GPIO31 and GPIO32 (CTS/RTS) are handled by the magnetometer and
shall not simultaneously be controlled by UART2.
Reported-by: Peter Nessrup <peter.nessrup@stericsson.com>
Signed-off-by: Jorgen Jonsson <jorgen.jonsson@stericsson.com>
Reviewed-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PCH platforms and VLV should map DPMS standby and suspend modes to off, but
due to a buggy reversed comparison this is done on pre-PCH platforms
instead.
Reported-by: Loïc Yhuel <loic.yhuel@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=56754
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add platform device id to check whether the SSC controller support
pdc or dam for data transfer
If match "at91rm9200_ssc", which support pdc for data transfer
If match "at91sam9g45_ssc", which support dma for data transfer
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch removes some code duplication by using module_platform_driver
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using the devm_xxx() managed function to stripdown the error
and remove code.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The commit d7b4394e[Cleanup the omap2_mcspi_txrx_dma function]
changed the wait_for_completion order. Move the wait so that the
rx doesnot wait for the tx to complete.
Reported-and-tested-by: Sørensen, Stefan <Sorensen@polycom.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes below build error when !CONFIG_OF_GPIO.
CC drivers/pinctrl/pinctrl-samsung.o
drivers/pinctrl/pinctrl-samsung.c: In function 'samsung_pinctrl_parse_dt_pins':
drivers/pinctrl/pinctrl-samsung.c:557:19: warning: unused variable 'prop' [-Wunused-variable]
drivers/pinctrl/pinctrl-samsung.c: In function 'samsung_gpiolib_register':
drivers/pinctrl/pinctrl-samsung.c:797:5: error: 'struct gpio_chip' has no member named 'of_node'
make[2]: *** [drivers/pinctrl/pinctrl-samsung.o] Error 1
make[1]: *** [drivers/pinctrl] Error 2
make: *** [drivers] Error 2
The samsung pinctrl driver supports only device tree enabled
platforms. Thus make PINCTRL_SAMSUNG depend on OF && GPIOLIB.
The reason to depend on GPIOLIB is CONFIG_OF_GPIO only available
when GPIOLIB is selected.
Since PINCTRL_EXYNOS4 select PINCTRL_SAMSUNG, thus also make
PINCTRL_EXYNOS4 depend on OF && GPIOLIB.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current FSI driver required set_rate() platform callback function
to set audio clock if it was master mode,
because it seemed that CPG/FSI-DIV clocks calculation depend on
platform/board/cpu.
But it was calculable regardless of platform.
This patch supports audio clock calculation method,
but the sampling rate under 32kHz is not supported at this point.
Old type set_rate() is still supported now,
but it will be deleted on next version
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When MCLK is supplied externally and BCLK and LRC are configured as outputs
(codec is master), the PLL values are only calculated correctly on the first
transmission. On subsequent transmissions, at differenct sample rates, the
wrong PLL values are used. Test for f_opclk instead of f_pllout to determine
if the PLL values are needed.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Fixed pointers' positions in the csr_wifi_hip_unifi_signal_names.c file
that were identifed by checkpatch.pl tool.
Signed-off-by: Hojung Youn <amoc.yn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed whitespace paddings in the csr_wifi_hip_unifi_signal_names.c file
that were, though, not identified by checkpatch.pl tool.
Signed-off-by: Hojung Youn <amoc.yn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed brackets' positions in the csr_wifi_hip_unifi_signal_names.c file
that were identified by checkpatch.pl tool. Some brackets are removed
which are not needed by the rule of CodingStyle documentation.
Signed-off-by: Hojung Youn <amoc.yn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed indent style in the csr_wifi_hip_unifi_signal_names.c
file that were identified by checkpatch.pl tool. All whitespaced
indents are converted into tab characters, except ones in the
topmost commentation.
Signed-off-by: Hojung Youn <amoc.yn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The header amcc_s5933.h is not needed. Remove the include.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This value is only needed for subdevices that support async commands.
The comedi core will default the value to 1 when it is not initialized.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The board supported by this driver can generate an interrupt based
on the state of input channels 0-15.
The apci1032_intr_insn_config() function is used to configure which
inputs are used to generate the interrupt. Currently this function
is broken since it does not follow the comedi API for insn_config
functions. Fix this function by implementing the, currently unused,
config instruction INSN_CONFIG_DIGITAL_TRIG.
Add the remaining subdevice operations necessary for the interrupt
subdevice to support async commands.
Fix the subdevice initialization so that if the interrupt is not
available the subdevice is set as COMEDI_SUBD_UNUSED.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The addi-data drivers use send_sig() to let the user know when an
interrupt has occurred. The "standard" way to do this in the comedi
subsystem is to have a subdevice that supports asynchronous commands
and use comedi_event() to signal the user.
Remove the send_sig() usage in this driver. This also allows removing
the dev->private usage since tsk_Current was the only member still
being used in the private data.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This board supports a single interrupt that can be generated by an AND/OR
combination of 16 of the input channels.
Create a separate subdevice, similar to the comedi_parport driver, to
handle this interrupt.
Move the i_APCI1032_ConfigDigitalInput() operation from the digital
input subdevice to this new subdevice. Rename the CamelCase function
to apci1032_intr_insn_config().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge the remaining code from hwdrv_apci1032.c into the driver and
delete the now unused file.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need for this function to call v_APCI1032_Interrupt()
in hwdrv_apci1032.c to reset the board. Just move the code from
v_APCI1032_Interrupt() directly into this function.
Rename the CamelCase function to apci1032_interrupt().
Rename the CamelCase local variable used to read/write the control
register.
Change the return from IRQ_RETVAL(1) to IRQ_HANDLED.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is only one subdevice used in the driver. Remove the unused
subdevice init and only allcoate space for the one used.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move this function from hwdrv_apci1032.c.
Remove the unnecessary comment and rename the CamelCase function to
apci1032_di_insn_bits().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is the insn_read operation for the digital input subdevice.
This operation can be emulated by the comedi core now that the insn_bits
operation follows the comedi API. Remove this now unnecessary function.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is the insn_bits operation for the digital input subdevice.
According to the comedi API it's supposed return the status of the inputs
in data[1]. The addi-drivers abuse the API and try to make it conform to
their own use.
Fix this function so it follows the comedi API.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move this function from hwdrv_apci1032.c.
Remove the unnecessary comment and rename the CamelCase function to
apci1032_reset().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For aesthetic reasons, rename the defines used for the register map
so they are a bit shorter.
Define, and use, the bits in the interrupt control register.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver supports only one boardtype. Since this driver uses the
comedi auto attach mechanism, the information left in the boaridnfo
is not required to attach this driver to the comedi subsystem.
Remove the boardinfo data and its use in the driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the boardinfo about the 'interrupt' function and just call
it directly.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that this driver is separate from the "common" addi-data code,
the eeprom does not contain any information required to make this
driver work.
Remove the unneeded initalization of the 's_EeParameters' and the
code that reads the eeprom to fill in the parameters.
Also, since reading the eeprom is not really interesting, remove
the EEPROM subdevice.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI bar 3 is not used by this driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, devpriv->iobase is used to hold the PCI bar 2 base address
used to read/write the registers on the board. The same information
is stored in the comedi_device dev->iobase. Use that instead.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This boardinfo is no longer required by the driver. Remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This board does not use the ioremap'ed PCI bar 3 memory address.
Remove the ioremap and iounmap of that region.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This board has a 93c76 eeprom. Knowing this information allows
simplifying the code that reads the PCI bars to get the iobase
addresses used in the driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This board always has 32 digital inputs. Remove the test when
initializing the subdevice.
Also, since this board is the only one supported by this driver,
remove the boardinfo about the digital inputs and just use the
data directly in the subdevice init.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This board does not have analog outputs. Remove the subdevice init for
them.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This board does not have analog inputs. Remove the subdevice init for
them.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This board does not have digital outputs. Remove the subdevice init for
them.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This board does not have a timer. Remove the subdevice init for it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This board does not have ttl i/o. Remove the subdevice init for
it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver is now separate from the "common" code used with the
addi-data drivers. There is no need to use i_ADDI_Reset() to call
the correct "reset" function.
Remove the i_ADDI_Reset() function and the 'reset' pointer to the
real function from the boardinfo and just call the function directly
where needed.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The addi_apci_1032 driver is a simple digital input board with 32
optically isolated inputs. Using the addi-data "common" code introduces
a lot of bloat.
Copy the code in addi_common.c to this driver and remove the #include
that caused addi_common.c to be compiled with this driver. This will
allow removing the special handling for allocating and freeing the
dma buffers in the common code.
Rename the attach_pci and detach functions so they have namespace
associated with this driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the comedi driver comment to reflect the fact that manual
attachment of devices is no longer supported. Also replace the request
to file a bug report about unidentified PCI device IDs with a request to
let the maintainers know about such devices.
Reformat the comment using the usual block comment style.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move `disable_plx_interrupts()`, `disable_ai_interrupts()`,
`enable_ai_interrupts()`, `set_ai_fifo_segment_length()`,
`set_ai_fifo_size()`, `ai_fifo_size()`, `load_ao_dma_buffer()`, and
`load_ao_dma()`, and remove forward declarations of these functions.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move `cb_pcidas64_find_pci_board()`, `auto_attach()` and `detach()` and
remove the forward declaration of `setup_subdevices()`.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
