Factor out processing of special commands from ide_special_rq()
to ide_do_devset() and ide_do_park_unpark().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use elv_add_request() instead of __elv_add_request() in ide_do_drive_cmd().
* ide_do_drive_cmd() is used only in ide-{atapi,cd}.c so inline it there.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move ide_dma_timeout_retry() to ide-dma.c and add static inline
version for CONFIG_BLK_DEV_IDEDMA=n.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move drive_is_ready() to ide-io.c, then make it static.
Also make some minor CodingStyle fixups while at it.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* taskfile_load_raw() is used only by do_drive_set_taskfiles()
so inline it there.
While at it:
- rename 'args' variable to 'task'
- remove struct taskfile_array
- do ide_acpigtf check early
- use REGS_PER_GTF
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide_noacpi is already checked by ide_acpi_exec_tfs()
which is the only user of do_drive_set_taskfiles().
* ide_acpi_exec_tfs() prints sufficient debug info about the
device so no need to do it again.
* do_drive_get_GTF() + ide_acpi_exec_tfs() make sure that this
function will never be called with incorrect gtf_length argument
or if device is not present.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide_noacpi is already checked by ide_acpi_exec_tfs()
which is the only user of do_drive_get_GTF().
* ide_acpi_exec_tfs() prints sufficient debug info about the
device so no need to have excessive data about port/host.
* It is sufficient to check for drive->acpidata->obj_handle
as it will be NULL if dev == NULL or hwif->acpidata == NULL
or device is not present.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide_acpi_init() -> ide_acpi_init_port()
* ide_acpi_blacklist() -> ide_acpi_init()
* Call ide_acpi_init() only once (do it during IDE core
initialization) and cleanup the function accordingly.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_for_each_present_dev() iterator and convert IDE code to use it.
* Do some drive-by CodingStyle fixups in ide-acpi.c while at it.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Init ACPI handles for devices in ide_acpi_port_init_devices()
and remove no longer needed ide_acpi_drive_get_handle().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Then make it static and remove 'dma' argument.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* IDE_DFLAG_NO_IO_32BIT may be set by cmd640's ->init_dev method
so don't clear it in ide_port_tune_devices() (+ no need to do it).
* Move IDE_DFLAG_NO_IO_32BIT handling to ide_port_init_devices().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Impact: cleanup, new schedstat ABI
Since they are used on in statistics and are always set to zero, the
following fields from struct rq have been removed: yld_exp_empty,
yld_act_empty and yld_both_empty.
Both Sched Debug and SCHEDSTAT_VERSION versions has also been
incremented since ABIs have been changed.
The schedtop tool has been updated to properly handle new version of
schedstat:
http://rt.wiki.kernel.org/index.php/Schedtop_utility
Signed-off-by: Luis Henriques <henrix@sapo.pt>
Acked-by: Gregory Haskins <ghaskins@novell.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20090324221002.GA10061@hades.domain.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix the tracepoint documentation to refer to "tracepoint-sample"
instead of "tracepoint-example" to match what actually exists;
fix the directory, and clarify how to compile.
Change every instance of "example" in the sample tracepoint code
to "sample" for consistency.
Signed-off-by: Jody McIntyre <scjody@sun.com>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: torvalds@linux-foundation.org
LKML-Reference: <20090324200027.GH8294@clouds>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The tracing header needs to include definitions for the macros used and
the types referenced. This lets automated tracing tools like SystemTap
make use of the tracepoint without any specific knowledge of its
meaning (leaving that to the user).
Signed-off-by: Josh Stone <jistone@redhat.com>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arches without efficient unaligned access can still perform a loop
assuming 16bit alignment in ifname_compare()
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: fix bug with irq-descriptor moving when logical flat
Rusty observed:
> The effect of setting desc->affinity (ie. from userspace via sysfs) has varied
> over time. In 2.6.27, the 32-bit code anded the value with cpu_online_map,
> and both 32 and 64-bit did that anding whenever a cpu was unplugged.
>
> 2.6.29 consolidated this into one routine (and fixed hotplug) but introduced
> another variation: anding the affinity with cfg->domain. Is this right, or
> should we just set it to what the user said? Or as now, indicate that we're
> restricting it.
Eric pointed out that desc->affinity should be what the user requested,
if it is at all possible to honor the user space request.
This bug got introduced by commit 22f65d31b "x86: Update io_apic.c to use
new cpumask API".
Fix it by moving the masking to before the descriptor moving ...
Reported-by: Rusty Russell <rusty@rustcorp.com.au>
Reported-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <49C94134.4000408@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This fixes a bug when setting the sdc_reg for 4-bit bus width
transactions.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds a new driver: sdhci-of. The driver is similar to
the sdhci-pci, it contains common probe code, and controller-specific
ops and quirks.
So far there are only Freescale eSDHC ops and quirks.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
FSL eSDHC controllers can support maximum block size up to 4096 bytes,
the MBL (Maximum Block Length) field in the capabilities register
extended by one bit, and is set to 0x3.
But the SDHCI core doesn't support blocks of 4096 bytes, and thus
forces blksz to the lowest value -- 512 bytes. With this patch we can
pin up the blksz to the maximum supported block size, i.e. 2048 bytes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
FSL eSDHC controllers losing signal/interrupt enable states after
reset, so we should re-enable them.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Small udelay is needed to make eSDHC work in PIO mode. Without
the delay reading causes endless interrupt storm, and writing
corrupts data. The first guess would be that we must wait for
some bit in some register, but I didn't find any reliable bits
that change before and after the delay.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
FSL eSDHC hosts have incompatible register map to manage the SDCLK.
This patch adds set_clock callback so that drivers could overwrite
set_clock behaviour.
Similar patch[1] was posted by Ben Dooks, though in Ben's version the
callback is named change_clock, plus the patch has some unrelated bits
that makes the patch difficult to reuse.
[1] http://lkml.org/lkml/2008/12/2/160
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some controllers do not provide clock information in their capabilities
(in the Samsung case, it is because there are multiple clock sources
available to the controller). Add hooks to allow the system to supply
clock information.
p.s.
In the original Ben's patch there was a bug that makes sdhci_add_host()
return -ENODEV even if callbacks were specified. This is fixed now.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds SDHCI_QUIRK_INVERTED_WRITE_PROTECT quirk. When
specified, the sdhci driver will invert WP state.
p.s. Actually, the quirk is more board-specific than
controller-specific.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds SDHCI_QUIRK_BROKEN_CARD_DETECTION quirk. When specified,
sdhci driver will set MMC_CAP_NEEDS_POLL MMC host capability, and won't
enable card insert/remove interrupts.
This is needed for hosts with unreliable card detection, such as FSL
eSDHC. The original eSDHC driver was tring to "debounce" card-detection
IRQs by reading present state and disabling particular interrupts. But
with this debouncing scheme I noticed that sometimes we miss card
insertion/removal events.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some hosts (that is, FSL eSDHC) throw PIO interrupts during DMA
transfers, this causes tons of unneeded interrupts, and thus highly
degraded speed.
This patch modifies the driver so that now we only enable relevant
(DMA or PIO) interrupts during transfers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Card detection interrupts should be handled separately as they should
not be enabled before mmc_add_host() returns and should be disabled
before calling mmc_remove_host(). The same is for suspend and resume
routines.
sdhci_init() no longer enables card-detection irqs. Instead, two new
functions implemented: sdhci_enable_card_detection() and
sdhci_disable_card_detection().
New sdhci_reinit() call implemented to behave the same way as the old
sdhci_init().
Also, this patch implements and uses few new helpers to manage IRQs in
a more conveinient way, that is:
- sdhci_clear_set_irqs()
- sdhci_unmask_irqs()
- sdhci_mask_irqs()
- SDHCI_INT_ALL_MASK constant
sdhci_enable_sdio_irq() converted to these new helpers, plus the
helpers will be used by the subsequent patches.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Currently the SDHCI driver works with PCI accessors (write{l,b,w} and
read{l,b,w}).
With this patch drivers may change memory accessors, so that we can
support hosts with "weird" IO memory access requirments.
For example, in "FSL eSDHC" SDHCI hardware all registers are 32 bit
width, with big-endian addressing. That is, readb(0x2f) should turn
into readb(0x2c), and readw(0x2c) should be translated to
le16_to_cpu(readw(0x2e)).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some cards are not able to send the data token in time, but
miss the time frame for some bits(!). So synchronize to the
start of the token.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
It is necessary to wait for bus power before sending
any commands.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Data transfers on third OMAP3 MMC controller don't work
because DMA line numbers are only defined for MMC1 and MMC2.
Fix that and store line numbers in mmc_omap_host structure
to reduce code size.
Tested on OMAP3 pandora board.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Turn off the bus power at suspend.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Allow slot_name to be the same as the other OMAP
driver, by removing the redundant "slot:" prefix.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Allow a cover switch to be used to cause a rescan of the
MMC slot.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Instead of using the bounce buffer, using scatter-gather emulation
(as in the OMAP1/2 MMC driver) removes the need of one extra memory
copy and improves performance.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some MMC commands result in the card becoming busy after
the response is received. This needs to be specified
for the omap_hsmmc host controller, which is what this
patch does. However, the effect is that some commands
with no data will cause a Transfer Complete (TC) interrupt
in addition to the Command Complete (CC) interrupt.
In order to deal with that, the irq handler has needed
a few changes also.
The benefit of this change is that the omap_hsmmc host
controller driver now waits for the TC interrupt while
the card is busy, so the mmc_block driver needs to poll
the card status just once instead of repeatedly.
i.e. the net result is more sleep and less cpu.
The command sequence for open-ended multi-block write
with DMA is now:
Issue write command CMD25
Receive CC interrupt
Data is sent
Receive TC interrupt (DMA is done)
Issue stop command CMD12
Receive CC interrupt
Card is busy
Receive TC interrupt
Card is now ready for next transfer
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>