[ Upstream commit 368e4663c5 ]
"assigned" and "assigned->name" are allocated in snd_mixer_oss_proc_write()
using kmalloc() and kstrdup(), so there is no point in using kfree_const()
to free these resources.
Switch to the more standard kfree() to free these resources.
This could avoid a memory leak.
Fixes: 454f5ec1d2 ("ALSA: mixer: oss: Constify snd_mixer_oss_assign_table definition")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://patch.msgid.link/63ac20f64234b7c9ea87a7fa9baf41e8255852f7.1727374631.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65e6a2773d ]
Remove locks calls in usbtv_video_free() because
are useless and may led to a deadlock as reported here:
https://syzkaller.appspot.com/x/bisect.txt?x=166dc872180000
Also remove usbtv_stop() call since it will be called when
unregistering the device.
Before 'c838530d23' this issue would only be noticed if you
disconnect while streaming and now it is noticeable even when
disconnecting while not streaming.
Fixes: c838530d23 ("media: media videobuf2: Be more flexible on the number of queue stored buffers")
Fixes: f3d27f34fd ("[media] usbtv: Add driver for Fushicai USBTV007 video frame grabber")
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: fix minor spelling mistake in log message]
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d4a1adbed ]
In the event that the I2C bus was powered down when the I2C controller
driver loads, or some spurious pulses occur on the I2C bus, it's
possible that the controller detects a spurious I2C "start" condition.
In this situation it may continue to report the bus is busy indefinitely
and block the controller from working.
The "single-master" DT flag can be specified to disable bus busy checks
entirely, but this may not be safe to use in situations where other I2C
masters may potentially exist.
In the event that the controller reports "bus busy" for too long when
starting a transaction, we can try reinitializing the controller to see
if the busy condition clears. This allows recovering from this scenario.
Fixes: e1d5b6598c ("i2c: Add support for Xilinx XPS IIC Bus Interface")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Cc: <stable@vger.kernel.org> # v2.6.34+
Reviewed-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee1691d0ae ]
xiic_start_xfer can fail for different reasons:
- EBUSY: bus is busy or i2c messages still in tx_msg or rx_msg
- ETIMEDOUT: timed-out trying to clear the RX fifo
- EINVAL: wrong clock settings
Both EINVAL and ETIMEDOUT will currently print a specific error
message followed by a generic one, for example:
Failed to clear rx fifo
Error xiic_start_xfer
however EBUSY will simply output the generic message:
Error xiic_start_xfer
which is not really helpful.
This commit adds a new error message when a busy condition is detected
and also removes the generic message since it does not provide any
relevant information to the user.
Signed-off-by: Marc Ferland <marc.ferland@sonatest.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Stable-dep-of: 1d4a1adbed ("i2c: xiic: Try re-initialization on bus busy timeout")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d663d93bb4 ]
The xiic_xfer() function gets a runtime PM reference when the function is
entered. This reference is released when the function is exited. There is
currently one error path where the function exits directly, which leads to
a leak of the runtime PM reference.
Make sure that this error path also releases the runtime PM reference.
Fixes: fdacc3c740 ("i2c: xiic: Switch from waitqueue to completion")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: 1d4a1adbed ("i2c: xiic: Try re-initialization on bus busy timeout")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 294b29f154 ]
In case the XIIC does TX/RX transfer, make sure no other kernel thread
can start another TX transfer at the same time. This could happen since
the driver only checks tx_msg for being non-NULL and returns -EBUSY in
that case, however it is necessary to check also rx_msg for the same.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: 1d4a1adbed ("i2c: xiic: Try re-initialization on bus busy timeout")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fdacc3c740 ]
There will never be threads queueing up in the xiic_xmit(), use
completion synchronization primitive to wait for the interrupt
handler thread to complete instead as it is much better fit and
there is no need to overload it for this purpose.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: 1d4a1adbed ("i2c: xiic: Try re-initialization on bus busy timeout")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c119e7d00c ]
The tx_msg is set from multiple places, sometimes without locking,
which fall apart on any SMP system. Only ever access tx_msg inside
the driver mutex.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: 1d4a1adbed ("i2c: xiic: Try re-initialization on bus busy timeout")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8beee4d8de ]
In sctp_listen_start() invoked by sctp_inet_listen(), it should set the
sk_state back to CLOSED if sctp_autobind() fails due to whatever reason.
Otherwise, next time when calling sctp_inet_listen(), if sctp_sk(sk)->reuse
is already set via setsockopt(SCTP_REUSE_PORT), sctp_sk(sk)->bind_hash will
be dereferenced as sk_state is LISTENING, which causes a crash as bind_hash
is NULL.
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:sctp_inet_listen+0x7f0/0xa20 net/sctp/socket.c:8617
Call Trace:
<TASK>
__sys_listen_socket net/socket.c:1883 [inline]
__sys_listen+0x1b7/0x230 net/socket.c:1894
__do_sys_listen net/socket.c:1902 [inline]
Fixes: 5e8f3f703a ("sctp: simplify sctp listening code")
Reported-by: syzbot+f4e0f821e3a3b7cee51d@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://patch.msgid.link/a93e655b3c153dc8945d7a812e6d8ab0d52b7aa0.1727729391.git.lucien.xin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4a14f6d9d ]
Regression Description:
Depending on the options specified for the GRE tunnel device, small
packets may be dropped. This occurs because the pskb_network_may_pull
function fails due to the packet's insufficient length.
For example, if only the okey option is specified for the tunnel device,
original (before encapsulation) packets smaller than 28 bytes (including
the IPv4 header) will be dropped. This happens because the required
length is calculated relative to the network header, not the skb->head.
Here is how the required length is computed and checked:
* The pull_len variable is set to 28 bytes, consisting of:
* IPv4 header: 20 bytes
* GRE header with Key field: 8 bytes
* The pskb_network_may_pull function adds the network offset, shifting
the checkable space further to the beginning of the network header and
extending it to the beginning of the packet. As a result, the end of
the checkable space occurs beyond the actual end of the packet.
Instead of ensuring that 28 bytes are present in skb->head, the function
is requesting these 28 bytes starting from the network header. For small
packets, this requested length exceeds the actual packet size, causing
the check to fail and the packets to be dropped.
This issue affects both locally originated and forwarded packets in
DMVPN-like setups.
How to reproduce (for local originated packets):
ip link add dev gre1 type gre ikey 1.9.8.4 okey 1.9.8.4 \
local <your-ip> remote 0.0.0.0
ip link set mtu 1400 dev gre1
ip link set up dev gre1
ip address add 192.168.13.1/24 dev gre1
ip neighbor add 192.168.13.2 lladdr <remote-ip> dev gre1
ping -s 1374 -c 10 192.168.13.2
tcpdump -vni gre1
tcpdump -vni <your-ext-iface> 'ip proto 47'
ip -s -s -d link show dev gre1
Solution:
Use the pskb_may_pull function instead the pskb_network_may_pull.
Fixes: 80d875cfc9 ("ipv4: ip_gre: Avoid skb_pull() failure in ipgre_xmit()")
Signed-off-by: Anton Danilov <littlesmilingcloud@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20240924235158.106062-1-littlesmilingcloud@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c1b56671b ]
Increase the timeout for checking the busy bit of the VLAN Tag register
from 10µs to 500ms. This change is necessary to accommodate scenarios
where Energy Efficient Ethernet (EEE) is enabled.
Overnight testing revealed that when EEE is active, the busy bit can
remain set for up to approximately 300ms. The new 500ms timeout provides
a safety margin.
Fixes: ed64639bc1 ("net: stmmac: Add support for VLAN Rx filtering")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://patch.msgid.link/20240924205424.573913-1-shenwei.wang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 929d43421e ]
The stmmac has the possibility to automatically strip the padding/FCS for IEEE
802.3 type frames. This feature is enabled conditionally. Therefore, the stmmac
receive path has to have a determination logic whether the FCS has to be
stripped in software or not.
In fact, for DSA this ACS feature is disabled and the determination logic
doesn't check for it properly. For instance, when using DSA in combination with
an older stmmac (pre version 4), the FCS is not stripped by hardware or software
which is problematic.
So either add another check for DSA to the fast path or simply disable ACS
feature completely. The latter approach has been chosen, because most of the
time the FCS is stripped in software anyway and it removes conditionals from the
receive fast path.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/87v8q8jjgh.fsf@kurt/
Link: https://lore.kernel.org/r/20220905130155.193640-1-kurt@linutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: 4c1b56671b ("net: stmmac: dwmac4: extend timeout for VLAN Tag register busy bit check")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f296e782f ]
This bug report came up when we were testing the device driver
by fuzzing. It shows that buf1_len can get underflowed and be
0xfffffffc (4294967292).
This bug is triggerable with a compromised/malfunctioning device.
We found the bug through QEMU emulation tested the patch with
emulation. We did NOT test it on real hardware.
Attached is the bug report by fuzzing.
BUG: KASAN: use-after-free in stmmac_napi_poll_rx+0x1c08/0x36e0 [stmmac]
Read of size 4294967292 at addr ffff888016358000 by task ksoftirqd/0/9
CPU: 0 PID: 9 Comm: ksoftirqd/0 Tainted: G W 5.6.0 #1
Call Trace:
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x16/0x200
? stmmac_napi_poll_rx+0x1c08/0x36e0 [stmmac]
? stmmac_napi_poll_rx+0x1c08/0x36e0 [stmmac]
__kasan_report.cold+0x37/0x7c
? stmmac_napi_poll_rx+0x1c08/0x36e0 [stmmac]
kasan_report+0xe/0x20
check_memory_region+0x15a/0x1d0
memcpy+0x20/0x50
stmmac_napi_poll_rx+0x1c08/0x36e0 [stmmac]
? stmmac_suspend+0x850/0x850 [stmmac]
? __next_timer_interrupt+0xba/0xf0
net_rx_action+0x363/0xbd0
? call_timer_fn+0x240/0x240
? __switch_to_asm+0x40/0x70
? napi_busy_loop+0x520/0x520
? __schedule+0x839/0x15a0
__do_softirq+0x18c/0x634
? takeover_tasklets+0x5f0/0x5f0
run_ksoftirqd+0x15/0x20
smpboot_thread_fn+0x2f1/0x6b0
? smpboot_unregister_percpu_thread+0x160/0x160
? __kthread_parkme+0x80/0x100
? smpboot_unregister_percpu_thread+0x160/0x160
kthread+0x2b5/0x3b0
? kthread_create_on_node+0xd0/0xd0
ret_from_fork+0x22/0x40
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 4c1b56671b ("net: stmmac: dwmac4: extend timeout for VLAN Tag register busy bit check")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab9a9a9e96 ]
One path takes care of SKB_GSO_DODGY, assuming
skb->len is bigger than hdr_len.
virtio_net_hdr_to_skb() does not fully dissect TCP headers,
it only make sure it is at least 20 bytes.
It is possible for an user to provide a malicious 'GSO' packet,
total length of 80 bytes.
- 20 bytes of IPv4 header
- 60 bytes TCP header
- a small gso_size like 8
virtio_net_hdr_to_skb() would declare this packet as a normal
GSO packet, because it would see 40 bytes of payload,
bigger than gso_size.
We need to make detect this case to not underflow
qdisc_skb_cb(skb)->pkt_len.
Fixes: 1def9238d4 ("net_sched: more precise pkt_len computation")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45c0de18ff ]
When applying padding, the buffer is not zeroed, which results in memory
disclosure. The mentioned data is observed on the wire. This patch uses
skb_put_padto() to pad Ethernet frames properly. The mentioned function
zeroes the expanded buffer.
In case the packet cannot be padded it is silently dropped. Statistics
are also not incremented. This driver does not support statistics in the
old 32-bit format or the new 64-bit format. These will be added in the
future. In its current form, the patch should be easily backported to
stable versions.
Ethernet MACs on Amazon-SE and Danube cannot do padding of the packets
in hardware, so software padding must be applied.
Fixes: 504d4721ee ("MIPS: Lantiq: Add ethernet driver")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20240923214949.231511-2-olek2@wp.pl
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b1ab46059 ]
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable when request IRQ.
Fixes: bb7f4f0bce ("btmrvl: add platform specific wakeup interrupt support")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09573b1cc7 ]
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable when request IRQ.
Fixes: 8c6ad9cc51 ("ieee802154: Add NXP MCR20A IEEE 802.15.4 transceiver driver")
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/20240911094234.1922418-1-ruanjinjie@huawei.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f25389e779 ]
In mlx5e_tir_builder_alloc() kvzalloc() may return NULL
which is dereferenced on the next line in a reference
to the modify field.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: a6696735d6 ("net/mlx5e: Convert TIR to a dedicated object")
Signed-off-by: Elena Salomatkina <esalomatkina@ispras.ru>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec79315589 ]
Collecting crdump involves reading vsc registers from pci config space
of mlx device, which can take long time to complete. This might result
in starving other threads waiting to run on the cpu.
Numbers I got from testing ConnectX-5 Ex MCX516A-CDAT in the lab:
- mlx5_vsc_gw_read_block_fast() was called with length = 1310716.
- mlx5_vsc_gw_read_fast() reads 4 bytes at a time. It was not used to
read the entire 1310716 bytes. It was called 53813 times because
there are jumps in read_addr.
- On average mlx5_vsc_gw_read_fast() took 35284.4ns.
- In total mlx5_vsc_wait_on_flag() called vsc_read() 54707 times.
The average time for each call was 17548.3ns. In some instances
vsc_read() was called more than one time when the flag was not set.
As expected the thread released the cpu after 16 iterations in
mlx5_vsc_wait_on_flag().
- Total time to read crdump was 35284.4ns * 53813 ~= 1.898s.
It was seen in the field that crdump can take more than 5 seconds to
complete. During that time mlx5_vsc_wait_on_flag() did not release the
cpu because it did not complete 16 iterations. It is believed that pci
config reads were slow. Adding cond_resched() every 128 register read
improves the situation. In the common case the, crdump takes ~1.8989s,
the thread yields the cpu every ~4.51ms. If crdump takes ~5s, the thread
yields the cpu every ~18.0ms.
Fixes: 8b9d8baae1 ("net/mlx5: Add Crdump support")
Reviewed-by: Yuanyuan Zhong <yzhong@purestorage.com>
Signed-off-by: Mohamed Khalfella <mkhalfella@purestorage.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2bcae12c79 ]
Remove the erroneous unmap in case no DMA mapping was established
The multi-packet WQE transmit code attempts to obtain a DMA mapping for
the skb. This could fail, e.g. under memory pressure, when the IOMMU
driver just can't allocate more memory for page tables. While the code
tries to handle this in the path below the err_unmap label it erroneously
unmaps one entry from the sq's FIFO list of active mappings. Since the
current map attempt failed this unmap is removing some random DMA mapping
that might still be required. If the PCI function now presents that IOVA,
the IOMMU may assumes a rogue DMA access and e.g. on s390 puts the PCI
function in error state.
The erroneous behavior was seen in a stress-test environment that created
memory pressure.
Fixes: 5af75c747e ("net/mlx5e: Enhanced TX MPWQE for SKBs")
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Acked-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit addf89774e ]
If REGMAP_SPI is m and IEEE802154_MCR20A is y,
mcr20a.c:(.text+0x3ed6c5b): undefined reference to `__devm_regmap_init_spi'
ld: mcr20a.c:(.text+0x3ed6cb5): undefined reference to `__devm_regmap_init_spi'
Select REGMAP_SPI for IEEE802154_MCR20A to fix it.
Fixes: 8c6ad9cc51 ("ieee802154: Add NXP MCR20A IEEE 802.15.4 transceiver driver")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/20240909131740.1296608-1-ruanjinjie@huawei.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c08dfb1b49 ]
When doing the direct-io reads it will also try to mark pages dirty,
but for the read path it won't hold the Fw caps and there is case
will it get the Fw reference.
Fixes: 5dda377cf0 ("ceph: set i_head_snapc when getting CEPH_CAP_FILE_WR reference")
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Patrick Donnelly <pdonnell@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc09f007ca ]
During noirq suspend phase the Raspberry Pi power driver suffer of
firmware property timeouts. The reason is that the IRQ of the underlying
BCM2835 mailbox is disabled and rpi_firmware_property_list() will always
run into a timeout [1].
Since the VideoCore side isn't consider as a wakeup source, set the
IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled
during suspend-resume cycle.
[1]
PM: late suspend of devices complete after 1.754 msecs
WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128
rpi_firmware_property_list+0x204/0x22c
Firmware transaction 0x00028001 timeout
Modules linked in:
CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17
Hardware name: BCM2835
Call trace:
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x34/0x44
dump_stack_lvl from __warn+0x88/0xec
__warn from warn_slowpath_fmt+0x7c/0xb0
warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c
rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c
rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0
rpi_firmware_set_power from _genpd_power_off+0xe4/0x148
_genpd_power_off from genpd_sync_power_off+0x7c/0x11c
genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0
genpd_finish_suspend from dpm_run_callback+0x78/0xd0
dpm_run_callback from device_suspend_noirq+0xc0/0x238
device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168
dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac
suspend_devices_and_enter from pm_suspend+0x254/0x2e4
pm_suspend from state_store+0xa8/0xd4
state_store from kernfs_fop_write_iter+0x154/0x1a0
kernfs_fop_write_iter from vfs_write+0x12c/0x184
vfs_write from ksys_write+0x78/0xc0
ksys_write from ret_fast_syscall+0x0/0x54
Exception stack(0xcc93dfa8 to 0xcc93dff0)
[...]
PM: noirq suspend of devices complete after 3095.584 msecs
Link: https://github.com/raspberrypi/firmware/issues/1894
Fixes: 0bae6af6d7 ("mailbox: Enable BCM2835 mailbox support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e92d87c9c5 ]
MODULE_DEVICE_TABLE(of, rockchip_mbox_of_match) could let the module
properly autoloaded based on the alias from of_device_id table. It
should be 'rockchip_mbox_of_match' instead of 'rockchp_mbox_of_match',
just fix it.
Fixes: f70ed3b5dc ("mailbox: rockchip: Add Rockchip mailbox driver")
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe513c2ef0 ]
static_call_module_notify() triggers a WARN_ON(), when memory allocation
fails in __static_call_add_module().
That's not really justified, because the failure case must be correctly
handled by the well known call chain and the error code is passed
through to the initiating userspace application.
A memory allocation fail is not a fatal problem, but the WARN_ON() takes
the machine out when panic_on_warn is set.
Replace it with a pr_warn().
Fixes: 9183c3f9ed ("static_call: Add inline static call infrastructure")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/8734mf7pmb.ffs@tglx
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b30051c48 ]
Module insertion invokes static_call_add_module() to initialize the static
calls in a module. static_call_add_module() invokes __static_call_init(),
which allocates a struct static_call_mod to either encapsulate the built-in
static call sites of the associated key into it so further modules can be
added or to append the module to the module chain.
If that allocation fails the function returns with an error code and the
module core invokes static_call_del_module() to clean up eventually added
static_call_mod entries.
This works correctly, when all keys used by the module were converted over
to a module chain before the failure. If not then static_call_del_module()
causes a #GP as it blindly assumes that key::mods points to a valid struct
static_call_mod.
The problem is that key::mods is not a individual struct member of struct
static_call_key, it's part of a union to save space:
union {
/* bit 0: 0 = mods, 1 = sites */
unsigned long type;
struct static_call_mod *mods;
struct static_call_site *sites;
};
key::sites is a pointer to the list of built-in usage sites of the static
call. The type of the pointer is differentiated by bit 0. A mods pointer
has the bit clear, the sites pointer has the bit set.
As static_call_del_module() blidly assumes that the pointer is a valid
static_call_mod type, it fails to check for this failure case and
dereferences the pointer to the list of built-in call sites, which is
obviously bogus.
Cure it by checking whether the key has a sites or a mods pointer.
If it's a sites pointer then the key is not to be touched. As the sites are
walked in the same order as in __static_call_init() the site walk can be
terminated because all subsequent sites have not been touched by the init
code due to the error exit.
If it was converted before the allocation fail, then the inner loop which
searches for a module match will find nothing.
A fail in the second allocation in __static_call_init() is harmless and
does not require special treatment. The first allocation succeeded and
converted the key to a module chain. That first entry has mod::mod == NULL
and mod::next == NULL, so the inner loop of static_call_del_module() will
neither find a module match nor a module chain. The next site in the walk
was either already converted, but can't match the module, or it will exit
the outer loop because it has a static_call_site pointer and not a
static_call_mod pointer.
Fixes: 9183c3f9ed ("static_call: Add inline static call infrastructure")
Closes: https://lore.kernel.org/all/20230915082126.4187913-1-ruanjinjie@huawei.com
Reported-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/87zfon6b0s.ffs@tglx
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0df874c671 upstream.
dev_err_probe() already prints the error code in a human readable way, so
there is no need to duplicate it as a numerical value at the end of the
message.
Fixes: 12f62a857c ("spi: lpspi: Silence error message upon deferred probe")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-By: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/253543c462b765eca40ba54c66f4e3fdf4acdeb7.1659735546.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1db4da5507 upstream.
In accordance with the existing comment and code analysis
it is quite likely that there is a missed 'else' when adapter
times out. Add it.
Fixes: 5bc1200852 ("i2c: Add Intel SCH SMBus support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: <stable@vger.kernel.org> # v2.6.27+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93701d3b84 upstream.
When the i2c bus recovery occurs, driver will send i2c stop command
in the scl low condition. In this case the sw state will still keep
original situation. Under multi-master usage, i2c bus recovery will
be called when i2c transfer timeout occurs. Update the stop command
calling with aspeed_i2c_do_stop function to update master_state.
Fixes: f327c686d3 ("i2c: aspeed: added driver for Aspeed I2C")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Tommy Huang <tommy_huang@aspeedtech.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69b50d4351 upstream.
The generic mmap_base code tries to leave a gap between the top of the
stack and the mmap base address, but enforces a minimum gap size (MIN_GAP)
of 128MB, which is too large on some setups. In particular, on arm tasks
without ADDR_LIMIT_32BIT, the STACK_TOP value is less than 128MB, so it's
impossible to fit such a gap in.
Only enforce this minimum if MIN_GAP < MAX_GAP, as we'd prefer to honour
MAX_GAP, which is defined proportionally, so scales better and always
leaves us with both _some_ stack space and some room for mmap.
This fixes the usercopy KUnit test suite on 32-bit arm, as it doesn't set
any personality flags so gets the default (in this case 26-bit) task size.
This test can be run with: ./tools/testing/kunit/kunit.py run --arch arm
usercopy --make_options LLVM=1
Link: https://lkml.kernel.org/r/20240803074642.1849623-2-davidgow@google.com
Fixes: dba79c3df4 ("arm: use generic mmap top-down layout and brk randomization")
Signed-off-by: David Gow <davidgow@google.com>
Reviewed-by: Kees Cook <kees@kernel.org>
Cc: Alexandre Ghiti <alex@ghiti.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 300a90b2cb upstream.
bpf task local storage is now using task_struct->bpf_storage, so
bpf_lsm_blob_sizes.lbs_task is no longer needed. Remove it to save some
memory.
Fixes: a10787e6d5 ("bpf: Enable task local storage for tracing programs")
Cc: stable@vger.kernel.org
Cc: KP Singh <kpsingh@kernel.org>
Cc: Matt Bobrowski <mattbobrowski@google.com>
Signed-off-by: Song Liu <song@kernel.org>
Acked-by: Matt Bobrowski <mattbobrowski@google.com>
Link: https://lore.kernel.org/r/20240911055508.9588-1-song@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 477d81a1c4 ]
common_interrupt() and related variants call kvm_set_cpu_l1tf_flush_l1d(),
which is neither marked noinstr nor __always_inline.
So compiler puts it out of line and adds instrumentation to it. Since the
call is inside of instrumentation_begin/end(), objtool does not warn about
it.
The manifestation is that KCOV produces spurious coverage in
kvm_set_cpu_l1tf_flush_l1d() in random places because the call happens when
preempt count is not yet updated to say that the kernel is in an interrupt.
Mark kvm_set_cpu_l1tf_flush_l1d() as __always_inline and move it out of the
instrumentation_begin/end() section. It only calls __this_cpu_write()
which is already safe to call in noinstr contexts.
Fixes: 6368558c37 ("x86/entry: Provide IDTENTRY_SYSVEC")
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexander Potapenko <glider@google.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/3f9a1de9e415fcb53d07dc9e19fa8481bb021b1b.1718092070.git.dvyukov@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90f3572082 ]
FRED and IDT can share most of the definitions and declarations so
that in the majority of cases the actual handler implementation is the
same.
The differences are the exceptions where FRED stores exception related
information on the stack and the sysvec implementations as FRED can
handle irqentry/exit() in the dispatcher instead of having it in each
handler.
Also add stub defines for vectors which are not used due to Kconfig
decisions to spare the ifdeffery in the actual FRED dispatch code.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Xin Li <xin3.li@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Shan Kang <shan.kang@intel.com>
Link: https://lore.kernel.org/r/20231205105030.8698-23-xin3.li@intel.com
Stable-dep-of: 477d81a1c4 ("x86/entry: Remove unwanted instrumentation in common_interrupt()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62c5a01a57 ]
In parport_attach, the return value of ida_alloc is unchecked, witch leads
to the use of an invalid index value.
To address this issue, index should be checked. When the index value is
abnormal, the device should be freed.
Found by code review, compile tested only.
Cc: stable@vger.kernel.org
Fixes: fb56d97df7 ("pps: client: use new parport device model")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Link: https://lore.kernel.org/r/20240828131814.3034338-1-make24@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55dbc5b517 ]
ida_alloc() and ida_free() should be preferred to the deprecated
ida_simple_get() and ida_simple_remove().
This is less verbose.
Link: https://lkml.kernel.org/r/9f681747d446b874952a892491387d79ffe565a9.1713089394.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Rodolfo Giometti <giometti@enneenne.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Stable-dep-of: 62c5a01a57 ("pps: add an error check in parport_attach")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5fa8db0be ]
Streams should flush their TRB cache, re-read TRBs, and start executing
TRBs from the beginning of the new dequeue pointer after a 'Set TR Dequeue
Pointer' command.
Cadence controllers may fail to start from the beginning of the dequeue
TRB as it doesn't clear the Opaque 'RsvdO' field of the stream context
during 'Set TR Dequeue' command. This stream context area is where xHC
stores information about the last partially executed TD when a stream
is stopped. xHC uses this information to resume the transfer where it left
mid TD, when the stream is restarted.
Patch fixes this by clearing out all RsvdO fields before initializing new
Stream transfer using a 'Set TR Dequeue Pointer' command.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: stable@vger.kernel.org
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB95386A40146E3EC64086F409DD9D2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc162403e3 ]
This quirk is for the controller that has a limitation in supporting
separate ERSTBA_HI and ERSTBA_LO programming. It's supported when
the ERSTBA is programmed ERSTBA_HI before ERSTBA_LO. That's because
the internal initialization of event ring fetches the
"Event Ring Segment Table Entry" based on the indication of ERSTBA_LO
written.
Signed-off-by: Daehwan Jung <dh10.jung@samsung.com>
Link: https://lore.kernel.org/r/1718019553-111939-3-git-send-email-dh10.jung@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: e5fa8db0be ("usb: xhci: fix loss of data on Cadence xHC")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf97c5e0f7 ]
xhci_add_interrupter() erroneously preserves only the lowest 4 bits when
writing the ERSTBA register, not the lowest 6 bits. Fix it.
Migrate the ERST_BASE_RSVDP macro to the modern GENMASK_ULL() syntax to
avoid a u64 cast.
This was previously fixed by commit 8c1cbec9db ("xhci: fix event ring
segment table related masks and variables in header"), but immediately
undone by commit b17a57f89f ("xhci: Refactor interrupter code for
initial multi interrupter support.").
Fixes: b17a57f89f ("xhci: Refactor interrupter code for initial multi interrupter support.")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v6.3+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230915143108.1532163-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: e5fa8db0be ("usb: xhci: fix loss of data on Cadence xHC")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b17a57f89f ]
xHC supports several interrupters, each with its own mmio register set,
event ring and MSI/MSI-X vector. Transfers can be assigned different
interrupters when queued. See xhci 4.17 for details.
Current driver only supports one interrupter.
Create a xhci_interrupter structure containing an event ring, pointer to
mmio registers for this interrupter, variables to store registers over s3
suspend, erst, etc. Add functions to create and free an interrupter, and
pass an interrupter pointer to functions that deal with events.
Secondary interrupters are also useful without having an interrupt vector.
One use case is the xHCI audio sideband offloading where a DSP can take
care of specific audio endpoints.
When all transfer events of an offloaded endpoint can be mapped to a
separate interrupter event ring the DSP can poll this ring, and we can mask
these events preventing waking up the CPU.
Only minor functional changes such as clearing some of the interrupter
registers when freeing the interrupter.
Still create only one primary interrupter.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230202150505.618915-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: e5fa8db0be ("usb: xhci: fix loss of data on Cadence xHC")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54f9927dfe ]
Time to remove this test trb in td math check that was added
in early stage of xhci driver development.
It verified that the size, alignment and boundaries of the event and
command rings allocated by the driver itself are correct.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230202150505.618915-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: e5fa8db0be ("usb: xhci: fix loss of data on Cadence xHC")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c1cbec9db ]
xHC controller can supports up to 1024 interrupters.
To fit these change the max_interrupters varable from u8 to u16.
Add a separate mask for the reserve and preserve bits [5:0] in the erst
base register and use it instead of the ERST_PRT_MASK.
ERSR_PTR_MASK [3:0] is intended for masking bits in the
event ring dequeue pointer register.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230202150505.618915-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: e5fa8db0be ("usb: xhci: fix loss of data on Cadence xHC")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93907620b3 ]
The write code path touches the bbu member in a non atomic manner
without taking the spinlock. Fix it.
The bug is as old as the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240912132126.1034743-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86b20af11e ]
There is a general misunderstanding amongst engineers that {v}snprintf()
returns the length of the data *actually* encoded into the destination
array. However, as per the C99 standard {v}snprintf() really returns
the length of the data that *would have been* written if there were
enough space for it. This misunderstanding has led to buffer-overruns
in the past. It's generally considered safer to use the {v}scnprintf()
variants in their place (or even sprintf() in simple cases). So let's
do that.
Whilst we're at it, let's define some magic numbers to increase
readability and ease of maintenance.
Link: https://lwn.net/Articles/69419/
Link: https://github.com/KSPP/linux/issues/105
Cc: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20231213164246.1021885-9-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 93907620b3 ("USB: misc: yurex: fix race between read and write")
Signed-off-by: Sasha Levin <sashal@kernel.org>
