Move `setup_subdevices()` and remove a load of forward declarations.
Added a forward declaration of `setup_subdevices()` temporarily.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The `board(dev)` inline function returns `dev->board_ptr` cast from
`const void *` to `struct pcidas64_board *`. It really ought to return
a `const struct pcidas64_board *`. Rather than fix the function, just
remove it and replace the calls with a local variable `thisboard` in the
functions that call it. `thisboard` is set to the result of the common
inline function `comedi_board(dev)` defined in "comedidev.h".
Fix a little resulting fall-out from the inline function
`ai_dma_ring_count(board)` whose parameter should have been a const
pointer.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The inline function `comedi_board(dev)` merely returns `dev->board_ptr`.
It does not modify any members of `*dev` so make its parameter a const
pointer.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some whitespace changes, mostly to fix lines > 80 characters and
operator placement. Add/remove some braces according to CodingStyle.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace `printk` calls with something else. For the `DEBUG_PRINT()`
macro, use `pr_debug()` (if `PCIDAS64_DEBUG macro defined) or
`no_printk()`.
Fix a few `DEBUG_PRINT()` calls due to compiler warnings and add
newlines where they are missing.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver does not need to support manual attachment of supported PCI
devices. Replace the `attach()` hook with an `auto_attach()` hook.
This will be called via `comedi_pci_auto_config()` at PCI probe time.
The `auto_attach()` calls new function `cb_pcidas64_find_pci_board()` to
find the correct entry in `pcidas64_boards[]` for the PCI device.
This driver no longer increments the PCI reference count during
attachment, so remove the call to `pci_dev_put()` when detaching the
device.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the boot_done counter variable and check the wm0010 state
variable instead.
Signed-off-by: Scott Ling <scott.ling@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We are using S3C_EINT(4) instead of S3C_EINT(5).
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
SH7372 can use DMA with the FLCTL flash controller. Add required slave
IDs and slave descriptors.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
This patch is required from R-Car I2C driver
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
r8a7740 machine desc name should be R8A7740,
not SH7372
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
We can remove the extra code of modify_scu_cpu_psr() and use the cleaner
generic ARM helper scu_power_mode(). As every CPU only deals with its
own power register and scu_power_mode() operates with 8-bit accesses,
we save the locking overhead too.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
We can remove the extra code of modify_scu_cpu_psr() and use the cleaner
generic ARM helper scu_power_mode(). As every CPU only deals with its
own power register and scu_power_mode() operates with 8-bit accesses,
we save the locking overhead too.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
We can remove the extra code of modify_scu_cpu_psr() and use the cleaner
generic ARM helper scu_power_mode(). As every CPU only deals with its
own power register and scu_power_mode() operates with 8-bit accesses,
we save the locking overhead too.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
This is old CPU of shmobile, and the machine by which this CPU is
used cannot be obtained.
Therefore, remove SH7377 support.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
This is old CPU of shmobile, and the machine by which this CPU is
used cannot be obtained.
Therefore, remove SH7367 support.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
The script still spits out an error ("Can't read private key") but we
don't break modules_install.
Reported-by: Bruno Wolff III <bruno@wolff.to>
Original-patch-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
commit 24d7b40a (ARM: OMAP2+: PM: MPU DVFS: use generic CPU device for
MPU-SS) updated the regulator name used for the MPU regulator, but only
updated OMAP3, not OMAP4. Fix the OMAP4 name as well, otherwise CPUfreq
fails to find the MPU regulator.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Commit 2dcfaf85 mistakenly dropped the "flags & PCI_EXP_FLAGS_SLOT" test,
so now we create hotplug slots even for PCIe port devices that don't
support hotplug. This patch fixes this problem.
[bhelgaas: changelog]
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Jiang Liu <jiang.liu@huawei.com>
* pci/huang-d3cold-fixes:
PCI/PM: Fix proc config reg access for D3cold and bridge suspending
PCI/PM: Resume device before shutdown
PCI/PM: Fix deadlock when unbinding device if parent in D3cold
Add OMAP4460 OPP definitions for voltage and frequencies based on
OMAP4460 ES1.0 DM Operating Condition Addendum Version 0.1
The following exceptions are present:
* Smartreflex support is still on experimental mode: the gains and min
limits are currently pending characterization data. Currently OMAP4430 values
are used.
* Efuse offset for core OPP100-OV setting is not clear in documentation.
* IVA OPPs beyond OPP100 are disabled due to the delta between max OMAP4460
current requirements and Phoenix Max supply on VCORE2 in the default
configuration - boards which have supply which can support this should
explicitly call opp_enable and enable the same.
* MPU OPPs > OPPTURBO can easily be detected using a efuse burnt - currently
disabled pending clock changes to support DCC feature.
[nm@ti.com: cleanups and updates from Datamanual]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
[t-kristo@ti.com: rebased to linux-3.6-rc5]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
With the new parameters, I2C can now be put to high speed mode for
better performance.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
VC code now provides a table of pre-calculated I2C setup parameters,
which will be used based on the capacitance value calculated for the I2C
trace on the PCB. A default trace length of 6.3cm is used unless board
defines its own value during init. The parameters set will be the I2C
internal pull setup and the I2C timing parameters for high speed use
mode. Full speed mode is not supported as of now.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
RACEN bit should only be set if the voltage and command register addresses
are the same.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This is no longer needed as the ramp times are calculated from
voltage deltas + slew rates.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
As vddmin / vddmax voltages for the pmic only describe the pmic
capabilities now, change the voltages to be according to spec.
TWL data manuals give following values:
TWL4030 (SWCS019L) : VDD1: 600mV ... 1450mV, VDD2: 600mV ... 1500mV
TWL5030 (SWCS030E) : VDD1: 600mV ... 1450mV, VDD2: 600mV ... 1500mV
TWL6030 (SWCS045A) : 0V ... 2100mV
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
We now use the previously defined oscillator setup / shutdown times
to calculate the register values for CLKSETUP.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Now we select the vddmin and vddmax values based on both pmic and
voltage processor data, this allows usage of different power ICs.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This contains startup and shutdown times for the oscillator. By default
use ULONG_MAX. Oscillator setup is used for calculating and setting up
latencies for sleep modes that disable oscillator.
Based on a patch from Nishanth Menon <nm@ti.com>.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
OMAP4 VC code now uses voltage deltas + slew rates for calculating
actual ramp times for voltage changes. Both retention / sleep +
off mode voltage ramp times are setup at the same time during
initialization.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
OMAP4 has two VOLTSETUP registers. One is controlling retention and
sleep voltage setup times, the other one off mode setup times. Both
of these need to be setup for stable behavior of the device.
The code setting up the new register will be added in the next
patch.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
We used to add the _PRT after enumerating devices behind a new host
bridge. This moves the _PRT addition *before* the enumeration, since
it no longer depends on the struct pci_bus existing. This is one
step towards consolidating the .add/.start methods.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Taku Izumi <izumim.taku@jp.fujitsu.com>
OMAP3 VC code now uses voltage deltas + slew rates for calculating actual
ramp times for voltage changes. Previously a static value was used.
Two calculation methods are provided: i2c_timings and off_timings.
I2C timings are used during retention or off mode transition which
is initiated over I2C, and OFF timings are used if PMIC signal
(nsleep) is used to control all the off mode voltages at the same time.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
These new structs will hold the sleep voltage levels (omap_vc_params)
and voltage processor min / max voltages (omap_vp_params.) Previously
these were part of the PMIC struct, but they do not really belong there,
as they are OMAP chip specific, not PMIC specific parameters. voltdm
code is also changed to use the new structs.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
These are now called vddmin and vddmax, as these fields will be used
globally for selecting voltage ranges for a pmic channel, and not
only for voltage processor.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Every PMIC has it's own eccentricities, For example, one of the
PMIC has MSB set to 1 for a specific function - voltage enable!
using an hardcoded value specific for TWL when copied over to
such an implementation causes the system to crash as the MSB bit
was 0 and the voltage got disabled!.
Instead we use actual values and depend on the convertion routines
to abstract out the eccentricities of each PMIC.
With this, we can now move the voltages to a common location in
voltage.h as they are no longer dependent on PMICs and expect the
PMIC's conversion routines to set a cap if the voltage is out of
reach for the PMIC.
Reported-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This effectively reverts 859a3f86ca ("ACPI: simplify
acpi_pci_irq_add_prt() API") and d9efae3688 ("ACPI: simplify
acpi_pci_irq_del_prt() API").
The reason is to disentangle these routines from the struct pci_bus.
We want to be able to add the _PRT before the struct pci_bus
exists, and delete the _PRT after we've removed the pci_bus.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
This patch adds support for TI's ADC driver.
This is a multifunctional device.
Analog input lines are provided on which
voltage measurements can be carried out.
You can have upto 8 input lines.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch converts touchscreen into a MFD client.
All the register definitions, clock initialization,
etc has been moved to MFD core driver.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add the mfd core driver which supports touchscreen
and ADC.
With this patch we are only adding infrastructure to
support the MFD clients.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Make way for addition of MFD driver.
The existing touchsreen driver is a MFD client.
For better readability we rename the file to
indicate its functionality as only touchscreen.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The touchscreen IP uses level sensitive interrupts rather
than edge sensitive interrupts and therefore the is no need
to use the EOI register to have the module re-strobe the
interrupt line if there pending interrupts exist.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Code currently uses FIFO1 threshold interrupt.
since this is a MFD, Dedicating FIFO0 to touchscreen
and making way for other devices to use FIFO1 as well.
The FIFO can be shared between 2 devices but since the
interrupt used is threshold interrupt on FIFO1, we would
end up having wrong interrupts. Hence changing the same.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There are 16 programmable Step Configuration
registers which are used by the sequencer.
Program the Steps in order to configure a channel
input to be sampled. If the same step is applied
several times, the coordinate values read are more
accurate.
Hence we provide the user an option of how many steps
should be configured.
For ex: If this value is assigned as 4, This means that
4 steps are applied to read x co-ordinate and 4 steps to read
y co-ordinate. Furtheron the interrupt handler already
holds code to use delta filter and report the best value
out of these values to the input sub-system.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch cleans up the wrong register definitions
and usage for touchscreen controller.
Bit masks were not defined earlier.
For ex: consider a register define as:
write(xyz, ABC)
ABC is expected to be written to register bits 0-11.
Here we see that value written is as expected, but this write
is also affecting all the remaining bits of xyz.
The remaining bits hold the default value as 0 and the write
also sets it to zero. Hence wrong usage were not causing user
visible bugs.
Due to these reasons it was difficult to follow when
compared with TRM.
Unused definitions are also removed.
Since there is change in some naming convention because of
all the above mentioned reasons, the same has been
updated throughout the code.
Bit declarations are grouped to increase readability.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
'Workaround for ROM bug because of CA9 r2pX gic control'
register change disables the gic distributor while the secondary
cpu is being booted. If a localtimer interrupt on the primary cpu
occurs when the distributor is turned off, the interrupt is lost,
and the localtimer never fires again.
Make the primary cpu wait for the secondary cpu to reenable the
gic distributor (with interrupts off for safety), and then
check if the pending bit is set in the localtimer but not the
gic. If so, ack it in the localtimer, and reset the timer with
the minimum timeout to trigger a new timer interrupt.
Signed-off-by: Colin Cross <ccross@android.com>
[s-jan@ti.com: adapted to k3.4 + validated functionality]
Signed-off-by: Sebastien Jan <s-jan@ti.com>
[t-kristo@ti.com: dropped generic ARM kernel exports from the code, rebased
to mainline]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On OMAP4+ devices, GIC register context is lost when MPUSS hits
the OSWR(Open Switch Retention). On the CPU wakeup path, ROM code
gets executed and one of the steps in it is to restore the
saved context of the GIC. The ROM Code GIC distributor restoration
is split in two parts: CPU specific register done by each CPU and
common register done by only one CPU.
Below is the abstract flow.
...............................................................
- MPUSS in OSWR state.
- CPU0 wakes up on the event(interrupt) and start executing ROM code.
[..]
- CPU0 executes "GIC Restoration:"
[...]
- CPU0 swicthes to non-secure mode and jumps to OS resume code.
[...]
- CPU0 is online in OS
- CPU0 enables the GIC distributor. GICD.Enable Non-secure = 1
- CPU0 wakes up CPU1 with clock-domain force wakeup method.
- CPU0 continues it's execution.
[..]
- CPU1 wakes up and start executing ROM code.
[..]
- CPU1 executes "GIC Restoration:"
[..]
- CPU1 swicthes to non-secure mode and jumps to OS resume code.
[...]
- CPU1 is online in OS and start executing.
[...] -
GIC Restoration: /* Common routine for HS and GP devices */
{
if (GICD != 1) { /* This will be true in OSWR state */
if (GIC_SAR_BACKUP_STATE == SAVED)
- CPU restores GIC distributor
else
- reconfigure GIC distributor to boot values.
GICD.Enable secure = 1
}
if (GIC_SAR_BACKUP_STATE == SAVED)
- CPU restore its GIC CPU interface registers if saved.
else
- reconfigure its GIC CPU interface registers to boot
values.
}
...............................................................
So as mentioned in the flow, GICD != 1 condition decides how
the GIC registers are handled in ROM code wakeup path from
OSWR. As evident from the flow, ROM code relies on the entire
GICD register value and not specific register bits.
The assumption was valid till CortexA9 r1pX version since there
was only one banked bit to control secure and non-secure GICD.
Secure view which ROM code sees:
bit 0 == Enable Non-secure
Non-secure view which HLOS sees:
bit 0 == Enable secure
But GICD register has changed between CortexA9 r1pX and r2pX.
On r2pX GICD register is composed of 2 bits.
Secure view which ROM code sees:
bit 1 == Enable Non-secure
bit 0 == Enable secure
Non-secure view which HLOS sees:
bit 0 == Enable Non-secure
Hence on OMAP4460(r2pX) devices, if you go through the
above flow again during CPU1 wakeup, GICD == 3 and hence
ROM code fails to understand the real wakeup power state
and reconfigures GIC distributor to boot values. This is
nasty since you loose the entire interrupt controller
context in a live system.
The ROM code fix done on next OMAP4 device (OMAP4470 - r2px) is to
check "GICD.Enable secure != 1" for GIC restoration in OSWR wakeup path.
Since ROM code can't be fixed on OMAP4460 devices, a work around
needs to be implemented. As evident from the flow, as long as
CPU1 sees GICD == 1 in it's wakeup path from OSWR, the issue
won't happen. Below is the flow with the work-around.
...............................................................
- MPUSS in OSWR state.
- CPU0 wakes up on the event(interrupt) and start executing ROM code.
[..]
- CPU0 executes "GIC Restoration:"
[..]
- CPU0 swicthes to non-secure mode and jumps to OS resume code.
[..]
- CPU0 is online in OS.
- CPU0 does GICD.Enable Non-secure = 0
- CPU0 wakes up CPU1 with clock domain force wakeup method.
- CPU0 waits for GICD.Enable Non-secure = 1
- CPU0 coninues it's execution.
[..]
- CPU1 wakes up and start executing ROM code.
[..]
- CPU1 executes "GIC Restoration:"
[..]
- CPU1 swicthes to non-secure mode and jumps to OS resume code.
[..]
- CPU1 is online in OS
- CPU1 does GICD.Enable Non-secure = 1
- CPU1 start executing
[...]
...............................................................
With this procedure, the GIC configuration done between the
CPU0 wakeup and CPU1 wakeup will not be lost but during this
short windows, the CPU0 will not receive interrupts.
The BUG is applicable to only OMAP4460(r2pX) devices.
OMAP4470 (also r2pX) is not affected by this bug because
ROM code has been fixed.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
