[ Upstream commit 0c1d1591f8 ]
If the OS does not support recovering the state left by the
bootloader it needs a way to reset display hardware, so that it can
start from a clean state. Add a reference to the relevant reset.
It fixes display init issue appeared in Linux v6.17: without reset
device boots into black screen and you need to turn display off/on
to "fix" it. Also sometimes it can boot into solid blue color
with these messages in kernel log:
hw recovery is not complete for ctl:2
[drm:dpu_encoder_phys_vid_prepare_for_kickoff:569] [dpu error]enc33
intf1 ctl 2 reset failure: -22
[drm:dpu_encoder_frame_done_timeout:2727] [dpu error]enc33 frame
done timeout
Fixes: 0e789b491b ("pmdomain: core: Leave powered-on genpds on until sync_state")
Cc: stable@vger.kernel.org # 6.17
Signed-off-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251116-sdm660-mdss-reset-v2-3-6219bec0a97f@postmarketos.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d51b70926 ]
On X Elite, the DP PHY needs another clock called ref, while all other
platforms do not.
The current X Elite devices supported upstream work fine without this
clock, because the boot firmware leaves this clock enabled. But we should
not rely on that. Also, even though this change breaks the ABI, it is
needed in order to make the driver disables this clock along with the
other ones, for a proper bring-down of the entire PHY.
So in order to handle these clocks on different platforms, make the driver
get all the clocks regardless of how many there are provided.
Cc: stable@vger.kernel.org # v6.10
Fixes: db83c107dc ("phy: qcom: edp: Add v6 specific ops and X1E80100 platform support")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://patch.msgid.link/20251224-phy-qcom-edp-add-missing-refclk-v5-2-3f45d349b5ac@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11721c45a8 ]
__pci_read_base() sets resource start and end addresses when resource
is larger than 4G but pci_bus_addr_t or resource_size_t are not capable
of representing 64-bit PCI addresses. This creates a problematic
resource that has non-zero flags but the start and end addresses do not
yield to resource size of 0 but 1.
Replace custom resource addresses setup with resource_set_range()
that correctly sets end address as -1 which results in resource_size()
returning 0.
For consistency, also use resource_set_range() in the other branch that
does size based resource setup.
Fixes: 23b13bc76f ("PCI: Fail safely if we can't handle BARs larger than 4GB")
Link: https://lore.kernel.org/all/20251207215359.28895-1-ansuelsmth@gmail.com/T/#m990492684913c5a158ff0e5fc90697d8ad95351b
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Cc: stable@vger.kernel.org
Cc: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20251208145654.5294-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 142d5869f6 ]
This reverts commit 8d3bf19f1b.
While this fake hotplugging was a nice idea, it has shown that this feature
does not handle PCIe switches correctly:
pci_bus 0004:43: busn_res: can not insert [bus 43-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:43: busn_res: [bus 43-41] end is updated to 43
pci_bus 0004:43: busn_res: can not insert [bus 43] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:00.0: devices behind bridge are unusable because [bus 43] cannot be assigned for them
pci_bus 0004:44: busn_res: can not insert [bus 44-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:44: busn_res: [bus 44-41] end is updated to 44
pci_bus 0004:44: busn_res: can not insert [bus 44] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:02.0: devices behind bridge are unusable because [bus 44] cannot be assigned for them
pci_bus 0004:45: busn_res: can not insert [bus 45-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:45: busn_res: [bus 45-41] end is updated to 45
pci_bus 0004:45: busn_res: can not insert [bus 45] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:06.0: devices behind bridge are unusable because [bus 45] cannot be assigned for them
pci_bus 0004:46: busn_res: can not insert [bus 46-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:46: busn_res: [bus 46-41] end is updated to 46
pci_bus 0004:46: busn_res: can not insert [bus 46] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:0e.0: devices behind bridge are unusable because [bus 46] cannot be assigned for them
pci_bus 0004:42: busn_res: [bus 42-41] end is updated to 46
pci_bus 0004:42: busn_res: can not insert [bus 42-46] under [bus 41] (conflicts with (null) [bus 41])
pci 0004:41:00.0: devices behind bridge are unusable because [bus 42-46] cannot be assigned for them
pcieport 0004:40:00.0: bridge has subordinate 41 but max busn 46
During the initial scan, PCI core doesn't see the switch and since the Root
Port is not hot plug capable, the secondary bus number gets assigned as the
subordinate bus number. This means, the PCI core assumes that only one bus
will appear behind the Root Port since the Root Port is not hot plug
capable.
This works perfectly fine for PCIe endpoints connected to the Root Port,
since they don't extend the bus. However, if a PCIe switch is connected,
then there is a problem when the downstream busses starts showing up and
the PCI core doesn't extend the subordinate bus number and bridge resources
after initial scan during boot.
So revert the change that skipped dw_pcie_wait_for_link() if the Link up
IRQ was used by a vendor glue driver.
Suggested-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251222064207.3246632-14-cassel@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a9793b558 ]
This reverts commit 4581403f67.
While this fake hotplugging was a nice idea, it has shown that this feature
does not handle PCIe switches correctly:
pci_bus 0004:43: busn_res: can not insert [bus 43-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:43: busn_res: [bus 43-41] end is updated to 43
pci_bus 0004:43: busn_res: can not insert [bus 43] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:00.0: devices behind bridge are unusable because [bus 43] cannot be assigned for them
pci_bus 0004:44: busn_res: can not insert [bus 44-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:44: busn_res: [bus 44-41] end is updated to 44
pci_bus 0004:44: busn_res: can not insert [bus 44] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:02.0: devices behind bridge are unusable because [bus 44] cannot be assigned for them
pci_bus 0004:45: busn_res: can not insert [bus 45-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:45: busn_res: [bus 45-41] end is updated to 45
pci_bus 0004:45: busn_res: can not insert [bus 45] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:06.0: devices behind bridge are unusable because [bus 45] cannot be assigned for them
pci_bus 0004:46: busn_res: can not insert [bus 46-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:46: busn_res: [bus 46-41] end is updated to 46
pci_bus 0004:46: busn_res: can not insert [bus 46] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:0e.0: devices behind bridge are unusable because [bus 46] cannot be assigned for them
pci_bus 0004:42: busn_res: [bus 42-41] end is updated to 46
pci_bus 0004:42: busn_res: can not insert [bus 42-46] under [bus 41] (conflicts with (null) [bus 41])
pci 0004:41:00.0: devices behind bridge are unusable because [bus 42-46] cannot be assigned for them
pcieport 0004:40:00.0: bridge has subordinate 41 but max busn 46
During the initial scan, PCI core doesn't see the switch and since the Root
Port is not hot plug capable, the secondary bus number gets assigned as the
subordinate bus number. This means, the PCI core assumes that only one bus
will appear behind the Root Port since the Root Port is not hot plug
capable.
This works perfectly fine for PCIe endpoints connected to the Root Port,
since they don't extend the bus. However, if a PCIe switch is connected,
then there is a problem when the downstream busses starts showing up and
the PCI core doesn't extend the subordinate bus number and bridge resources
after initial scan during boot.
The long term plan is to migrate this driver to the upcoming pwrctrl APIs
that are supposed to handle this problem elegantly.
Suggested-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251222064207.3246632-13-cassel@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ebdefb879 ]
This reverts commit ba4a2e2317.
Since the Link up IRQ support is going away, revert the MSI logic that got
added for it too.
Suggested-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[mani: reworded the description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251222064207.3246632-12-cassel@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9ce5b3804 ]
This reverts commit 36971d6c5a.
While this fake hotplugging was a nice idea, it has shown that this feature
does not handle PCIe switches correctly:
pci_bus 0004:43: busn_res: can not insert [bus 43-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:43: busn_res: [bus 43-41] end is updated to 43
pci_bus 0004:43: busn_res: can not insert [bus 43] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:00.0: devices behind bridge are unusable because [bus 43] cannot be assigned for them
pci_bus 0004:44: busn_res: can not insert [bus 44-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:44: busn_res: [bus 44-41] end is updated to 44
pci_bus 0004:44: busn_res: can not insert [bus 44] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:02.0: devices behind bridge are unusable because [bus 44] cannot be assigned for them
pci_bus 0004:45: busn_res: can not insert [bus 45-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:45: busn_res: [bus 45-41] end is updated to 45
pci_bus 0004:45: busn_res: can not insert [bus 45] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:06.0: devices behind bridge are unusable because [bus 45] cannot be assigned for them
pci_bus 0004:46: busn_res: can not insert [bus 46-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:46: busn_res: [bus 46-41] end is updated to 46
pci_bus 0004:46: busn_res: can not insert [bus 46] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:0e.0: devices behind bridge are unusable because [bus 46] cannot be assigned for them
pci_bus 0004:42: busn_res: [bus 42-41] end is updated to 46
pci_bus 0004:42: busn_res: can not insert [bus 42-46] under [bus 41] (conflicts with (null) [bus 41])
pci 0004:41:00.0: devices behind bridge are unusable because [bus 42-46] cannot be assigned for them
pcieport 0004:40:00.0: bridge has subordinate 41 but max busn 46
During the initial scan, PCI core doesn't see the switch and since the Root
Port is not hot plug capable, the secondary bus number gets assigned as the
subordinate bus number. This means, the PCI core assumes that only one bus
will appear behind the Root Port since the Root Port is not hot plug
capable.
This works perfectly fine for PCIe endpoints connected to the Root Port,
since they don't extend the bus. However, if a PCIe switch is connected,
then there is a problem when the downstream busses starts showing up and
the PCI core doesn't extend the subordinate bus number and bridge resources
after initial scan during boot.
The long term plan is to migrate this driver to the upcoming pwrctrl APIs
that are supposed to handle this problem elegantly.
Suggested-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251222064207.3246632-11-cassel@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc6298086b ]
This reverts commit ec9fd499b9.
While this fake hotplugging was a nice idea, it has shown that this feature
does not handle PCIe switches correctly:
pci_bus 0004:43: busn_res: can not insert [bus 43-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:43: busn_res: [bus 43-41] end is updated to 43
pci_bus 0004:43: busn_res: can not insert [bus 43] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:00.0: devices behind bridge are unusable because [bus 43] cannot be assigned for them
pci_bus 0004:44: busn_res: can not insert [bus 44-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:44: busn_res: [bus 44-41] end is updated to 44
pci_bus 0004:44: busn_res: can not insert [bus 44] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:02.0: devices behind bridge are unusable because [bus 44] cannot be assigned for them
pci_bus 0004:45: busn_res: can not insert [bus 45-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:45: busn_res: [bus 45-41] end is updated to 45
pci_bus 0004:45: busn_res: can not insert [bus 45] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:06.0: devices behind bridge are unusable because [bus 45] cannot be assigned for them
pci_bus 0004:46: busn_res: can not insert [bus 46-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:46: busn_res: [bus 46-41] end is updated to 46
pci_bus 0004:46: busn_res: can not insert [bus 46] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:0e.0: devices behind bridge are unusable because [bus 46] cannot be assigned for them
pci_bus 0004:42: busn_res: [bus 42-41] end is updated to 46
pci_bus 0004:42: busn_res: can not insert [bus 42-46] under [bus 41] (conflicts with (null) [bus 41])
pci 0004:41:00.0: devices behind bridge are unusable because [bus 42-46] cannot be assigned for them
pcieport 0004:40:00.0: bridge has subordinate 41 but max busn 46
During the initial scan, PCI core doesn't see the switch and since the Root
Port is not hot plug capable, the secondary bus number gets assigned as the
subordinate bus number. This means, the PCI core assumes that only one bus
will appear behind the Root Port since the Root Port is not hot plug
capable.
This works perfectly fine for PCIe endpoints connected to the Root Port,
since they don't extend the bus. However, if a PCIe switch is connected,
then there is a problem when the downstream busses starts showing up and
the PCI core doesn't extend the subordinate bus number and bridge resources
after initial scan during boot.
The long term plan is to migrate this driver to the upcoming pwrctrl APIs
that are supposed to handle this problem elegantly.
Suggested-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251222064207.3246632-9-cassel@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f41307d58 ]
Acquire and release the GEM object's reservation lock around calls
to the object's purge operation. The tests use
drm_gem_shmem_purge_locked(), which led to errors such as show below.
[ 58.709128] WARNING: CPU: 1 PID: 1354 at drivers/gpu/drm/drm_gem_shmem_helper.c:515 drm_gem_shmem_purge_locked+0x51c/0x740
Only export the new helper drm_gem_shmem_purge() for Kunit tests.
This is not an interface for regular drivers.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 954907f714 ("drm/shmem-helper: Refactor locked/unlocked functions")
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v6.16+
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patch.msgid.link/20251212160317.287409-6-tzimmermann@suse.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 607d07d8cc ]
Acquire and release the GEM object's reservation lock around calls
to the object's madvide operation. The tests use
drm_gem_shmem_madvise_locked(), which led to errors such as show below.
[ 58.339389] WARNING: CPU: 1 PID: 1352 at drivers/gpu/drm/drm_gem_shmem_helper.c:499 drm_gem_shmem_madvise_locked+0xde/0x140
Only export the new helper drm_gem_shmem_madvise() for Kunit tests.
This is not an interface for regular drivers.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 954907f714 ("drm/shmem-helper: Refactor locked/unlocked functions")
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v6.16+
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patch.msgid.link/20251212160317.287409-5-tzimmermann@suse.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cda83b099f ]
Acquire and release the GEM object's reservation lock around vmap and
vunmap operations. The tests use vmap_locked, which led to errors such
as show below.
[ 122.292030] WARNING: CPU: 3 PID: 1413 at drivers/gpu/drm/drm_gem_shmem_helper.c:390 drm_gem_shmem_vmap_locked+0x3a3/0x6f0
[ 122.468066] WARNING: CPU: 3 PID: 1413 at drivers/gpu/drm/drm_gem_shmem_helper.c:293 drm_gem_shmem_pin_locked+0x1fe/0x350
[ 122.563504] WARNING: CPU: 3 PID: 1413 at drivers/gpu/drm/drm_gem_shmem_helper.c:234 drm_gem_shmem_get_pages_locked+0x23c/0x370
[ 122.662248] WARNING: CPU: 2 PID: 1413 at drivers/gpu/drm/drm_gem_shmem_helper.c:452 drm_gem_shmem_vunmap_locked+0x101/0x330
Only export the new vmap/vunmap helpers for Kunit tests. These are
not interfaces for regular drivers.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 954907f714 ("drm/shmem-helper: Refactor locked/unlocked functions")
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v6.16+
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patch.msgid.link/20251212160317.287409-4-tzimmermann@suse.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b47b9ecef3 ]
Automatically unpin pages on cleanup. The test currently fails with
the error
[ 58.246263] drm-kunit-mock-device drm_gem_shmem_test_get_sg_table.drm-kunit-mock-device: [drm] drm_WARN_ON(refcount_read(&shmem->pages_pin_count))
while cleaning up the GEM object. The pin count has to be zero at this
point.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: d586b535f1 ("drm/shmem-helper: Add and use pages_pin_count")
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v6.16+
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patch.msgid.link/20251212160317.287409-3-tzimmermann@suse.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89f23d4200 ]
GEM SHMEM has 2 helpers for exporting S/G tables. Swap the names of
the rsp. tests, so that each matches the helper it tests.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 93032ae634 ("drm/test: add a test suite for GEM objects backed by shmem")
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v6.8+
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patch.msgid.link/20251212160317.287409-2-tzimmermann@suse.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 267f53140c ]
The dfl code adds a bus. If it is built-in and there is a built-in driver
as well, the dfl module_init may be called after the driver module_init,
leading to a failure to register the driver as the bus has not been added
yet.
Use subsys_initcall, which guarantees it will be called before the drivers
init code.
Without the fix, we see failures like this:
[ 0.479475] Driver 'intel-m10-bmc' was unable to register with bus_type 'dfl' because the bus was not initialized.
Cc: stable@vger.kernel.org
Fixes: 9ba3a0aa09 ("fpga: dfl: create a dfl bus type to support DFL devices")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com>
Link: https://lore.kernel.org/r/20251215-dfl_subsys-v1-1-21807bad6b10@igalia.com
Reviewed-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Xu Yilun <yilun.xu@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebcfdbe4ad ]
When the bytes data is read from the firmware, the size of the payload
can be different than what it was previously.
For example when the topology did not contained payload data at all for the
control, the data size was 0.
For get operation allow maximum size of payload to be read and then update
the sizes according to the completed message.
Similarly, keep the size in sync when updating the data in firmware.
With the change we will be able to read data from firmware for bytes
controls which did not had initial payload defined in topology.
Fixes: a062c8899f ("ASoC: SOF: ipc4-control: Add support for bytes control get and put")
Cc: stable@vger.kernel.org
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://patch.msgid.link/20251217143945.2667-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1876fc33c ]
The size of the data behind scontrol->ipc_control_data is stored in
scontrol->size, use this when copying data for backup/restore.
Fixes: db38d86d0c ("ASoC: sof: Improve sof_ipc4_bytes_ext_put function")
Cc: stable@vger.kernel.org
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://patch.msgid.link/20251217143945.2667-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a653820700 ]
The size of the data behind of scontrol->ipc_control_data for bytes
controls is:
[1] sizeof(struct sof_ipc4_control_data) + // kernel only struct
[2] sizeof(struct sof_abi_hdr)) + payload
The max_size specifies the size of [2] and it is coming from topology.
Change the function to take this into account and allocate adequate amount
of memory behind scontrol->ipc_control_data.
With the change we will allocate [1] amount more memory to be able to hold
the full size of data.
Fixes: a382082ff7 ("ASoC: SOF: ipc4-topology: Add support for TPLG_CTL_BYTES")
Cc: stable@vger.kernel.org
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://patch.msgid.link/20251217143945.2667-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fa7471374 ]
When the bytes control have no data (payload) then there is no need to send
an IPC message as there is nothing to send.
Fixes: a062c8899f ("ASoC: SOF: ipc4-control: Add support for bytes control get and put")
Cc: stable@vger.kernel.org
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://patch.msgid.link/20251217143945.2667-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efe2489848 ]
Commit 506aa8b02a ("dma-fence: Add safe access helpers and document
the rules") details the dma-fence safe access rules. The most common
culprit is that drm_sched_fence_get_timeline_name may race with
group_free_queue.
Signed-off-by: Chia-I Wu <olvaffe@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Cc: stable@vger.kernel.org # v6.17+
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patch.msgid.link/20251204174545.399059-1-olvaffe@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de86dbc0fb ]
The power switch used to power the SD card interface might have
more than 2ms turn-on time, increase the startup delay to 20ms to
prevent failures.
Fixes: 87f95ea316 ("arm64: dts: ti: Add Toradex Verdin AM62P")
Cc: stable@vger.kernel.org
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://patch.msgid.link/20251209084126.33282-1-francesco@dolcini.it
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 126fb0ce99 ]
When hfsplus was converted to the new mount api a bug was introduced by
changing the allocation pattern of sb->s_fs_info. If setup_bdev_super()
fails after a new superblock has been allocated by sget_fc(), but before
hfsplus_fill_super() takes ownership of the filesystem-specific s_fs_info
data it was leaked.
Fix this by freeing sb->s_fs_info in hfsplus_kill_super().
Cc: stable@vger.kernel.org
Fixes: 432f7c78cb ("hfsplus: convert hfsplus to use the new mount api")
Reported-by: Viacheslav Dubeyko <Slava.Dubeyko@ibm.com>
Tested-by: Viacheslav Dubeyko <Slava.Dubeyko@ibm.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Mehdi Ben Hadj Khelifa <mehdi.benhadjkhelifa@gmail.com>
Reviewed-by: Viacheslav Dubeyko <slava@dubeyko.com>
Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
Link: https://lore.kernel.org/r/20251201222843.82310-3-mehdi.benhadjkhelifa@gmail.com
Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42023d4b6d ]
The driver_override_show function reads the driver_override string
without holding the device_lock. However, the store function modifies
and frees the string while holding the device_lock. This creates a race
condition where the string can be freed by the store function while
being read by the show function, leading to a use-after-free.
To fix this, replace the rpmsg_string_attr macro with explicit show and
store functions. The new driver_override_store uses the standard
driver_set_override helper. Since the introduction of
driver_set_override, the comments in include/linux/rpmsg.h have stated
that this helper must be used to set or clear driver_override, but the
implementation was not updated until now.
Because driver_set_override modifies and frees the string while holding
the device_lock, the new driver_override_show now correctly holds the
device_lock during the read operation to prevent the race.
Additionally, since rpmsg_string_attr has only ever been used for
driver_override, removing the macro simplifies the code.
Fixes: 39e47767ec ("rpmsg: Add driver_override device attribute for rpmsg_device")
Cc: stable@vger.kernel.org
Signed-off-by: Gui-Dong Han <hanguidong02@gmail.com>
Link: https://lore.kernel.org/r/20251202174948.12693-1-hanguidong02@gmail.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit baed0d9ba9 ]
In decode_choice(), the boundary check before get_len() uses the
variable `len`, which is still 0 from its initialization at the top of
the function:
unsigned int type, ext, len = 0;
...
if (ext || (son->attr & OPEN)) {
BYTE_ALIGN(bs);
if (nf_h323_error_boundary(bs, len, 0)) /* len is 0 here */
return H323_ERROR_BOUND;
len = get_len(bs); /* OOB read */
When the bitstream is exactly consumed (bs->cur == bs->end), the check
nf_h323_error_boundary(bs, 0, 0) evaluates to (bs->cur + 0 > bs->end),
which is false. The subsequent get_len() call then dereferences
*bs->cur++, reading 1 byte past the end of the buffer. If that byte
has bit 7 set, get_len() reads a second byte as well.
This can be triggered remotely by sending a crafted Q.931 SETUP message
with a User-User Information Element containing exactly 2 bytes of
PER-encoded data ({0x08, 0x00}) to port 1720 through a firewall with
the nf_conntrack_h323 helper active. The decoder fully consumes the
PER buffer before reaching this code path, resulting in a 1-2 byte
heap-buffer-overflow read confirmed by AddressSanitizer.
Fix this by checking for 2 bytes (the maximum that get_len() may read)
instead of the uninitialized `len`. This matches the pattern used at
every other get_len() call site in the same file, where the caller
checks for 2 bytes of available data before calling get_len().
Fixes: ec8a8f3c31 ("netfilter: nf_ct_h323: Extend nf_h323_error_boundary to work on bits as well")
Signed-off-by: Vahagn Vardanian <vahagn@redrays.io>
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://patch.msgid.link/20260225130619.1248-2-fw@strlen.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a5752c6dc ]
The driver obtains sw_attr.num_ifs from firmware via dpsw_get_attributes()
but never validates it against DPSW_MAX_IF (64). This value controls
iteration in dpaa2_switch_fdb_get_flood_cfg(), which writes port indices
into the fixed-size cfg->if_id[DPSW_MAX_IF] array. When firmware reports
num_ifs >= 64, the loop can write past the array bounds.
Add a bound check for num_ifs in dpaa2_switch_init().
dpaa2_switch_fdb_get_flood_cfg() appends the control interface (port
num_ifs) after all matched ports. When num_ifs == DPSW_MAX_IF and all
ports match the flood filter, the loop fills all 64 slots and the control
interface write overflows by one entry.
The check uses >= because num_ifs == DPSW_MAX_IF is also functionally
broken.
build_if_id_bitmap() silently drops any ID >= 64:
if (id[i] < DPSW_MAX_IF)
bmap[id[i] / 64] |= ...
Fixes: 539dda3c5d ("staging: dpaa2-switch: properly setup switching domains")
Signed-off-by: Junrui Luo <moonafterrain@outlook.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://patch.msgid.link/SYBPR01MB78812B47B7F0470B617C408AAF74A@SYBPR01MB7881.ausprd01.prod.outlook.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7aa767d0d3 ]
udpgro_frglist.sh and udpgro_bench.sh are the flakiest tests
currently in NIPA. They fail in the same exact way, TCP GRO
test stalls occasionally and the test gets killed after 10min.
These tests use veth to simulate GRO. They attach a trivial
("return XDP_PASS;") XDP program to the veth to force TSO off
and NAPI on.
Digging into the failure mode we can see that the connection
is completely stuck after a burst of drops. The sender's snd_nxt
is at sequence number N [1], but the receiver claims to have
received (rcv_nxt) up to N + 3 * MSS [2]. Last piece of the puzzle
is that senders rtx queue is not empty (let's say the block in
the rtx queue is at sequence number N - 4 * MSS [3]).
In this state, sender sends a retransmission from the rtx queue
with a single segment, and sequence numbers N-4*MSS:N-3*MSS [3].
Receiver sees it and responds with an ACK all the way up to
N + 3 * MSS [2]. But sender will reject this ack as TCP_ACK_UNSENT_DATA
because it has no recollection of ever sending data that far out [1].
And we are stuck.
The root cause is the mess of the xmit return codes. veth returns
an error when it can't xmit a frame. We end up with a loss event
like this:
-------------------------------------------------
| GSO super frame 1 | GSO super frame 2 |
|-----------------------------------------------|
| seg | seg | seg | seg | seg | seg | seg | seg |
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
-------------------------------------------------
x ok ok <ok>| ok ok ok <x>
\\
snd_nxt
"x" means packet lost by veth, and "ok" means it went thru.
Since veth has TSO disabled in this test it sees individual segments.
Segment 1 is on the retransmit queue and will be resent.
So why did the sender not advance snd_nxt even tho it clearly did
send up to seg 8? tcp_write_xmit() interprets the return code
from the core to mean that data has not been sent at all. Since
TCP deals with GSO super frames, not individual segment the crux
of the problem is that loss of a single segment can be interpreted
as loss of all. TCP only sees the last return code for the last
segment of the GSO frame (in <> brackets in the diagram above).
Of course for the problem to occur we need a setup or a device
without a Qdisc. Otherwise Qdisc layer disconnects the protocol
layer from the device errors completely.
We have multiple ways to fix this.
1) make veth not return an error when it lost a packet.
While this is what I think we did in the past, the issue keeps
reappearing and it's annoying to debug. The game of whack
a mole is not great.
2) fix the damn return codes
We only talk about NETDEV_TX_OK and NETDEV_TX_BUSY in the
documentation, so maybe we should make the return code from
ndo_start_xmit() a boolean. I like that the most, but perhaps
some ancient, not-really-networking protocol would suffer.
3) make TCP ignore the errors
It is not entirely clear to me what benefit TCP gets from
interpreting the result of ip_queue_xmit()? Specifically once
the connection is established and we're pushing data - packet
loss is just packet loss?
4) this fix
Ignore the rc in the Qdisc-less+GSO case, since it's unreliable.
We already always return OK in the TCQ_F_CAN_BYPASS case.
In the Qdisc-less case let's be a bit more conservative and only
mask the GSO errors. This path is taken by non-IP-"networks"
like CAN, MCTP etc, so we could regress some ancient thing.
This is the simplest, but also maybe the hackiest fix?
Similar fix has been proposed by Eric in the past but never committed
because original reporter was working with an OOT driver and wasn't
providing feedback (see Link).
Link: https://lore.kernel.org/CANn89iJcLepEin7EtBETrZ36bjoD9LrR=k4cfwWh046GB+4f9A@mail.gmail.com
Fixes: 1f59533f9c ("qdisc: validate frames going through the direct_xmit path")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260223235100.108939-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 859380694f ]
Fix a "scheduling while atomic" bug in mlx5e_ipsec_init_macs() by
replacing mlx5_query_mac_address() with ether_addr_copy() to get the
local MAC address directly from netdev->dev_addr.
The issue occurs because mlx5_query_mac_address() queries the hardware
which involves mlx5_cmd_exec() that can sleep, but it is called from
the mlx5e_ipsec_handle_event workqueue which runs in atomic context.
The MAC address is already available in netdev->dev_addr, so no need
to query hardware. This avoids the sleeping call and resolves the bug.
Call trace:
BUG: scheduling while atomic: kworker/u112:2/69344/0x00000200
__schedule+0x7ab/0xa20
schedule+0x1c/0xb0
schedule_timeout+0x6e/0xf0
__wait_for_common+0x91/0x1b0
cmd_exec+0xa85/0xff0 [mlx5_core]
mlx5_cmd_exec+0x1f/0x50 [mlx5_core]
mlx5_query_nic_vport_mac_address+0x7b/0xd0 [mlx5_core]
mlx5_query_mac_address+0x19/0x30 [mlx5_core]
mlx5e_ipsec_init_macs+0xc1/0x720 [mlx5_core]
mlx5e_ipsec_build_accel_xfrm_attrs+0x422/0x670 [mlx5_core]
mlx5e_ipsec_handle_event+0x2b9/0x460 [mlx5_core]
process_one_work+0x178/0x2e0
worker_thread+0x2ea/0x430
Fixes: cee137a634 ("net/mlx5e: Handle ESN update events")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260224114652.1787431-6-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60253042c0 ]
The cited commit miss to add locking in the error path of
mlx5_sriov_enable(). When pci_enable_sriov() fails,
mlx5_device_disable_sriov() is called to clean up. This cleanup function
now expects to be called with the devlink instance lock held.
Add the missing devl_lock(devlink) and devl_unlock(devlink)
Fixes: 84a433a40d ("net/mlx5: Lock mlx5 devlink reload callbacks")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260224114652.1787431-5-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7073e8b97 ]
The cited commit introduced MLX5_PRIV_FLAGS_SWITCH_LEGACY to identify
when a transition to legacy mode is requested via devlink. However, the
logic failed to clear this flag if the mode was subsequently changed
back to MLX5_ESWITCH_OFFLOADS (switchdev). Consequently, if a user
toggled from legacy to switchdev, the flag remained set, leaving the
driver with wrong state indicating
Fix this by explicitly clearing the MLX5_PRIV_FLAGS_SWITCH_LEGACY bit
when the requested mode is MLX5_ESWITCH_OFFLOADS.
Fixes: 2a4f56fbcc ("net/mlx5e: Keep netdev when leave switchdev for devlink set legacy only")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260224114652.1787431-4-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd7b9f83fb ]
mlx5_lag_disable_change() unconditionally called mlx5_disable_lag() when
LAG was active, which is incorrect for MLX5_LAG_MODE_MPESW.
Hnece, call mlx5_disable_mpesw() when running in MPESW mode.
Fixes: a32327a3a0 ("net/mlx5: Lag, Control MultiPort E-Switch single FDB mode")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260224114652.1787431-3-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb4c698633 ]
syzbot is reporting
unregister_netdevice: waiting for netdevsim0 to become free. Usage count = 3
ref_tracker: netdev@ffff88807dcf8618 has 1/2 users at
__netdev_tracker_alloc include/linux/netdevice.h:4400 [inline]
netdev_hold include/linux/netdevice.h:4429 [inline]
inetdev_init+0x201/0x4e0 net/ipv4/devinet.c:286
inetdev_event+0x251/0x1610 net/ipv4/devinet.c:1600
notifier_call_chain+0x19d/0x3a0 kernel/notifier.c:85
call_netdevice_notifiers_mtu net/core/dev.c:2318 [inline]
netif_set_mtu_ext+0x5aa/0x800 net/core/dev.c:9886
netif_set_mtu+0xd7/0x1b0 net/core/dev.c:9907
dev_set_mtu+0x126/0x260 net/core/dev_api.c:248
team_port_del+0xb07/0xcb0 drivers/net/team/team_core.c:1333
team_del_slave drivers/net/team/team_core.c:1936 [inline]
team_device_event+0x207/0x5b0 drivers/net/team/team_core.c:2929
notifier_call_chain+0x19d/0x3a0 kernel/notifier.c:85
call_netdevice_notifiers_extack net/core/dev.c:2281 [inline]
call_netdevice_notifiers net/core/dev.c:2295 [inline]
__dev_change_net_namespace+0xcb7/0x2050 net/core/dev.c:12592
do_setlink+0x2ce/0x4590 net/core/rtnetlink.c:3060
rtnl_changelink net/core/rtnetlink.c:3776 [inline]
__rtnl_newlink net/core/rtnetlink.c:3935 [inline]
rtnl_newlink+0x15a9/0x1be0 net/core/rtnetlink.c:4072
rtnetlink_rcv_msg+0x7d5/0xbe0 net/core/rtnetlink.c:6958
netlink_rcv_skb+0x232/0x4b0 net/netlink/af_netlink.c:2550
netlink_unicast_kernel net/netlink/af_netlink.c:1318 [inline]
netlink_unicast+0x80f/0x9b0 net/netlink/af_netlink.c:1344
netlink_sendmsg+0x813/0xb40 net/netlink/af_netlink.c:1894
problem. Ido Schimmel found steps to reproduce
ip link add name team1 type team
ip link add name dummy1 mtu 1499 master team1 type dummy
ip netns add ns1
ip link set dev dummy1 netns ns1
ip -n ns1 link del dev dummy1
and also found that the same issue was fixed in the bond driver in
commit f51048c3e0 ("bonding: avoid NETDEV_CHANGEMTU event when
unregistering slave").
Let's do similar thing for the team driver, with commit ad7c7b2172 ("net:
hold netdev instance lock during sysfs operations") and commit 303a8487a6
("net: s/__dev_set_mtu/__netif_set_mtu/") also applied.
Reported-by: syzbot+881d65229ca4f9ae8c84@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=881d65229ca4f9ae8c84
Suggested-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Fixes: 3d249d4ca7 ("net: introduce ethernet teaming device")
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20260224125709.317574-2-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 745cd46c2a ]
Use the new helper netdev_compute_master_upper_features() to compute the
team device features. This helper performs both the feature computation
and the netdev_change_features() call.
Note that such change replace the lower layer traversing currently done
using team->port_list with netdev_for_each_lower_dev(). Such change is
safe as `port_list` contains exactly the same elements as
`team->dev->adj_list.lower` and the helper is always invoked under the
RTNL lock.
With this change, the explicit netdev_change_features() in team_add_slave()
can be safely removed, as team_port_add() already takes care of the
notification via netdev_compute_master_upper_features(), and same thing for
team_del_slave()
This also fixes missing computations for MPLS, XFRM, and TSO/GSO partial
features.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20251017034155.61990-4-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: bb4c698633 ("team: avoid NETDEV_CHANGEMTU event when unregistering slave")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28098defc7 ]
Some high level software drivers need to compute features from lower
devices. But each has their own implementations and may lost some
feature compute. Let's use one common function to compute features
for kinds of these devices.
The new helper uses the current bond implementation as the reference
one, as the latter already handles all the relevant aspects: netdev
features, TSO limits and dst retention.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20251017034155.61990-2-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: bb4c698633 ("team: avoid NETDEV_CHANGEMTU event when unregistering slave")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f975a09552 ]
While testing corner cases in the driver, a use-after-free crash
was found on the service rescan PCI path.
When mana_serv_reset() calls mana_gd_suspend(), mana_gd_cleanup()
destroys gc->service_wq. If the subsequent mana_gd_resume() fails
with -ETIMEDOUT or -EPROTO, the code falls through to
mana_serv_rescan() which triggers pci_stop_and_remove_bus_device().
This invokes the PCI .remove callback (mana_gd_remove), which calls
mana_gd_cleanup() a second time, attempting to destroy the already-
freed workqueue. Fix this by NULL-checking gc->service_wq in
mana_gd_cleanup() and setting it to NULL after destruction.
Call stack of issue for reference:
[Sat Feb 21 18:53:48 2026] Call Trace:
[Sat Feb 21 18:53:48 2026] <TASK>
[Sat Feb 21 18:53:48 2026] mana_gd_cleanup+0x33/0x70 [mana]
[Sat Feb 21 18:53:48 2026] mana_gd_remove+0x3a/0xc0 [mana]
[Sat Feb 21 18:53:48 2026] pci_device_remove+0x41/0xb0
[Sat Feb 21 18:53:48 2026] device_remove+0x46/0x70
[Sat Feb 21 18:53:48 2026] device_release_driver_internal+0x1e3/0x250
[Sat Feb 21 18:53:48 2026] device_release_driver+0x12/0x20
[Sat Feb 21 18:53:48 2026] pci_stop_bus_device+0x6a/0x90
[Sat Feb 21 18:53:48 2026] pci_stop_and_remove_bus_device+0x13/0x30
[Sat Feb 21 18:53:48 2026] mana_do_service+0x180/0x290 [mana]
[Sat Feb 21 18:53:48 2026] mana_serv_func+0x24/0x50 [mana]
[Sat Feb 21 18:53:48 2026] process_one_work+0x190/0x3d0
[Sat Feb 21 18:53:48 2026] worker_thread+0x16e/0x2e0
[Sat Feb 21 18:53:48 2026] kthread+0xf7/0x130
[Sat Feb 21 18:53:48 2026] ? __pfx_worker_thread+0x10/0x10
[Sat Feb 21 18:53:48 2026] ? __pfx_kthread+0x10/0x10
[Sat Feb 21 18:53:48 2026] ret_from_fork+0x269/0x350
[Sat Feb 21 18:53:48 2026] ? __pfx_kthread+0x10/0x10
[Sat Feb 21 18:53:48 2026] ret_from_fork_asm+0x1a/0x30
[Sat Feb 21 18:53:48 2026] </TASK>
Fixes: 505cc26bca ("net: mana: Add support for auxiliary device servicing events")
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Dipayaan Roy <dipayanroy@linux.microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/aZ2bzL64NagfyHpg@linuxonhyperv3.guj3yctzbm1etfxqx2vob5hsef.xx.internal.cloudapp.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 676c7af91f ]
The devm_add_action_or_reset() function already executes the cleanup
action on failure before returning an error, so the explicit goto error
and subsequent zl3073x_dev_dpll_fini() call causes double cleanup.
Fixes: ebb1031c51 ("dpll: zl3073x: Refactor DPLL initialization")
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Link: https://patch.msgid.link/20260224-dpll-v2-1-d7786414a830@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e3bb184e9 ]
Commit 2bd99aef1b ("tcp: accept bare FIN packets under memory
pressure") allowed accepting FIN packets in tcp_data_queue() even when
the receive window was closed, to prevent ACK/FIN loops with broken
clients.
Such a FIN packet is in sequence, but because the FIN consumes a
sequence number, it extends beyond the window. Before commit
9ca48d616e ("tcp: do not accept packets beyond window"),
tcp_sequence() only required the seq to be within the window. After
that change, the entire packet (including the FIN) must fit within the
window. As a result, such FIN packets are now dropped and the handling
path is no longer reached.
Be more lenient by not counting the sequence number consumed by the
FIN when calling tcp_sequence(), restoring the previous behavior for
cases where only the FIN extends beyond the window.
Fixes: 9ca48d616e ("tcp: do not accept packets beyond window")
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20260224-fix_zero_wnd_fin-v2-1-a16677ea7cea@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 104016eb67 ]
In ib_umem_dmabuf_get_pinned_with_dma_device(), the call to
ib_umem_dmabuf_map_pages() can fail. If this occurs, the dmabuf
is immediately unpinned but the umem_dmabuf->pinned flag is still
set. Then, when ib_umem_release() is called, it calls
ib_umem_dmabuf_revoke() which will call dma_buf_unpin() again.
Fix this by removing the immediate unpin upon failure and just let
the ib_umem_release/revoke path handle it. This also ensures the
proper unmap-unpin unwind ordering if the dmabuf_map_pages call
happened to fail due to dma_resv_wait_timeout (and therefore has
a non-NULL umem_dmabuf->sgt).
Fixes: 1e4df4a21c ("RDMA/umem: Allow pinned dmabuf umem usage")
Signed-off-by: Jacob Moroni <jmoroni@google.com>
Link: https://patch.msgid.link/20260224234153.1207849-1-jmoroni@google.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a2d046e4b ]
Only plain data whose start position and on-disk physical length are
both aligned to the block size should be classified as interlaced
plain extents. Otherwise, it must be treated as shifted plain extents.
This issue was found by syzbot using a crafted compressed image
containing plain extents with unaligned physical lengths, which can
cause OOB read in z_erofs_transform_plain().
Reported-and-tested-by: syzbot+d988dc155e740d76a331@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/r/699d5714.050a0220.cdd3c.03e7.GAE@google.com
Fixes: 1d191b4ca5 ("erofs: implement encoded extent metadata")
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d7e6ce34f ]
pegasus_probe() fills URBs with hardcoded endpoint pipes without
verifying the endpoint descriptors:
- usb_rcvbulkpipe(dev, 1) for RX data
- usb_sndbulkpipe(dev, 2) for TX data
- usb_rcvintpipe(dev, 3) for status interrupts
A malformed USB device can present these endpoints with transfer types
that differ from what the driver assumes.
Add a pegasus_usb_ep enum for endpoint numbers, replacing magic
constants throughout. Add usb_check_bulk_endpoints() and
usb_check_int_endpoints() calls before any resource allocation to
verify endpoint types before use, rejecting devices with mismatched
descriptors at probe time, and avoid triggering assertion.
Similar fix to
- commit 90b7f29617 ("net: usb: rtl8150: enable basic endpoint checking")
- commit 9e7021d2ae ("net: usb: catc: enable basic endpoint checking")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Ziyi Guo <n7l8m4@u.northwestern.edu>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260222050633.410165-1-n7l8m4@u.northwestern.edu
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 983512f3a8 ]
skb_may_tx_timestamp() may acquire sock::sk_callback_lock. The lock must
not be taken in IRQ context, only softirq is okay. A few drivers receive
the timestamp via a dedicated interrupt and complete the TX timestamp
from that handler. This will lead to a deadlock if the lock is already
write-locked on the same CPU.
Taking the lock can be avoided. The socket (pointed by the skb) will
remain valid until the skb is released. The ->sk_socket and ->file
member will be set to NULL once the user closes the socket which may
happen before the timestamp arrives.
If we happen to observe the pointer while the socket is closing but
before the pointer is set to NULL then we may use it because both
pointer (and the file's cred member) are RCU freed.
Drop the lock. Use READ_ONCE() to obtain the individual pointer. Add a
matching WRITE_ONCE() where the pointer are cleared.
Link: https://lore.kernel.org/all/20260205145104.iWinkXHv@linutronix.de
Fixes: b245be1f4d ("net-timestamp: no-payload only sysctl")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260220183858.N4ERjFW6@linutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f22c77ce49 ]
The pattern is to check the entire driver request space, not just
sizeof something unrelated.
Fixes: 40909f664d ("RDMA/efa: Add EFA verbs implementation")
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://patch.msgid.link/1-v1-83e918d69e73+a9-rdma_udata_rc_jgg@nvidia.com
Acked-by: Michael Margolin <mrgolin@amazon.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd80bd7105 ]
The function ionic_query_port() calls ib_device_get_netdev() without
checking the return value which could lead to NULL pointer dereference,
Fix it by checking the return value and return -ENODEV if the 'ndev' is
NULL.
Fixes: 2075bbe8ef ("RDMA/ionic: Register device ops for miscellaneous functionality")
Signed-off-by: Kamal Heib <kheib@redhat.com>
Link: https://patch.msgid.link/20260220222125.16973-2-kheib@redhat.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82aec772fc ]
msg passed to netconsole from the console subsystem is not guaranteed
to be nul-terminated. Before recent
commit 7eab73b186 ("netconsole: convert to NBCON console infrastructure")
the message would be placed in printk_shared_pbufs, a static global
buffer, so KASAN had harder time catching OOB accesses. Now we see:
printk: console [netcon_ext0] enabled
BUG: KASAN: slab-out-of-bounds in string+0x1f7/0x240
Read of size 1 at addr ffff88813b6d4c00 by task pr/netcon_ext0/594
CPU: 65 UID: 0 PID: 594 Comm: pr/netcon_ext0 Not tainted 6.19.0-11754-g4246fd6547c9
Call Trace:
kasan_report+0xe4/0x120
string+0x1f7/0x240
vsnprintf+0x655/0xba0
scnprintf+0xba/0x120
netconsole_write+0x3fe/0xa10
nbcon_emit_next_record+0x46e/0x860
nbcon_kthread_func+0x623/0x750
Allocated by task 1:
nbcon_alloc+0x1ea/0x450
register_console+0x26b/0xe10
init_netconsole+0xbb0/0xda0
The buggy address belongs to the object at ffff88813b6d4000
which belongs to the cache kmalloc-4k of size 4096
The buggy address is located 0 bytes to the right of
allocated 3072-byte region [ffff88813b6d4000, ffff88813b6d4c00)
Fixes: c62c0a17f9 ("netconsole: Append kernel version to message")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260219195021.2099699-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bae8a5d2e7 ]
When the FarSync T-series card is being detached, the fst_card_info is
deallocated in fst_remove_one(). However, the fst_tx_task or fst_int_task
may still be running or pending, leading to use-after-free bugs when the
already freed fst_card_info is accessed in fst_process_tx_work_q() or
fst_process_int_work_q().
A typical race condition is depicted below:
CPU 0 (cleanup) | CPU 1 (tasklet)
| fst_start_xmit()
fst_remove_one() | tasklet_schedule()
unregister_hdlc_device()|
| fst_process_tx_work_q() //handler
kfree(card) //free | do_bottom_half_tx()
| card-> //use
The following KASAN trace was captured:
==================================================================
BUG: KASAN: slab-use-after-free in do_bottom_half_tx+0xb88/0xd00
Read of size 4 at addr ffff88800aad101c by task ksoftirqd/3/32
...
Call Trace:
<IRQ>
dump_stack_lvl+0x55/0x70
print_report+0xcb/0x5d0
? do_bottom_half_tx+0xb88/0xd00
kasan_report+0xb8/0xf0
? do_bottom_half_tx+0xb88/0xd00
do_bottom_half_tx+0xb88/0xd00
? _raw_spin_lock_irqsave+0x85/0xe0
? __pfx__raw_spin_lock_irqsave+0x10/0x10
? __pfx___hrtimer_run_queues+0x10/0x10
fst_process_tx_work_q+0x67/0x90
tasklet_action_common+0x1fa/0x720
? hrtimer_interrupt+0x31f/0x780
handle_softirqs+0x176/0x530
__irq_exit_rcu+0xab/0xe0
sysvec_apic_timer_interrupt+0x70/0x80
...
Allocated by task 41 on cpu 3 at 72.330843s:
kasan_save_stack+0x24/0x50
kasan_save_track+0x17/0x60
__kasan_kmalloc+0x7f/0x90
fst_add_one+0x1a5/0x1cd0
local_pci_probe+0xdd/0x190
pci_device_probe+0x341/0x480
really_probe+0x1c6/0x6a0
__driver_probe_device+0x248/0x310
driver_probe_device+0x48/0x210
__device_attach_driver+0x160/0x320
bus_for_each_drv+0x101/0x190
__device_attach+0x198/0x3a0
device_initial_probe+0x78/0xa0
pci_bus_add_device+0x81/0xc0
pci_bus_add_devices+0x7e/0x190
enable_slot+0x9b9/0x1130
acpiphp_check_bridge.part.0+0x2e1/0x460
acpiphp_hotplug_notify+0x36c/0x3c0
acpi_device_hotplug+0x203/0xb10
acpi_hotplug_work_fn+0x59/0x80
...
Freed by task 41 on cpu 1 at 75.138639s:
kasan_save_stack+0x24/0x50
kasan_save_track+0x17/0x60
kasan_save_free_info+0x3b/0x60
__kasan_slab_free+0x43/0x70
kfree+0x135/0x410
fst_remove_one+0x2ca/0x540
pci_device_remove+0xa6/0x1d0
device_release_driver_internal+0x364/0x530
pci_stop_bus_device+0x105/0x150
pci_stop_and_remove_bus_device+0xd/0x20
disable_slot+0x116/0x260
acpiphp_disable_and_eject_slot+0x4b/0x190
acpiphp_hotplug_notify+0x230/0x3c0
acpi_device_hotplug+0x203/0xb10
acpi_hotplug_work_fn+0x59/0x80
...
The buggy address belongs to the object at ffff88800aad1000
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 28 bytes inside of
freed 1024-byte region
The buggy address belongs to the physical page:
page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0xaad0
head: order:3 mapcount:0 entire_mapcount:0 nr_pages_mapped:0 pincount:0
flags: 0x100000000000040(head|node=0|zone=1)
page_type: f5(slab)
raw: 0100000000000040 ffff888007042dc0 dead000000000122 0000000000000000
raw: 0000000000000000 0000000080100010 00000000f5000000 0000000000000000
head: 0100000000000040 ffff888007042dc0 dead000000000122 0000000000000000
head: 0000000000000000 0000000080100010 00000000f5000000 0000000000000000
head: 0100000000000003 ffffea00002ab401 00000000ffffffff 00000000ffffffff
head: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88800aad0f00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88800aad0f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88800aad1000: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff88800aad1080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff88800aad1100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Fix this by ensuring that both fst_tx_task and fst_int_task are properly
canceled before the fst_card_info is released. Add tasklet_kill() in
fst_remove_one() to synchronize with any pending or running tasklets.
Since unregister_hdlc_device() stops data transmission and reception,
and fst_disable_intr() prevents further interrupts, it is appropriate
to place tasklet_kill() after these calls.
The bugs were identified through static analysis. To reproduce the issue
and validate the fix, a FarSync T-series card was simulated in QEMU and
delays(e.g., mdelay()) were introduced within the tasklet handler to
increase the likelihood of triggering the race condition.
Fixes: 2f623aaf9f ("net: farsync: Fix kmemleak when rmmods farsync")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20260219124637.72578-1-duoming@zju.edu.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9af0feae80 ]
RoCE GID entries become stale when netdev properties change during the
IB device registration window. This is reproducible with a udev rule
that sets a MAC address when a VF netdev appears:
ACTION=="add", SUBSYSTEM=="net", KERNEL=="eth4", \
RUN+="/sbin/ip link set eth4 address 88:22:33:44:55:66"
After VF creation, show_gids displays GIDs derived from the original
random MAC rather than the configured one.
The root cause is a race between netdev event processing and device
registration:
CPU 0 (driver) CPU 1 (udev/workqueue)
────────────── ──────────────────────
ib_register_device()
ib_cache_setup_one()
gid_table_setup_one()
_gid_table_setup_one()
← GID table allocated
rdma_roce_rescan_device()
← GIDs populated with
OLD MAC
ip link set eth4 addr NEW_MAC
NETDEV_CHANGEADDR queued
netdevice_event_work_handler()
ib_enum_all_roce_netdevs()
← Iterates DEVICE_REGISTERED
← Device NOT marked yet, SKIP!
enable_device_and_get()
xa_set_mark(DEVICE_REGISTERED)
← Too late, event was lost
The netdev event handler uses ib_enum_all_roce_netdevs() which only
iterates devices marked DEVICE_REGISTERED. However, this mark is set
late in the registration process, after the GID cache is already
populated. Events arriving in this window are silently dropped.
Fix this by introducing a new xarray mark DEVICE_GID_UPDATES that is
set immediately after the GID table is allocated and initialized. Use
the new mark in ib_enum_all_roce_netdevs() function to iterate devices
instead of DEVICE_REGISTERED.
This is safe because:
- After _gid_table_setup_one(), all required structures exist (port_data,
immutable, cache.gid)
- The GID table mutex serializes concurrent access between the initial
rescan and event handlers
- Event handlers correctly update stale GIDs even when racing with rescan
- The mark is cleared in ib_cache_cleanup_one() before teardown
This also fixes similar races for IP address events (inetaddr_event,
inet6addr_event) which use the same enumeration path.
Fixes: 0df91bb673 ("RDMA/devices: Use xarray to store the client_data")
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20260127093839.126291-1-jiri@resnulli.us
Reported-by: syzbot+881d65229ca4f9ae8c84@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=881d65229ca4f9ae8c84
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3aa677625c ]
TIPC uses named table to store TIPC services represented by type and
instance. Each time an application calls TIPC API bind() to bind a
type/instance to a socket, an entry is created and inserted into the
named table. It looks like this:
named table:
key1, entry1 (type, instance ...)
key2, entry2 (type, instance ...)
In the above table, each entry represents a route for sending data
from one socket to the other. For all publications originated from
the same node, the key is UNIQUE to identify each entry.
It is calculated by this formula:
key = socket portid + number of bindings + 1 (1)
where:
- socket portid: unique and calculated by using linux kernel function
get_random_u32_below(). So, the value is randomized.
- number of bindings: the number of times a type/instance pair is bound
to a socket. This number is linearly increased,
starting from 0.
While the socket portid is unique and randomized by linux kernel, the
linear increment of "number of bindings" in formula (1) makes "key" not
unique anymore. For example:
- Socket 1 is created with its associated port number 20062001. Type 1000,
instance 1 is bound to socket 1:
key1: 20062001 + 0 + 1 = 20062002
Then, bind() is called a second time on Socket 1 to by the same type 1000,
instance 1:
key2: 20062001 + 1 + 1 = 20062003
Named table:
key1 (20062002), entry1 (1000, 1 ...)
key2 (20062003), entry2 (1000, 1 ...)
- Socket 2 is created with its associated port number 20062002. Type 1000,
instance 1 is bound to socket 2:
key3: 20062002 + 0 + 1 = 20062003
TIPC looks up the named table and finds out that key2 with the same value
already exists and rejects the insertion into the named table.
This leads to failure of bind() call from application on Socket 2 with error
message EINVAL "Invalid argument".
This commit fixes this issue by adding more port id checking to make sure
that the key is unique to publications originated from the same port id
and node.
Fixes: 218527fe27 ("tipc: replace name table service range array with rb tree")
Signed-off-by: Tung Nguyen <tung.quang.nguyen@est.tech>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260220050541.237962-1-tung.quang.nguyen@est.tech
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4cfe066a82 ]
The REF_PHASE_OFFSET_COMP register is 48-bit wide on most zl3073x chip
variants, but only 32-bit wide on chip IDs 0x0E30, 0x0E93..0x0E97 and
0x1F60. The driver unconditionally uses 48-bit read/write operations,
which on 32-bit variants causes reading 2 bytes past the register
boundary (corrupting the value) and writing 2 bytes into the adjacent
register.
Fix this by storing the chip ID in the device structure during probe
and adding a helper to detect the affected variants. Use the correct
register width for read/write operations and the matching sign extension
bit (31 vs 47) when interpreting the phase compensation value.
Fixes: 6287262f76 ("dpll: zl3073x: Add support to adjust phase")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260220155755.448185-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
