SWAP support on ARC was fixed earlier by
commit 6e3761145a ("ARC: Fix CONFIG_SWAP")
so now we may safely enable it on platforms that
have external media like USB and SD-card.
Note: it was already allowed for HSDK
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: stable@vger.kernel.org # 6e3761145a: ARC: Fix CONFIG_SWAP
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Otherwise kernel uses random MAC which is not very conveniet.
With that change in place use might set desired MAC in U-Boot
with "setenv ethaddr 11:22:33:44:55:66", save environment and
then from boot to boot the same MAC will be used by the kernel.
One other note for this to happen it's required to pass
board's .dtb in U-Boot's "bootm" command like that:
------------------->8-----------------
bootm 0x82000000 - 0x84000000
------------------->8-----------------
Here 0x82000000 is location of uImage while
0x80000000 is location of either axs10x.dtb or hsdk.dtb
previously loaded from SD-card, USB storage or TFTP server.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: stable@vger.kernel.org # 4.14
Cc: devicetree@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- Remove CONFIG_DEFAULT_HOSTNAME from defconfigs
There's no reason to set the same hostname to all ARC boards
by default. It usually gets overwritten by init scripts anyways.
- Remove disabled CONFIG_DEVKMEM from defconfigs
It is disabled by default
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
As the new bindings are already in place in sama5d2.dtsi and that it's used
in the only Mainline board for this product (at91-sama5d2_ptc_ek.dts), we can
safely remove the old bindings.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix a typo. No functional change made by this patch.
Signed-off-by: Jay Foster <jayfoster@ieee.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
There is no need to initialize pm_bu since it is used only if backup
mode is selected. In case backup mode initialization fails (which means
pm_bu is invalid) the ULP0 mode will be selected.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The email was botched in one entry, and I also forgot to update the
location of the git tree. It'll be under the linux-block umbrella, just
with different branches.
Reported-by: Baruch Siach <baruch@tkos.co.il>
Fixes: 7634ccd2da ("libata: maintainership update")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds SATA0 pin, group and function to the R8A77965 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[wsa: rebased to upstream base]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds SATA clock to the R8A77965 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[wsa: rebased to upstream base]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On R-Car V3H, RCLK can be switched between EXTALR and the On-Chip
Oscillator using mode pin MD19.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Make the existing support for selecting between clean and SSCG clocks
using MD12 more generic, to allow using other mode pins for arbitrary
clock selection.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to R-Car Gen3 Hardware Manual Rev.1.00, R-Car D3 has the
RCLK Frequency Control Register (RCKCR), which determines the OSC and
RINT predivider values, and selection of the RCLK clock source between
RINT and the On-Chip Oscillator.
Hence change the OSC and RINT clock definitions to use the RCKCR
divider, and add the missing On-Chip Oscillator and RCLK clock source
switching logic.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to R-Car Gen3 Hardware Manual Rev.1.00, R-Car E3 has the
RCLK Frequency Control Register (RCKCR), which determines the OSC and
RINT predivider values, and selection of the RCLK clock source between
RINT and the On-Chip Oscillator.
Hence change the OSC and RINT clock definitions to use the RCKCR
divider, and add the missing On-Chip Oscillator and RCLK clock source
switching logic.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add a clock type and macro for defining clocks where the parent and
divider are selected based on the value of the RCKCR.CKSEL bit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add support for defining fixed rate clocks, to be used for on-chip
oscillators.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
R-Car Gen3 Hardware Manual Rev.0.54 documents the relation between the
MD13 and MD14 mode pins, and the OSC EXTAL predivider, as used by the
OSC clock. Hence augment the configuration structure with all
documented predivider values.
Add the OSC clock using the configured predivider.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
R-Car Gen3 Hardware Manual Rev.0.52 documents the relation between the
MD13 and MD14 mode pins, and the OSC EXTAL predivider, as used by the
OSC and RINT RCLK clocks. Hence augment the configuration structure
with all documented predivider values.
According to R-Car Gen3 Hardware Manual Rev.1.00, R-Car M3-N does not
have the CPG_RCKCR register. Change the OSC and RINT clock definitions
to use the OSC EXTAL predivider instead, which is supported on all R-Car
M3-N SoC revisions.
Inspired by a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
R-Car Gen3 Hardware Manual Rev.0.52 documents the relation between the
MD13 and MD14 mode pins, and the OSC EXTAL predivider, as used by the
OSC and RINT RCLK clocks. Hence augment the configuration structure
with all documented predivider values.
According to R-Car Gen3 Hardware Manual Rev.0.53, the CPG_RCKCR
register was removed in R-Car M3-W ES1.1. Change the OSC and RINT
clock definitions to use the OSC EXTAL predivider instead, which is
supported on all R-Car M3-W SoC revisions.
Inspired by a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
R-Car Gen3 Hardware Manual Rev.0.52 documents the relation between the
MD13 and MD14 mode pins, and the OSC EXTAL predivider, as used by the
OSC and RINT RCLK clocks. Hence augment the configuration structure
with all documented predivider values.
According to R-Car Gen3 Hardware Manual Rev.0.53, the CPG_RCKCR
register was removed in R-Car H3 ES2.0. Change the OSC and RINT
clock definitions to use the OSC EXTAL predivider instead, which is
supported on all R-Car H3 SoC revisions.
Inspired by a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add a clock type and macro for defining clocks using the OSC EXTAL
predivider combined with a fixed divider.
On most R-Car Gen3 SoCs, the predivider value depends on mode pins, and
thus must be specified in the configuration structure.
Inspired by a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
All other internal clock names have a period prepended.
Hence rename the internal RCLK from "rint" to ".r", and move it to the
section where all other internal clocks are defined.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds a 70ms mystery delay to the bridge driver in enable.
By experimentation, it seems like it can go anywhere up until we
initiate semi-auto link training. If we don't have the delay, link
training fails.
I tried to root cause this as best I could, but neither the datasheet
for the panel nor the bridge mention a delay of this magnitude in their
timing requirements. So for now, add the mystery delay until someone
figures out a better fix.
Changes in v3:
- Added to the set
Cc: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180813213058.184821-8-sean@poorly.run
This patch sets the pin muxing for the I2S controllers
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
[codrin.ciubotariu@microchip.com: added pin muxing for the second
controller]
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This patch adds DT nodes for I2S0 and I2S1. It also adds an alias for
each I2S node.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
[codrin.ciubotariu@microchip.com: removed unnecessary clock phandles]
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This patch adds two clock muxes for the two I2S
buses present on sama5d2 platforms.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add generic resistive touch device which is connected to ADC block
inside the SAMA5D2 SoC
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In some cases 32-bit PAE PV guests still write PTEs directly instead of
using hypercalls. This is especially bad when clearing a PTE as this is
done via 32-bit writes which will produce intermediate L1TF attackable
PTEs.
Change the code to use hypercalls instead.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
A specially crafted file system can trick empty_inline_dir() into
reading past the last valid entry in a inline directory, and then run
into the end of xattr marker. This will trigger a divide by zero
fault. Fix this by using the size of the inline directory instead of
dir->i_size.
Also clean up error reporting in __ext4_check_dir_entry so that the
message is clearer and more understandable --- and avoids the division
by zero trap if the size passed in is zero. (I'm not sure why we
coded it that way in the first place; printing offset % size is
actually more confusing and less useful.)
https://bugzilla.kernel.org/show_bug.cgi?id=200933
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reported-by: Wen Xu <wen.xu@gatech.edu>
Cc: stable@vger.kernel.org
In harmony with ATF and U-Boot outputs [1] and [2], the new board is
based on M3-N revision ES1.1 and the amount of memory present on SiP
is 2GiB, contiguously addressed.
The amount of RAM is mentioned based on the assumption that it is
encoded in the board id/string. There is some evidence supporting this
in form of last-digit-mismatch between two R-Car H3 ES2.0 ULCB board
ids, one with 4GiB and one with 8GiB of RAM (see [3]).
[1] BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.1.0.21
BL2: PRR is R-Car M3N Ver.1.1
[2] U-Boot 2015.04-00295-*
CPU: Renesas Electronics R8A77965 rev 1.1
---8<----
DRAM: 1.9 GiB
Bank #0: 0x048000000 - 0x0bfffffff, 1.9 GiB
---8<----
[3] https://patchwork.kernel.org/patch/10555957/#22169325
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add device tree bindings documentation for Renesas RZ/A2 (r7s9210) SoC.
Also document new option for "renesas,bsid"
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add device tree bindings documentation for Renesas RZ/G2M (r8a774a1) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for identifying the RZ/A2M (R7S9210) SoC.
Also add support for reading the BSID register which is a different format
than the PRR.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the RZ/A2 SoC to the Renesas SoC collection.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds support for identifying the RZ/G2M (r8a774a1) SoC.
It corrects the original RZ/G SoC family name to RZ/G1 and also
adds support for the new RZ/G2 SoC family.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The internal LVDS encoder now has DT bindings separate from the DU. Port
the r8a7795 and r8a7796 device trees over to the new model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up SYS-DMAC0, SYS-DMAC1 and SYS-DMAC2 to IPMMU-DS0 and IPMMU-DS1
following the R-Car Gen3 Rev.1.00 (April 2018) datasheet.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Browsing the DTS for all the R-Car SoCs with similar part numbers
makes my head hurt, so to improve the user friendliness of the
DTS code base include R-Car product name in each DTSI file.
Product names are derived from
Documentation/devicetree/bindings/arm/shmobile.txt
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe RWDT in the R8A77980 SoC device tree.
Enable RWDT on the Condor and V3H Starter Kit boards.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the Renesas RZ/G2M (R8A774A1) SoC in the ARM64 defconfig.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Browsing the DTS for all the R-Car SoCs with similar part numbers
still makes my head hurt, so to improve the user friendliness of
the 32-bit ARM DTS code base include R-Car Gen1 product names for
each DTSI file.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DA9063 OnKey subnode to DA9063 PMIC node on Stout.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DA9063 RTC and OnKey subnode to DA9063 PMIC node on Silk.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Specify EtherAVB PHY IRQ in the board specific device tree, now that we
have GPIO support.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DA9063 PMIC node to the I2C bus.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
