The array bpq_eth_addr is only used to get the size of an
address, whereas the bcast_addr is used to set the broadcast
address. This leads to a warning when using clang:
drivers/net/hamradio/bpqether.c:94:13: warning: variable 'bpq_eth_addr' is not
needed and will not be emitted [-Wunneeded-internal-declaration]
static char bpq_eth_addr[6];
^
Remove both variables and use the common eth_broadcast_addr
to set the broadcast address.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
lockdep spotted that we are using rfs_h.lock in enic_get_rxnfc() without
initializing. rfs_h.lock is initialized in enic_open(). But ethtool_ops
can be called when interface is down.
Move enic_rfs_flw_tbl_init to enic_probe.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 18 PID: 1189 Comm: ethtool Not tainted 4.17.0-rc7-devel+ #27
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-20171110_100015-anatol 04/01/2014
Call Trace:
dump_stack+0x85/0xc0
register_lock_class+0x550/0x560
? __handle_mm_fault+0xa8b/0x1100
__lock_acquire+0x81/0x670
lock_acquire+0xb9/0x1e0
? enic_get_rxnfc+0x139/0x2b0 [enic]
_raw_spin_lock_bh+0x38/0x80
? enic_get_rxnfc+0x139/0x2b0 [enic]
enic_get_rxnfc+0x139/0x2b0 [enic]
ethtool_get_rxnfc+0x8d/0x1c0
dev_ethtool+0x16c8/0x2400
? __mutex_lock+0x64d/0xa00
? dev_load+0x6a/0x150
dev_ioctl+0x253/0x4b0
sock_do_ioctl+0x9a/0x130
sock_ioctl+0x1af/0x350
do_vfs_ioctl+0x8e/0x670
? syscall_trace_enter+0x1e2/0x380
ksys_ioctl+0x60/0x90
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x5a/0x170
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joel Stanley says:
====================
Slience NCSI logging
v2:
Fix indent issue and commit message based on Joe's feedback
Add Sam's acks
Here are three changes to silence unnecessary warnings in the ncsi code.
The final patch adds Sam as the maintainer for NCSI.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sam has been handing the maintenance of NCSI for a number release cycles
now.
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves all of the netdev_printk(KERN_DEBUG, ...) messages over to
netdev_dbg.
As Joe explains:
> netdev_dbg is not included in object code unless
> DEBUG is defined or CONFIG_DYNAMIC_DEBUG is set.
> And then, it is not emitted into the log unless
> DEBUG is set or this specific netdev_dbg is enabled
> via the dynamic debug control file.
Which is what we're after in this case.
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This does not provide useful information. As the ncsi maintainer said:
> either we get a channel or broadcom has gone out to lunch
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In normal operation we see this series of messages as the host drives
the network device:
ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state down
ftgmac100 1e660000.ethernet eth0: NCSI: suspending channel 0
ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0
ftgmac100 1e660000.ethernet eth0: NCSI: channel 0 link down after config
ftgmac100 1e660000.ethernet eth0: NCSI interface down
ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state up
ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0
ftgmac100 1e660000.ethernet eth0: NCSI interface up
ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state down
ftgmac100 1e660000.ethernet eth0: NCSI: suspending channel 0
ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0
ftgmac100 1e660000.ethernet eth0: NCSI: channel 0 link down after config
ftgmac100 1e660000.ethernet eth0: NCSI interface down
ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state up
ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0
ftgmac100 1e660000.ethernet eth0: NCSI interface up
This makes all of these messages netdev_dbg. They are still useful to
debug eg. misbehaving network device firmware, but we do not need them
filling up the kernel logs in normal operation.
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using skb_reserve(skb, I40E_SKB_PAD + (xdp->data - xdp->data_hard_start))
is clearly wrong since I40E_SKB_PAD already points to the offset where
the original xdp->data was sitting since xdp->data_hard_start is defined
as xdp->data - i40e_rx_offset(rx_ring) where latter offsets to I40E_SKB_PAD
when build skb is used.
However, also before cc5b114dcf ("bpf, i40e: add meta data support")
this seems broken since bpf_xdp_adjust_head() helper could have been used
to alter headroom and enlarge / shrink the frame and with that the assumption
that the xdp->data remains unchanged does not hold and would push a bogus
packet to upper stack.
ixgbe got this right in 9247080816 ("ixgbe: add XDP support for pass and
drop actions"). In any case, fix it by removing the I40E_SKB_PAD from both
skb_reserve() and truesize calculation.
Fixes: cc5b114dcf ("bpf, i40e: add meta data support")
Fixes: 0c8493d90b ("i40e: add XDP support for pass and drop actions")
Reported-by: Keith Busch <keith.busch@linux.intel.com>
Reported-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Tested-by: Keith Busch <keith.busch@linux.intel.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru says:
====================
qed*: Fix series.
The patch series fixes few issues in the qed/qede drivers.
Please consider applying this series to "net".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not advertise DCBX_LLD_MANAGED capability i.e., do not allow
external agent to manage the dcbx/lldp negotiation. MFW acts as lldp agent
for qed* devices, and no other lldp agent is allowed to coexist with mfw.
Also updated a debug print, to not to display the redundant info.
Fixes: a1d8d8a51 ("qed: Add dcbnl support.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid calling a SIMD fastpath handler if it is NULL. The check is needed
to handle an unlikely scenario where unsolicited interrupt is destined to
a PF in INTa mode.
Fixes: fe56b9e6a ("qed: Add module with basic common support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory for packet buffers need to be freed in the error paths as there is
no consumer (e.g., upper layer) for such packets and that memory will never
get freed.
The issue was uncovered when port was attacked with flood of isatap
packets, these are multicast packets hence were directed at all the PFs.
For foce PF, this meant they were routed to the ll2 module which in turn
drops such packets.
Fixes: 0a7fb11c ("qed: Add Light L2 support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a private pointer to struct iomap to allow filesystems to pass data
from iomap_begin to iomap_end. Will be used by gfs2 for passing on the
on-disk inode buffer head.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Simply use iomap_apply to iterate over the file and a submit a bio for
each non-uptodate but mapped region and zero everything else. Note that
as-is this can not be used for file systems with a blocksize smaller than
the page size, but that support will be added later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
This will be used by gfs2 to attach data to transactions for the journaled
data mode. But the concept is generic enough that we might be able to
use it for other purposes like encryption/integrity post-processing in the
future.
Based on a patch from Andreas Gruenbacher.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Add generic inline data handling by adding a pointer to the inline data
region to struct iomap. When handling a buffered IOMAP_INLINE write,
iomap_write_begin will copy the current inline data from the inline data
region into the page cache, and iomap_write_end will copy the changes in
the page cache back to the inline data region.
This doesn't cover inline data reads and direct I/O yet because so far,
we have no users.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
[hch: small cleanups to better fit in with other iomap work]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
According to xfstest generic/240, applications seem to expect direct I/O
writes to either complete as a whole or to fail; short direct I/O writes
are apparently not appreciated. This means that when only part of an
asynchronous direct I/O write succeeds, we can either fail the entire
write, or we can wait for the partial write to complete and retry the
remaining write as buffered I/O. The old __blockdev_direct_IO helper
has code for waiting for partial writes to complete; the new
iomap_dio_rw iomap helper does not.
The above mentioned fallback mode is needed for gfs2, which doesn't
allow block allocations under direct I/O to avoid taking cluster-wide
exclusive locks. As a consequence, an asynchronous direct I/O write to
a file range that contains a hole will result in a short write. In that
case, wait for the short write to complete to allow gfs2 to recover.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
In iomap_to_bh, not only mark buffer heads in IOMAP_UNWRITTEN maps as
new, but also buffer heads in IOMAP_MAPPED maps with the IOMAP_F_NEW
flag set. This will be used by filesystems like gfs2, which allocate
blocks in iomap->begin.
Minor corrections to the comment for IOMAP_UNWRITTEN maps.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Bits of the buffer.c based write_end implementations that don't know
about buffer_heads and can be reused by other implementations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Andreas Gruenbacher <agruenba@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
ftrace_graph_caller was never run after calling ftrace_trace_function,
breaking the function graph tracer. Fix this, bringing it in line with the
x86 implementation.
While we're at it, also streamline the control flow of _mcount a bit to
reduce the number of branches.
This issue was reported before:
https://www.linux-mips.org/archives/linux-mips/2014-11/msg00295.html
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Tested-by: Matt Redfearn <matt.redfearn@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/18929/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: stable@vger.kernel.org # v3.17+
Instead of first allocating and then freeing memory for struct resource in
case we cannot parse a PCI resource from the device tree, work against a
local struct and kmemdup() it when we decide to go with it.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
I've stopped actively maintaining this driver for quite some time
already, and at91 maintainers are doing a good job at maintaining it.
Remove the AT91 clk driver entry so that the driver automatically
falls under the "ARM/Microchip (AT91) SoC support" entry.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
get_monotonic_boottime() is deprecated, so let's convert this to
the simpler ktime_get_boot_ns().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Put all relevant checks for transport domain in the
mlx5_ib_alloc/dealloc_transport_domain functions.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The file creation time in the inode uses time_t which is defined
differently on 32-bit and 64-bit architectures and deprecated. The
representation in the inode uses an unsigned 32-bit number, but this
gets wrapped around after year 2038 when assigned to a time_t.
This changes the type to time64_t, so we can support the full range of
timestamps between 1970 and 2106 on 32-bit systems like we do on 64-bit
systems already, and matching what we do for the atime/ctime/mtime stamps
since the introduction of 64-bit timestamps in VFS.
Note: the otime stamp is not actually used anywhere at the moment in
the kernel, it is just set when writing a file, so none of this really
makes a difference unless we implement setting the btime field in the
getattr() callback.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Even BOs with AMDGPU_GEM_CREATE_NO_CPU_ACCESS may end up at least
partially in CPU visible VRAM, in particular when all VRAM is visible.
v2:
* Don't take VRAM mgr spinlock, not needed (Christian König)
* Make loop logic simpler and clearer.
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Preparation for the following fix, no functional change intended.
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
At least in theory, ttm_bo_validate may move the BO, in which case the
pin_size accounting would be inconsistent with when the BO was pinned.
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit adds support for MOTU Traveler, launched in 2005, discontinued
quite before. As a result, transmission of PCM frame and MIDI messages is
available via ALSA PCM and RawMIDI/Sequencer interfaces.
This model supports sampling transmission frequency up to 192.0 kHz, and
AES/EBU on XLR interface and ADAT on optical interface. Unlike
Motu 828MkII, Windows driver can switch fetching mode for DSP, like
mute/unmute feature.
Although this commit enables high sampling transmission frequency, actual
sound from this model is not good. As long as I tested, it's silence at
176.4 kHz, and it includes hissing noise at 192.0 kHz. In my opinion, as I
reported at 3526ce7f9ba7 ('ALSA: firewire-motu: add MOTU specific protocol
layer'), timestamping on source packet header (SPH) may not still be good
for this model as well.
$ python2 crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 04106505 bus_info_length 4, crc_length 16, crc 25861
404 31333934 bus_name "1394"
408 20001000 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 0, max_rec 1 (4)
40c 0001f200 company_id 0001f2 |
410 0001f32f device_id 000001f32f | EUI-64 0001f2000001f32f
root directory
-----------------------------------------------------------------
414 0004c65c directory_length 4, crc 50780
418 030001f2 vendor
41c 0c0083c0 node capabilities per IEEE 1394
420 8d000006 --> eui-64 leaf at 438
424 d1000001 --> unit directory at 428
unit directory at 428
-----------------------------------------------------------------
428 00035955 directory_length 3, crc 22869
42c 120001f2 specifier id
430 13000009 version
434 17107800 model
eui-64 leaf at 438
-----------------------------------------------------------------
438 000206b2 leaf_length 2, crc 1714
43c 0001f200 company_id 0001f2 |
440 0001f32f device_id 000001f32f | EUI-64 0001f2000001f32f
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For MOTU protocol version 2, this driver arranges the number of data
chunks to align chunks to quadlet data channel. However, MOTU Traveler
has padding bytes in the end of data block at high clock mode.
This commit removes the arrangement. Fortunately, at low and middle clock
mode, supported model for v2 protocol (828mkII) gets no influence from this
change because all of combination for data chunks are just aligned to
quadlet data channel.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU Traveler supports AES/EBU on XLR interface and data block of rx/tx
packet includes two chunk for the interface. This commit adds a flag
for this purpose.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This driver explicitly assumes that all of supported models have main data
chunk separated from chunk for analog ports. However, MOTU Traveler doesn't
support the separated main data chunk.
This commit adds a flag for the separated main data chunk.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In MOTU firewire protocol, data block consists of 24 bit data chunks except
for one quadlet for source packet header (SPH). The number of data chunk in
a data block is different between three clock modes; low, middle and high.
When unit supports ADAT on optical interface, the data block includes some
chunks for ADAT channels. These ADAT chunks are unavailable at high mode.
This driver has local functions to calculate the number of ADAT chunks. But
They uses stack for three clock modes. This is useless for higher mode.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
All UVD instanses have only one dpm control, so it is better
to share one idle_work handle.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use enum amd_powergating_state instead of enum amd_clockgating_state.
The underlying value stays the same, so there is no functional change
in practise. This fixes a warning seen with clang:
drivers/gpu/drm/amd/amdgpu/amdgpu_device.c:1930:14: warning: implicit
conversion from enumeration type 'enum amd_clockgating_state' to
different enumeration type 'enum amd_powergating_state'
[-Wenum-conversion]
AMD_CG_STATE_UNGATE);
^~~~~~~~~~~~~~~~~~~
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Avoid confusing the GART with the GTT domain.
Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
PAGE_SIZE for start_alignment is far much than hw requirement,
And now, update to expereince value from window side.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Marek Olšák <marek.olsak@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
getrawmonotonic64() is deprecated because of the nonstandard naming.
The replacement functions ktime_get_raw_ns() also simplifies the callers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use new return type vm_fault_t for fault handler. For
now, this is just documenting that the function returns
a VM_FAULT value rather than an errno. Once all instances
are converted, vm_fault_t will become a distinct type.
Ref-> commit 1c8f422059 ("mm: change return type to vm_fault_t")
Previously vm_insert_{mixed,pfn} returns err which driver
mapped into VM_FAULT_* type. The new function
vmf_insert_{mixed,pfn} will replace this inefficiency by
returning VM_FAULT_* type.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use new return type vm_fault_t for fault handler
in vm_operations_struct.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit 0ba99ca483 ("block: Add warning for bi_next not NULL in
bio_endio()") breaks the dm driver. end_clone_bio() detects whether
or not a bio is the last bio associated with a request by checking
the .bi_next field. Commit 0ba99ca483 clears that field before
end_clone_bio() has had a chance to inspect that field. Hence revert
commit 0ba99ca483.
This patch avoids that KASAN reports the following complaint when
running the srp-test software (srp-test/run_tests -c -d -r 10 -t 02-mq):
==================================================================
BUG: KASAN: use-after-free in bio_advance+0x11b/0x1d0
Read of size 4 at addr ffff8801300e06d0 by task ksoftirqd/0/9
CPU: 0 PID: 9 Comm: ksoftirqd/0 Not tainted 4.18.0-rc1-dbg+ #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.0.0-prebuilt.qemu-project.org 04/01/2014
Call Trace:
dump_stack+0xa4/0xf5
print_address_description+0x6f/0x270
kasan_report+0x241/0x360
__asan_load4+0x78/0x80
bio_advance+0x11b/0x1d0
blk_update_request+0xa7/0x5b0
scsi_end_request+0x56/0x320 [scsi_mod]
scsi_io_completion+0x7d6/0xb20 [scsi_mod]
scsi_finish_command+0x1c0/0x280 [scsi_mod]
scsi_softirq_done+0x19a/0x230 [scsi_mod]
blk_mq_complete_request+0x160/0x240
scsi_mq_done+0x50/0x1a0 [scsi_mod]
srp_recv_done+0x515/0x1330 [ib_srp]
__ib_process_cq+0xa0/0xf0 [ib_core]
ib_poll_handler+0x38/0xa0 [ib_core]
irq_poll_softirq+0xe8/0x1f0
__do_softirq+0x128/0x60d
run_ksoftirqd+0x3f/0x60
smpboot_thread_fn+0x352/0x460
kthread+0x1c1/0x1e0
ret_from_fork+0x24/0x30
Allocated by task 1918:
save_stack+0x43/0xd0
kasan_kmalloc+0xad/0xe0
kasan_slab_alloc+0x11/0x20
kmem_cache_alloc+0xfe/0x350
mempool_alloc_slab+0x15/0x20
mempool_alloc+0xfb/0x270
bio_alloc_bioset+0x244/0x350
submit_bh_wbc+0x9c/0x2f0
__block_write_full_page+0x299/0x5a0
block_write_full_page+0x16b/0x180
blkdev_writepage+0x18/0x20
__writepage+0x42/0x80
write_cache_pages+0x376/0x8a0
generic_writepages+0xbe/0x110
blkdev_writepages+0xe/0x10
do_writepages+0x9b/0x180
__filemap_fdatawrite_range+0x178/0x1c0
file_write_and_wait_range+0x59/0xc0
blkdev_fsync+0x46/0x80
vfs_fsync_range+0x66/0x100
do_fsync+0x3d/0x70
__x64_sys_fsync+0x21/0x30
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 9:
save_stack+0x43/0xd0
__kasan_slab_free+0x137/0x190
kasan_slab_free+0xe/0x10
kmem_cache_free+0xd3/0x380
mempool_free_slab+0x17/0x20
mempool_free+0x63/0x160
bio_free+0x81/0xa0
bio_put+0x59/0x60
end_bio_bh_io_sync+0x5d/0x70
bio_endio+0x1a7/0x360
blk_update_request+0xd0/0x5b0
end_clone_bio+0xa3/0xd0 [dm_mod]
bio_endio+0x1a7/0x360
blk_update_request+0xd0/0x5b0
scsi_end_request+0x56/0x320 [scsi_mod]
scsi_io_completion+0x7d6/0xb20 [scsi_mod]
scsi_finish_command+0x1c0/0x280 [scsi_mod]
scsi_softirq_done+0x19a/0x230 [scsi_mod]
blk_mq_complete_request+0x160/0x240
scsi_mq_done+0x50/0x1a0 [scsi_mod]
srp_recv_done+0x515/0x1330 [ib_srp]
__ib_process_cq+0xa0/0xf0 [ib_core]
ib_poll_handler+0x38/0xa0 [ib_core]
irq_poll_softirq+0xe8/0x1f0
__do_softirq+0x128/0x60d
The buggy address belongs to the object at ffff8801300e0640
which belongs to the cache bio-0 of size 200
The buggy address is located 144 bytes inside of
200-byte region [ffff8801300e0640, ffff8801300e0708)
The buggy address belongs to the page:
page:ffffea0004c03800 count:1 mapcount:0 mapping:ffff88015a563a00 index:0x0 compound_mapcount: 0
flags: 0x8000000000008100(slab|head)
raw: 8000000000008100 dead000000000100 dead000000000200 ffff88015a563a00
raw: 0000000000000000 0000000000330033 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8801300e0580: fb fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc
ffff8801300e0600: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
>ffff8801300e0680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8801300e0700: fb fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8801300e0780: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
==================================================================
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Fixes: 0ba99ca483 ("block: Add warning for bi_next not NULL in bio_endio()")
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move some s_flags defines out of rdmavt and into hfi1 because they are
hfi1 specific and therefore should remain in the driver instead of
bubbling up to rdmavt.
Document device specific ranges in rdmavt and remap
those in hfi1.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The field is based on a constant that can never change.
Use the define to assign the register instead.
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This field should be in ctxtdata to allow for better locality of access by
eliminating a dd dereference.
The new field is now side-by-side with rcvhdrqentsize since the rhf_offset
is a function of the rcvhdrqentsize.
Both fields are now correctly sized as u8.
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The current implementation precludes having receive context specific
packet type receive handlers.
Fix this by adding adding c99 const array for the existing handlers and
remove the current 72 bytes of pointers from devdata.
A new pointer in hfi1_ctxtdata will point to the const array.
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Replace printk with pr_* to avoid checkpatch warnings.
Signed-off-by: Peter Enderborg <peter.enderborg@sony.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Replace printk with pr_* to avoid checkpatch warnings.
Signed-off-by: Peter Enderborg <peter.enderborg@sony.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Replace printk with pr_* to avoid checkpatch warnings.
Signed-off-by: Peter Enderborg <peter.enderborg@sony.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
We've had a number of users report failures to detect and light up
display with DC with LVDS and VGA. These connector types are not
currently supported with DC. I'd like to add support but unfortunately
don't have a system with LVDS or VGA available.
In order not to cause regressions we should probably fallback to the
non-DC driver for ASICs that support VGA and LVDS.
These ASICs are:
* Bonaire
* Kabini
* Kaveri
* Mullins
ASIC support can always be force enabled with amdgpu.dc=1
v2: Keep Hawaii on DC
v3: Added Mullins to the list
Cc: stable@vger.kernel.org
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>