, as requested by Kathiravan]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
While the kernel is booting up, APSS clock / CPU clock will be running
at 800MHz with GPLL0 as source. Once the cpufreq driver is available,
APSS PLL will be configured to the rate based on the opp table and the
source also will be changed to APSS_PLL_EARLY. So allow the mailbox to
consume the GPLL0, with this inclusion, CPU Freq correctly reports that
CPU is running at 800MHz rather than 24MHz.
Signed-off-by: Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230913-gpll_cleanup-v2-8-c8ceb1a37680@quicinc.com
[bjorn: Updated commit message, as requested by Kathiravan]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
IPQ95xx SoCs have different OPPs available for the CPU based on
SoC variant. This can be determined from an eFuse register
present in the silicon.
Add support to read the eFuse and populate the OPPs based on it.
Frequency 1.2GHz 1.8GHz 1.5GHz No opp-supported-hw
Limit
------------------------------------------------------------
936000000 1 1 1 1 0xf
1104000000 1 1 1 1 0xf
1200000000 1 1 1 1 0xf
1416000000 0 1 1 1 0x7
1488000000 0 1 1 1 0x7
1800000000 0 1 0 1 0x5
2208000000 0 0 0 1 0x1
-----------------------------------------------------------
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Link: https://lore.kernel.org/r/14ab08b7cfd904433ca6065fac798d4f221c9d95.1697781921.git.quic_varada@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
IPQ53xx have different OPPs available for the CPU based on
SoC variant. This can be determined through use of an eFuse
register present in the silicon.
Add support to read the eFuse and populate the OPPs based on it.
------------------------------------------------
Frequency BIT2 BIT1 opp-supported-hw
1.1GHz 1.5GHz
------------------------------------------------
1100000000 1 1 0x7
1500000000 0 1 0x3
------------------------------------------------
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Link: https://lore.kernel.org/r/463f01759cedef3121767d2432aa415794036ce1.1697781921.git.quic_varada@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The bindings for the CPU frequency scaling driver require a specific
compatible for the SoC. Add the compatible.
Fixes: 0c665213d1 ("arm64: dts: qcom: sdm670: add cpu frequency scaling")
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230816230412.76862-9-mailingradian@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Follow the example of other platforms and extend the PDC resource region
to 0x30000, so that the PDC driver can read the PDC_VERSION register.
Fixes: 397ad94668 ("arm64: dts: qcom: sm8150: Add pdc interrupt controller node")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230929-topic-sm8x50-upstream-pdc-ver-v5-2-800111572104@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the required BAM and QUP nodes for the QUP1 SPI controller on IPQ5018.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>
Link: https://lore.kernel.org/r/20231004191303.331055-1-robimarko@gmail.com
[bjorn: Padded address to 8 digits, fixed node sort order]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The rb2 only has a single USB controller, it can be switched between a
type-c port and an internal USB hub via a DIP switch. Until dynamic
role switching is available it's preferable to put the USB controller
in host mode so that the type-A ports and ethernet are available.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Fixes: eaa53a8574 ("arm64: dts: qcom: qrb4210-rb2: Enable USB node")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20231010-caleb-rb2-host-mode-v1-1-b057d443cd62@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the USB3+DP Combo QMP PHY port subnodes to facilitate the
description of the connection between the hardware blocks.
Put it in the SoC DTSI to avoid duplication in the device DTs.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20230929-sc7280-qmpphy-ports-v2-1-aae7e9c286b0@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
To make dtbs_check happy and the software more aware of what's going
on, describe the HSUSB PHY's regulators and tighten up VDDA_PLL to match.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20230927-topic-6375_stuff-v1-4-12243e36b45c@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add a dtsi file to include interfaces that are common
across RDPs.
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>
Link: https://lore.kernel.org/r/20230927-common-rdp-v3-1-3d07b3ff6d42@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The sc7280 SoC has a True Random Number Generator, add the node with
the correct compatible set.
Signed-off-by: Om Prakash Singh <quic_omprsing@quicinc.com>
Link: https://lore.kernel.org/r/20231015193901.2344590-5-quic_omprsing@quicinc.com
[bjorn: Padded address to 8 digits, moved hunk to maintain sort order]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The sa8775p SoC has a True Random Number Generator, add the node with
the correct compatible set.
Signed-off-by: Om Prakash Singh <quic_omprsing@quicinc.com>
Link: https://lore.kernel.org/r/20231015193901.2344590-4-quic_omprsing@quicinc.com
[bjorn: Padded address to 8 digits, moved hunk to maintain sort order]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The SM8450 SoC has a True Random Number Generator, add the node with
the correct compatible set.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20231003-topic-sm8550-rng-v4-5-255e4d0ba08e@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the missing regulator supplies to the ADV7533 HDMI bridge to fix
the following dtbs_check warnings. They are all also supplied by
pm8916_l6 so there is no functional difference.
apq8016-sbc.dtb: bridge@39: 'dvdd-supply' is a required property
apq8016-sbc.dtb: bridge@39: 'pvdd-supply' is a required property
apq8016-sbc.dtb: bridge@39: 'a2vdd-supply' is a required property
from schema display/bridge/adi,adv7533.yaml
Fixes: 28546b0955 ("arm64: dts: apq8016-sbc: Add HDMI display support")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230922-db410c-adv7533-regulators-v1-1-68aba71e529b@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Now that the pm7250b.dtsi can be configured to be on a different SID, we
also need to specify it for this dts file. Set it to the SID 2/3 like it
was before commit 8e2d56f645 ("arm64: dts: qcom: pm7250b: make SID
configurable").
Fixes: 8e2d56f645 ("arm64: dts: qcom: pm7250b: make SID configurable")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20230921-pm7250b-sid-fixup-v1-1-231c1a65471f@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Due to the presence of the fastboot micro cable in the CI farm,
it causes the hardware to remain in gadget mode instead of host mode.
So it doesn't find the network, which results in failure to mount root
fs via NFS.
Add an overlay dtso file that sets the dr_mode to host, allowing the
USB controllers to work in host mode. With commit 15d16d6dad
("kbuild: Add generic rule to apply fdtoverlay"), overlay target can
be used to simplify the build of DTB overlays. It uses fdtoverlay to
merge base device tree with the overlay dtso. apq8016-sbc-usb-host.dtb
file can be used by drm-ci, mesa-ci.
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Suggested-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: David Heidelberg <david.heidelberg@collabora.com>
Signed-off-by: Vignesh Raman <vignesh.raman@collabora.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Helen Koike <helen.koike@collabora.com>
Link: https://lore.kernel.org/r/20230911161518.650726-1-vignesh.raman@collabora.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add device tree for the Fairphone 5 smartphone which is based on
the QCM6490 SoC.
Supported features are, as of now:
* Bluetooth
* Debug UART
* Display via simplefb
* Flash/torch LED
* Flip cover sensor
* Power & volume buttons
* RTC
* SD card
* USB
* Various plumbing like regulators, i2c, spi, etc
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230919-fp5-initial-v2-7-14bb7cedadf5@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
