The NOLINK state will poll the phy once a second to see if the link
has come up. If the phy has an interrupt line, this polling can be
skipped, since the phy should interrupt when the link returns.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E1540 can be found embedded in the Marvell 88E6352 switch. It
is compatible with the 88E1510, so add support for it, using the
88E1510 specific functions.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Save and restore FP/LR in BPF prog prologue and epilogue, save SP to FP
in prologue in order to get the correct stack backtrace.
However, ARM64 JIT used FP (x29) as eBPF fp register, FP is subjected to
change during function call so it may cause the BPF prog stack base address
change too.
Use x25 to replace FP as BPF stack base register (fp). Since x25 is callee
saved register, so it will keep intact during function call.
It is initialized in BPF prog prologue when BPF prog is started to run
everytime. Save and restore x25/x26 in BPF prologue and epilogue to keep
them intact for the outside of BPF. Actually, x26 is unnecessary, but SP
requires 16 bytes alignment.
So, the BPF stack layout looks like:
high
original A64_SP => 0:+-----+ BPF prologue
|FP/LR|
current A64_FP => -16:+-----+
| ... | callee saved registers
+-----+
| | x25/x26
BPF fp register => -80:+-----+
| |
| ... | BPF prog stack
| |
| |
current A64_SP => +-----+
| |
| ... | Function call stack
| |
+-----+
low
CC: Zi Shen Lim <zlim.lnx@gmail.com>
CC: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Acked-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset pskb in macvlan_handle_frame in case skb_share_check returned a
clone.
Fixes: 8a4eb5734e ("net: introduce rx_handler results and logic around that")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipvlan_handle_frame is a rx_handler, and when it returns a value other
than RX_HANDLER_CONSUMED (here, NET_RX_DROP aka RX_HANDLER_ANOTHER),
__netif_receive_skb_core expects that the skb still exists and will
process it further, but we just freed it.
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a **skb to ipvlan_rcv_frame so that if skb_share_check returns a
new skb, we actually use it during further processing.
It's safe to ignore the new skb in the ipvlan_xmit_* functions, because
they call ipvlan_rcv_frame with local == true, so that dev_forward_skb
is called and always takes ownership of the skb.
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladislav Yasevich says:
====================
Fix issues with vlans without REORDER_HEADER
A while ago Phil Sutter brought up an issue with vlans without
REORDER_HEADER and bridges. The problem was that if a vlan
without REORDER_HEADER was a port in the bridge, the bridge ended
up forwarding corrupted packets that still contained the vlan header.
The same issue exists for bridge mode macvlan/macvtap devices.
An additional issue with vlans without REORDER_HEADER is that stacking
them also doesn't work. The reason here is that skb_reorder_vlan_header()
function assumes that it on ETH_HLEN bytes deep into the packet. That
is not the case, when you a vlan without REORRDER_HEADER flag set.
This series attempts to correct these 2 issues.
1) To solve the stacked vlans problem, the patch simply use
skb->mac_len as an offset to start copying mac addresses that
is part of header reordering.
2) To fix the issue with bridge/macvlan/macvtap, the second patch
simply doesn't write the vlan header back to the packet if the
vlan device is either a bridge or a macvlan port. This ends up
being the simplest and least performance intrussive solution.
I've considered extending patch 2 to all stacked devices (essentially
checked for the presense of rx_handler), but that feels like a broader
restriction and _may_ break existing uses.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a vlan is configured with REORDER_HEADER set to 0, the vlan
header is put back into the packet and makes it appear that
the vlan header is still there even after it's been processed.
This posses a problem for bridge and macvlan ports. The packets
passed to those device may be forwarded and at the time of the
forward, vlan headers end up being unexpectedly present.
With the patch, we make sure that we do not put the vlan header
back (when REORDER_HEADER is 0) if a bridge or macvlan has
been configured on top of the vlan device.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we have multiple stacked vlan devices all of which have
turned off REORDER_HEADER flag, the untag operation does not
locate the ethernet addresses correctly for nested vlans.
The reason is that in case of REORDER_HEADER flag being off,
the outer vlan headers are put back and the mac_len is adjusted
to account for the presense of the header. Then, the subsequent
untag operation, for the next level vlan, always use VLAN_ETH_HLEN
to locate the begining of the ethernet header and that ends up
being a multiple of 4 bytes short of the actuall beginning
of the mac header (the multiple depending on the how many vlan
encapsulations ethere are).
As a reslult, if there are multiple levles of vlan devices
with REODER_HEADER being off, the recevied packets end up
being dropped.
To solve this, we use skb->mac_len as the offset. The value
is always set on receive path and starts out as a ETH_HLEN.
The value is also updated when the vlan header manupations occur
so we know it will be correct.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default the driver allowed incorrect frames to be received. What is
worse the code does not handle very short frames correctly. The FCS
length is unconditionally subtracted, and the underflow can cause
skb_put to be called with large number after implicit cast to unsigned.
And indeed, an skb_over_panic() was observed with via-velocity.
This removes the module parameter as it does not work in it's
current state, and should be implemented via NETIF_F_RXALL if needed.
Suggested-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new SoC specific binding for rcar-dmac and the generic
binding as a fall-back in the r8a7794 device tree.
In general Renesas hardware is not documented to the extent where the
relationship between IP blocks on different SoCs can be assumed although
they may appear to operate the same way. Furthermore the documentation
typically does not specify a version for individual IP blocks. For these
reasons a convention of using the SoC name in place of a version and
providing SoC-specific compat strings has been adopted.
Although not universally liked this convention is used in the bindings for
most drivers for Renesas hardware. The purpose of this patch is to
update the Renesas R-Car DMA Controller nodes to follow this convention.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the new SoC specific binding for rcar-dmac and the generic
binding as a fall-back in the r8a7793 device tree.
In general Renesas hardware is not documented to the extent where the
relationship between IP blocks on different SoCs can be assumed although
they may appear to operate the same way. Furthermore the documentation
typically does not specify a version for individual IP blocks. For these
reasons a convention of using the SoC name in place of a version and
providing SoC-specific compat strings has been adopted.
Although not universally liked this convention is used in the bindings for
most drivers for Renesas hardware. The purpose of this patch is to
update the Renesas R-Car DMA Controller nodes to follow this convention.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the new SoC specific binding for rcar-dmac and the generic
binding as a fall-back in the r8a7791 device tree.
In general Renesas hardware is not documented to the extent where the
relationship between IP blocks on different SoCs can be assumed although
they may appear to operate the same way. Furthermore the documentation
typically does not specify a version for individual IP blocks. For these
reasons a convention of using the SoC name in place of a version and
providing SoC-specific compat strings has been adopted.
Although not universally liked this convention is used in the bindings for
most drivers for Renesas hardware. The purpose of this patch is to
update the Renesas R-Car DMA Controller nodes to follow this convention.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the new SoC specific binding for rcar-dmac and the generic
binding as a fall-back in the r8a7790 device tree.
In general Renesas hardware is not documented to the extent where the
relationship between IP blocks on different SoCs can be assumed although
they may appear to operate the same way. Furthermore the documentation
typically does not specify a version for individual IP blocks. For these
reasons a convention of using the SoC name in place of a version and
providing SoC-specific compat strings has been adopted.
Although not universally liked this convention is used in the bindings for
most drivers for Renesas hardware. The purpose of this patch is to
update the Renesas R-Car DMA Controller nodes to follow this convention.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
In multipath_prepare_ioctl(),
- pgpath is a path selected from available paths
- m->queue_io is true if we cannot send a request immediately to
paths, either because:
* there is no available path
* the path group needs activation (pg_init)
- pg_init is not started
- pg_init is still running
- m->queue_if_no_path is true if the device is configured to queue
I/O if there are no available paths
If !pgpath && !m->queue_if_no_path, the handler should return -EIO.
However in the course of refactoring the condition check has broken
and returns success in that case. Since bdev points to the dm device
itself, dm_blk_ioctl() calls __blk_dev_driver_ioctl() for itself and
recurses until crash.
You could reproduce the problem like this:
# dmsetup create mp --table '0 1024 multipath 0 0 0 0'
# sg_inq /dev/mapper/mp
<crash>
[ 172.648615] BUG: unable to handle kernel paging request at fffffffc81b10268
[ 172.662843] PGD 19dd067 PUD 0
[ 172.666269] Thread overran stack, or stack corrupted
[ 172.671808] Oops: 0000 [#1] SMP
...
Fix the condition check with some clarifications.
Fixes: e56f81e0b0 ("dm: refactor ioctl handling")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
(Ab)using the @bdev passed to dm_blk_ioctl() opens the potential for
targets' .prepare_ioctl to fail if they go on to check the bdev for
!NULL.
Fixes: e56f81e0b0 ("dm: refactor ioctl handling")
Reported-by: Junichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add r8a7793 GPIO device nodes that are assumed to be identical
to r8a7791. This matches the data sheet for GPIO and MSTP bits.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
dm-mpath retries ioctl, when no path is readily available and the device
is configured to queue I/O in such a case. If you want to stop the retry
before multipathd decides to turn off queueing mode, you could send
signal for the process to exit from the loop.
However the check of fatal signal has not carried along when commit
6c182cd88d ("dm mpath: fix ioctl deadlock when no paths") moved the
loop from dm-mpath to dm core. As a result, we can't terminate such
a process in the retry loop.
Easy reproducer of the situation is:
# dmsetup create mp --table '0 1024 multipath 0 0 0 0'
# dmsetup message mp 0 'queue_if_no_path'
# sg_inq /dev/mapper/mp
then you should be able to terminate sg_inq by pressing Ctrl+C.
Fixes: 6c182cd88d ("dm mpath: fix ioctl deadlock when no paths")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Handle DC off as a power well where enabling the power well will prevent
the DMC to enter selected DC states (required around modesets and Aux
A). Disabling the power well will allow DC states again. For now the
highest DC state is DC6 for Skylake and DC5 for Broxton but will be
configurable for Skylake in a later patch.
v2: Check both DC5 and DC6 bits in power well enabled function (Ville)
v3:
- Remove unneeded DC_OFF case in skl_set_power_well() (Imre)
- Add PW2 dependency to DC_OFF (Imre)
v4: Put DC_OFF before PW2 in BXT power well array
Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[fixed line over 80 and parenthesis alignment checkpatch warns (imre)]
Link: http://patchwork.freedesktop.org/patch/msgid/1447687201-24759-1-git-send-email-patrik.jakobsson@linux.intel.com
PG2 enabled is not a requirement for disabling DC5. It's just one
of the reasons why the DMC wouldn't enter DC5. During modeset we don't
care about PG2 from a DC perspective, only the fact that DC5/DC6 is not
allowed.
Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447084107-8521-9-git-send-email-patrik.jakobsson@linux.intel.com
All the DDI power domains are already excluded from
SKL_DISPLAY_ALWAYS_ON_POWER_DOMAINS on account of
excluding SKL_DISPLAY_POWERWELL_1_POWER_DOMAINS and
SKL_DISPLAY_POWERWELL_2_POWER_DOMAINS, no need to spell them out again.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447084107-8521-6-git-send-email-patrik.jakobsson@linux.intel.com
Currently the gmbus code uses intel_aux_display_runtime_get/put in an
effort to make sure the hardware is powered up sufficiently for gmbus.
That function only takes the runtime PM reference which on VLV/CHV/BXT
is not enough. We need the disp2d/pipe-a well on VLV/CHV and power well
2 on BXT. So add a new power domnain for gmbus and kill off the now
unused intel_aux_display_runtime_get/put. And change
intel_hdmi_set_edid() to use the gmbus power domain too since that's all
we need there.
Also toss in a BUILD_BUG_ON() to catch problems if we run out of
bits for power domains. We're already really close to the limit...
[Patrik: Add gmbus string to debugfs output]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447084107-8521-5-git-send-email-patrik.jakobsson@linux.intel.com
Introduce intel_display_port_aux_power_domain() which simply returns
the appropriate AUX power domain for a specific port, and then replace
the intel_display_port_power_domain() with calls to the new function
in the DP code. As long as we're not actually enabling the port we don't
need the lane power domains, and those are handled now purely from
modeset_update_crtc_power_domains().
My initial motivation for this was to see if I could keep the DPIO power
wells powered down while doing AUX on CHV, but turns out I can't so this
doesn't change anything for CHV at least. But I think it's still a
worthwile change.
v2: Add case for PORT E. Default to POWER_DOMAIN_AUX_D for now. (Ville)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447682467-6237-1-git-send-email-patrik.jakobsson@linux.intel.com
Replaces "drm/i915: Force loading of csr program at boot" in the old
series.
Previously we called blindly into intel_csr_load_program() and depended
on a check of whether the CSR program memory was cleared or not.
This check is not reliable and no longer needed since we fixed the
call-sites of intel_csr_load_program().
Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447084107-8521-2-git-send-email-patrik.jakobsson@linux.intel.com
When this option is 0 (so the power well support is disabled) we are
supposed to enable all power wells once and don't disable them unless we
system suspend the device. Currently if the option is 0, we can call the
power well enable handlers multiple times, whenever their refcount
changes from 0->1. This may not be a problem for the HW, but it's not
logical and may trigger some warnings in the power well code which
doesn't expect this. So simply keep around a reference while we are
not system suspended to solve this. For simplicity mark the module
option read only, so we don't need to deal with re-enabling the feature
during runtime. If someone really needs that it could be added later in
a more proper way.
v2:
- fix typo in comment in intel_power_domains_suspend() (Patrik)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447775063-24438-1-git-send-email-imre.deak@intel.com
We don't need to reinit DDI and IRQs during PW1 enabling any more, since
we don't toggle PW1 on-demand any more. We enable PW1 only as part of
the display core init sequence and after this we initialize both DDI and
IRQs later in the init sequence. So remove these init steps from the
power well code.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-11-git-send-email-imre.deak@intel.com
Suppressing LCPLL disabling was added to avoid interfering with the DMC
firmware. It is not needed any more since we uninit CDCLK now with the
DMC deactivated (DC states disabled). We also must disable it during system
suspend as part of the Bspec "Display uninit sequence".
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-10-git-send-email-imre.deak@intel.com
We need to disable the DC states during display core init to sanitize
the HW state we inherit from the BIOS. We need to disable it during
display core uninit too, since the power well framework will leave it
enabled (since we get to the display core uninit step with all power
domains disabled already).
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-9-git-send-email-imre.deak@intel.com
With the DMC firmware installed we don't need to handle HW resources
that are handled automatically by the firmware. Besides being redundant
this can also interfere with the firmware, possibly getting it into a
broken/blocked state. The on-demand handling of PW1 was already half-way
removed, MISC IO was still handled in this way. After the last patch we
init/uninit these HW resources manually as part of the display core
init/uninit sequence, so we can now remove the on-demand handling for
these completely.
We still keep around the power wells (with no domains attached to them)
since the manual toggling during display core init/uninit happens via
the current API.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
[s/beeing/being/ in commit message (imre)]
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-7-git-send-email-imre.deak@intel.com
We need to initialize the display core part early, before initializing
the rest of the display power state. This is also described in the bspec
termed "Display initialization sequence". Atm we run this sequence
during driver loading after power domain HW state initialization which
is too late and during runtime suspend/resume which is unneeded and can
interere with DMC functionality which handles HW resources toggled
by this init/uninit sequence automatically. The init sequence must be
run as the first step of HW power state initialization and during
system resume. The uninit sequence must be run during system suspend.
To address the above move the init sequence to the initial HW power
state setup and the uninit sequence to a new power domains suspend
function called during system suspend.
As part of the init sequence we also have to reprogram the DMC firmware
as it's lost across a system suspend/resume cycle.
After this change CD clock initialization during driver loading will
happen only later after other dependent HW/SW parts are initialized,
while during system resume it will get initialized as the last step of
the init sequence. This distinction can be removed by some refactoring
of platform independent parts. I left this refactoring out from this
series since I didn't want to change non-SKL parts. This is a TODO for
later.
v2:
- fix error path in i915_drm_suspend_late()
- don't try to re-program the DMC firmware if it failed to load
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447774433-20834-1-git-send-email-imre.deak@intel.com
22M/24M clocks are only required for I2S, so move the control to
I2S DAI ops.
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make it possible to use the bulk API with optional supplies, by allowing
the consumer to marking supplies as optional in the regulator_bulk_data.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For SAI master mode, when Tx(Rx) sync with Rx(Tx) clock, Rx(Tx) will
generate bclk and frame clock for Tx(Rx), we should set RCR4(TCR4),
RCR5(TCR5) and RMR(TMR) for playback(capture), or there will be sync
error sometimes.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In fsl_sai_set_bclk function, we should not set bclk for Tx/Rx Synchronous
with another SAI mode.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Before this patch, we used the intel_display_power_{get,put} functions
to make sure the PW1 and Misc I/O power wells were enabled all the
time while LCPLL was enabled. We called a get() at
intel_ddi_pll_init() when we discovered that LCPLL was enabled, then
we would call put/get at skl_{un,}init_cdclk().
The problem is that skl_uninit_cdclk() is indirectly called by
intel_runtime_suspend(). So it will only release its power well
_after_ we already decided to runtime suspend. But since we only
decide to runtime suspend after all power wells and refcounts are
released, that basically means we will never decide to runtime
suspend.
So what this patch does to fix that problem is move the PW1 + Misc I/O
power well handling out of the runtime PM mechanism: instead of
calling intel_display_power_{get_put} - functions that touch the
refcount -, we'll call the low level intel_power_well_{en,dis}able,
which don't change the refcount. This way, it is now possible for the
refcount to actually reach zero, and we'll now start runtime
suspending/resuming.
v2 (from Paulo):
- Write a commit message since the original patch left it empty.
- Rebase after the intel_power_well_{en,dis}able rename.
- Use lookup_power_well() instead of hardcoded indexes.
Testcase: igt/pm_rpm/rte (and every other rpm test)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92211
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92605
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-4-git-send-email-imre.deak@intel.com
Doing a bit-or operation with zero is pointless.
Remove this unneeded bit-or.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Enable the DU device and the VGA port available on the r8a7794
ALT board. The VGA portion of the ALT board is somewhat similar
to the Lager board but in case of ALT the DU1 pins are used
and the X2 clock has a reduced frequency.
This patch does not include any pinctrl (PFC) settings due to lack
of PFC DT integration on r8a7794. At this point the default state
of the boot loader is enough to keep the VGA port working without
changing any pinctrl settings.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the DU device with a disabled state. Boards that want to enable the
DU need to specify the output topology.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU0 clock is an MSTP clock, child of the CPG ZX clock.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pull vfs fixes from Al Viro:
"A fs-cache regression fix, and adding a warning about obnoxiou^W
moderation of list given in MAINTAINERS"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
MAINTAINERS: linux-cachefs@redhat.com is moderated for non-subscribers
FS-Cache: Add missing initialization of ret in cachefiles_write_page()
parkbd_parport_cb is a local uninitialized structure and the member
function pointers will be pointing to arbitrary locations unless they
are cleared.
Fixes: 33ca8ab97c ("Input: parkbd - use parallel port device model")
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
walkera0701_parport_cb is a local uninitialized structure and the member
function pointers will be pointing to arbitrary locations unless they
are cleared.
Fixes: 221bcb24c6 ("Input: walkera0701 - use parallel port device model")
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
