Latency is in the eye of the beholder. In the case where a client stops
and waits for the gpu, give that request chain a small priority boost
(not so that it overtakes higher priority clients, to preserve the
external ordering) so that ideally the wait completes earlier.
v2: Tvrtko recommends to keep the boost-from-user-stall as small as
possible and to allow new client flows to be preferred for interactivity
over stalls.
Testcase: igt/gem_sync/switch-default
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001144755.7978-3-chris@chris-wilson.co.uk
Currently, the backend scheduling code abuses struct_mutex into order to
have a global lock to manipulate a temporary list (without widespread
allocation) and to protect against list modifications. This is an
extraneous coupling to struct_mutex and further can not extend beyond
the local device.
Pull all the code that needs to be under the one true lock into
i915_scheduler.c, and make it so.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001144755.7978-2-chris@chris-wilson.co.uk
Taken from an idea used for FQ_CODEL, we give the first request of a
new request flows a small priority boost. These flows are likely to
correspond with short, interactive tasks and so be more latency sensitive
than the longer free running queues. As soon as the client has more than
one request in the queue, further requests are not boosted and it settles
down into ordinary steady state behaviour. Such small kicks dramatically
help combat the starvation issue, by allowing each client the opportunity
to run even when the system is under heavy throughput load (within the
constraints of the user selected priority).
v2: Mark the preempted request as the start of a new flow, to prevent a
single client being continually gazumped by its peers.
Testcase: igt/benchmarks/rrul
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001144755.7978-1-chris@chris-wilson.co.uk
To make sure the infoframe unpack functions don't end up examining
stack garbage or oopsing, let's pass in the size of the buffer.
v2: Convert tda1997x.c as well (kbuild test robot)
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: linux-media@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180920185145.1912-3-ville.syrjala@linux.intel.com
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Add new code to count canceled pending cluster reservations on bigalloc
file systems and to reduce the cluster reservation count on all file
systems using delayed allocation. This replaces old code in
ext4_da_page_release_reservations that was incorrect.
Signed-off-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The system image guid is a read-only field which is used by the TC
offloads code to determine if two mlx5 devices belong to the same
ASIC while adding flows.
Read this once and save it on the core device rather than querying each
time an offloaded flow is added.
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently we practically never report checksum unnecessary, because
for all IP packets we take the checksum complete path.
Enable non-default runs with reprorting checksum unnecessary, using
an ethtool private flag. This can be useful for performance evals
and other explorations.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We can report checksum unnecessary also when the L3 checksum
flag on the cqe is set and there's no L4 header.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Increased the amount of channels the representors can open to be the
amount of CPUs. The default amount opened remains one.
Used the standard NIC netdev functions to:
* Set RSS params when building the representors' params.
* Setup an indirect TIR and RQT for the representors upon
initialization.
* Create a TTC flow table for the representors' indirect TIR (when
creating the TTC table, mlx5e_set_ttc_basic_params() is not called,
in order to avoid setting the inner_ttc param, which is not needed).
Added ethtool control to the representors for setting and querying
the amount of open channels. Additionally, included logic in the
representors' ethtool set channels handler which controls a
representor's vport rx rule, so that if there is one open channel
the rx rule steers traffic to the representor's direct TIR, whereas
if there is more than one channel, the rx rule steers traffic to the
new TTC flow table.
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Towards enabling RSS for the vport representors, expose the functions for
querying the rss hash key size and indirection table size via ethtool.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Towards enabling RSS for the vport representors, extract the
procedure for building a device's RSS params, and expose the
function.
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Change the driver functions that deal with creating indirect tirs
to get a flag telling if inner ttc is desired.
A pre-step for enabling rss on the vport representors, where
inner ttc is not needed.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently the destination for the representor e-switch rx rule is
a TIR number. Towards changing that to potentially be a flow table,
as part of enabling RSS for representors, modify the signature of
the related e-switch API to get a flow destination.
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Cleaning up the flow of the representors' rx initialization, towards
enabling RSS for the representors.
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Enabled checksum and TSO offloads for the representors, in
order to increase their performance, which is required to
increase the performance of flows that cannot be offloaded.
Checksum offloads contribute to a general acceleration of all
traffic (to around 150%), whereas the TSO offload contributes
to a prominent acceleration of the representor's TX for traffic
flows with larger than MTU sized packets (to around 200%). This
is the usual case for TCP streams, as the PF, which serves as
the uplink representor, and the VF representors employ GRO before
forwarding the packets to the representor.
GRO was enabled implicitly for the representors beforehand, and
is explicitly enabled here to ensure that the representors preserve
the performance boost it provides (of around 200%) when working in
tandem with the TSO offload by the forwardee, which is the standard
case as both the PF and the VF representors employ HW TSO.
The impact of these changes can be seen in the following
measurements taken on a setup of a VM over a VF, connected
to OVS via the VF representor, to an external host:
Before current changes:
TCP Throughput [Gb/s]
External host to VM ~ 10.5
VM to external host ~ 23.5
With just checksum offloads enabled:
TCP Throughput [Gb/s]
External host to VM ~ 14.9
VM to external host ~ 28.5
With the TSO offload also enabled:
TCP Throughput [Gb/s]
External host to VM ~ 30.5
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The representors' RQ size was not large enough for them to achieve
high enough performance, and therefore needed to be enlarged, while
suffering a minimum hit to its memory usage. To achieve this the
representors RQ size was increased, and its type was changed to be a
striding RQ if it is supported.
Towards that goal the following changes were made:
* Extracted the sequence for setting the standard netdev's RQ parmas
into a function
* Replaced the sequence for setting the representor's RQ params with
the standard sequence
The impact of this change can be seen in the following measurements
taken on a setup of a VM over a VF, connected to OVS via the VF
representor, to an external host:
Before current change:
TCP Throughput [Gb/s]
VM to external host ~ 7.2
With the current change (measured with a striding RQ):
TCP Throughput [Gb/s]
VM to external host ~ 23.5
Each representor now consumes 2 [MB] of memory for its packet
buffers.
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Allow using partial masks for L3 addresses and L4 ports across
the place.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Modify ext4_ext_remove_space() and the code it calls to correct the
reserved cluster count for pending reservations (delayed allocated
clusters shared with allocated blocks) when a block range is removed
from the extent tree. Pending reservations may be found for the clusters
at the ends of written or unwritten extents when a block range is removed.
If a physical cluster at the end of an extent is freed, it's necessary
to increment the reserved cluster count to maintain correct accounting
if the corresponding logical cluster is shared with at least one
delayed and unwritten extent as found in the extents status tree.
Add a new function, ext4_rereserve_cluster(), to reapply a reservation
on a delayed allocated cluster sharing blocks with a freed allocated
cluster. To avoid ENOSPC on reservation, a flag is applied to
ext4_free_blocks() to briefly defer updating the freeclusters counter
when an allocated cluster is freed. This prevents another thread
from allocating the freed block before the reservation can be reapplied.
Redefine the partial cluster object as a struct to carry more state
information and to clarify the code using it.
Adjust the conditional code structure in ext4_ext_remove_space to
reduce the indentation level in the main body of the code to improve
readability.
Signed-off-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Ext4 does not always reduce the reserved cluster count by the number
of clusters allocated when mapping a delayed extent. It sometimes
adds back one or more clusters after allocation if delalloc blocks
adjacent to the range allocated by ext4_ext_map_blocks() share the
clusters newly allocated for that range. However, this overcounts
the number of clusters needed to satisfy future mapping requests
(holding one or more reservations for clusters that have already been
allocated) and premature ENOSPC and quota failures, etc., result.
Ext4 also does not reduce the reserved cluster count when allocating
clusters for non-delayed allocated writes that have previously been
reserved for delayed writes. This also results in overcounts.
To make it possible to handle reserved cluster accounting for
fallocated regions in the same manner as used for other non-delayed
writes, do the reserved cluster accounting for them at the time of
allocation. In the current code, this is only done later when a
delayed extent sharing the fallocated region is finally mapped.
Address comment correcting handling of unsigned long long constant
from Jan Kara's review of RFC version of this patch.
Signed-off-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The code in ext4_da_map_blocks sometimes reserves space for more
delayed allocated clusters than it should, resulting in premature
ENOSPC, exceeded quota, and inaccurate free space reporting.
Fix this by checking for written and unwritten blocks shared in the
same cluster with the newly delayed allocated block. A cluster
reservation should not be made for a cluster for which physical space
has already been allocated.
Signed-off-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Add new pending reservation mechanism to help manage reserved cluster
accounting. Its primary function is to avoid the need to read extents
from the disk when invalidating pages as a result of a truncate, punch
hole, or collapse range operation.
Signed-off-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Ext4 contains a few functions that are used to search for delayed
extents or blocks in the extents status tree. Rather than duplicate
code to add new functions to search for extents with different status
values, such as written or a combination of delayed and unwritten,
generalize the existing code to search for caller-specified extents
status values. Also, move this code into extents_status.c where it
is better associated with the data structures it operates upon, and
where it can be more readily used to implement new extents status tree
functions that might want a broader scope for i_es_lock.
Three missing static specifiers in RFC version of patch reported and
fixed by Fengguang Wu <fengguang.wu@intel.com>.
Signed-off-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
In flow steering, if asked to, the hardware matches on the first ethertype
which is not vlan. It's possible to set a rule as follows, which is meant
to match on untagged packet, but will match on a vlan packet:
tc filter add dev eth0 parent ffff: protocol ip flower ...
To avoid this for packets with single tag, we set vlan masks to tell
hardware to check the tags for every matched packet.
Fixes: 095b6cfd69 ('net/mlx5e: Add TC vlan match parsing')
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The code that deals with eswitch vport bw guarantee was going beyond the
eswitch vport array limit, fix that. This was pointed out by the kernel
address sanitizer (KASAN).
The error from KASAN log:
[2018-09-15 15:04:45] BUG: KASAN: slab-out-of-bounds in
mlx5_eswitch_set_vport_rate+0x8c1/0xae0 [mlx5_core]
Fixes: c9497c9890 ("net/mlx5: Add support for setting VF min rate")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If the peer device was already unbound, then do not attempt to modify
it's resources, otherwise we will crash on dereferencing non-existing
device.
Fixes: 5c65c564c9 ("net/mlx5e: Support offloading TC NIC hairpin flows")
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
- Add support for CMT timer clocks on R-Car V3H,
- Add support for SHDI and various timer clocks on R-Car V3M,
- Add support for the new RZ/A2 (R7S9210) SoC, including early clock
support for the Renesas CPG/MSSR driver,
- Add support for the new RZ/G1N (R8A7744) and RZ/G2E (R8A774C0) SoCs,
- Convert DT binding includes to SPDX license identifiers,
- Small fixes and clean ups.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCW63kQQAKCRCKwlD9ZEnx
cPWiAP0c+qXgc0qE3wy15qSaKekPB6vVCY+4LqMqUWboSzzgwgD+O5+woQ4x7KU5
ztFsE3mfXEZeDKu8naPCLjtiPLTOFwc=
=O51L
-----END PGP SIGNATURE-----
Merge tag 'clk-renesas-for-v4.20-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-renesas
Pull Renesas clk driver updates from Geert Uytterhoeven:
- Add support for CMT timer clocks on R-Car V3H
- Add support for SHDI and various timer clocks on R-Car V3M
- Add support for the new RZ/A2 (R7S9210) SoC, including early clock
support for the Renesas CPG/MSSR driver
- Add support for the new RZ/G1N (R8A7744) and RZ/G2E (R8A774C0) SoCs
- Convert DT binding includes to SPDX license identifiers
* tag 'clk-renesas-for-v4.20-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: r7s9210: Add SPI clocks
clk: renesas: r7s9210: Move table update to separate function
clk: renesas: r7s9210: Convert some clocks to early
clk: renesas: cpg-mssr: Add early clock support
clk: renesas: r8a77970: Add TPU clock
clk: renesas: r8a77990: Fix incorrect PLL0 divider in comment
dt-bindings: clock: renesas: cpg-mssr: Document r8a774c0
clk: renesas: cpg-mssr: Add r8a774c0 support
clk: renesas: Add r8a774c0 CPG Core Clock Definitions
clk: renesas: r8a7743: Add r8a7744 support
clk: renesas: Add r8a7744 CPG Core Clock Definitions
dt-bindings: clock: renesas: cpg-mssr: Document r8a7744 binding
dt-bindings: clock: renesas: Convert to SPDX identifiers
clk: renesas: cpg-mssr: Add R7S9210 support
clk: renesas: r8a77970: Add TMU clocks
clk: renesas: r8a77970: Add CMT clocks
clk: renesas: r9a06g032: Fix UART34567 clock rate
clk: renesas: r8a77970: Add SD0H/SD0 clocks for SDHI
clk: renesas: r8a77980: Add CMT clocks
- clk-pll driver improvements and updates
- add axg audio controller system clocks
- drop mpll3 from the possible pcie clock parent of the axg
- register meson8b clock controller early
-----BEGIN PGP SIGNATURE-----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=GF25
-----END PGP SIGNATURE-----
Merge tag 'meson-clk-4.20-1' of https://github.com/BayLibre/clk-meson into clk-meson
Pull meson clk driver updates from Jerome Brunet:
- clk-pll driver improvements and updates
- add axg audio controller system clocks
- drop mpll3 from the possible pcie clock parent of the axg
- register meson8b clock controller early
* tag 'meson-clk-4.20-1' of https://github.com/BayLibre/clk-meson:
clk: meson: meson8b: use the regmap in the internal reset controller
clk: meson: meson8b: register the clock controller early
clk: meson-axg: pcie: drop the mpll3 clock parent
clk: meson: axg: round audio system master clocks down
clk: meson: clk-pll: drop hard-coded rates from pll tables
clk: meson: clk-pll: remove od parameters
clk: meson: clk-pll: drop CLK_GET_RATE_NOCACHE where unnecessary
clk: meson: clk-pll: add enable bit
/kisskb/src/drivers/gpu/drm/i915/i915_irq.c: warning: 'gu_misc_iir' may be used uninitialized in this function [-Wuninitialized]: => 3120:10
Silence the compiler warning by ensuring that the local variable is
initialised and removing the guard that is confusing the older gcc.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: df0d28c185 ("drm/i915/icl: GSE interrupt moves from DE_MISC to GU_MISC")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180926104718.17462-1-chris@chris-wilson.co.uk
(cherry picked from commit 7a90938332)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Let us reuse the already defined has_csr check and not
redefine it.
The main difference is that in effect this will flip .has_csr to 1
(via GEN9_FEATURES which GEN11_FEATURES pulls in).
Suggested-by: Imre Deak <imre.deak@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=107382
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1534527210-16841-1-git-send-email-anusha.srivatsa@intel.com
(cherry picked from commit da4468a1aa)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Add SD card write-protect pin configuration to be sure that it will be
properly pulled down to indicate write access.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
"S3C2410 PM Suspend Memory CRC" feature (controlled by
SAMSUNG_PM_CHECK config option) is incompatible with highmem
(uses phys_to_virt() instead of proper mapping) which is used by
the majority of Exynos boards. The issue manifests itself in OOPS
on affected boards, i.e. on Odroid-U3 I got the following one:
Unable to handle kernel paging request at virtual address f0000000
pgd = 1c0f9bb4
[f0000000] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[<c0458034>] (crc32_le) from [<c0121f8c>] (s3c_pm_makecheck+0x34/0x54)
[<c0121f8c>] (s3c_pm_makecheck) from [<c0121efc>] (s3c_pm_run_res+0x74/0x8c)
[<c0121efc>] (s3c_pm_run_res) from [<c0121ecc>] (s3c_pm_run_res+0x44/0x8c)
[<c0121ecc>] (s3c_pm_run_res) from [<c01210b8>] (exynos_suspend_enter+0x64/0x148)
[<c01210b8>] (exynos_suspend_enter) from [<c018893c>] (suspend_devices_and_enter+0x9ec/0xe74)
[<c018893c>] (suspend_devices_and_enter) from [<c0189534>] (pm_suspend+0x770/0xc04)
[<c0189534>] (pm_suspend) from [<c0186ce8>] (state_store+0x6c/0xcc)
[<c0186ce8>] (state_store) from [<c09db434>] (kobj_attr_store+0x14/0x20)
[<c09db434>] (kobj_attr_store) from [<c02fa63c>] (sysfs_kf_write+0x4c/0x50)
[<c02fa63c>] (sysfs_kf_write) from [<c02f97a4>] (kernfs_fop_write+0xfc/0x1e4)
[<c02f97a4>] (kernfs_fop_write) from [<c027b198>] (__vfs_write+0x2c/0x140)
[<c027b198>] (__vfs_write) from [<c027b418>] (vfs_write+0xa4/0x160)
[<c027b418>] (vfs_write) from [<c027b5d8>] (ksys_write+0x40/0x8c)
[<c027b5d8>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
Add PLAT_S3C24XX, ARCH_S3C64XX and ARCH_S5PV210 dependencies to
SAMSUNG_PM_CHECK config option to hide it on Exynos platforms.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
As Grygorii Strashko pointed out, the runtime PM use count of the
children can be whatever at suspend and we should not use it. So
let's just suspend ti-sysc at noirq level and get rid of some code.
Let's also remove the PM_SLEEP ifdef and use __maybe_unused as the
PM code already deals with the ifdefs.
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PCI kirin driver compilation produces the following section mismatch
warning:
WARNING: vmlinux.o(.text+0x4758cc): Section mismatch in reference from
the function kirin_pcie_probe() to the function
.init.text:kirin_add_pcie_port()
The function kirin_pcie_probe() references
the function __init kirin_add_pcie_port().
This is often because kirin_pcie_probe lacks a __init
annotation or the annotation of kirin_add_pcie_port is wrong.
Remove '__init' from kirin_add_pcie_port() to fix it.
Fixes: fc5165db24 ("PCI: kirin: Add HiSilicon Kirin SoC PCIe controller driver")
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Document RZ/G1N (R8A7744) SoC bindings.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable the USB3 and USB2 phys implemented in UniPhier SoCs.
These phys are necessary for dwc3 and ehci controllers driving
the USB ports on arm64 UniPhier SoCs.
Since the USB host drivers are already built-in, so only the phy
driver are missing to allow booting with USB devices.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Document RZ/G1N (r8a7744) SoC specific bindings.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
It recently came to light that userspace can execute WFI, and that
the arm64 kernel doesn't trap this event. This sounds rather benign,
but the kernel should decide when it wants to wait for an interrupt,
and not userspace.
Let's trap WFI and immediately return after having skipped the
instruction. This effectively makes WFI a rather expensive NOP.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
* TKIP implementation in new devices;
* Fix for the shared antenna setting in 22000 series;
* Report that we set the RU offset in HE code;
* Fix some register addresses in 22000 series;
* Fix one FW feature TLV that had a conflict with another value;
* A couple of fixes for SoftAP mode;
* Work continues for new 22560 hardware;
* Some fixes in the datapath;
* Some debugging and other general fixes;
* Some cleanups, small improvements and other general fixes;
-----BEGIN PGP SIGNATURE-----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=5Y2V
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2018-09-28' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Second set of iwlwifi patches for 4.20
* TKIP implementation in new devices;
* Fix for the shared antenna setting in 22000 series;
* Report that we set the RU offset in HE code;
* Fix some register addresses in 22000 series;
* Fix one FW feature TLV that had a conflict with another value;
* A couple of fixes for SoftAP mode;
* Work continues for new 22560 hardware;
* Some fixes in the datapath;
* Some debugging and other general fixes;
* Some cleanups, small improvements and other general fixes;
Trivial fix to spelling mistake struct field name, rename it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure that wifi device is of supported variant by checking it's CHIP ID
before completing a probe sequence.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Waiting for "completion" to be set in FW load thread can not be used
in case PCIe remove is called before FW load work was scheduled.
Just wait for work completion instead to avoid problems.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Extract platform-independent PCIe driver code into a separate file, and
use it from platform-specific modules.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
