Several functions called in rtw89_ops_start_ap() may fail to allocate
skb or fail to send H2C command to firmware, returning -ENOMEM or an
error code. Their return values are ignored, so subsequent commands
are executed with incorrect state.
Check the return values and propagate errors.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: a52e4f2ce0 ("rtw89: implement ieee80211_ops::start_ap and stop_ap")
Signed-off-by: Dmitry Morgun <d.morgun@ispras.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260629094452.8709-1-d.morgun@ispras.ru
Only the WiFi 6 chips need to initialize RF register when WoWLAN download
FW for some power save issue. Applying the same initialization flow to
WiFi 7 chips might trigger the error
'RF parameters exceed size. path=1, idx=1500.'.
This happens because normal mode uses rtw89_phy_config_rf_reg_v1(), which
skips registers with addresses below 0x100. However, WoWLAN mode uses
rtw89_phy_config_rf_reg_noio(), and WiFi 7 chips do not satisfy the
rtw89_chip_rf_v1() condition. As a result, more RF registers are
configured, causing the size overflow error.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260625061545.44808-11-pkshih@realtek.com
Some MLO APs expect WoWLAN ARP response frames to be transmitted as
QoS data frames and may discard frames that do not contain a QoS
Control field.
Add a QoS Control field and use the QoS Data subtype when generating
WoWLAN ARP responses for MLD vifs. Keep the existing frame format
unchanged for non-MLO connections.
This allows WoWLAN ARP responses to be accepted by MLO APs while
preserving compatibility with legacy APs.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260625061545.44808-10-pkshih@realtek.com
Currently, WoWLAN ARP replies for MLO stations use the link address in
the ARP hardware address fields.
As a result, peers may learn the link address from the ARP reply and
use it as the destination address for subsequent traffic. Some APs may
not forward frames addressed to the link address, causing connectivity
issues.
Use the MLD address instead when generating WoWLAN ARP replies so peers
learn the correct address for MLO stations.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260625061545.44808-9-pkshih@realtek.com
The link ID field in H2C command of LPS MLO common info is incorrectly
filled with the PHY index. Fix it with the target link ID.
Fixes: 20380a039d ("wifi: rtw89: phy: add H2C command to send detail RX gain and link parameters for PS mode")
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260625061545.44808-8-pkshih@realtek.com
On some platforms, refclk is not available up to 15 ms after entering
suspend. The delayed clock cause the hardware to detect falsely error
and trigger an unexpected hardware reset. Disable the phy error flag
related to refclk to fix it.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260625061545.44808-7-pkshih@realtek.com
Sniffer mode is enabled by default in the RX filter on Wi-Fi 7 chips,
which causes all packets to be received regardless of the ADDR_CAM
lookup result. This may result in unexpected packets being received.
Therefore, disable it by default.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260625061545.44808-6-pkshih@realtek.com
A special case is when C2H done ack has been completed, but the
corresponding packet offload response has not actually been received,
which causes the add packet offload to fail. In this state, firmware
treats the entry as added, so subsequent add requests for the same id
are rejected as duplicates. To recover from this, send a delete packet
offload H2C command to roll back the normal state. It has been tested and
verified to have no functional side effect.
Signed-off-by: Dian-Syuan Yang <dian_syuan0116@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260625061545.44808-5-pkshih@realtek.com
The UDM1 is user define message to record count of H2C command sent by
driver and received by firmware. Normally, this value should be zero.
Otherwise, throw a warning.
For the new chip RTL8922DE, its default value is not zero, causing a
warning at first time probe. Since this is a debug purpose and the
value will be set to zero right after this checking, lower the debug level.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260625061545.44808-4-pkshih@realtek.com
Currently active TX only finishes after ensuring PCIE and DMAC become idle.
However, the waiting time might be long. Since the packet is already
transmitted over the air, update the registers to finish active TX
immediately, regardless of the PCIE/DMAC status.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260625061545.44808-2-pkshih@realtek.com
The firmware 0.35.94.1 included several new features. Wi-Fi TX power
setting offload to firmware. Including dual BT / dual Wi-Fi MAC related
configurations.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260624033941.45918-10-pkshih@realtek.com
It's more closing to the original meaning. It is defined for rearranging
driver info index by firmware support version.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260624033941.45918-9-pkshih@realtek.com
In order to support external Zigbee/Thread/Bluetooth etc module,
the version 8 add the parameter for the case. And also update the
related configuration function.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260624033941.45918-8-pkshih@realtek.com
The incoming chip reserved several IO ports to coexist with the other
vendor's stand along chips. In order to configured them easier add the
structure.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260624033941.45918-7-pkshih@realtek.com
In order to support dual Bluetooth chip, move Bluetooth counters to BT
info. Because the two Bluetooth need to collect their own counters.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260624033941.45918-6-pkshih@realtek.com
This variable is for asking driver occupied Bluetooth traffic slot while
wifi is running at multi-port mode. Example like station + AP. The time
slot is separated by wifi driver under these wifi modes. And to ensure
Bluetooth performance, Coex will advice the Bluetooth slot length to
driver. And each MAC is able to run multi-port mode, so extend the
variable's index.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260624033941.45918-5-pkshih@realtek.com
Move wifi related counters to wifi main info, it is to facilitate
the after modification for dual MAC wifi structure.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260624033941.45918-4-pkshih@realtek.com
In order to compatible with single/dual Bluetooth structure in one branch,
offset the currently using BT info structure to BT-0.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260624033941.45918-3-pkshih@realtek.com
Wi-Fi can not reach LPS leave threshold while Wi-Fi only throughput
not good & Bluetooth share bandwidth. Add logic to let force leave
Wi-Fi LPS while Bluetooth profile exist. Update COEX version to 9.0.1.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260624033941.45918-2-pkshih@realtek.com
By default RTL8723D, RTL8703B, RTL8812A, RTL8821A, and RTL8814A are
configured to filter out all control frames except PS-Poll, even in
monitor mode.
Handle FIF_CONTROL in rtw_ops_configure_filter(). When it's set,
configure REG_RXFLTMAP1 to let all control frames through. When it's
unset, restore the original value. Because some drivers configure
REG_RXFLTMAP1 differently, keep track of its value in a new member of
struct rtw_hal.
Signed-off-by: Bitterblue Smith (S.E.A. Datentechnik GmbH) <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/2a52d718-9e46-47f2-84a1-d8e7b1ed89a8@gmail.com
rtl92du_tx_fill_desc() uses ieee80211_get_tid() to read the QoS TID
from the 802.11 header and then uses it as an index into
sta_entry->tids[]. ieee80211_get_tid() returns the low 4-bit QoS TID
value, so the result can be in the range 0..15.
rtlwifi only allocates MAX_TID_COUNT entries for sta_entry->tids[], and
MAX_TID_COUNT is 9. A QoS TID greater than 8 therefore indexes past the
aggregation state array. Keep the default RTL_AGG_STOP state for
out-of-range TIDs, matching rtl92cu_tx_fill_desc().
This issue was detected by our static analysis tool and confirmed by
manual audit. UBSAN validation for the same bug pattern reports an
array-index-out-of-bounds access with index 10 for type
'rtl_tid_data [9]'.
Fixes: 8321424134 ("wifi: rtlwifi: Add rtl8192du/trx.{c,h}")
Cc: stable@vger.kernel.org
Signed-off-by: Runyu Xiao <runyu.xiao@seu.edu.cn>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260620025632.46206-1-runyu.xiao@seu.edu.cn
rtw_pci_probe() allocates PCI resources through
rtw_pci_setup_resource() before it sets up NAPI. If
rtw_pci_napi_init() fails, the error path jumps straight to
err_pci_declaim and skips rtw_pci_destroy(), leaving the PCI
resources allocated by rtw_pci_setup_resource() behind.
Add a dedicated cleanup label for the NAPI setup failure path so probe
destroys the PCI resources.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing current
mainline kernels. The tool is still under development and is not yet
publicly available. Manual inspection confirms that the bug is still
present in v7.1-rc7.
An x86_64 allyesconfig build showed no new warnings. As we do not have a
suitable rtw88 PCI board to test with, no runtime testing was able to be
performed.
Fixes: d0bcb10e7b ("wifi: rtw88: Un-embed dummy device")
Cc: stable@vger.kernel.org
Signed-off-by: Dawei Feng <dawei.feng@seu.edu.cn>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260617013502.114057-1-dawei.feng@seu.edu.cn
Replace msleep() with fsleep(), because msleep() may oversleep
to as much as 20 ms when used for a 10 ms delay.
According to the kernel documentation, fsleep() is more suitable
and aligns better with modern kernel style.
Signed-off-by: Chen Jung Ku <ku.loong@gapp.nthu.edu.tw>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260613170434.23645-1-ku.loong@gapp.nthu.edu.tw
Replace "enable"/"disable" strings in ternary expressions
with the str_enable_disable() helper from <linux/string_choices.h>.
This covers the rfkill state log in rtw89_core_rfkill_poll() and
the DPK on/off log in _dpk_onoff().
No functional change intended.
Signed-off-by: Panagiotis Petrakopoulos <npetrakopoulos2003@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260612223012.504886-1-npetrakopoulos2003@gmail.com
BE_CCTL_INFO_W2_PRELOAD_ENABLE is for h2c->w2, not h2c->w1.
These will cause h2c->w1 wrong overlap by w2 and w2 not initialized.
Fixes: c73607b3a8 ("wifi: rtw89: fw: add CMAC H2C command to initialize default value for RTL8922D")
Signed-off-by: Wentao Guan <guanwentao@uniontech.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260611082021.46650-1-guanwentao@uniontech.com
Replace <= with < in the loop in query_phy_status_page1(). It was
processing data related to RF path C, which this chip doesn't have.
The only bad effect seems to be that the phy_info file in debugfs was
printing unexpected values for RF path C.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/9c4beb36-2954-4db0-844a-74ba5eacf21b@gmail.com
Replace <= with < in the loops in query_phy_status_page{0,1}(). They
were processing data related to RF path C, which this chip doesn't have.
The only bad effect seems to be that the phy_info file in debugfs was
printing unexpected values for RF path C.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/ee30b95f-bc68-4711-9b15-cf5fd23c3c48@gmail.com
rtl8723be hw_init() calls local_save_flags(flags) followed by
local_irq_enable(). Later, local_irq_restore(flags) is called.
This causes warnings from Lockdep on boot and modprobe,
as local_irq_restore(flags) should only be called while irqs are disabled.
The warning was introduced to detect this class of bug in [1].
With testing I found that all paths which call hw_init() have irqs
already enabled for rtl8723be.
Furthermore, the calls were originally added for the rtl8192ce
in commit f78bccd79b ("rtlwifi: rtl8192ce: Fix too long disable of IRQs")
before later being added to most other rtlwifi drivers.
Commit d3feae41a3 ("rtlwifi: Update power-save routines for 062814 driver")
then replaces the call to spin_lock_irqsave() before hw_init(),
and thus the codepath which caused irqs to be disabled in hw_init and
prompted the original commit has been removed.
The same irq save/restore pattern is also present in the hw_init() of
rtl8192ce, rtl8723ae, rtl8188ee, rtl8192se and rtl8192cu,
however I don't have the hardware to test them,
so I did not include them in my changes.
Tested on a Razer Blade 14 2017.
Example of output from Lockdep prior to fix:
raw_local_irq_restore() called with IRQs enabled
...
Call Trace:
<TASK>
rtl8723be_hw_init+0x5992/0x7220 [rtl8723be]
? static_obj+0x61/0xa0
rtl_pci_start+0x222/0x5c0 [rtl_pci]
rtl_op_start+0x128/0x1a0 [rtlwifi]
? __kasan_check_read+0x11/0x20
drv_start+0x16c/0x550 [mac80211]
...
irq event stamp: 887679
hardirqs last enabled at (887689): [<ffffffff96511170>] __up_console_sem+0x90/0xa0
hardirqs last disabled at (887698): [<ffffffff96511155>] __up_console_sem+0x75/0xa0
softirqs last enabled at (887670): [<ffffffff962f4675>] __irq_exit_rcu+0x175/0x2f0
softirqs last disabled at (887649): [<ffffffff962f4675>] __irq_exit_rcu+0x175/0x2f0
---[ end trace 0000000000000000 ]---
[1] https://lore.kernel.org/all/20210111153707.10071-1-mark.rutland@arm.com/
Signed-off-by: William Hansen-Baird <william.hansen.baird@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260609095359.2964193-1-william.hansen.baird@gmail.com
This > comparison should be >= to avoid an out of bounds access.
Fixes: 419ed7f4a0 ("wifi: rtw89: debug: extend bb_info with TX status and PER")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/aia25i0ds3B6QF6c@stanley.mountain
The format of scan offload v2 is to extend fields to consider channel
noise as a factor to adjust dwell time of certain channels. Leave empty
for now to ignore this factor.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260525070735.27659-3-pkshih@realtek.com
The firmware features including version of command/event format are
maintained by this table, which enables features by firmware version.
Define the first feature set accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260525070735.27659-2-pkshih@realtek.com
device removal, along with documentation fixes and minor AMD driver
cleanups.
-----BEGIN PGP SIGNATURE-----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=V3cD
-----END PGP SIGNATURE-----
Merge tag 'ntb-7.2' of https://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"An EPF bug fix to prevent an invalid unmap during device removal,
along with documentation fixes and minor AMD driver cleanups"
* tag 'ntb-7.2' of https://github.com/jonmason/ntb:
ntb: amd: Use named initializer for pci_device_id::driver_data
NTB: fix kernel-doc warnings in ntb.h
NTB: epf: Avoid pci_iounmap() with offset when PEER_SPAD and CONFIG share BAR
ntb_hw_amd: Fix incorrect debug message in link disable path
- Updates to Synaptics RMI4 driver to fix potential OOB accesses in
F30 and F3A keymap handling
- A workaround in Synaptics RMI4 to tolerate buggy firmware on some
touchpads (e.g. ThinkPad T14 Gen 1) that report incomplete register
descriptor structures, preventing probe failures
- A revert of an incorrect register descriptor address calculation in
Synaptics RMI4 driver
- A fix for a regression in HP GSC PS/2 (gscps2) driver where the
receive buffer write index was not advanced, leaving keyboard and
mouse unusable.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQST2eWILY88ieB2DOtAj56VGEWXnAUCakCsxwAKCRBAj56VGEWX
nCICAQDSgfrAi+4SqTb92EjtdQO+ypluS42mKO75LTitJcS8dAEA1iKmdss8mGww
c4ai4W+UFxori7IqgkoQ7LfaPTOWlA0=
=QP4c
-----END PGP SIGNATURE-----
Merge tag 'input-for-v7.2-rc0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull more input updates from Dmitry Torokhov:
- Updates to Synaptics RMI4 driver to fix potential OOB accesses in F30
and F3A keymap handling
- A workaround in Synaptics RMI4 to tolerate buggy firmware on some
touchpads (e.g. ThinkPad T14 Gen 1) that report incomplete register
descriptor structures, preventing probe failures
- A revert of an incorrect register descriptor address calculation in
Synaptics RMI4 driver
- A fix for a regression in HP GSC PS/2 (gscps2) driver where the
receive buffer write index was not advanced, leaving keyboard and
mouse unusable.
* tag 'input-for-v7.2-rc0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: gscps2 - advance receive buffer write index
Input: rmi4 - tolerate short register descriptor structure
Revert "Input: rmi4 - fix register descriptor address calculation"
Input: synaptics-rmi4 - bound the F30 keymap to the GPIO/LED count
Input: synaptics-rmi4 - bound the F3A keymap to the GPIO count
Two more fixes that I managed to put into the public branch merged into
next before my first PR but missed to include them in it. The first
change is a relevant change that fixes misconfigurations due to a
variable overflow. The 2nd is only cosmetic but very obviously an
improvement.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEP4GsaTp6HlmJrf7Tj4D7WH0S/k4FAmpAE2gACgkQj4D7WH0S
/k7tnAgAsjkBQWoav1MF8kyVzew+iIuVvBrtUPimzeMs2gzwC1czi/TPKCvZxGND
XaPESmf51lC9AZuFd/2Wfvb2GydxA/wmsbVB0Q6ZBwLtS6/L4yiv3DpYN2to9yWN
QvVHeVCBdSbMHOQXdG0iFbhMiLyUX5YwCwyZT2cuVUHb4gvNLuDuKbgSXX9Odh1R
/p9C0afNMbdxuj2yRy+S8CM5Rl5v4yfBw6cswKX6w3uA+LnvksWuC8og7tEfFa/F
Vdwy4csWeKHGm7jEP9o6iSlWYy+DMKf5Llop+yFLZV6Db6AXMlEpNOXJsGxEv95y
qMTQFCGhepNWqVuUDDOOeUs60Asjpg==
=0WY9
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-7.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux
Pull pwm fixes from Uwe Kleine-König:
"Two more fixes that I managed to put into the public branch merged
into next before my first pull request but missed to include them in
it.
The first change is a relevant change that fixes misconfigurations due
to a variable overflow. The second is only cosmetic but very obviously
an improvement"
* tag 'pwm/for-7.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux:
pwm: rzg2l-gpt: Add missing newlines to dev_err_probe() messages
pwm: rzg2l-gpt: Fix period_ticks type from u32 to u64
Fixes:
- fbcon: fix NULL pointer dereference for a console without vc_data [Ian Bridges]
- fbdev: fix fb_new_modelist to prevent null-ptr-deref in fb_videomode_to_var [Ian Bridges]
Fixes in failure paths:
- pm2fb: unwind write-cache setting on probe failure [Haoxiang Li]
- goldfishfb: fail pan display on base-update timeout [Pengpeng Hou]
- viafb: return error on DMA copy time-out [Pengpeng Hou]
- fbcon: fix out-of-bounds read in error path of fbcon_do_set_font() [Mingyu Wang]
- fbdev: fix modelist use-after-free in store_modes() [Ian Bridges]
Code cleanup:
- vga16fb: clean up platform_device_id table [Uwe Kleine-König]
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCakAKnwAKCRD3ErUQojoP
X27+AQCPvMJUMScjO1dlGKkPnnIFiOWCU6AW1aM2m6T+qWrCTQEAnNi5CCI3JiLi
6NCcyPm7/4R6tSXDm+UcWJ5tyzaNvww=
=EBHb
-----END PGP SIGNATURE-----
Merge tag 'fbdev-for-7.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull more fbdev updates from Helge Deller:
"Fixes for generic fbdev & fbcon code for the handling of modelists
and preventing a potential NULL ptr dereference in the console code.
Fix missed cleanups in the error path of various fbdev drivers.
And Uwe Kleine-König contributed a cleanup patch to use named
initializers in the vga16fb driver"
* tag 'fbdev-for-7.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbdev: Fix fb_new_modelist to prevent null-ptr-deref in fb_videomode_to_var
fbcon: fix NULL pointer dereference for a console without vc_data
fbdev: fix use-after-free in store_modes()
fbdev: viafb: return an error when DMA copy times out
fbdev: goldfishfb: fail pan display on base-update timeout
fbdev: fbcon: fix out-of-bounds read in err_out of fbcon_do_set_font()
fbdev: pm2fb: unwind WC setup on probe failure
fbdev: vga16fb: Drop unused assignment of platform_device_id driver data
A collection of small bug fixes accumulated over the last week.
Most are device-specific fixes while there are a few core fixes as
well.
Here are the highlights:
ALSA Core:
- A fix for an uninitialised heap leak in ALSA sequencer core
- A fix for error handling/resource leak in compress-offload API
USB-audio:
- A teardown-ordering fix in USB MIDI 2.0 to prevent use-after-free
- Bounds and length checks for packet data in Native Instruments caiaq
/ Traktor Kontrol input parsers
- Avoidance of expensive kobject path lookups in DualSense controller
matches
- Robustness/memory leak fixes for Qualcomm USB offload driver
- Focusrite Control Protocol (FCP) NULL-pointer dereference fix and a
new device quirk (ISA C8X)
- Device-specific quirks for Yamaha CDS3000 and SC13A
HD-Audio:
- A bunch of quirks and mute/mic-mute LED fixups for various laptops
(Acer, Clevo, Lenovo, HP)
ASoC & SoundWire:
- Avoid failing card registration if the device_link creation fails
- A workaround for SoundWire randconfig build failures by making
helper functions static inline
- Corrected MCLK reference validation for CS530x codecs
- Clean up of untested, problematic guard() macro replacements in
Rockchip SAI driver
- Fix for eDMA maxburst misalignment with channel count in Freescale
ASRC
- Miscellaneous hardware-specific fixes (qcom, rt5650, tlv320aic3x,
tas2781/3)
Others:
- Bounds and length checks for packet data in Apple iSight
-----BEGIN PGP SIGNATURE-----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=hJ5w
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small bug fixes accumulated over the last week.
Most are device-specific fixes while there are a few core fixes as
well.
Here are the highlights:
ALSA Core:
- A fix for an uninitialised heap leak in ALSA sequencer core
- A fix for error handling/resource leak in compress-offload API
USB-audio:
- A teardown-ordering fix in USB MIDI 2.0 to prevent use-after-free
- Bounds and length checks for packet data in Native Instruments
caiaq / Traktor Kontrol input parsers
- Avoidance of expensive kobject path lookups in DualSense controller
matches
- Robustness/memory leak fixes for Qualcomm USB offload driver
- Focusrite Control Protocol (FCP) NULL-pointer dereference fix and a
new device quirk (ISA C8X)
- Device-specific quirks for Yamaha CDS3000 and SC13A
HD-Audio:
- A bunch of quirks and mute/mic-mute LED fixups for various laptops
(Acer, Clevo, Lenovo, HP)
ASoC & SoundWire:
- Avoid failing card registration if the device_link creation fails
- A workaround for SoundWire randconfig build failures by making
helper functions static inline
- Corrected MCLK reference validation for CS530x codecs
- Clean up of untested, problematic guard() macro replacements in
Rockchip SAI driver
- Fix for eDMA maxburst misalignment with channel count in Freescale
ASRC
- Miscellaneous hardware-specific fixes (qcom, rt5650, tlv320aic3x,
tas2781/3)
Others:
- Bounds and length checks for packet data in Apple iSight"
* tag 'sound-fix-7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (46 commits)
ALSA: FCP: Fix NULL pointer dereference in interface lookup
ALSA: hda/realtek: Update Acer Nitro ANV15-41 quirk to enable mute LED
ASoC: fsl_asrc_dma: fix eDMA maxburst misalignment with channel count
ASoC: codecs: pcm512x: only print info once on no sclk
ASoC: tas2781: Update default register address to TAS2563
ALSA: firewire: isight: bound the sample count to the packet payload
ALSA: usb-audio: qcom: Free QMI handle
ALSA: hda: Add Lenovo Legion 7i 16IAX7 17AA3874 quirk
ALSA: usb-audio: avoid kobject path lookup in DualSense match
ALSA: hda/realtek: Add quirk for Acer Nitro ANV15-41
ASoC: soc-core: Don't fail if device_link could not be created
ASoC: rockchip: rockchip_sai: #include <linux/platform_device.h> explicitly
ALSA: seq: Fix uninitialised heap leak in snd_seq_event_dup()
ASoC: rt5575: Use __le32 for SPI burst write address
ASoC: tas2783: Update loaded firmware names to linux-firmware 20260519
ASoC: SDCA: Validate written enum value in ge_put_enum_double()
ASoC: realtek: Add back local call to sdw_show_ping_status()
ASoC: ti: Add back local call to sdw_show_ping_status()
ASoC: max98373: Add back local call to sdw_show_ping_status()
ASoC: es9356: Add back local call to sdw_show_ping_status()
...
Subsystem:
- add rtc_read_next_alarm() to read next expiring timer
Drivers:
- ds1307: handle OSF for ds1337/ds1339/ds3231, add clock provider for ds1307,
fix wday for rx8130
- m41t93: DT support, alarm, clock provider, watchdog support
- mv: add suspend/resume support for wakeup
- pcap: remove driver
- renesas-rtca3: many fixes
-----BEGIN PGP SIGNATURE-----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=SCOZ
-----END PGP SIGNATURE-----
Merge tag 'rtc-7.2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Most of the work and improvements are for features of the m41t93.
The ds1307 also gets support for OSF (Oscillator Stop Flag) for
new variants.
The pcap driver is being removed as the Motorola EZX support was
removed a while ago.
Subsystem:
- add rtc_read_next_alarm() to read next expiring timer
Drivers:
- ds1307: handle OSF for ds1337/ds1339/ds3231, add clock provider for
ds1307, fix wday for rx8130
- m41t93: DT support, alarm, clock provider, watchdog support
- mv: add suspend/resume support for wakeup
- pcap: remove driver
- renesas-rtca3: many fixes"
* tag 'rtc-7.2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (36 commits)
rtc: ds1307: update reference to removed CONFIG_RTC_DRV_DS1307_HWMON
platform/x86: amd-pmc: Fix S0i3 wakeup with alarmtimer
rtc: s35390a: fix typo in comment
rtc: cmos: unregister HPET IRQ handler on probe failure
rtc: ds1307: Fix off-by-one issue with wday for rx8130
dt-bindings: rtc: ds1307: Add epson,rx8901
rtc: bq32000: add delay between RTC reads
rtc: m41t93: Add watchdog support
rtc: m41t93: Add square wave clock provider support
rtc: m41t93: Add alarm support
rtc: m41t93: migrate to regmap api for register access
rtc: m41t93: add device tree support
dt-bindings: rtc: Add ST m41t93
rtc: ds1307: add support for clock provider in ds1307
rtc: mv: add suspend/resume support for wakeup
rtc: aspeed: add AST2700 compatible
dt-bindings: rtc: add ASPEED AST2700 compatible
rtc: interface: fix typos in rtc_handle_legacy_irq() documentation
rtc: msc313: fix NULL deref in shared IRQ handler at probe
rtc: remove unused pcap driver
...
- Fix a bug where in a specific edge case, file contents en/decryption
could be done with the wrong data unit size.
- Fix the data structure used for keeping track of users that have added
an fscrypt key to be a simple list instead of a 'struct key' keyring.
This fixes issues such as a lockdep report found by syzbot and
possible unintended interactions with the keyctl() system calls.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQSacvsUNc7UX4ntmEPzXCl4vpKOKwUCaj8bBhQcZWJpZ2dlcnNA
a2VybmVsLm9yZwAKCRDzXCl4vpKOKyhIAP47lR+H783gopiz10Z7dwLQr2EHMfZ1
NcU7Zfq++AzZRQD/Tvv9/daqSh0OJTDNkBskSgVj6z7sRlQVNHY0wrD+QwE=
=LWES
-----END PGP SIGNATURE-----
Merge tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/linux
Pull fscrypt fixes from Eric Biggers:
- Fix a bug where in a specific edge case, file contents en/decryption
could be done with the wrong data unit size
- Fix the data structure used for keeping track of users that have
added an fscrypt key to be a simple list instead of a 'struct key'
keyring
This fixes issues such as a lockdep report found by syzbot and
possible unintended interactions with the keyctl() system calls
* tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/linux:
fscrypt: Replace mk_users keyring with simple list
fscrypt: Fix key setup in edge case with multiple data unit sizes
Commit 44f9200699 ("Input: gscps2 - use guard notation when
acquiring spinlock") moved the receive loop into gscps2_read_data()
and gscps2_report_data().
While moving the code, it preserved the writes to
buffer[ps2port->append], but omitted the following producer index
update from the original loop:
ps2port->append = (ps2port->append + 1) & BUFFER_SIZE;
As a result, append never advances. Since gscps2_report_data() only
reports bytes while act != append, the receive buffer always appears
empty and no keyboard or mouse data reaches the serio core.
Restore the omitted index update.
Fixes: 44f9200699 ("Input: gscps2 - use guard notation when acquiring spinlock")
Cc: stable@vger.kernel.org # 6.13+
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Link: https://patch.msgid.link/460B5655BA580C60+20260624094739.850306-1-raoxu@uniontech.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some touchpads (e.g. ThinkPad T14 Gen 1) have buggy firmware that reports
a register descriptor structure size that is too small for the number of
registers it claims to have in the presence map. The remaining bytes in
the structure are 0, which with the new strict bounds checking causes the
parser to fail with -EIO, aborting the device probe.
Tolerate such short reads by dropping the remaining (unparseable or
0-size) registers from the list instead of failing the probe,
preventing the driver from trying to use them.
Fixes: 0adb483fbf ("Input: rmi4 - refactor register descriptor parsing")
Reported-by: Barry K. Nathan <barryn@pobox.com>
Tested-by: Barry K. Nathan <barryn@pobox.com>
Cc: stable@vger.kernel.org
Assisted-by: Antigravity:gemini-3.5-flash
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The register descriptor presence register is a packet register, which
means its bytes share a single RMI address. It does not occupy
consecutive addresses, and the register structure that follows it
is located at the next RMI address (presence_address + 1), not
(presence_address + presence_size).
Revert the incorrect address calculation introduced in commit
a98518e724.
Reported-by: "Barry K. Nathan" <barryn@pobox.com>
Tested-by: "Barry K. Nathan" <barryn@pobox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current list initialisation depends on the well hidden two zeros in
the PCI_VDEVICE macro. Instead use a named initialisation that is more
robust and easier to understand.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Correct a function name and function parameter name to avoid
kernel-doc warnings:
Warning: include/linux/ntb.h:575 expecting prototype for
ntb_default_port_count(). Prototype was for ntb_default_peer_port_count()
instead
Warning: include/linux/ntb.h:590 function parameter 'pidx' not
described in 'ntb_default_peer_port_number'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
When BAR_PEER_SPAD and BAR_CONFIG share one PCI BAR, the module teardown
path ends up calling pci_iounmap() on the same iomem with some offset,
which is unnecessary and triggers a kernel warning like the following:
Trying to vunmap() nonexistent vm area (0000000069a5ffe8)
WARNING: mm/vmalloc.c:3470 at vunmap+0x58/0x68, CPU#5: modprobe/2937
[...]
Call trace:
vunmap+0x58/0x68 (P)
iounmap+0x34/0x48
pci_iounmap+0x2c/0x40
ntb_epf_pci_remove+0x44/0x80 [ntb_hw_epf]
pci_device_remove+0x48/0xf8
device_remove+0x50/0x88
device_release_driver_internal+0x1c8/0x228
driver_detach+0x50/0xb0
bus_remove_driver+0x74/0x100
driver_unregister+0x34/0x68
pci_unregister_driver+0x34/0xa0
ntb_epf_pci_driver_exit+0x14/0xfe0 [ntb_hw_epf]
[...]
Fix it by unmapping only when PEER_SPAD and CONFIG use difference bars.
Cc: stable@vger.kernel.org
Fixes: e75d5ae8ab ("NTB: epf: Allow more flexibility in the memory BAR map method")
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Koichiro Den <den@valinux.co.jp>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
