This change converts the probe hook to register the IIO device with
devm_iio_device_register() and register a hook with
devm_add_action_or_reset() to put the device in powerdown when the driver
gets unloaded.
Since the PM suspend/resume functions need only a reference to the
i2c_client object (which can be obtained from the base device object), the
i2c_set_clientdata() call can be removed.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210630131636.1563148-2-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These 2 functions only do I2C reads/writes and don't require any of the
private data of the driver.
They're also used in the PM suspend/resume part of the driver.
Converting them to take an i2c_client object as parameter simplifies things
a bit (especially in the suspend/resume) as the driver mostly needs the
reference for i2c_client, so no need to jump through hoops to get it from
the private data (as was done in many places).
The rfd77402_measure() function has also been converted to take an
i2c_client object, since it also does only I2C ops.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210630131636.1563148-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Now that the driver's buffer is stored on the adjd_s311_data private
object, the driver is a simple conversion to use only device-managed
functions in the probe.
The iio_triggered_buffer_setup() and iio_device_register() functions are
the only ones needing conversion.
And i2c_set_clientdata() is no longer required.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210705071456.649659-2-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change moves the entire buffer on the private adjd_s311_data type.
Since the device has 4 channels, it's not a big waste to just allocate the
maximum possible buffer and use only what's needed.
This is in contrast with free-ing and re-allocating the buffer on the
update_scan_mode hook.
Since the driver pushes buffer data with
iio_push_to_buffers_with_timestamp(), the buffer must also include a
64-bit buffer for the timestamp, for each sample-set.
With this change, the adjd_s311_update_scan_mode() is no longer needed.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210705071456.649659-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Set reset pin direction to output as the reset pin needs to be an active
low output pin.
Co-developed-by: Hannu Hartikainen <hannu@hrtk.in>
Signed-off-by: Hannu Hartikainen <hannu@hrtk.in>
Signed-off-by: Antti Keränen <detegr@rbx.email>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Fixes: ecb010d441 ("iio: imu: adis: Refactor adis_initial_startup")
Link: https://lore.kernel.org/r/20210708095425.13295-1-detegr@rbx.email
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADS7950 requires that CS is deasserted after each SPI word. Before
commit e2540da86e ("iio: adc: ti-ads7950: use SPI_CS_WORD to reduce
CPU usage") the driver used a message with one spi transfer per channel
where each but the last one had .cs_change set to enforce a CS toggle.
This was wrongly translated into a message with a single transfer and
.cs_change set which results in a CS toggle after each word but the
last which corrupts the first adc conversion of all readouts after the
first readout.
Fixes: e2540da86e ("iio: adc: ti-ads7950: use SPI_CS_WORD to reduce CPU usage")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: David Lechner <david@lechnology.com>
Tested-by: David Lechner <david@lechnology.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210709101110.1814294-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It is similar to other devices, but with 8 channels.
Signed-off-by: Simon Xue <xxm@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20210712014507.97477-1-xxm@rock-chips.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is more standard to have sanity checks at the entry of a function,
instead of allocating some memory first and having to free it if a
condition is not met.
Shuffle code a bit to check 'masklength' before calling 'bitmap_alloc()'
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/98a351adda1908c306e981b9cc86d3dbc79eb5ec.1626261211.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix 2 possible memleaks on error-exits from tlmi_analyze():
1. If the kzalloc of pwd_power fails, then not only free the atributes,
but also the allocated pwd_admin struct.
2. Freeing the attributes should also free the possible_values strings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210717143607.3580-3-hdegoede@redhat.com
tlmi_sysfs_init() calls tlmi_release_attr() on errors which calls
kobject_put() for attributes created by tlmi_analyze(), but if we
bail early because of an error, then this means that some of the
kobjects will not have been initialized yet; and we should thus not
call kobject_put() on them.
Switch from using kobject_init_and_add() inside tlmi_sysfs_init() to
initializing all the created kobjects directly in tlmi_analyze() and
only adding them from tlmi_sysfs_init(). This way all kobjects will
always be initialized when tlmi_release_attr() gets called.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210717143607.3580-2-hdegoede@redhat.com
Move the pending_reboot node under attributes dir where it should live, as
documented in: Documentation/ABI/testing/sysfs-class-firmware-attributes.
Also move the create / remove code to be together with the other code
populating / cleaning the attributes sysfs dir. In the removal path this
is necessary so that the remove is done before the
kset_unregister(tlmi_priv.attribute_kset) call.
Signed-off-by: Mark Pearson <markpearson@lenovo.com>
Co-developed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210717143607.3580-1-hdegoede@redhat.com
This adds a driver for panels based on the WideChips WS2401 display
controller. This display controller is used in the Samsung LMS380KF01
display found in the Samsung GT-I8160 (Codina) mobile phone and
possibly others.
As is common with Samsung displays manufacturer commands are necessary
to configure the display to a working state.
The display optionally supports internal backlight control, but can
also use an external backlight.
This driver re-uses the DBI infrastructure to communicate with the
display.
Cc: phone-devel@vger.kernel.org
Cc: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210714225002.1065107-2-linus.walleij@linaro.org
It was reported that on i386 config
------
on i386:
ld: drivers/platform/x86/amd-pmc.o: in function `s0ix_stats_show':
amd-pmc.c:(.text+0x100): undefined reference to `__udivdi3'
-------
The reason for this is that 64-bit integer division is not supported
on 32-bit architecture. Use do_div macro to fix this.
Fixes: b9a4fa6978 ("platform/x86: amd-pmc: Add support for logging s0ix counters")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org> # and build-tested
Link: https://lore.kernel.org/r/20210716153802.2929670-1-Shyam-sundar.S-k@amd.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
SB16 CSP driver may hit potentially a typical ABBA deadlock in two
code paths:
In snd_sb_csp_stop():
spin_lock_irqsave(&p->chip->mixer_lock, flags);
spin_lock(&p->chip->reg_lock);
In snd_sb_csp_load():
spin_lock_irqsave(&p->chip->reg_lock, flags);
spin_lock(&p->chip->mixer_lock);
Also the similar pattern is seen in snd_sb_csp_start().
Although the practical impact is very small (those states aren't
triggered in the same running state and this happens only on a real
hardware, decades old ISA sound boards -- which must be very difficult
to find nowadays), it's a real scenario and has to be fixed.
This patch addresses those deadlocks by splitting the locks in
snd_sb_csp_start() and snd_sb_csp_stop() for avoiding the nested
locks.
Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/7b0fcdaf-cd4f-4728-2eae-48c151a92e10@gmail.com
Link: https://lore.kernel.org/r/20210716132723.13216-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixes coccicheck warnings:
./drivers/firmware/qcom_scm.c:324:20-22:
WARNING !A || A && B is equivalent to !A || B
Signed-off-by: Junlin Yang <yangjunlin@yulong.com>
Link: https://lore.kernel.org/r/20210311013235.1458-1-angkery@163.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Mark the qcom_scm_convention_names[] array const as it isn't changed.
Cc: Elliot Berman <eberman@codeaurora.org>
Fixes: 9a434cee77 ("firmware: qcom_scm: Dynamically support SMCCC and legacy conventions")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210222031431.3831189-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
vcpu_put is not called if the user copy fails. This can result in preempt
notifier corruption and crashes, among other issues.
Fixes: b3cebfe8c1 ("KVM: PPC: Move vcpu_load/vcpu_put down to each ioctl case in kvm_arch_vcpu_ioctl")
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210716024310.164448-2-npiggin@gmail.com
When running CPU_FTR_P9_TM_HV_ASSIST, HFSCR[TM] is set for the guest
even if the host has CONFIG_TRANSACTIONAL_MEM=n, which causes it to be
unprepared to handle guest exits while transactional.
Normal guests don't have a problem because the HTM capability will not
be advertised, but a rogue or buggy one could crash the host.
Fixes: 4bb3c7a020 ("KVM: PPC: Book3S HV: Work around transactional memory bugs in POWER9")
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210716024310.164448-1-npiggin@gmail.com
- Drop 'resets' as required on renesas,du
- Moving of fixed string patterns for 'properties' instead of
'patternProperties'
- Drop more redundant minItems/maxItems that we merged in the merge
window
- Indentation warning fix for sja1105
-----BEGIN PGP SIGNATURE-----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=EiRx
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Drop 'resets' as required on renesas,du
- Moving of fixed string patterns for 'properties' instead of
'patternProperties'
- Drop more redundant minItems/maxItems that we merged in the merge
window
- Indentation warning fix for sja1105
* tag 'devicetree-fixes-for-5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: display: renesas,du: Make resets optional on R-Car H1
dt-bindings: Move fixed string 'patternProperties' to 'properties'
dt-bindings: More dropping redundant minItems/maxItems
dt-bindings: net: dsa: sja1105: Fix indentation warnings
- Fix instrumentation annotations for entry code
- Ensure kernel MTE state is restored correctly on resume from suspend
- Fix MTE fault from new strlen() routine
- Fallback to byte-wise accesses on initial uaccess fault
- Bump Clang requirement for BTI
- Revert ARCH_DMA_MINALIGN back to 128 bytes (shakes fist at Qualcomm)
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAmDxWmcQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjND/yCACldN5Vq22ukGC+XP1XEk5XgYlepr47nwZG
x52B24Id9WHWf8Hw9C7N0TaaxJCSQ/mJ265g8GqudZ9y5BrQLjfM/YXBCt4G1y1a
5jKrAO1XUqldiO2raniitrLL7aXehjXgC6eJwKtswcWA5FDPghCH6bZmitCQC9bQ
7GD5wxoeTF6m00ykNznqxXLFAjWnAY6nHHpFZ1Af/qMqwgOifJ+FXN11C7Un6r1G
it/XHHounn736EsIDQzyHFdl1j52dlKtstmQ39TUUeHGum7PR8AyKc/J0MS92qB7
njYuRedc5adK1RRzG/MrB1HJqY5qpWzpVbpeAVuWmMTh6Kmt37sz
=+zaG
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The bulk of the diffstat consists of changes to our uaccess routines
so that they fall back to bytewise copying prior to reporting complete
failure when the initial (multi-byte) access faults.
However, the most disappointing change here is that we've had to bump
ARCH_DMA_MINALIGN back to 128 bytes thanks to Qualcomm's "Kryo" CPU,
which ended up in the MSM8996 mobile SoC. Still, at least we're now
aware of this design and one of the hardware designers confirmed the
L2 cacheline size for us.
Summary:
- Fix instrumentation annotations for entry code
- Ensure kernel MTE state is restored correctly on resume from suspend
- Fix MTE fault from new strlen() routine
- Fallback to byte-wise accesses on initial uaccess fault
- Bump Clang requirement for BTI
- Revert ARCH_DMA_MINALIGN back to 128 bytes (shakes fist at Qualcomm)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: entry: fix KCOV suppression
arm64: entry: add missing noinstr
arm64: mte: fix restoration of GCR_EL1 from suspend
arm64: Avoid premature usercopy failure
arm64: Restrict ARM64_BTI_KERNEL to clang 12.0.0 and newer
Revert "arm64: cache: Lower ARCH_DMA_MINALIGN to 64 (L1_CACHE_BYTES)"
arm64: Add missing header <asm/smp.h> in two files
arm64: fix strlen() with CONFIG_KASAN_HW_TAGS
Ronak Doshi says:
====================
vmxnet3: upgrade to version 6
vmxnet3 emulation has recently added several new features which includes
increase in queues supported, remove power of 2 limitation on queues,
add RSS for ESP IPv6, etc. This patch series extends the vmxnet3 driver
to leverage these new features.
Compatibility is maintained using existing vmxnet3 versioning mechanism as
follows:
- new features added to vmxnet3 emulation are associated with new vmxnet3
version viz. vmxnet3 version 6.
- emulation advertises all the versions it supports to the driver.
- during initialization, vmxnet3 driver picks the highest version number
supported by both the emulation and the driver and configures emulation
to run at that version.
In particular, following changes are introduced:
Patch 1:
This patch introduces utility macros for vmxnet3 version 6 comparison
and updates Copyright information.
Patch 2:
This patch adds support to increase maximum Tx/Rx queues from 8 to 32.
Patch 3:
This patch removes the limitation of power of 2 on the queues.
Patch 4:
Uses existing get_rss_hash_opts and set_rss_hash_opts methods to add
support for ESP IPv6 RSS.
Patch 5:
This patch reports correct RSS hash type based on the type of RSS
performed.
Patch 6:
This patch updates maximum configurable mtu to 9190.
Patch 7:
With all vmxnet3 version 6 changes incorporated in the vmxnet3 driver,
with this patch, the driver can configure emulation to run at vmxnet3
version 6.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With all vmxnet3 version 6 changes incorporated in the vmxnet3 driver,
the driver can configure emulation to run at vmxnet3 version 6, provided
the emulation advertises support for version 6.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch increases the maximum configurable mtu to 9190
to accommodate jumbo packets of overlay traffic.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As vmxnet3 supports IP/TCP/UDP RSS, this patch sets appropriate
hash type based on the type of RSS performed.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vmxnet3 version 4 added support for ESP RSS. However, only IPv4 was
supported. With vmxnet3 version 6, this patch enables RSS for ESP
IPv6 packets as well.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With version 6, vmxnet3 relaxes the restriction on queues to
be power of two. This is helpful in cases (Edge VM) where
vcpus are less than 8 and device requires more than 4 queues.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, vmxnet3 supports maximum of 8 Tx/Rx queues. With increase
in number of vcpus on a VM, to achieve better performance and utilize
idle vcpus, we need to increase the max number of queues supported.
This patch enhances vmxnet3 to support maximum of 32 Tx/Rx queues.
Increasing the Rx queues also increases the probability of distrubuting
the traffic from different flows to different queues with RSS.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3 is currently at version 4 and this patch initiates the
preparation to accommodate changes for upto version 6. Introduced
utility macros for vmxnet3 version 6 comparison and update Copyright
information.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alan Maguire says:
====================
Fix issues with libbpf BTF typed dump code. Patch 1 addresses handling
of unaligned data. Patch 2 fixes issues Andrii noticed when compiling
on ppc64le. Patch 3 simplifies typed dump by getting rid of allocation
of dump data structure which tracks dump state etc.
Changes since v1:
- Andrii suggested using a function instead of a macro for checking
alignment of data, and pointed out that we need to consider dump
ptr size versus native pointer size (patch 1)
====================
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
By using the stack for this small structure, we avoid the need
for freeing memory in error paths.
Suggested-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/1626475617-25984-4-git-send-email-alan.maguire@oracle.com
Currently, when userspace reads a datagram with a buffer that is
smaller than this datagram, the data will be truncated and only
part of it can be received by users. It doesn't seem right that
users don't know the datagram size and have to use a huge buffer
to read it to avoid the truncation.
This patch to fix it by keeping the skb in rcv queue until the
whole data is read by users. Only the last msg of the datagram
will be marked with MSG_EOR, just as TCP/SCTP does.
Note that this will work as above only when MSG_EOR is set in the
flags parameter of recvmsg(), so that it won't break any old user
applications.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__s64 can be defined as either long or long long, depending on the
architecture. On ppc64le it's defined as long, giving this error:
In file included from btf_dump.c:22:
btf_dump.c: In function 'btf_dump_type_data_check_overflow':
libbpf_internal.h:111:22: error: format '%lld' expects argument of
type 'long long int', but argument 3 has type '__s64' {aka 'long int'}
[-Werror=format=]
111 | libbpf_print(level, "libbpf: " fmt, ##__VA_ARGS__); \
| ^~~~~~~~~~
libbpf_internal.h:114:27: note: in expansion of macro '__pr'
114 | #define pr_warn(fmt, ...) __pr(LIBBPF_WARN, fmt, ##__VA_ARGS__)
| ^~~~
btf_dump.c:1992:3: note: in expansion of macro 'pr_warn'
1992 | pr_warn("unexpected size [%lld] for id [%u]\n",
| ^~~~~~~
btf_dump.c:1992:32: note: format string is defined here
1992 | pr_warn("unexpected size [%lld] for id [%u]\n",
| ~~~^
| |
| long long int
| %ld
Cast to size_t and use %zu instead.
Reported-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/1626475617-25984-3-git-send-email-alan.maguire@oracle.com
In nf_tables_commit, if nf_tables_commit_audit_alloc fails, it does not
free the adp variable.
Fix this by adding nf_tables_commit_audit_free which frees
the linked list with the head node adl.
backtrace:
kmalloc include/linux/slab.h:591 [inline]
kzalloc include/linux/slab.h:721 [inline]
nf_tables_commit_audit_alloc net/netfilter/nf_tables_api.c:8439 [inline]
nf_tables_commit+0x16e/0x1760 net/netfilter/nf_tables_api.c:8508
nfnetlink_rcv_batch+0x512/0xa80 net/netfilter/nfnetlink.c:562
nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:634 [inline]
nfnetlink_rcv+0x1fa/0x220 net/netfilter/nfnetlink.c:652
netlink_unicast_kernel net/netlink/af_netlink.c:1314 [inline]
netlink_unicast+0x2c7/0x3e0 net/netlink/af_netlink.c:1340
netlink_sendmsg+0x36b/0x6b0 net/netlink/af_netlink.c:1929
sock_sendmsg_nosec net/socket.c:702 [inline]
sock_sendmsg+0x56/0x80 net/socket.c:722
Reported-by: syzbot <syzkaller@googlegroups.com>
Reported-by: kernel test robot <lkp@intel.com>
Fixes: c520292f29 ("audit: log nftables configuration change events once per table")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nguy/next-queue
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2021-07-16
Vinicius Costa Gomes says:
Add support for steering traffic to specific RX queues using Flex Filters.
As the name implies, Flex Filters are more flexible than using
Layer-2, VLAN or MAC address filters, one of the reasons is that they
allow "AND" operations more easily, e.g. when the user wants to steer
some traffic based on the source MAC address and the packet ethertype.
Future work include adding support for offloading tc-u32 filters to
the hardware.
The series is divided as follows:
Patch 1/5, add the low level primitives for configuring Flex filters.
Patch 2/5 and 3/5, allow ethtool to manage Flex filters.
Patch 4/5, when specifying filters that have multiple predicates, use
Flex filters.
Patch 5/5, Adds support for exposing the i225 LEDs using the LED subsystem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If data is packed, data structures can store it outside of usual
boundaries. For example a 4-byte int can be stored on a unaligned
boundary in a case like this:
struct s {
char f1;
int f2;
} __attribute((packed));
...the int is stored at an offset of one byte. Some platforms have
problems dereferencing data that is not aligned with its size, and
code exists to handle most cases of this for BTF typed data display.
However pointer display was missed, and a simple function to test if
"ptr_is_aligned(data, data_sz)" would help clarify this code.
Suggested-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/1626475617-25984-2-git-send-email-alan.maguire@oracle.com
The commit 9a5605505d (" bonding: Add struct bond_ipesc to manage SA") is causing
following build error when XFRM is not selected in kernel config.
lld: error: undefined symbol: xfrm_dev_state_flush
>>> referenced by bond_main.c:3453 (drivers/net/bonding/bond_main.c:3453)
>>> net/bonding/bond_main.o:(bond_netdev_event) in archive drivers/built-in.a
Fixes: 9a5605505d (" bonding: Add struct bond_ipesc to manage SA")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: Taehee Yoo <ap420073@gmail.com>
CC: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of commit c7289b1c8a ("arm64: tegra: Enable SMMU support on
Tegra194"), SMMU support is enabled system-wide on Tegra194. However,
there was a bit of overlap between the SMMU enablement and the PCIe
support addition, so the PCIe device tree nodes are missing the iommus
and interconnects properties. This in turn leads to SMMU faults for
these devices, since by default the ARM SMMU will fault.
Add the iommus and interconnects properties to all the PCIe device
tree nodes to restore their functionality.
Fixes: c7289b1c8a ("arm64: tegra: Enable SMMU support on Tegra194")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Each i225 has three LEDs. Export them via the LED class framework.
Each LED is controllable via sysfs. Example:
$ cd /sys/class/leds/igc_led0
$ cat brightness # Current Mode
$ cat max_brightness # 15
$ echo 0 > brightness # Mode 0
$ echo 1 > brightness # Mode 1
The brightness field here reflects the different LED modes ranging
from 0 to 15.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently flex filters are only used for filters containing user data.
However, it makes sense to utilize them also for filters having
multiple conditions, because that's not supported by the driver at the
moment. Add it.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Allows Flex Filters to be installed.
The previous restriction to the types of filters that can be installed
can now be lifted.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use the flex filter mechanism to extend the current ethtool filter
operations by intercoperating the user data. This allows to match
eight more bytes within a Ethernet frame in addition to macs, ether
types and vlan.
The matching pattern looks like this:
* dest_mac [6]
* src_mac [6]
* tpid [2]
* vlan tci [2]
* ether type [2]
* user data [8]
This can be used to match Profinet traffic classes by FrameID range.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The Intel i225 NIC has the possibility to add flex filters which can
match up to the first 128 byte of a packet. These filters are useful
for all kind of packet matching. One particular use case is Profinet,
as the different traffic classes are distinguished by the frame id
range which cannot be matched by any other means.
Add code to configure and enable flex filters.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The release_sock() is blocking function, it would change the state
after sleeping. use wait_woken() instead.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once the new schema interrupt-controller/arm,vic.yaml is added, we get
the below warnings:
arch/arm/boot/dts/versatile-ab.dt.yaml:
intc@10140000: $nodename:0: 'intc@10140000' does not match
'^interrupt-controller(@[0-9a-f,]+)*$'
arch/arm/boot/dts/versatile-ab.dt.yaml:
intc@10140000: 'clear-mask' does not match any of the regexes
Fix the node names for the interrupt controller to conform
to the standard node name interrupt-controller@.. Also drop invalid
clear-mask property.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210701132118.759454-1-sudeep.holla@arm.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
pci_ioremap_bar() and pci_ioremap_wc_bar() shared similar implementations
but differed in unimportant ways. Align them by adding a shared helper,
__pci_ioremap_resource().
Upgrade warning message to error level, since it indicates a driver defect.
Remove WARN_ON() from WC path in favor of the error message.
[bhelgaas: commit log, use ioremap() since pci_iomap_range() doesn't add
anything]
Link: https://lore.kernel.org/r/20210713102436.304693-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>