This is a simple optimization for fifo waiting that improves scrolling
performance by 5%. If the queue has more free entries that what we
consume, we can skip the costly register read next time.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Ville Syrjälä <syrjala@sci.fi>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reading the registers without waiting for engine idle returns
unpredictable values. These unpredictable values result in display
corruption - if atyfb_imageblit reads the content of DP_PIX_WIDTH with the
bit DP_HOST_TRIPLE_EN set (from previous invocation), the driver would
never ever clear the bit, resulting in display corruption.
We don't want to wait for idle because it would degrade performance, so
this patch modifies the driver so that it never reads accelerator
registers.
HOST_CNTL doesn't have to be read, we can just write it with
HOST_BYTE_ALIGN because no other part of the driver cares if
HOST_BYTE_ALIGN is set.
DP_PIX_WIDTH is written in the functions atyfb_copyarea and atyfb_fillrect
with the default value and in atyfb_imageblit with the value set according
to the source image data.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Ville Syrjälä <syrjala@sci.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
The code for manual bit triple is not endian-clean. It builds the variable
"hostdword" using byte accesses, therefore we must read the variable with
"le32_to_cpu".
The patch also enables (hardware or software) bit triple only if the image
is monochrome (image->depth). If we want to blit full-color image, we
shouldn't use the triple code.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Ville Syrjälä <syrjala@sci.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
On Sun Ultra 5, it happens that the dot clock is not set up properly for
some videomodes. For example, if we set the videomode "r1024x768x60" in
the firmware, Linux would incorrectly set a videomode with refresh rate
180Hz when booting (suprisingly, my LCD monitor can display it, although
display quality is very low).
The reason is this: Older mach64 cards set the divider in the register
VCLK_POST_DIV. The register has four 2-bit fields (the field that is
actually used is specified in the lowest two bits of the register
CLOCK_CNTL). The 2 bits select divider "1, 2, 4, 8". On newer mach64 cards,
there's another bit added - the top four bits of PLL_EXT_CNTL extend the
divider selection, so we have possible dividers "1, 2, 4, 8, 3, 5, 6, 12".
The Linux driver clears the top four bits of PLL_EXT_CNTL and never sets
them, so it can work regardless if the card supports them. However, the
sparc64 firmware may set these extended dividers during boot - and the
mach64 driver detects incorrect dot clock in this case.
This patch makes the driver read the additional divider bit from
PLL_EXT_CNTL and calculate the initial refresh rate properly.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Ville Syrjälä <syrjala@sci.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
The udlfb driver maintained an open count and cleaned up itself when the
count reached zero. But the console is also counted in the reference count
- so, if the user unplugged the device, the open count would not drop to
zero and the driver stayed loaded with console attached. If the user
re-plugged the adapter, it would create a device /dev/fb1, show green
screen and the access to the console would be lost.
The framebuffer subsystem has reference counting on its own - in order to
fix the unplug bug, we rely the framebuffer reference counting. When the
user unplugs the adapter, we call unregister_framebuffer unconditionally.
unregister_framebuffer will unbind the console, wait until all users stop
using the framebuffer and then call the fb_destroy method. The fb_destroy
cleans up the USB driver.
This patch makes the following changes:
* Drop dlfb->kref and rely on implicit framebuffer reference counting
instead.
* dlfb_usb_disconnect calls unregister_framebuffer, the rest of driver
cleanup is done in the function dlfb_ops_destroy. dlfb_ops_destroy will
be called by the framebuffer subsystem when no processes have the
framebuffer open or mapped.
* We don't use workqueue during initialization, but initialize directly
from dlfb_usb_probe. The workqueue could race with dlfb_usb_disconnect
and this racing would produce various kinds of memory corruption.
* We use usb_get_dev and usb_put_dev to make sure that the USB subsystem
doesn't free the device under us.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
cc: Dave Airlie <airlied@redhat.com>
Cc: Bernie Thompson <bernie@plugable.com>,
Cc: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
broadsheetfb is a platform driver and it should not be used on x86.
It should be used only by single ARM PXA board so add the dependency
in Kconfig.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Use a more familiar naming pattern for our variables in the sprite plane
init function.
v2: Drop the redundant 'plane' from plane_formats and num_planes_formats
too
v3: Rebase due to ->max_stride() and ->check_plane() changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20181005125817.22576-11-ville.syrjala@linux.intel.com
There's not much point in following the primary vs. sprite split
for the SKL+ universal plane init code. The only difference is
of our own doing in the form of the .check_plane(). Let's make
a small exception for that little detail and otherwise share
the same code to initialize all the universal planes.
Eventually we should eliminate the mess around .check_plane()
as well, but for now let's be happy with some code reduction.
v2: Remember to set up plane->has_fbc
Make skl_plane_has_ccs() static
v3: Rebase due to NV12, rename some variables
v4: Don't leave the color_encoding/range props behind
v5: Rebase dur to blend properties, skl_plane_max_stride() and
skl_plane_check()
v6: Make skl_update_plane() static
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20181005125817.22576-10-ville.syrjala@linux.intel.com
when gate MSDC0_HCLK, access register will hang, even the MSDC driver
will never accessing register after HCLK was gated, but for safety, need
gate the bus_clk(which used to access register) too.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On MT2712 MSDC0/3, HCLK/bus-clk need gate/ungate together,
or will hang when access MSDC register.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull the common plane+plane_state allocation into a small helper.
Reduces the amount of boilerplate in the plane initialization
functions.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181005125817.22576-9-ville.syrjala@linux.intel.com
No point in having each caller of intel_create_plane_state() initialize
the scaler_id to -1. Instead just do it in intel_create_plane_state().
Previously we left scaler_id at 0 for pre-SKL platforms, but I can't
see how initializing it to -1 always would cause any harm.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181005125817.22576-8-ville.syrjala@linux.intel.com
All SKL+ universal planes support the same set of formats (with the
exception of NV12 which we don't expose yet). Make the format lists
for primary and sprites the same.
And make the format list const while at it.
v2: Deal with the "planar" format list as well
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181005125817.22576-7-ville.syrjala@linux.intel.com
Plane scaling is not supported with specific pixel formats. Disallow
plane scaling when such a format is used. Currently the only such
pixel format we expose is C8, but in case we add more in the future
let's make it easy to deal with them.
v2: Redo due to plane_check() refactoring
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20181005125817.22576-6-ville.syrjala@linux.intel.com
All CNL universal planes support horizontal mirroring. Currently
we expose the capability only for the primary plane. Expose it
for the overlay planes as well.
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181005125817.22576-5-ville.syrjala@linux.intel.com
We're currently not providing the possible_crtcs mask to
drm_universal_plane_init() for primary/cursor planes. While that does
work on account of drm_crtc_init_with_planes() filling those up
for us, it's inconsisten with what we're doing for sprite planes.
Let's just always pass the possible_crtcs bitmask to
drm_universal_plane_init(). This does assume that crtc->index
== pipe. But we're already making that assumption elsewhere so
it doesn't seem like a very big sin here.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181005125817.22576-3-ville.syrjala@linux.intel.com
Lookup regulators for Vdd and Vdda during probe, and enable them when the
component is linked.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a device tree documentation file for the wm8782 stereo DAC to describe
the regulator handles.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
no functional change, just hygiene.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
-----BEGIN PGP SIGNATURE-----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=lDis
-----END PGP SIGNATURE-----
Merge tag 'v4.19-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into fbdev-for-next
This is the 4.19-rc7 release
Sync with upstream (which now contains fbdev-v4.19-rc7 changes) to
prepare a base for fbdev-v4.20 changes.
The code had been clearing a namespace being deleted as the current
path while that namespace was still in the path siblings list. It is
possible a new IO could set that namespace back to the current path
since it appeared to be an eligable path to select, which may result in
a use-after-free error.
This patch ensures a namespace being removed is not eligable to be reset
as a current path prior to clearing it as the current path.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Previously only cancelled dma map of a ggtt page when the ggtt entry was
cleared. This patch will cancel dma map of an old ggtt page as well when
the ggtt entry is updated with new page address.
Fixes: 7598e8700e9a(drm/i915/gvt: Missed to cancel dma map for ggtt entries)
Signed-off-by: Hang Yuan <hang.yuan@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced the "fall-through:"
comment with a proper "fall through", which is what GCC is
expecting to find.
Addresses-Coverity-ID: 1373880 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced the
"deliberate fall-through" comment with a proper "fall through"
at the bottom of the case, which is what GCC is expecting to find.
Addresses-Coverity-ID: 1373887 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Recent versions of checkpatch have a new warning based on a documented
preference of Linus to not use bool in structures due to wasted space and
the size of bool is implementation dependent. For more information, see
the email thread at https://lkml.org/lkml/2017/11/21/384
fix checkpatch --strict issues:
-CHECK: Avoid using bool structure members because of possible alignment
issues - see: https://lkml.org/lkml/2017/11/21/384
-WARNING: Avoid using bool as bitfield. Prefer bool bitfields as
unsigned int or u<8|16|32>
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch internalizes the dma_inprogress into mmci dma interfaces.
This allows to simplify and prepare the next dma callbacks
for mmci host ops. dma_inprogress is called in mmci_dma_data_error
and mmci_dma_finalize.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch internalizes the management of dma map/unmap into
mmci dma interfaces. This allows to simplify and prepare the next dma
callbacks for mmci host ops.
mmci_dma_unmap was called in mmci_data_irq & mmci_cmd_irq functions
and can be integrated in mmci_dma_data_error.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for r8a7744 SoC. Renesas RZ/G1N (R8A7744) MMCIF is identical
to the R-Car Gen2 family.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for r8a7744 SoC. Renesas RZ/G1N (R8A7744) SDHI is identical
to the R-Car Gen2 family.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The OMAP HSMMC driver has some elaborate and hairy handling for
passing GPIO card detect and write protect lines from a boardfile
into the driver: the machine defines a struct omap2_hsmmc_info
that is copied into struct omap_hsmmc_platform_data by
omap_hsmmc_pdata_init() in arch/arm/mach-omap2/hsmmc.c.
However the .gpio_cd and .gpio_wp fields are not copied from
omap2_hsmmc_info to omap_hsmmc_platform_data by
omap_hsmmc_pdata_init() so they remain unused. The only platform
defining omap2_hsmmc_info also define both to -1, unused.
It turn out there are no boardfiles passing any valid GPIO
lines into the OMAP HSMMC driver at all. And since we are not
going to add any more OMAP2 boardfiles, we can delete this
card detect and write protect handling altogether.
This seems to also fix a bug: the card detect callback
mmc_gpio_get_cd() in the slot GPIO core needs to be called
by drivers utilizing slot GPIO. It appears the the boardfile
quirks were not doing this right, so this would only get
called for boardfiles, i.e. since no boardfile was using it,
never.
Just assign mmc_gpio_get_cd() unconditionally to omap_hsmmc_ops
.get_cd() so card detects from the device tree works.
AFAICT card detect with GPIO lines assigned from
mmc_of_parse() are not working at the moment, but that is
no regression since it probably never worked.
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cover detection appears to be a feature protecting the SD
card on mobile phones with a slide-cover, such as some Nokia
phones. The idea seems to be to not allow access to the
SD card when the cover is open.
It is only usable with platform data from board files, but
no board file in the kernel is using it, yet it takes up
a sizeable chunk of code in the OMAP HSMMC driver.
Since we do not add new board files for the OMAPs any target
that need this should anyway reimplement it properly using
the device tree, so delete this legacy code.
The driver is marked as orphan in MAINTAINERS by the way.
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sd8686 "libertas" SDIO adapter's power is controlled with WLAN_RST
and WLAN_PD pins -- pretty much the same way as sd8787. Allow building
the power sequencing driver along with the libertas Wi-Fi driver.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver is complicating things for no reason: the "cd"
GPIO can easily be retrieved from the device tree if present
using just mmc_gpiod_request_cd(), which will fetch the
descriptor from the device tree using the standard binding
just fine.
If the retrieveal is successful, we also request the IRQ.
As a result the private subdriver data can be removed
entirely.
Cc: Weijun Yang <york.yang@csr.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The platform data for the PXAv3 driver allows passing a card
detect GPIO, but this code is not used in the kernel.
In order to not encourage the use of the old global GPIO
numberspace we need to remove this.
Card detect (and write protect) GPIO can easily be added into
the driver using machine descriptor tables instead, and the
descriptor-based (gpiod) variants of the slot GPIO APIs.
Cc: Jisheng Zhang <jszhang@marvell.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver is complicating things for no reason: the "cd"
GPIO can easily be retrieved from the device tree if present
using just mmc_gpiod_request_cd(), which will fetch the
descriptor from the device tree using the standard binding
just fine.
Cc: Viresh Kumar <vireshk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All the machines using the MMCI are passing GPIOs for the
card detect and write protect using the device tree or
descriptor table (one single case, Integrator/AP IM-PD1).
Drop support for passing global GPIO numbers through
platform data, noone is using it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If hosts provides ops->adma_write_desc, we should not fall back to the
general sdhci_adma_write_desc().
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As you are already in ISR, it is unnecessary to call spin_lock_irqsave.
Signed-off-by: jun qian <hangdianqj@163.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix warning when running with CONFIG_DMA_API_DEBUG_SG=y by allocating a
device_dma_parameters structure and filling in the max segment size. The
size used is the result of a discussion with Renesas hardware engineers
and unfortunately not found in the datasheet.
renesas_sdhi_internal_dmac ee140000.sd: DMA-API: mapping sg segment
longer than device claims to support [len=126976] [max=65536]
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[wsa: simplified some logic after validating intended dma_parms life cycle
and added comment]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eMMC controller is also a new timing mode controller, but it doesn't
have the timing mode switch. It does however have signal delay and
calibration controls, typical of Allwinner MMC controllers that support
the new timing mode.
Enable the new timing mode setting for the A64 eMMC controller. This
also enables MMC HS-DDR modes, which gives higher throughput for eMMC
chips that support it, and can deliver such throughput.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Newer sunxi mmc controller variants support what they call the "new
timing mode". Support for this was implemented in two ways, according
to the hardware that was seen at the time.
The first type retained the old timing mode, and both the clock and mmc
controllers had switches to select which mode was used. Both switches
had to be set to the same setting. This variant was denoted with the
.has_timings_switch field in the sunxi_mmc_cfg structure. This hardware
is only seen on the A83T.
The second type did away with the old timing mode. The clock controller
no longer had the mode selection or clock delay setting bits. In some
cases the mmc controller retained its mode selection bit, but this
always needed to be set to the new mode, or instabilities would occur.
In a few cases, such as the A64 and H6 eMMC controller, the mode
selection bit is gone, but the controller still behaves like the new
timing mode, requiring the module clock to be double the card clock
in DDR transfer modes. This variant is denoted with the
.needs_new_timings field.
This patch adds more comments explaining the two fields, as well as
the possibly nonexistent mode switch in the mmc controller.
The .has_timings_switch is renamed to .ccu_has_timings_switch to clarify
its meaning.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds the initial support of Secure Digital Host Controller
Interface compliant controller found in some latest Spreadtrum chipsets.
This patch has been tested on the version of SPRD-R11 controller.
R11 is a variant based on SD v4.0 specification.
With this driver, R11 mmc can be initialized, can be mounted, read and
written.
Original-by: Billows Wu <billows.wu@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When Host Version 4 Enable is set to 1, SDMA uses ADMA System Address
register (05Fh-058h) instead of using register (000h-004h) to indicate
its system address of data location. The register (000h-004h) is
re-assigned to 32-bit Block Count and Auto CMD23 argument, so then SDMA
may use Auto CMD23.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
