[ Upstream commit f65727be3f ]
If the clock mhdp->clk was not enabled in cdns_mhdp_probe(), it should not
be disabled in any path.
The return value of clk_prepare_enable() is not checked. If mhdp->clk was
not enabled, it may be disabled in the error path of cdns_mhdp_probe()
(e.g., if cdns_mhdp_load_firmware() fails) or in cdns_mhdp_remove() after
a successful cdns_mhdp_probe() call.
Use the devm_clk_get_enabled() helper function to ensure proper call
balance for mhdp->clk.
Found by Linux Verification Center (linuxtesting.org) with Klever.
Fixes: fb43aa0acd ("drm: bridge: Add support for Cadence MHDP8546 DPI/DP bridge")
Signed-off-by: Vitalii Mordan <mordan@ispras.ru>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250214154632.1907425-1-mordan@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed15511a77 ]
If the driver initialization fails, the vkms_exit() function might
access an uninitialized or freed default_config pointer and it might
double free it.
Fix both possible errors by initializing default_config only when the
driver initialization succeeded.
Reported-by: Louis Chauvet <louis.chauvet@bootlin.com>
Closes: https://lore.kernel.org/all/Z5uDHcCmAwiTsGte@louis-chauvet-laptop/
Fixes: 2df7af93fd ("drm/vkms: Add vkms_config type")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Thomas Zimmermann <tzimmremann@suse.de>
Reviewed-by: Louis Chauvet <louis.chauvet@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250212084912.3196-1-jose.exposito89@gmail.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28b529a985 ]
Fix "mapping sg segment longer than device claims to support" warning by
setting the max segment size.
Fixes: d76271d226 ("drm: xlnx: DRM/KMS driver for Xilinx ZynqMP DisplayPort Subsystem")
Reviewed-by: Sean Anderson <sean.anderson@linux.dev>
Tested-by: Sean Anderson <sean.anderson@linux.dev>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250115-xilinx-formats-v2-10-160327ca652a@ideasonboard.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5072fc77f ]
Fix a typo where V compare incorrectly compares av[] with av[] itself,
which can result in HDCP failure.
The loop of V compare is expected to iterate for 5 times
which compare V array form av[0][] to av[4][].
It should check loop counter reach the last statement "i == 5"
before return true
Fixes: 0989c02c7a ("drm/bridge: it6505: fix HDCP CTS compare V matching")
Signed-off-by: Hermes Wu <Hermes.wu@ite.com.tw>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250121-fix-hdcp-v-comp-v4-1-185f45c728dc@ite.com.tw
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6bbce873a9 ]
[Why]
The RAD of sideband message printed today is incorrect.
For RAD stored within MST branch
- If MST branch LCT is 1, it's RAD array is untouched and remained as 0.
- If MST branch LCT is larger than 1, use nibble to store the up facing
port number in cascaded sequence as illustrated below:
u8 RAD[0] = (LCT_2_UFP << 4) | LCT_3_UFP
RAD[1] = (LCT_4_UFP << 4) | LCT_5_UFP
...
In drm_dp_mst_rad_to_str(), it wrongly to use BIT_MASK(4) to fetch the port
number of one nibble.
[How]
Adjust the code by:
- RAD array items are valuable only for LCT >= 1.
- Use 0xF as the mask to replace BIT_MASK(4)
V2:
- Document how RAD is constructed (Imre)
V3:
- Adjust the comment for rad[] so kdoc formats it properly (Lyude)
Fixes: 2f015ec6ea ("drm/dp_mst: Add sideband down request tracing + selftests")
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250113091100.3314533-2-Wayne.Lin@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 229adcffdb ]
The bounding rectangle is adjusted to ensure it aligns to
SSD132X_SEGMENT_WIDTH, which may adjust the pitch. Calculate the pitch
after aligning the left and right edge.
Fixes: fdd591e00a ("drm/ssd130x: Add support for the SSD132x OLED controller family")
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250115110139.1672488-3-jkeeping@inmusicbrands.com
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e14484677 ]
The ssd132x buffer is encoded one pixel per nibble, with two pixels in
each byte. When encoding an 8-bit greyscale input, take the top 4-bits
as the value and ensure the two pixels are distinct and do not overwrite
each other.
Fixes: fdd591e00a ("drm/ssd130x: Add support for the SSD132x OLED controller family")
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250115110139.1672488-2-jkeeping@inmusicbrands.com
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d40d4fae6 ]
The only reason for the ssd130x-spi driver to have an spi_device_id table
is that the SPI core always reports an "spi:" MODALIAS, even when the SPI
device has been registered via a Device Tree Blob.
Without spi_device_id table information in the module's metadata, module
autoloading would not work because there won't be an alias that matches
the MODALIAS reported by the SPI core.
This spi_device_id table is not needed for device matching though, since
the of_device_id table is always used in this case. For this reason, the
struct spi_driver .id_table member is currently not set in the SPI driver.
Because the spi_device_id table is always required for module autoloading,
the SPI core checks during driver registration that both an of_device_id
table and a spi_device_id table are present and that they contain the same
entries for all the SPI devices.
Not setting the .id_table member in the driver then confuses the core and
leads to the following warning when the ssd130x-spi driver is registered:
[ 41.091198] SPI driver ssd130x-spi has no spi_device_id for sinowealth,sh1106
[ 41.098614] SPI driver ssd130x-spi has no spi_device_id for solomon,ssd1305
[ 41.105862] SPI driver ssd130x-spi has no spi_device_id for solomon,ssd1306
[ 41.113062] SPI driver ssd130x-spi has no spi_device_id for solomon,ssd1307
[ 41.120247] SPI driver ssd130x-spi has no spi_device_id for solomon,ssd1309
[ 41.127449] SPI driver ssd130x-spi has no spi_device_id for solomon,ssd1322
[ 41.134627] SPI driver ssd130x-spi has no spi_device_id for solomon,ssd1325
[ 41.141784] SPI driver ssd130x-spi has no spi_device_id for solomon,ssd1327
[ 41.149021] SPI driver ssd130x-spi has no spi_device_id for solomon,ssd1331
To prevent the warning, set the .id_table even though it's not necessary.
Since the check is done even for built-in drivers, drop the condition to
only define the ID table when the driver is built as a module. Finally,
rename the variable to use the "_spi_id" convention used for ID tables.
Fixes: 74373977d2 ("drm/solomon: Add SSD130x OLED displays SPI support")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241231114516.2063201-1-javierm@redhat.com
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 574f5ee2c8 ]
Each bridge instance creates up to four auxiliary devices with different
names. However, their IDs are always zero, causing duplicate filename
errors when a system has multiple bridges:
sysfs: cannot create duplicate filename '/bus/auxiliary/devices/ti_sn65dsi86.gpio.0'
Fix this by using a unique instance ID per bridge instance. The
instance ID is derived from the I2C adapter number and the bridge's I2C
address, to support multiple instances on the same bus.
Fixes: bf73537f41 ("drm/bridge: ti-sn65dsi86: Break GPIO and MIPI-to-eDP bridge into sub-drivers")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/7a68a0e3f927e26edca6040067fb653eb06efb79.1733840089.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3424c8f53b ]
The infamous mmap_lock taken in copy_from/to_user() can be often
problematic when it's called inside another mutex, as they might lead
to deadlocks.
In the case of ALSA timer code, the bad pattern is with
guard(mutex)(®ister_mutex) that covers copy_from/to_user() -- which
was mistakenly introduced at converting to guard(), and it had been
carefully worked around in the past.
This patch fixes those pieces simply by moving copy_from/to_user() out
of the register mutex lock again.
Fixes: 3923de04c8 ("ALSA: pcm: oss: Use guard() for setup")
Reported-by: syzbot+2b96f44164236dda0f3b@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/67dd86c8.050a0220.25ae54.0059.GAE@google.com
Link: https://patch.msgid.link/20250321172653.14310-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45ff65e30d ]
For 'ti,j7200-cpb-audio' compatible, there is support for only one PLL for
48k. For 11025, 22050, 44100 and 88200 sampling rates, due to absence of
J721E_CLK_PARENT_44100, we get EINVAL while running any audio application.
Add support for these rates by using the 48k parent clock and adjusting
the clock for these rates later in j721e_configure_refclk.
Fixes: 6748d05590 ("ASoC: ti: Add custom machine driver for j721e EVM (CPB and IVI)")
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://patch.msgid.link/20250318113524.57100-1-j-choudhary@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a0c72c1da ]
The workaround for Dell machines to skip the pin-shutup for mic pins
introduced alc_headset_mic_no_shutup() that is replaced from the
generic snd_hda_shutup_pins() for certain codecs. The problem is that
the call is done unconditionally even if spec->no_shutup_pins is set.
This seems causing problems on other platforms like Lenovo.
This patch corrects the behavior and the driver honors always
spec->no_shutup_pins flag and skips alc_headset_mic_no_shutup() if
it's set.
Fixes: dad3197da7 ("ALSA: hda/realtek - Fixup headphone noise via runtime suspend")
Reported-and-tested-by: Oleg Gorobets <oleg.goro@gmail.com>
Link: https://patch.msgid.link/20250315143020.27184-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f0d2de417 ]
GOcontroll produces embedded linux systems and IO modules to use in
these systems, add its prefix.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Link: https://patch.msgid.link/20250226-initial_display-v2-2-23fafa130817@gocontroll.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad5a0970f8 ]
Currently the return value from spi_setup() is not checked for a failure.
It is unlikely it will ever fail in this particular case but it is still
better to add this check for the sake of completeness and correctness. This
is cheap since it is performed once when the device is being probed.
Handle spi_setup() return value.
Found by Linux Verification Center (linuxtesting.org) with Svace.
Fixes: 872fc0b6bd ("ASoC: cs35l41: Set the max SPI speed for the whole device")
Signed-off-by: Vitaliy Shevtsov <v.shevtsov@mt-integration.ru>
Link: https://patch.msgid.link/20250304115643.2748-1-v.shevtsov@mt-integration.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a248294a3 ]
On the Dell Inspiron 3505 the battery temperature is always
0.1 degrees larger than the temperature show inside the OEM
application.
Emulate this behaviour to avoid showing strange looking values
like 29.1 degrees.
Fixes: 0331b1b0ba ("platform/x86: dell-ddv: Fix temperature scaling")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20250305053009.378609-2-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4878e0b14c ]
Sparse reports:
dell-uart-backlight.c:328:29: warning: symbol
'dell_uart_bl_serdev_driver' was not declared. Should it be static?
Fix it by making the symbol static.
Fixes: 484bae9e4d ("platform/x86: Add new Dell UART backlight driver")
Reviewed-by: Mario Limonciello <maroi.limonciello@amd.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20250304160639.4295-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 886ca11a0c ]
Sparse reports:
lenovo-yoga-tab2-pro-1380-fastcharger.c:222:29: warning: symbol
'yt2_1380_fc_serdev_driver' was not declared. Should it be static?
Fix that by making the symbol static.
Fixes: b2ed33e8d4 ("platform/x86: Add lenovo-yoga-tab2-pro-1380-fastcharger driver")
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20250304160639.4295-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72e1c440c8 ]
Variable allocated by charlcd_alloc() should be released
by charlcd_free(). The following patch changed kfree() to
charlcd_free() to fix an API misuse.
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: 718e05ed92 ("auxdisplay: Introduce hd44780_common.[ch]")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2b96a6818 ]
In allegro_probe(), the v4l2 device is not unregistered in the error
path, which results in a memory leak. Fix it by calling
v4l2_device_unregister() before returning error.
Fixes: d74d4e2359 ("media: allegro: move driver out of staging")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fcb42b383 ]
The HEVC driver needs to set the start_bit field explicitly to avoid
causing corrupted frames when the VP9 decoder is used in parallel. The
reason for this problem is that the VP9 and the HEVC decoder share this
register.
Fixes: cb5dd5a0fa ("media: hantro: Introduce G2/HEVC decoder")
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Tested-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5aab0438e ]
The LDO5 regulator has two configuration registers, but only
LDO5CTRL_L contains the bits for enabling/disabling the regulator.
Fixes: 0935ff5f1f ("regulator: pca9450: add pca9450 pmic driver")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://patch.msgid.link/20241218152842.97483-6-frieder@fris.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d55f31e290 ]
ia32_emulation_override_cmdline() is an early_param() arg and these
are only needed at boot time. In fact, all other early_param() functions
in arch/x86 seem to have '__init' annotation and
ia32_emulation_override_cmdline() is the only exception.
Fixes: a11e097504 ("x86: Make IA32_EMULATION boot time configurable")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Nikolay Borisov <nik.borisov@suse.com>
Link: https://lore.kernel.org/all/20241210151650.1746022-1-vkuznets%40redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dda366083e ]
Guest FPUs manage vCPU FPU states. They are allocated via
fpu_alloc_guest_fpstate() and are resized in fpstate_realloc() when XFD
features are enabled.
Since the introduction of guest FPUs, there have been inconsistencies in
the kernel buffer size and xfeatures:
1. fpu_alloc_guest_fpstate() uses fpu_user_cfg since its introduction. See:
69f6ed1d14 ("x86/fpu: Provide infrastructure for KVM FPU cleanup")
36487e6228 ("x86/fpu: Prepare guest FPU for dynamically enabled FPU features")
2. __fpstate_reset() references fpu_kernel_cfg to set storage attributes.
3. fpu->guest_perm uses fpu_kernel_cfg, affecting fpstate_realloc().
A recent commit in the tip:x86/fpu tree partially addressed the inconsistency
between (1) and (3) by using fpu_kernel_cfg for size calculation in (1),
but left fpu_guest->xfeatures and fpu_guest->perm still referencing
fpu_user_cfg:
https://lore.kernel.org/all/20250218141045.85201-1-stanspas@amazon.de/1937e18cc3 ("x86/fpu: Fix guest FPU state buffer allocation size")
The inconsistencies within fpu_alloc_guest_fpstate() and across the
mentioned functions cause confusion.
Fix them by using fpu_kernel_cfg consistently in fpu_alloc_guest_fpstate(),
except for fields related to the UABI buffer. Referencing fpu_kernel_cfg
won't impact functionalities, as:
1. fpu_guest->perm is overwritten shortly in fpu_init_guest_permissions()
with fpstate->guest_perm, which already uses fpu_kernel_cfg.
2. fpu_guest->xfeatures is solely used to check if XFD features are enabled.
Including supervisor xfeatures doesn't affect the check.
Fixes: 36487e6228 ("x86/fpu: Prepare guest FPU for dynamically enabled FPU features")
Suggested-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Chao Gao <chao.gao@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Sean Christopherson <seanjc@google.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Link: https://lore.kernel.org/r/20250317140613.1761633-1-chao.gao@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8085fcd78c ]
The CONFIG_X86_ESPFIX64 version of exc_double_fault() can return to its
caller, but the !CONFIG_X86_ESPFIX64 version never does. In the latter
case the compiler and/or objtool may consider it to be implicitly
noreturn.
However, due to the currently inflexible way objtool detects noreturns,
a function's noreturn status needs to be consistent across configs.
The current workaround for this issue is to suppress unreachable
warnings for exc_double_fault()'s callers. Unfortunately that can
result in ORC coverage gaps and potentially worse issues like inert
static calls and silently disabled CPU mitigations.
Instead, prevent exc_double_fault() from ever being implicitly marked
noreturn by forcing a return behind a never-taken conditional.
Until a more integrated noreturn detection method exists, this is likely
the least objectionable workaround.
Fixes: 55eeab2a8a ("objtool: Ignore exc_double_fault() __noreturn warnings")
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Brendan Jackman <jackmanb@google.com>
Link: https://lore.kernel.org/r/d1f4026f8dc35d0de6cc61f2684e0cb6484009d1.1741975349.git.jpoimboe@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c96fff391c ]
The poll man page says POLLRDNORM is equivalent to POLLIN. For poll(),
it seems that if user sets pollfd with POLLRDNORM in userspace, perf_poll
will not return until timeout even if perf_output_wakeup called,
whereas POLLIN returns.
Fixes: 76369139ce ("perf: Split up buffer handling from core code")
Signed-off-by: Tao Chen <chen.dylane@linux.dev>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/20250314030036.2543180-1-chen.dylane@linux.dev
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87886b32d6 ]
disable_irq_nosync_lockdep() disables interrupts with lockdep enabled to
avoid false positive reports by lockdep that a certain lock has not been
acquired with disabled interrupts. The user of this macros expects that
a lock can be acquried without disabling interrupts because the IRQ line
triggering the interrupt is disabled.
This triggers a warning on PREEMPT_RT because after
disable_irq_nosync_lockdep.*() the following spinlock_t now is acquired
with disabled interrupts.
On PREEMPT_RT there is no difference between spin_lock() and
spin_lock_irq() so avoiding disabling interrupts in this case works for
the two remaining callers as of today.
Don't disable interrupts on PREEMPT_RT in disable_irq_nosync_lockdep.*().
Closes: https://lore.kernel.org/760e34f9-6034-40e0-82a5-ee9becd24438@roeck-us.net
Fixes: e8106b941c ("[PATCH] lockdep: core, add enable/disable_irq_irqsave/irqrestore() APIs")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Suggested-by: "Steven Rostedt (Google)" <rostedt@goodmis.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20250212103619.2560503-2-bigeasy@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03f1444016 ]
When dpm_suspend() fails, some devices with power.direct_complete set
may not have been handled by device_suspend() yet, so runtime PM has
not been disabled for them yet even though power.direct_complete is set.
Since device_resume() expects that runtime PM has been disabled for all
devices with power.direct_complete set, it will attempt to reenable
runtime PM for the devices that have not been processed by device_suspend()
which does not make sense. Had those devices had runtime PM disabled
before device_suspend() had run, device_resume() would have inadvertently
enable runtime PM for them, but this is not expected to happen because
it would require ->prepare() callbacks to return positive values for
devices with runtime PM disabled, which would be invalid.
In practice, this issue is most likely benign because pm_runtime_enable()
will not allow the "disable depth" counter to underflow, but it causes a
warning message to be printed for each affected device.
To allow device_resume() to distinguish the "direct complete" devices
that have been processed by device_suspend() from those which have not
been handled by it, make device_suspend() set power.is_suspended for
"direct complete" devices.
Next, move the power.is_suspended check in device_resume() before the
power.direct_complete check in it to make it skip the "direct complete"
devices that have not been handled by device_suspend().
This change is based on a preliminary patch from Saravana Kannan.
Fixes: aae4518b31 ("PM / sleep: Mechanism to avoid resuming runtime-suspended devices unnecessarily")
Link: https://lore.kernel.org/linux-pm/20241114220921.2529905-2-saravanak@google.com/
Reported-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Link: https://patch.msgid.link/12627587.O9o76ZdvQC@rjwysocki.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2542a3f70e ]
Not all devices have an ACPI companion fwnode, so adev might be NULL.
This is similar to the commit cd2fd6eab4
("platform/x86: int3472: Check for adev == NULL").
Add a check for adev not being set and return -ENODEV in that case to
avoid a possible NULL pointer deref in int3402_thermal_probe().
Note, under the same directory, int3400_thermal_probe() has such a
check.
Fixes: 77e337c6e2 ("Thermal: introduce INT3402 thermal driver")
Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20250313043611.1212116-1-chenyuan0y@gmail.com
[ rjw: Subject edit, added Fixes: ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a121798ae6 ]
Commit
6eac36bb9e ("x86/resctrl: Allocate the cleanest CLOSID by searching closid_num_dirty_rmid")
added logic that causes resctrl to search for the CLOSID with the fewest dirty
cache lines when creating a new control group, if requested by the arch code.
This depends on the values read from the llc_occupancy counters. The logic is
applicable to architectures where the CLOSID effectively forms part of the
monitoring identifier and so do not allow complete freedom to choose an unused
monitoring identifier for a given CLOSID.
This support missed that some platforms may not have these counters. This
causes a NULL pointer dereference when creating a new control group as the
array was not allocated by dom_data_init().
As this feature isn't necessary on platforms that don't have cache occupancy
monitors, add this to the check that occurs when a new control group is
allocated.
Fixes: 6eac36bb9e ("x86/resctrl: Allocate the cleanest CLOSID by searching closid_num_dirty_rmid")
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Fenghua Yu <fenghuay@nvidia.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Amit Singh Tomar <amitsinght@marvell.com> # arm64
Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> # arm64
Tested-by: Babu Moger <babu.moger@amd.com>
Link: https://lore.kernel.org/r/20250311183715.16445-2-james.morse@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 231e341036 ]
The error path order of ie31200_init() is incorrect, fix it.
Fixes: 709ed1bcef ("EDAC/ie31200: Fallback if host bridge device is already initialized")
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Tested-by: Gary Wang <gary.c.wang@intel.com>
Link: https://lore.kernel.org/r/20250310011411.31685-4-qiuxu.zhuo@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3427befbbc ]
The DIMM size mask for {Sky, Kaby, Coffee} Lake is not bits{7:0},
but bits{5:0}. Fix it.
Fixes: 953dee9bbd ("EDAC, ie31200_edac: Add Skylake support")
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Tested-by: Gary Wang <gary.c.wang@intel.com>
Link: https://lore.kernel.org/r/20250310011411.31685-3-qiuxu.zhuo@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d59d844e31 ]
The EDAC_MC_LAYER_CHIP_SELECT layer pertains to the rank, not the DIMM.
Fix its size to reflect the number of ranks instead of the number of DIMMs.
Also delete the unused macros IE31200_{DIMMS,RANKS}.
Fixes: 7ee40b897d ("ie31200_edac: Introduce the driver")
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Tested-by: Gary Wang <gary.c.wang@intel.com>
Link: https://lore.kernel.org/r/20250310011411.31685-2-qiuxu.zhuo@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ae0042f4d ]
Subshell evaluations are not exempt from errexit, so if a command is
not available, `which` will fail and exit the script as a whole.
This causes the helpful error messages to not be printed if they are
tacked on using a `$?` comparison.
Resolve the issue by using chains of logical operators, which are not
subject to the effects of errexit.
Fixes: e37c1877ba ("scripts/selinux: modernize mdp")
Signed-off-by: Tim Schumacher <tim.schumacher1@huawei.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6834d9c99 ]
During stress-testing, we found a kmemleak report for perf_event:
unreferenced object 0xff110001410a33e0 (size 1328):
comm "kworker/4:11", pid 288, jiffies 4294916004
hex dump (first 32 bytes):
b8 be c2 3b 02 00 11 ff 22 01 00 00 00 00 ad de ...;....".......
f0 33 0a 41 01 00 11 ff f0 33 0a 41 01 00 11 ff .3.A.....3.A....
backtrace (crc 24eb7b3a):
[<00000000e211b653>] kmem_cache_alloc_node_noprof+0x269/0x2e0
[<000000009d0985fa>] perf_event_alloc+0x5f/0xcf0
[<00000000084ad4a2>] perf_event_create_kernel_counter+0x38/0x1b0
[<00000000fde96401>] hardlockup_detector_event_create+0x50/0xe0
[<0000000051183158>] watchdog_hardlockup_enable+0x17/0x70
[<00000000ac89727f>] softlockup_start_fn+0x15/0x40
...
Our stress test includes CPU online and offline cycles, and updating the
watchdog configuration.
After reading the code, I found that there may be a race between cleaning up
perf_event after updating watchdog and disabling event when the CPU goes offline:
CPU0 CPU1 CPU2
(update watchdog) (hotplug offline CPU1)
... _cpu_down(CPU1)
cpus_read_lock() // waiting for cpu lock
softlockup_start_all
smp_call_on_cpu(CPU1)
softlockup_start_fn
...
watchdog_hardlockup_enable(CPU1)
perf create E1
watchdog_ev[CPU1] = E1
cpus_read_unlock()
cpus_write_lock()
cpuhp_kick_ap_work(CPU1)
cpuhp_thread_fun
...
watchdog_hardlockup_disable(CPU1)
watchdog_ev[CPU1] = NULL
dead_event[CPU1] = E1
__lockup_detector_cleanup
for each dead_events_mask
release each dead_event
/*
* CPU1 has not been added to
* dead_events_mask, then E1
* will not be released
*/
CPU1 -> dead_events_mask
cpumask_clear(&dead_events_mask)
// dead_events_mask is cleared, E1 is leaked
In this case, the leaked perf_event E1 matches the perf_event leak
reported by kmemleak. Due to the low probability of problem recurrence
(only reported once), I added some hack delays in the code:
static void __lockup_detector_reconfigure(void)
{
...
watchdog_hardlockup_start();
cpus_read_unlock();
+ mdelay(100);
/*
* Must be called outside the cpus locked section to prevent
* recursive locking in the perf code.
...
}
void watchdog_hardlockup_disable(unsigned int cpu)
{
...
perf_event_disable(event);
this_cpu_write(watchdog_ev, NULL);
this_cpu_write(dead_event, event);
+ mdelay(100);
cpumask_set_cpu(smp_processor_id(), &dead_events_mask);
atomic_dec(&watchdog_cpus);
...
}
void hardlockup_detector_perf_cleanup(void)
{
...
perf_event_release_kernel(event);
per_cpu(dead_event, cpu) = NULL;
}
+ mdelay(100);
cpumask_clear(&dead_events_mask);
}
Then, simultaneously performing CPU on/off and switching watchdog, it is
almost certain to reproduce this leak.
The problem here is that releasing perf_event is not within the CPU
hotplug read-write lock. Commit:
941154bd69 ("watchdog/hardlockup/perf: Prevent CPU hotplug deadlock")
introduced deferred release to solve the deadlock caused by calling
get_online_cpus() when releasing perf_event. Later, commit:
efe951d3de ("perf/x86: Fix perf,x86,cpuhp deadlock")
removed the get_online_cpus() call on the perf_event release path to solve
another deadlock problem.
Therefore, it is now possible to move the release of perf_event back
into the CPU hotplug read-write lock, and release the event immediately
after disabling it.
Fixes: 941154bd69 ("watchdog/hardlockup/perf: Prevent CPU hotplug deadlock")
Signed-off-by: Li Huafei <lihuafei1@huawei.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20241021193004.308303-1-lihuafei1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d985e4399a ]
The byte initialization values used with -ftrivial-auto-var-init=pattern
(CONFIG_INIT_STACK_ALL_PATTERN=y) depends on the compiler, architecture,
and byte position relative to struct member types. On i386 with Clang,
this includes the 0xFF value, which means it looks like nothing changes
between the leaf byte filling pass and the expected "stack wiping"
pass of the stackinit test.
Use the byte fill value of 0x99 instead, fixing the test for i386 Clang
builds.
Reported-by: ernsteiswuerfel
Closes: https://github.com/ClangBuiltLinux/linux/issues/2071
Fixes: 8c30d32b1a ("lib/test_stackinit: Handle Clang auto-initialization pattern")
Tested-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20250304225606.work.030-kees@kernel.org
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbb6224887 ]
The perf event should be marked disabled during the creation as
it is not ready to be scheduled until there is SBI PMU start call
or config matching is called with auto start. Otherwise, event add/start
gets called during perf_event_create_kernel_counter function.
It will be enabled and scheduled to run via perf_event_enable during
either the above mentioned scenario.
Fixes: 0cb74b65d2 ("RISC-V: KVM: Implement perf support without sampling")
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Link: https://lore.kernel.org/r/20250303-kvm_pmu_improve-v2-1-41d177e45929@rivosinc.com
Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a1e3bf61f ]
Support was added for Tegra234 in the referenced commit, but the Kconfig
was not updated to allow building for the arch.
Fixes: 273bc890a2 ("cpufreq: tegra194: Add support for Tegra234")
Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eeb87d17ac ]
The check before setting power.must_resume in device_suspend_noirq()
does not take power.child_count into account, but it should do that, so
use pm_runtime_need_not_resume() in it for this purpose and adjust the
comment next to it accordingly.
Fixes: 107d47b2b9 ("PM: sleep: core: Simplify the SMART_SUSPEND flag handling")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://patch.msgid.link/3353728.44csPzL39Z@rjwysocki.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1b65f3f7c ]
Turns out that this commit, about 10 years ago:
9ec23531fd ("sched/preempt, mm/fault: Trigger might_sleep() in might_fault() with disabled pagefaults")
... accidentally (and unnessecarily) put the lockdep part of
__might_fault() under CONFIG_DEBUG_ATOMIC_SLEEP=y.
This is potentially notable because large distributions such as
Ubuntu are running with !CONFIG_DEBUG_ATOMIC_SLEEP.
Restore the debug check.
[ mingo: Update changelog. ]
Fixes: 9ec23531fd ("sched/preempt, mm/fault: Trigger might_sleep() in might_fault() with disabled pagefaults")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lore.kernel.org/r/20241104135517.536628371@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72dafb5677 ]
The following commit:
1c811d403a ("x86/sev: Fix position dependent variable references in startup code")
introduced RIP_REL_REF() to force RIP-relative accesses to global variables,
as needed to prevent crashes during early SEV/SME startup code.
For completeness, RIP_REL_REF() should be used with additional variables during
sme_enable():
https://lore.kernel.org/all/CAMj1kXHnA0fJu6zh634=fbJswp59kSRAbhW+ubDGj1+NYwZJ-Q@mail.gmail.com/
Access these vars with RIP_REL_REF() to prevent problem reoccurence.
Fixes: 1c811d403a ("x86/sev: Fix position dependent variable references in startup code")
Signed-off-by: Kevin Loughlin <kevinloughlin@google.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/r/20241122202322.977678-1-kevinloughlin@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 976ba8da2f ]
The CONFIG_EISA menu was cleaned up in 2018, but this inadvertently
brought the option back on 64-bit machines: ISA remains guarded by
a CONFIG_X86_32 check, but EISA no longer depends on ISA.
The last Intel machines ith EISA support used a 82375EB PCI/EISA bridge
from 1993 that could be paired with the 440FX chipset on early Pentium-II
CPUs, long before the first x86-64 products.
Fixes: 6630a8e501 ("eisa: consolidate EISA Kconfig entry in drivers/eisa")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/20250226213714.4040853-11-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d3b81d4d8 ]
The init_task instance of struct task_struct is statically allocated and
may not contain the full FP state for userspace. As such, limit the copy
to the valid area of both init_task and 'dst' and ensure all memory is
initialized.
Note that the FP state is only needed for userspace, and as such it is
entirely reasonable for init_task to not contain parts of it.
Fixes: 5aaeb5c01c ("x86/fpu, sched: Introduce CONFIG_ARCH_WANTS_DYNAMIC_TASK_STRUCT and use it on x86")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Link: https://lore.kernel.org/r/20250226133136.816901-1-benjamin@sipsolutions.net
----
v2:
- Fix code if arch_task_struct_size < sizeof(init_task) by using
memcpy_and_pad.
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1937e18cc3 ]
Ongoing work on an optimization to batch-preallocate vCPU state buffers
for KVM revealed a mismatch between the allocation sizes used in
fpu_alloc_guest_fpstate() and fpstate_realloc(). While the former
allocates a buffer sized to fit the default set of XSAVE features
in UABI form (as per fpu_user_cfg), the latter uses its ksize argument
derived (for the requested set of features) in the same way as the sizes
found in fpu_kernel_cfg, i.e. using the compacted in-kernel
representation.
The correct size to use for guest FPU state should indeed be the
kernel one as seen in fpstate_realloc(). The original issue likely
went unnoticed through a combination of UABI size typically being
larger than or equal to kernel size, and/or both amounting to the
same number of allocated 4K pages.
Fixes: 69f6ed1d14 ("x86/fpu: Provide infrastructure for KVM FPU cleanup")
Signed-off-by: Stanislav Spassov <stanspas@amazon.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20250218141045.85201-1-stanspas@amazon.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9207cf776 ]
When doing error injection to some memory DIMMs on certain Intel Emerald
Rapids servers, the i10nm_edac missed error reports for some memory DIMMs.
Certain BIOS configurations may hide some memory controllers, and the
i10nm_edac doesn't enumerate these hidden memory controllers. However, the
ADXL decodes memory errors using memory controller physical indices even
if there are hidden memory controllers. Therefore, the memory controller
physical indices reported by the ADXL may mismatch the logical indices
enumerated by the i10nm_edac, resulting in missed error reports for some
memory DIMMs.
Fix this issue by creating a mapping table from memory controller physical
indices (used by the ADXL) to logical indices (used by the i10nm_edac) and
using it to convert the physical indices to the logical indices during the
error handling process.
Fixes: c545f5e412 ("EDAC/i10nm: Skip the absent memory controllers")
Reported-by: Kevin Chang <kevin1.chang@intel.com>
Tested-by: Kevin Chang <kevin1.chang@intel.com>
Reported-by: Thomas Chen <Thomas.Chen@intel.com>
Tested-by: Thomas Chen <Thomas.Chen@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20250214002728.6287-1-qiuxu.zhuo@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3698dd6b13 ]
We observed an issue that the CPU frequency can't raise up with a 100% CPU
load when NOHZ is off and the 'conservative' governor is selected.
'idle_time' can be negative if it's obtained from get_cpu_idle_time_jiffy()
when NOHZ is off. This was found and explained in commit 9485e4ca0b
("cpufreq: governor: Fix handling of special cases in dbs_update()").
However, commit 7592019634 ("cpufreq: governors: Fix long idle detection
logic in load calculation") introduced a comparison between 'idle_time' and
'samling_rate' to detect a long idle interval. While 'idle_time' is
converted to int before comparison, it's actually promoted to unsigned
again when compared with an unsigned 'sampling_rate'. Hence, this leads to
wrong idle interval detection when it's in fact 100% busy and sets
policy_dbs->idle_periods to a very large value. 'conservative' adjusts the
frequency to minimum because of the large 'idle_periods', such that the
frequency can't raise up. 'Ondemand' doesn't use policy_dbs->idle_periods
so it fortunately avoids the issue.
Correct negative 'idle_time' to 0 before any use of it in dbs_update().
Fixes: 7592019634 ("cpufreq: governors: Fix long idle detection logic in load calculation")
Signed-off-by: Jie Zhan <zhanjie9@hisilicon.com>
Reviewed-by: Chen Yu <yu.c.chen@intel.com>
Link: https://patch.msgid.link/20250213035510.2402076-1-zhanjie9@hisilicon.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 563bc2161b ]
When a task is enqueued and its parent cgroup se is already on_rq, this
parent cgroup se will not be enqueued again, and hence the root->min_slice
leaves unchanged. The same issue happens when a task is dequeued and its
parent cgroup se has other runnable entities, and the parent cgroup se
will not be dequeued.
Force propagating min_slice when se doesn't need to be enqueued or
dequeued. Ensure the se hierarchy always get the latest min_slice.
Fixes: aef6987d89 ("sched/eevdf: Propagate min_slice up the cgroup hierarchy")
Signed-off-by: Tianchen Ding <dtcccc@linux.alibaba.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20250211063659.7180-1-dtcccc@linux.alibaba.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f553741ac8 ]
A wakeup non-idle entity should preempt idle entity at any time,
but because of the slice protection of the idle entity, the non-idle
entity has to wait, so just cancel it.
This patch is aimed at minimizing the impact of SCHED_IDLE on
SCHED_NORMAL. For example, a task with SCHED_IDLE policy that sleeps for
1s and then runs for 3 ms, running cyclictest on the same cpu, has a
maximum latency of 3 ms, which is caused by the slice protection of the
idle entity. It is unreasonable. With this patch, the cyclictest latency
under the same conditions is basically the same on the cpu with idle
processes and on empty cpu.
[peterz: add helpers]
Fixes: 63304558ba ("sched/eevdf: Curb wakeup-preemption")
Signed-off-by: zihan zhou <15645113830zzh@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Tested-by: Vincent Guittot <vincent.guittot@linaro.org>
Link: https://lkml.kernel.org/r/20250208080850.16300-1-15645113830zzh@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>